Filters

List of madhopur Tenders

List of latest madhopur Tenders in Indian Tenders. Click on any madhopur Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for madhopur Tenders.

All-Tenders (1)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49069074 | 15 May, 2025

Tender Value : 3.68 Crore

Madhopur - Rajasthan

Tender for tender for major repair and modernization of existing emrs barnala (raj) - 1 earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 sqm on plan including disposal of excavated earth up to 50 mtr. and lift up to 1.5 mtr. disposed soil to be levelled and neatly dressed : all kinds of soil 2 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 3 supplying and filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand 4 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 5 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 6 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.m20 grade nominal mix / design mix providing m-25 grade concrete by usingcement as per codal provision instead ofm-20 grade design mix. 7 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:nt mortar 1:6 ( 1-cement : 6-sand). 8 anti termite treatment of floor using imidacloprid 30.5% ec non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area dpe 12mm dia termitube system with required number of junction boxes are to be installed. the termitube will run all along the perimeter wall both inside and outside. in the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. after successful testing of termitube, pesticide emulsion of imidacloprid 30.5% ec mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. the plinth area of the area treated will be measured for payment. 9 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. 10 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 11 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mixproviding m-25 grade concrete by usingcement as per codal provision instead ofm-20 grade design mix. 12 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 13 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786) thermo-mechanically treated bars (conforming of relevent is code) 14 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1 : 4 (1 cement : 4 coarse sand) 15 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75cement mortar 1 : 4 (1 cement : 4 coarse sand) 16 carriage of materials:earth,sand ,line morrum,manure or sludge , lead up to 5km 17 filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. 18 random rubble dry stone kharanja under floor. 19 p & f 1st quality heavy duty vitrified double charged tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. size600 mm x 600mm 20 rough chisel dressed sandstone 35 mm thick flooring of approved shade setover 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointingwith cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects : red sand stone (karauli stone) 21 providing and fixing marble stone flooring table rubbed, 15-18 mm thick over 20mm (av.) thick base of cm 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. slabs bhaislana,abu,kishangarh zebra(black marble) above 3601 cm2 slabs 22 extra for providing edge moulding to 15-18mm thick marble/ granite/kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge. granite/kota stone work full edge moulding 23 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish : 20mm thick . 24 extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 25 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3-fine sand) 26 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 27 providing and fixing ist quality mat finished ceremic tile size 300x300mm confirming to is : 13753 coloured tile expect white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler power (untile or roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). 28 providing and fixing pressed steel door frames confirming to is 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with cc 1:2:4(m15 grade) complete as directed by engineer-in-charge :profile c 29 providing and fixing external grade board solid core single leaf flush door shutters isi 2202-67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 35 mm thick commercial veneer both side 30 providing and fixing factory made p.v.c. door frame of size 50x47mm with a wall thickness of5mm, made out of extruded 5mm rigid pvc foam sheet mitred at corners and joined with 2 nos. of 150mm long brackets of 15x15mm m.s. square tube, the vertical door profiles to be reinforced with 19x19mm m.s. square tube of 19 gauge, epdm rubber gasket weather seal to be provided through out the frame. the door frame to be fixed to the wall using m.s. screws of 65/100mm size complete as per manufacturers specification and direction of engineer-in-charge. 31 providing and fixing to existing door frames. 30mm thick factory made solid panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15 mm x15mm , top & bottom rails. m.s .frame shall have a coat of steel primers of approved make and manufacture m.s. frame covered with 5mm thick heat moulded pvc ‘c channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 95mm wide pvc sheet out of which 75 mm shall be flat and 20mm shall be tapered in 45 degreeon the inner side to form top and bottom rail and 115mm wide pvc sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail. top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross pvc sheet shall be provided as gap insert for top rail & bottom rail. panelling of 5mm thick pvc sheet to be fitted in the m.s. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide pvc sheet bending on inner side, and joined together with solvent cement adhesive. an additional 5mm thick pvc strip of 20mm width is to be stuck on the interior side of the ‘c channel using pvc solvent adhesive etc. complete as per direction of engineer-in-charge, manufacture’s specification & drawing.(for w.c.and bathroom door shutter). 32 providing and fixing of upvc casement openable windows (outward / inward): outer frame made from the extruded upvc windows profile section of size 60w x 60h mm having outer wall thickness of 2.5mm (+/- 0.2mm) and three chamber constuction, white in finish, duly reinforced with 1.5mm thick gi section. all the four corners shall be mitered cut & thermal welded so as to form window frame. frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. fix mullion made of 60w x 80h mm upvc profile section with steel reinforcement shall be provided in windows having 2 or more openable shutters, as per the requirement. frame shall have co-extruded with epdm/tpe-e gasket fitted in in-built groove of frame profile for proper air & sound insulation of the shutter.the shutter of outward openable window shall be made of size 60w x 74h mm and shutter of inward openable window shall be made of size 60w x 77h mm extruded 3 box multi-chamber upvc window profile section of white colour having outer wall thickness of 2.25mm (+/- 0.2mm) provided with reinforcement of 1.5mm thick gi section duly mitered cut & thermal welded at all corners and fitted with upvc glazing bead of size 36 x 20mm with inner and outer co-extruded epdm/tpe-e weather seal gasket alongwith 6mm thick isi make plain float glass. all welding joints of frame and shutter shall be cleaned and milled with the cnc mechainism to provide uniform grooved finish on all visible jaints. hardware: window shutter are fixed with frame on 2.5mmthick ss301 grade friction hinge system to keep the window opened at desired angle. friction hinge also enables easy cleaning of glass on both side from the inside of building. 33 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete new plastered surface (three or more coats) 34 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 35 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provisionnew work 36 painting with synthetic enamel paint of approved brand and manufacture togive an even shade :two or more coats on new work 37 french sprit polishing : two or more coats on new work including a coat of wood filler 38 providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). grade 304 39 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 40 grading roof for water proofing treatment withwater proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 41 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 42 providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 kg/sqm) on top of hot bitumen @ 1.7 kg/sqm. (1.40 kg ofvg-40 (30/40 )grade and 0.30 kg/sqm. ofvg-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of engineer-in-charge. 43 providing and fixing in position collapsible steel shutters with vertical m.s. channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of t-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (to be measured and paid as per outer dimension). 44 making grooves as per design in plaster 10mm to 20mm wide. 45 making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over p.v.c. sheet 1 mtr. x 1 mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. 46 providing and laying damp-proof course with cement concrete grade m-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . 50mm thick. 47 filling of sunk portion of roof with earthen pots of required height including filling voids with 1:3:6 light concrete, using brick batscomplete levelling and dressing the surface by 50mm thick cement concrete 1:2:4 as per specification. 48 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @0.253 kg//sqm .this layer will be allowed to air cure for 4 hours. (ii) second layer of slurryof cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm this layer will be allowed to air cure for4 hours followed by water curing for 48 hours. the rates includes preparation of surface treatment & sealing of all joints ,corners,junction with polymer mixed slurry. 49 providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm 50 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer- in – charge .(glazing and paneling to be paid for separately). for fixed portionpolyester powder coating aluminum( minimum thickness of powder coating 50 micron) 51 providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade i, type ii conforming to is : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. pre-laminatedparticleboardwithdecorativelaminationononesideandbalancinglaminationonotherside. 52 providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(cost of aluminium snap beading shall be paid in basicitem.) with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) 53 providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 54 providing and fixing sun control film, thickness of film 1 mil visible light transmittance 4-24% & solar energy transmittance 42-51% & total solar energy rejection 37-43%of approved colour and shade , complete in all respect , at all level , as directed by engineer- in -charge. 55 providing and fixing double action hydraulic floor spring of approved brand and manufacture is : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece m.s. 56 s&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. 57 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor:size 530x410mm. 58 p & f european type white glazed vitreous china 1st quality double syphonic w.c (is :2556 mark) with p or s trap including cutting and making good the wall and floor 59 p & f 15 mm. dia connection pipe of approved quality/make :600 mm dia 60 p & f kitchen & lab. sink of approved make with c.i. brackets duly painted, 40 mm c.p. waste coupling, c.p. brass chain with rubber plug, 40 mm g.i. waste pipe up-to floor level complete including cutting and making good the wall & floor : fire clay glazed kitchen sink (i.s 771-1985marked) size 600 x 450 x 250mm. 61 p & f full-way valve (is:778 mark) or wheel valve of approved make : 62 gun-metal 15mm nominal bore. 63 gun-metal 25mm nominal bore. 64 p & f looking mirrors with p.v.c. frame of approved (atul modi guard saint gobin or equivalent)size 500 x 400 mm 65 p & f towel rail or ring of approved quality/ make: 66 c.p. brass towel rail with brackets 600x 20 mm 67 c.p. brass towel ring revolving type 68 p & f grating of approved quality /makestainless steel sheet size 125 mm diaheavy quality of approved make 69 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes (is 15778 : 2007 code) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. (concealed work including cutting chases and making good the walls etc.,) 70 15mm dia nominal bore 71 25mm dia nominal bore 72 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes (is 15778 : 2007 code) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings, this included jointing of pipes & fittings with one step cpvc solvent cement , trenching refilling & testing of joints complete as per direction of engineer in charge.(external work). 73 15mm dia nominal bore 74 25mm dia nominal bore 75 p & f bib cock (is : 8931 mark), superior quality of approved make: c.p. brass bib cock, 15 mm nominal bore 76 p & f stop cock (is :8931 mark), superior quality & of approved make: c.p. brass 15 mm nominal bore. 77 p&f soap dish or tray of approved quality/ make. c.p. brass heavy and superior quality 78 p&f bath shower of approved quality/ make . c.p. brass of heavy & superior quality 150mm. 79 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection 15 mm brass (is:8931 marked)with 60 cm long thread and nut. 80 p & f ball cock (is :1703 mark) with rod & p.v.c. ball complete : brass wt.400 gm,15mm. 81 p & f pvc storage tank (is : 12701marked indicating the bis license no), of approved make with cover, 25mm dia 1m long g.i. over-flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000 litres capacity. 82 hoisting charges for each floor : 83 construction of manhole in all type of soil inner size 90 x 60 cm. 300 mm thick masonry in cm 1:6, 10 cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring, making channels, 80mm thick stone slab covering with 40mm thick m-15 grade c.c. flooring, cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. depth up to 0.5 m 84 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m,10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. size 450 x 450mm depth upto0.5 m cement cover with frame 85 construction of septic tank in all types of soil with 40 cm .thick masonry in cm 1:6, 15 cm thick c.c bed of 1:5:10, m-15 gradec.c floor &rcc slab covering with m15 grade c.c. floor,50 mm thick stone slab partition walls, 20 mm thick plaster in cm 1:6 finished with neat floating cement, 4 nos stone foot rests of approved design ,two no. 450 mm dia each ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-size 400 x140x150 cm.(for 50 users)with 115 mm thick rcc (m-20) slab with tor steel reinforcement 10mm ? @15 cm c/c bothways including shuttering complete in all respect 86 construction of open surfacedrain with 112mm thick brick masonry in cm 1:4,110mm thick base concrete 1:5:10, 37mm thick m-15 grade c.c. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing: 150mm drain,225mm av. depth 87 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 88 75mm dia 89 110mm dia 90 160mm dia 91 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 92 plain tee 110 mm 93 vent covel 75mm 94 plain floor trap 110mm dia 95 bend 87.5 - 75mm 96 bend 87.5 - 110mm 97 pipe clip- 110mm 98 coupler-110 mm dia 99 making connection of g.i. distribution branch with g.i. main including all fitting. beyond 25mm & upto 100mm dia 100 construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in cm 1:6, 80mm thick stone slab, jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m-15 grade c.c flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: size 300 cm. dia outside & 300 cm. depth . 101 p & f water closet seat covers with brass hinges complete : solid pvc (is 2548 marked) grade-i black for ewc. 102 p & f low level flushing cistern of 10 litres capacity (is : 2556 mark) of approved make with complete fittings c.i. brackets duly painted, brass ball cock with ball (is: 1703 mark) complete including cutting and making good the wall: pvc withpvcbend and superior internal fittings as per is : 7231 . 103 p & f jet spray for water closet with c.p. copper tube flange of approved make. 104 p & f wvc wash basin (ist quality is:2556 mark) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock (is:8934 mark) & 32 mm c.p. brass waste coupling of approved make, p.v.c waste pipe with pvc nut 32 mm complete including cutting & making good the wall : size 580 mm x 450 mm 105 p & f flush cock/flush valve (is:9758 mark) or wc of approved quality make : c.p. brass push type exposed 25 mm nominal bore. 106 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 6 (1 cement : 6 coarse sand) 107 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto five levelabove 30cm. thick walls in : 108 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead with cement mortar 1 :4 ( 1 cement : 4 coarse sand) 109 patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. 110 labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. 111 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection 15mm.brass (is : 8931 marked) 112 p & f 15 mm. dia connection pipe of approved quality/make : cp brass pipe with cp brass nuts upto length 600mm. 113 providing & fixing premium quality white glazed vitreous china sanitary wares (is:2556 mark) of approved make as per direction of engineer-in-charge including cutting and making good the wall and floor. double syphonic european w.c. with mounted w.v.c. flushing cistern of 10 litre capacity complete with all necessary internal fittings with hydraulic seat cover. 114 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor: size 580x440mm. 115 providing and fixing t-iron frames for doors, windows and ventilators of mild steel tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 116 providing and fixing fully panelled/partly panelled/double leaf shutter frames for doors as per approved design and drawings with approved ordinary c.p./ oxidised steel fittings as per annexure - a and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm x 12mm on both faces complete : 35 mm thick nigeria wood grade i 117 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completeold plastered surface (two or more coats) 118 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:old work (one or more coats ) two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.old work (one or more coats ) 119 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision old work 120 providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 kg/sqm) on top of hot bitumen @ 1.7 kg/sqm. (1.40 kg ofvg-40 (30/40 )grade and 0.30 kg/sqm. ofvg-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of engineer-in-charge. 121 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 122 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 123 providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 cm long embedded in c cblock 15 x 10 x 10 cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, u shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of engineer-in –charge window openable. 124 providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre length) up to 3m height of wall with existing angle iron y shaped placed 2.4 m or 3.00 m apart and with 9 horizontal r.b.t. stud tied with gi staples and gi clips to retain horizontal including necessary bolts or gi barbed wire tied to angle iron all complete as per direction of engineer in charge with reinforced barbed tape (r.b.t.)/spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/metre (cost of ms angle, cc block shall be paid extra) 125 renewing glass panes,with putty and nails wherever necessary float glass panes of thickness 4 mm 126 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size). 127 kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm 128 earth work in excavation by mechanical means (hydraulic excavator ) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed : all kinds of soil

Related Locations of : Rajasthan

List of madhopur Tenders

Get madhopur Tender Alert...

Related Locations of : Rajasthan

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us