Indian Tenders Tender information of India
Global Tenders International Tender information
Projects Project information of India
Tender Awarded Tender awarded information
Sub-Contractor Vendor information of India
Pay Online
Register now
Login
Contact Info All India : 9276083333 / 9274315555 South India : 9274315555

Filters

List of grinding-roller-scrap Tenders

List of latest grinding-roller-scrap Tenders in Indian Tenders. Click on any grinding-roller-scrap Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for grinding-roller-scrap Tenders.

All-Tenders (4)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

corporations/Associations/Others

TRN :49056804 | 23 May, 2025

Tender Value : 18.27 Lacs

Prayagraj - Uttar Pradesh

Tender for tender for annual civil & electrical m&r work for residential building situated at 20-clive road hydel colony, prayagraj - earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. for all kinds of soil. 2 supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. 3 surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. for all kinds of soil. 4 excavating, supplying, stacking and filling of local earth by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 5 providing and laying in position cement concrete of grade 1:1½:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 6 providing and laying in position cement concrete of grade1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 7 providing and laying in position cement concrete of grade 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 8 providing and laying cement concrete 1:1½:3 (1 cement: 1½ coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 9 providing and fixing up to floor five level precast cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering complete. 10 providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 11 extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturers specification. 12 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 13 providing and laying in positiongrade 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 14 providing and laying in positiongrade 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 15 reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 16 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 17 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 18 centering and shuttering including strutting, propping etc. and removal of form for walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 19 centering and shuttering including strutting, propping etc. and removal of form forsuspended floors, roofs, landings, balconies and access platform 20 centering and shuttering including strutting, propping etc. and removal of form for shelves (cast in situ) 21 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 22 centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts 23 centering and shuttering including strutting, propping etc. and removal of form for stairs, (excluding landings) except spiral-staircases 24 centering and shuttering including strutting, propping etc. and removal of form for spiral staircases (including landing) 25 centering and shuttering including strutting, propping etc. and removal of form for small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 26 centering and shuttering including strutting, propping etc. and removal of form for small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like 27 centering and shuttering including strutting, propping etc. and removal of form for weather shade, chajjas, corbels etc., including edges 28 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick 29 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick 30 mild steel and medium tensile steel bars for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 31 mild steel and medium tensile steel bars for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 32 smooth finishing of the exposed surface of r.c.c. work with 6 mm thick cement mortar 1:3 (1 cement : 3 fine sand). 33 add for plaster drip course/ groove in plastered surface or moulding to r.c.c. projections. 34 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) 35 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand) 36 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement : 4 coarse sand) 37 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 (1 cement :4 coarse sand) 38 providing and fixing 18 mm thick granite stone slab of colour black, cherry/ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels (area of slab over 0.50 sqm) 39 providing edge moulding to 18 mm thick granite workcounters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge. 40 extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 41 providing and fixing plywood 4 mm thick, one side decorative veneer conforming to is: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : 42 providing and fixing 4mm thick coir veneer board, isi marked is : 14842, plain lining with necessary screws, priming coat on unexposed surface etc., complete. 43 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 44 providing second class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 45 providing and fixing 2nd class teak wood size 50x12 mm moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 46 providing and fixing second class teak wood panelled or panelled and glazed 30 mm thick shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of engineer-in-charge. (note:- butt hingesand necessary screwsshall be paid separately) 47 providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 48 providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 49 providing and fixing30mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned and chemically treated hollock wood) 50 providing and fixing35mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned selected planks of sheesham wood) 51 providing and fixing30mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned selected planks of sheesham wood) 52 providing and fixing30mm thick panelled or panelled & glazed shutters for cup board using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(second class teak wood including isi marked anodised aluminium butt hinges with necessary screws) 53 providing and fixing isi marked 35mm thick flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 54 providing and fixing isi marked 30mm thick flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 55 providing and fixing isi marked 35mm thick flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 56 extra for providing and fixing flush doors with on one side only decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 (part i) 57 providing and fixing 12mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 58 providing and fixing 20mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 59 providing and fixing 25mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 60 providing and fixing 20mm dia (heavy type) nickel plated m.s. pipe curtain rods with nickel plated brackets : 61 providing and fixing 25mm dia (heavy type) nickel plated m.s. pipe curtain rods with nickel plated brackets : 62 providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. 63 providing and fixing 125x65x2.12 mm isi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 64 providing and fixing 100x58x1.90 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 65 providing and fixing 75x47x1.70 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 66 providing and fixing 50x37x1.50 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 67 providing and fixing 150 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 68 providing and fixing 125 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 69 providing and fixing 100 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 70 providing and fixing 250x16 mm isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete (copper oxidised as per is 1378) 71 providing and 250x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 72 providing and 200x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 73 providing and 150x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 74 providing and 100x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 75 providing and fixing isi marked 85x42 mm oxidised m.s. pull bolt lock conforming to is : 7534 with necessary screws bolts, nut and washers etc. complete (copper oxidised as per is 1378). 76 providing and fixing 125 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 77 providing and fixing 100 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 78 providing and fixing 75 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 79 providing and fixing 150 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 80 providing and fixing 115 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 81 providing and fixing 90 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 82 providing and fixing 300 mm (weighing not less than 330 grams) oxidised m.s. casement stays (straight peg type) with necessary screws etc. complete (copper oxidised as per is 1378) 83 providing and fixing 125mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 84 providing and fixing 100mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 85 providing and fixing 75mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 86 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 87 providing and fixing triple strip vertical type magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 88 providing and fixing double strip (horizontal type) magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 89 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge (extruded section profile size 48x40 mm) 90 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge (extruded section profile size 42x50 mm) 91 providing and fixing 12 mm thick fire retardant plywood conforming to is: 5509 panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 92 providing and fixing cup board shutters 25 mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board is: 12823 marked, exterior grade (grade l type ll), having one side decorative lamination and other side balancing lamination, including iind class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the engineer-in-charge 93 providing and fixing aluminum u beading of required size to pre-laminated/flush door shutter, including fixing etc. complete as per direction of engineer-in-charge. 94 providing and fixing casement handle made of zinc alloyed (white powder coated) for upvc casement window with necessary screws etc. complete. 95 providing and fixing zinc alloyed (white powder coated) touch lock for upvc sliding window with necessary screws etc. complete. 96 providing and fixing steel roller for upvc sliding window with necessary screws etc. complete. 97 providing and fixing steel roller for upvc sliding door with necessary screws etc. complete. 98 providing and fixing steel (white power coated) crescent lock for upvc sliding window/ door with necessary screws etc. complete. 99 providing and fixing 18mm thick both sides pre-laminated cement bonded wood particle board as per is : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of engineer-in-charge (note: fittings to be paid separately). 100 providing and fixing 6mm thick both sides pre-laminated cement bonded wood particle board as per is : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of engineer-in-charge. 101 providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed bwp grade marine ply as per is 710 of approved brand including 2mm thick pvc edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of engineer-in-charge.(payment of providing and fixing auto closing hinges shall be paid separately) 102 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 103 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 104 providing and fixing 1mm thick m.s. sheet door with frame of 40x40x6 mm angle iron and 3 mm m.s. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.(using m.s. angels 40x40x6 mm for diagonal braces) 105 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 106 providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing t-iron frame or to the wall with dash fastener,including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of engineer-in-charge. 107 brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar with 1:6 (1cement : 6 coarse sand) including filling the joints with same mortar, with common burnt clay non modular bricks: 108 dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks. 109 40 mm thick with 20 mm nominal size stone aggregate cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 110 18 mm thick cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 111 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 112 cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. 113 25 mm thick kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 114 deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. 115 fixing glazed/ ceramic/ vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (water based) conforming to is: 15477, in average 3mm thickness. 116 kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 117 providing and fixing 1st quality ceramic glazed floor tiles conforming to is : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 118 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. 119 providing and laying vitrified floor tiles size 600x600 mm(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. 120 providing 1 mm thick with zinc coating not less than 275 gm/ m² corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 121 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over p.v.c. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 122 providing & fixing 0.56 mm, aluminium color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm at all heights, levels and locations colour finish aluminium alloy roofing sheets of alloyis designation31500, temper hx8 conforming to is 737 and dimensions as per is code 2676 with characteristics of good formability and corrosion resistance. the profile sheets shall be fixed to truss members in slope or required pitch or curvature with hex cap headed self drilling/tapping stainless steel screws m6, 50 mm long with 3 mm epdm seal washer etc. all inclusive of labour, scaffolding, t&p and sundries etc. complete as per directions of the engineer-in-charge. (cost of truss/frame work shall be paid separately). 123 providing and fixing precoated/mill finish aluminium ridges plain (500- 600mm) of pre-coated colour or mill finishaluminium roofing accessories in 0.71 mm thickness ,alloy 31500 (is designation) [aluminium alloy (aa) 3004 (iso designation)]for color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping ss screws of size 6 x 50mm with 3mm thick epdm seal and ss plain washer complete : 124 providing 10 mm thick plaster of paris (gypsum anhydrous) flat surfaces ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): 125 12.5 mm thick fully perforated gypsum board tile made from plasterboard having glass fibre conforming to is: 2095 part i, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an nrc (noise reduction coefficient) of 0.79, with 50 mm resin bonded glass wool backing. 126 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) 127 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 128 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) 129 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) 130 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) 131 neat cement punning. 132 distempering with 1st quality acrylic distemper (ready mixed) new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than50 gram/litre of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 133 finishing walls for new work (two or more coats applied @ 3.84 kg/10 sqm) with water proofing cement paint of required shade : 134 finishing walls for new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) with acrylic smooth exterior paint of required shade : 135 finishing walls for new work (two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. with ready mixed premium acrylic emulsion paint (company depot tinted) having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shadewith silicon additives. 136 with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 137 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 138 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) 139 painting (two or more coats) on 100mm diameter rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 140 painting (two or more coats) on 150mm diameter rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 141 painting two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 142 polishing on new wood work with ready mixed wax polish of approved brand and manufacture : 143 lettering with black japan paint of approved brand and manufacture 144 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 145 distempering for old work (one or more coats) with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturerincluding applying additional coats wherever required to achieve even shade and colour 146 applying priming coats with water thinnable cement primer on wall surface having voc content less than 50 grams/litre of approved brand and manufacture. 147 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of engineer-in-charge. 148 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 149 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 150 polishing on old wood work with ready made wax polish of approved brand and manufacture : 151 painting (one or more coats) with black japan paint of approved brand and manufacture to give an even shade. 152 finishing walls for old work (two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface with acrylic smooth exterior paint of required shade : 153 repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 154 fixing door chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 155 fixing chowkhat in existing opening in brick/ rcc wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including cost of dash fasteners/ chemical fastener. 156 making the opening for door/ window/ clerestory window in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of engineer-in-charge. 157 renewing float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) with putty and nails wherever necessary including racking out the old putty: 158 renewing float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) with putty and nails wherever necessary including racking out the old putty: 159 renewal of old putty of glass panes (length) 160 refixing old glass panes with putty and nails 161 fixing old glass panes with wooden fillets (excluding cost of fillets) 162 renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer. 163 pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 164 providing and fixing 20 mm diameter. brass curtain rods ofwall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 165 repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of engineer-in-charge. 166 cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of engineer-in-charge. 167 disconnecting damaged overhead/terrace pvc water storage tankof any size from water supply line and removing from the terrace including shifting at ground level as per direction of engineer-in-charge. 168 providing & fixing orissa pattern w.c pan of size 580x440 mm white vitreous china water closet squatting pan (indian type) along withs or p trap including dismantling of old wc seat and s or p trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. 169 dismantlingw.c.pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of engineer-in-charge. 170 dismantling 15 to 40 mm dia g.i. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of engineer-in-charge.(a) internal work- exposed on wall 171 taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the engineer-in-charge. 172 demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of engineer- in-charge. 173 demolishing nominal cementconcrete 1:3:6 or richer mix (i/c equivalent design mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 174 demolishing nominal cementconcrete 1:4:8 or leaner mix (i/c equivalent design mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 175 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. 176 demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. 177 removing mortar from bricks in from brick work in cement mortar and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): 178 dismantling doors, windows and clerestory windows (steel or wood) shutter of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 179 dismantling doors, windows and clerestory windows (steel or wood) shutter of area beyond 3 sq. metres including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 180 taking out doors, windows and clerestory window shutters (steel or wood) of area 3 sq. metres and belowincluding stacking within 50 metres lead : 181 taking out doors, windows and clerestory window shutters (steel or wood) of area beyond 3 sq. metres including stacking within 50 metres lead : 182 dismantling for thickness of tiles 10 mm to 25 mmwork in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 183 dismantling for thickness of tiles above 25 mm and up to 40 mmwork in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 184 demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : 185 dismantling g.s. sheetroofingincludingridges,hips,valleysandguttersetc., and stacking the material within 50 metres lead of: 186 dismantling asbestos cement sheetroofingincludingridges,hips,valleysandguttersetc., and stacking the material within 50 metres lead of: 187 dismantling tiled roofing with battens, boarding etc. complete includingstackingofserviceablematerialanddisposalofunserviceable material within 50 metres lead. 188 dismantlingbarbedwireorflexiblewireropeinfencingincludingmaking rolls and stacking within 50 metres lead. 189 dismantling40 mm thick precast concrete orstone slabsin walls, partition walls etc. including stacking within 50 metres lead : 190 dismantling40 mm to 75mmthick precast concrete orstone slabsin walls, partition walls etc. including stacking within 50 metres lead : 191 dismantling cement asbestos or other hard board ceiling or partition wallsincludingstackingofserviceablematerialsanddisposalof unserviceable materials within 50 metres lead. 192 dismantling of flushing cistern of all types(c.i./pvc/vitrious china) includingstackingofusefulmaterialsnearthesiteanddisposalofunserviceable materials within 50 metres lead. 193 dismantling old plaster or skirting raking out joints and cleaning the surfaceforplasterincludingdisposalofrubbishtothedumping ground within 50 metres lead. 194 dismantlingaluminium/gypsumpartitions,doors,windows,fixed glazing and false ceiling including disposal of unserviceable material andstackingofserviceablematerialwithin50metersleadas directed by engineer-in-charge. 195 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping groundorasapprovedbyengineer-in-charge,beyond50minitial lead, for all leads including all lifts involved. 196 cuttingroadandmakinggoodthesameincludingsupplyofextra quantities of materials i.e. aggregate, moorum screening, red bajri and labour (required.bituminous portion) 197 paintingroadsurfacemarking for new work (two or more coats) withadequatenosofcoatstogive uniform finish with ready mixed road marking paint conforming to is : 164, on bituminous surface in white/yellow shade, including cleaning thesurfaceofalldirt,scales,oil,greaseandforeignmaterialetc. complete. 198 paintingroadsurfacemarking for old work (one or more coats) withadequatenosofcoatstogive uniform finish with ready mixed road marking paint conforming to is : 164, on bituminous surface in white/yellow shade, including cleaning thesurfaceofalldirt,scales,oil,greaseandforeignmaterialetc. complete. 199 taking out existing cc interlocking paver blocks from footpath/ central verge,includingremovalofrubbishetc.,disposalofunserviceable materialtothedumpingground,forwhichpaymentshallbemade separately and stackingof serviceable materialwithin 50metre lead as per direction of engineer-in-charge. 200 layingoldcementcocreteinterlockingpaverblocksofanydesign/ shapelaidinrequiredline,level,curvature,colourandpatternover and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer- in-charge. (old cc paver blocks shall be supplied by the department free of cost). 201 providing and laying 80mmthickc.c.paverblockofm-35gradewith approved colour design and pattern.factory made chamfered edge cement concrete paverblocksinfootpath,parks,lawns,drivewaysorlighttraffic parkingetc,ofrequiredstrength,thickness&size/shape,madeby tablevibratorymethodusingpumould,laidinrequiredcolour& patternover50mmthickcompactedbedof sand,compactingand properembedding/layingofinterlockingpaverblocksintothesand beddinglayerthroughvibratorycompactionbyusingplatevibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. completeall as per direction of engineer-in-charge. 202 providing andfixingwhitevitreouschinaorissapatternw.c.panofsize 580x440 mm with integral type foot rests waterclosetsquatting pan(indian typew.c. pan)with100mmsandcastironporstrap,10litrelowlevel whitep.v.c.flushingcistern,includingflushpipe,withmanually controlleddevice(handlelever)conformingtois:7231,withall fittingsandfixturescomplete,includingcuttingandmakinggood the walls and floors wherever required: 203 providing and fixing w.c. pan with isi marked white solid plastic seat and lid white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard makeandmosquitoproofcouplingofapprovedmunicipaldesign complete,includingpaintingoffittingsandbrackets,cuttingand making good the walls and floors wherever required : 204 providingandfixing oneurinalbasinwith5litrewhitep.v.c.automaticflushing cistern whitevitreouschinaflatbackorwallcorner typelippedfronturinalbasinof430x260x350mmand 340x410x265 mm sizes respectively with automatic flushing cistern withstandardflushpipeandc.p.brassspreaderswithbrass unions and g.i clamps complete, including painting of fittings and brackets,cuttingandmakinggoodthewallsandfloorswhereverrequired : 205 providingandfixingwhitevitreouschinawashbasinsize550x400mm with a pair of 15 mm c.p. brass pillar taps washbasinwithc.i.brackets,15mmc.p. brasspillartaps,32mmc.p.brasswasteofstandardpattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 206 providing and fixing wash basin with c.i. brackets, 15 mm dia cp brasssingleholebasinmixerofapprovedqualityandmake, including painting of fittings and brackets, cutting and making goodthe walls wherever required:- (a)white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer 207 providingandfixingwhitevitreouschinapedestalforwashbasin completelyrecessedatthebackforthereceptionofpipesand fittings. 208 providing and fixing 610x510 mm bowl depth 200 mm stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required (kitchen sink without drain board) 209 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer - in - charge. 210 providing and fixing 10 litre capacity - white p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete. 211 providing and fixing 10 litre (full flush) capacity-white controlled flush, low level cistern made of vitreous china with all fittings complete. 212 providing and fixing g.i. inlet connection for flush pipe connecting with w.c. pan. 213 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer-in-charge. 214 providing and fixing15 mm nominal dia cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge. 215 providingandfixing 32mm diaflexible pipe p.v.c.wastepipeforsinkorwashbasin including p.v.c. waste fittings complete. 216 providing and fixing 100 mm sand cast iron grating for gully trap. 217 providingandfixinginposition25mmdiametermosquitoproofcoupling of approved municipal design. 218 providing and fixing 600x450 mm beveled edge mirror of superior glass(ofapprovedquality)completewith6mmthickhardboard ground fixed to wooden cleats with c.p. brass screws and washerscomplete. 219 providing andfixing circular shape 450 mm dia mirrorofsuperiorglass(ofapprovedquality)andofrequiredshapeandsizewithplasticmouldedframeof approved make and shade with 6 mm thick hard board backing : 220 providing andfixing 600x120x5 mmglass shelfwith edges round off, supported on anodised aluminium angle frame with c.p. brass bracketsandguardrailcompletefixedwith40mmlongscrews, rawl plugs etc., complete. 221 providing and fixing c.p. brass toilet paper holder : 222 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 223 providing and fixing ptmt towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. 224 providing and fixing ptmt 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 225 providing and fixing ptmt 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 226 providing and fixing ptmt shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. 227 providing and fixing ptmt 15 mm urinal spreader size 95x69x100 mm with 1/2 bsp thread and shapes, weighing not less than 60 gms. 228 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 229 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 230 providing and fixing 25 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 231 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 232 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 233 providing and fixing 25 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 234 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 235 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 236 providing and fixing 25mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 237 providing and fixing 32mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 238 providing and fixing 40mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 239 providing and fixing 50mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 240 providing and fixing 15 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 241 providing and fixing 20 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 242 providing and fixing 25 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 243 providing and fixing 15 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 244 providing and fixing 20 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 245 providing and fixing 25 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 246 providing and fixing 32 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 247 providing and fixing 40 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 248 providing and fixing 50 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 249 providing and fixing 25 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 250 providing and fixing 20 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 251 providing and fixing 32 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 252 providing and fixing 15 mm nominal bore ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 253 providing and fixing 20 mm nominal bore ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 254 providing and fixing 15mm norminal bore 45 cm length uplasticised pvc connection pipe with brass unions : 255 providing and fixing 20mm norminal bore 45 cm length uplasticised pvc connection pipe with brass unions : 256 providing and fixing 100 mm diameter c.p. brass shower rose with 15 or 20 mm inlet : 257 providing and fixing 150 mm diameter c.p. brass shower rose with 15 or 20 mm inlet : 258 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 259 providing and fixing 15 mm nominal bore c.p. brass bib cock of approved quality conforming to is:8931 : 260 providing and fixing 15 mm nominal bore c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 261 providing and fixing 15 mm nominal bore c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms. 262 providing and fixing 15mm nominal bore c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 263 providing and fixing c.p. brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of engineer-in-charge. 264 cutting holes up to 15x15 cm in r.c.c. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 265 providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fastenersto be paid for separately) :(for fixed portion) 266 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fastenersto be paid for separately) :(for fixed portion) 267 providing and fixing glazing with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 268 providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 269 providing and fixing glazing with float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 270 providing and fixing with stainless steel cover plate minimum 1.25 mm thicknessdouble action hydraulic floor spring of approved brand and manufacture conforming to is : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. 271 providing and fixing with brass cover plate minimum 1.25 mm thicknessdouble action hydraulic floor spring of approved brand and manufacture conforming to is : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. 272 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. this layer will be allowed to air cure for 4 hours.(b) second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) 273 providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of fibre glass cloth when the first layer is still green. overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. (for the purpose of measurement the entire treated surface will be measured.) 274 providing & applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer(dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of engineer-in-charge. 275 providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of rcc structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. after cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. over the primed surface swellable type water stop tape shall be placed. the work shall be carried out all complete as per specification and the direction of the engineer-in-charge. the product performance shall carry guarantee for 10 years against any leakage. 276 providing and fixing with15mmthick fullyperforatedsquare/buttedgelightweightcalcium silicate panels/ tiles in position wall panelling at all heights with integral densified calcium silicatepanels/tilesofsize595x595mm,havingnrc(noisereductioncoefficient)of0.50 (minimum) as per is 8225:1987, light reflectance of 85% (minimum). non combustible as per bs:476 (part-4), fire performance as per bs:476 (part 6 &7), humidity resistanceof 100%,thermalconductivity<0.043w/mk asperastm518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mmthickpressedsection(galvanizing@120gramspersqmincludingbothsides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor andceilingchannel sectionofsize50x32mfixedtothefloorandsoffitat600mm centersusing12mmdia,50mmlongwedgetypeexpandedzincalloy dashfastnerwith 10mm bolt. this same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. glasswool of 50mm thickness is then to be inserted in the slots and finallycalcium silicate non combustible panels/tiles are to bescrew fixed withselftapping panheadnickel coatedmild steelscrewsofsize13x3.2mmon tothisgridleavingan evengroove of1 mm betweenthepanels. the joints betweenthepanelsaretobedulyjointedandfinishedusingrecommendedjointing calcium silicate based compound and fiber joint tape roll 50mm wide(90 metre )roll and twocoatsofprimersuitableforpanellingaspermanufacturersspecificationasper direction of engineer-in-charge all complete. 277 providing and fixing with 16 mm thick beveled tegular mineral fibre false ceiling tile (nrc 0.55 to 0.6 mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance (rh) of 99%,lightreflectance=85%,thermalconductivityk=0.052-0.057w/mk,fire performance as per (bs 476 pt - 6 &7)in true horizontal level suspended on interlocking t- grid of hot dipped all round galvanized iron section of 0.33 mmthick (galvanized @120 gsm)comprisingofmaintrunnersof15x32mmoflength3000mm,crosstofsize 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length600mm toform gridmoduleofsize 600x600mm suspendedfrom ceiling using galvanizedmildsteelitem(galvanised@80gsm)50mmlong8mmouterdiameterm-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l- shapeleveladjusterofsize85x25x2mm,spacedat1200mmcentretocentrealong main‘t’.thesystemshouldrestonperipherywalls/partitionswiththehelpofgi perimeter wall angle of size24x24x3000 mm made of 0.40 mm thicksheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry walls.s. screws. the exposed bottom portion of all t-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. the work shall be carriedoutasperspecifications,drawingsandasperdirectionsoftheengineer-in- charge. 278 providingandfixingharddrawnsteelwirefabricofsize75x25mmmeshorother suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 279 fillingofjointsbetweenrccplinthbeam/floorslabandwallpanelofexternalwalls, toilet / bath room / wet areas walls on all floor and parapet wall over roof slab, stair case headroomatthetimeoferectionofgfrgpanelswithgroutrw/equivalentsealant compound after the erection of panelbeforethe infill of concrete in panel cavities and fine finish. this applies for all horizontal and vertical joints between gfrg wall and slab panels. 280 waterproofingtreatmentofverticaljoints(ofexternalsideandinternalside)between doorframe,window&ventilatorframes(onallfoursides)ofouterwalloverthe zycosil/equivalent & zycoprime/equivalent solution already applied (before the installation of door / window / ventilator frames in position) and fine finish with grout rw/equivalent. 281 waterproofingtreatmentofrccsunshadewith zycosil/equivalentwaterproofing solution(1litreofzycosil/equivalent&20litresofwaterstirredfirst&2litresof zycoprime/equivalent addedandstirred (total23litres))till itmeetsthesaturationlevel and testing as per rilem or bywater drops test in which water drops do not absorb but drops remain or rolls. 282 in-filling / sealing of joint between rcc lintel cum sunshade and wall (on external side) in all floors by pushing in grout rw/equivalentin paste form and coving 20 mm x 20 mm after applying a coat of zycosil/equivalent & zycoprime/equivalent solution before cement plastering of top, bottom and sides of rcc sunshade. 283 concreteworkwith40mmgaugebrickballastobtainedfrombreaking brick bats (brick bats supplied by the department free of cost) in proportion of 12:6:1 as in csi no. 5.01 includingcost of all labour, materials, t&p etc required for proper completion of work. 284 brickworkinfoundation&plinthwitholddismantled bricks(suppliedby departmentfreeofcost)andcoarsesand mortarin1:6includingsupply ofallothermaterials,labour,removingmortar&cleaningofold&usedbricks,t&p etc complete. 285 supply and filling brick bat in soak pit including all labour,material and t&petc complete. (for 01 soak pit) 286 supplying & fixing 24 gauge annodized aluminium sheet of approved qualityincludingcutting,wastageandfixingthesameoverthewooden door shutters with nails with all material, labour and t&p 287 providingandfixinginplaceafullheightstoragecabinet450mmdeep made with19 mm thick isi marked plyborad, allinterior surfaces to finishedwithpastingof0.8mmthickmicaandallexteriorsurfacestobe finshed with pasting of 1 mm thick mica of texture and colour as approved byengineerinchargeincludingalllabour,t&p,otheritemslike(butnot limitedto)fevicol,nailsscrews,higes,sliders,doorhandles,multipurpose lockofgodrejorequivalentrateetc.requiredforpropercompletionof works, to be measured interms of front area only. 288 providingandfixingfullheightpartitionwith02nos12mmthickisi marked ply board, all surfaces to finished withf 1 mm thick mica of texture andcolourasapprovedbyengineerinchargeandfixedinpolishedteak woodincludingalllabour,t&p,otheritemslike (butnot limitedto) fevicol, nailsscrews,hinges,sliders,doorhandles,multipurposelockofgodrejor equivalent rate etc. required for proper completion of works, to be measured interms of front area only 289 providingandfixing12mmthickframelesstoughenedglassdoorshutter ofapprovedbrandandmanufacture,includingprovidingandfixingtop& bottom pivot & double acting hydraulic floor spring type fixing arrangement ,doorhandle,lockandstopperetcandmakingnecessaryholesetc.for fixingrequireddoorfittings,allcompleteasperdirectionofengineer-in- charge 290 supply and fixing 6mm thick polycarbonate multiwall sheet ,fixing in position with j or u bolts 10 mm. dia with g.i. limpet & bitumen washers including supply of all materials, labour,wastage. and t&p etc. required for proper completion of the work. 291 providing (12x15) mm section groove in plasterincluding all material, labour andt&p etc. required for proper completion of the work.csi no.11.16 292 2.5 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cccsi no.12.26 293 4.0 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cc csi no. 12.28 294 dismantling ofdry b.o.e. floor and proper stacking of dismantled bricks as per direction of e/c. up to 60 m lead. 295 dismantling and re-laying of dry b.o.e. floor including cost of all labour and t&p required forproper completion of work.(labour rates only) 296 cleaning panes of glass with spirit of caustic soda including supply of all materials,labour and t&p etc.required for proper completion of the work. 297 cleaning of septic tank including disposal of waste out side the uppcl area as per direction of the engineer-in-charge including cost of all labour,t&p etc.required for proper completion of the work. 298 cleaning and opening of chocked w.c./ bath / kithchen pipe line including opening and refixing of chamber cover including washing etc. complete.(analysis based on nbo - 11 25.020. 299 s/laying chicken mesh of (20 mm.)hexagonal heavy quality over roofs of joints of roof as per direction of the engineer - in - charge. 300 cleaning of existing pipe line of different dia. ranging from 4 to 2 dia. including digging trenches and refilling, opening of pipes, cleaning of pipes, cutting, threading, if required fixing and including making good the road, wall etc as directed by the engineer i/c. 301 cleaning of existing water pipe line of different dia up to 2 dia including digging trenches and refilling,opening and cleaning of pipes,cutting,threading,if required fixing and including making good the road and wall etc. as directed by the engineer in charge. 302 cleaning of r.c.c. over head tank up to capacity of one lac. liters and chlorinating with bleaching power mixed to water as per direction of engineer - in - charge complete. 303 supply and mixing bleaching powder in over head tank as required or as directed by engineer - in - charge. 304 attending to petty maintenance service like plumbingservice,welder service, mansion service and carpenter servicerequired as below. (job attending by one no. plumber/welder/mason /carpenter with oneno. helper per hour or part of an hour.) 305 cleaning and sweeping of roof of residence as and when requiredincluding uprooting of rank vegetation and disposal of thegarbage upto 50 m. 306 providing and fixing of 150 mm dia pvc pipeof 6 kg/sqcmwith special such as tee, bend, socket, elbow etc including supply of all labour,material,t & p etc complete required for proper completion of work. 307 providing and laying 75 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 308 providing and laying 90 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 309 providing and laying 110 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 310 making arrangement for sweeping, cleaning of road, lanes in back of houses,collecting refuse of bushes & unwanted plants, vegetations etc. & disposal of all rubbish, materials industbins inside the colony area with engaging atleast one number of sweepers including all labour, t&p,etc.required for completion of work as directed by e/i. 311 making arrangement for sweeping, cleaning of ee,ecd(d), georgetown ,prayagraj office rooms, cleaning of dustbin, toilets , dusting of almirahs,tables etc. using phenyle,dusting cloth etc. and disposal of waste outside office premise in municipal dustbinswith engaging sufficient number ofsweepersincluding all labour, t&p,etc.required for completion of work as directed by e/i.(nsi)(consumable items as phenyle,dusting cloth ,brooms etc shall be provided by the department free of cost.) 312 cleaning of main drain or width more than 300mm including disposal of waste refuses studge out side the boards ara including washing and cleaning by clean water completely as per direction of the e/i. including cost of all labour, t&p etc. required for completion of the work. (csino.20.14) 313 cleaning of main drain or width less than 300mm including disposal of waste refuses studge out side the boards ara including washing and cleaning by clean water completely as per direction of the e/i. including cost of all labour, t&p etc. required for completion of the work. (csino.20.15) nsi sl. no.63 314 operation of tube well daily by a suitable experienced operator continously or in different intervals as per program as per program fixed by engineer-in-charge including opening and closing of valves,changing of fuse wire etc. as requrird for proper running of tube well. (nsi) 315 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc as required..group c 316 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet 317 supplying and fixing of 20 mm of medium class pvc conduit along with accessories in surface/recess including junction box, cutting the wall and making good the same in case of recessed conduit as required. 318 supplying and fixing of 25 mm of medium class pvc conduit along with accessories in surface/recess including junction box,cutting the wall and making good the same in case of recessed conduit as required. 319 wiring for circuit/ submain wiring with 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 320 wiring for circuit/ submain wiring with 2 x 4 sq. mm + 1 x 4 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 321 wiring for circuit/ submain wiring with2 x 6 sq. mm + 1 x 6 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 322 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required . 323 providing and laying earth connection from earth electrode with 6 swg dia g.i. wire in 15 mm dia g.i. pipe from earth electrode including connection with g.i. thimble excavation and re-filling as required. 324 supplying and fixing 5 amps to 32 amps rating,single pole, 240/415 volts, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 325 supplying and fixing 63 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 326 supplying and fixing 40 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 327 supplying and fixing 4 way (4 + 12), double door, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without mcb/rccb/isolator) 328 supplying and fixing of 4 way (4 + 12), double door surface/ recess mounting, vertical type, 415 volts, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs (but without mcbs and incomer ) as required . (note : vertical type mcb tpdb is normally used where 3 phase outlets are required.) 329 wiring for light/ power plug with 2x4 sq. mm frls pvc insulated copper conductor single core cable in surface/ recessed medium class pvc conduit along with 1 no 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. 330 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module (75mmx75mm) 331 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required.3 module (100mmx75mm) 332 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 4 module (125mmx75mm) 333 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 6 module (200mmx75mm) 334 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 8 module (125mmx125mm) 335 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 12 module (200mmx150mm) 336 supplying and drawing following 3 x 2.5 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required. 337 supplying and drawing following 3 x 4 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required.(dsr e&m 2022 1.17.21) 338 rewinding of burnt ceiling fan with approved copper wire including cost of all materials, labour and t&p etc. complete (burnt wirewill not be taken back.) 339 greasing of ceiling fan after cleaning the bearing and shaft withoil / petrol and its testing. 340 supply and fixing of led tube light batten fitting suitable for up to 1 x 22 watt led tube light on surface complete in all respect.(csi no. 28.41) 341 supply of 9 watt led bulb make philips, syska, bajaj etc or its equivalent as directed by e/i. 342 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current (bldc) motor, class of insulation: b, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (cm/m/w) minimum 6.00, air delivery minimum 210 cum/min, 350 rpm (tolerance as per is: 374-2019), thd less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than 2 mega ohm, suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required.(dsr e&m 2022 19.1) 343 supply and fixing of 5 blade exhaust fan ventile air dx 225 mm of havellsor equivalent make including all material, t&p etc required for proper completion of work as approved by engineer in charge.(csi no. 28.38) 344 supply and fixing of 3 blade wall fan ofhavells platina 400 mm or equivalent including all material, t&petc required for proper completion of work as approved by engineer in charge.(csi no. 28.37)

Central Government/Public Sector

TRN :49068676 | 28 May, 2025

Tender Value : 20.00 Lacs

Bikaner - Rajasthan

Tender for tender for welcome maintenance to officers md accommodation at af station nal; 1 demolition of brick or stone masonary built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed. 2 material and labour brick work with sub class -b bricks old size, straight or curved on plan exc 6m mean radiusbuilt in cm 1:6. complete all as specified & directed. 3 all as per serial item no. 2.00 (here in before) but as in half brick thick walls built in cement mortar 1:4. 4 taking down chawkhat or frame with shutter (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed. 5 taking down chawkhat or frame with shutter (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.0 sqm each complete all as specified and directed. 6 taking down door shutter of any description exc 1.00 sqm but n. exc. 2.00 sqm each complete all as specified and directed. 7 taking down wooden shutters of any description exc 1 sqm but n.exc 2 sqm each from chowkhat and re-fixing in same opening after re-securing or easening and adjusting including repair of hinge as required complete all as specified and directed. 8 s&f solid pvc door frame of size 50mm x 47mm made out 5mm both side prelam pvc sheet used instead of plain colour pvc sheet & edges will be painted to match with prelam sheet re-inforced with ms square tube complete all as specified and directed. 9 m&l for factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of ms tubes 40mm x 20 mm for top and bottom rails ms frame shall be covered with heat moulded prelam pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour pvc sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottam rail both side prelam pvc sheet used instead of plain colour pvc sheet. stile and rails feathered at edges paneling of prelam solid pvc sheets 10mm thick to be filted in msframe 40 x 20 mm welded, sealed to the stiles and rails with suitable pvc sheet beading, and jointed together with the solvent cement complete all as specified and directed. 10 s&f 1.25 mm thick pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c-0 using 12.5 mm graded stone aggregate complete all as specified and directed. 11 s&f 1.25 mm thick pressed steel frames of size 105mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c-0 using 12.5 mm graded stone aggregate complete all as specified and directed. 12 s&f 35 mm thick 2nd class hard wood factory made plain framed, pannelled shutter (any number of panels) with panel of timber flat on both sides (feather edged) or of 12mm thick bwp commercial plywood with commercial face veneers, supplied and fitted complete all as specified and directed. 13 supply and fixing glazed and gauged skeleton factory made shutters35mm thick, 2nd class hard wood hollockopen rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cutand mitred beads for securing glass etcincl priming coat. the size of member of shutters as spfd in ssr part-1 section 8 clause 8.20 (b) incl kiln seasoned and chemically pressure treated, complete all as specified & directed. 14 s&f30mm factory made thick flush shutters, solid core construction,with particle board coreand plywood face panels,commercial type on both face is covered with decorative face veneer with lipping/frame to match sides includeforthe provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specified and directed. 15 s&f butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, 100mm size, isi marked, complete all as specified & directed. 16 supply and fixing200mm size aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. 17 supply and fixing 150mm sizeextruded aluminium alloy handles, fabricated type, anodised aluminium handles, complete all as specified and directed. 18 supply and fixing 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. 19 supply& fixingas in repairfloor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed to door shutters,complete all as specified and directed. 20 supply and fixing galvanised stainless steel wire cloth 0.45mm nominal dia of wire and width of aperture 1.40mm and fixed with tinned tacks or galvanised wire stapples/ screws in metal surrounds as required fixedcomplete all as specified and directed. 21 all as per description of serial item no. 20 here in before but as in repair 22 hacking out old broken glass of any thickness/size of any description from wooden frames/metal frame glazed with putty or fixed with beads all as specified. 23 supply and fixing 3mm thick sheet glass, ordinaly quality and glazing with oil putty or secured with spring clips in metal surrounds as required in square n exc 0.5 sqm in each pane , complete all as specified and directed. 24 all as per description of serial item 23 here in before but figured glass, pin head type. 25 s&f as in repairs door closer hydraulically regulated cast iron body, designation no 2, universal type, suitable for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg,complete all as specified and directed. 26 s&f as in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller pleat complete all as specified and directed. 27 s&f in repair stainless steel (grade 305) curtain rods 25mm dia 0.80mm wall thickness mild steel chromium plated incl supporting brackets complete all as specified and directed. 28 s&f in repair stainless steel (grade 305) ornamental type brackets (open ends) suitable for curtain rods of 25mm dia all as specified and directed. 29 s&f in repair stainless steel (grade 305) brackets (dead ends) suitable for curtain rods of 25mm dia all as specified and directed. 30 demolition of cement concrete in any positionand removing the rubbish outside mod land complete all as specified anddirected. 31 m&l for pcc (1:3:6) type c-2, using 40mm graded stone aggregate as in plinth protection 75mm thick laid in bays including all necessary form work, finishing exposed edges fair and providing 10 mm wide joints throughout the thickness of plinth protections duly filled with matic filling(one part of hot bitumen 85/25 and three parts of sand)and surfaces finished even & smooth without using extra cement complete all as specified . 32 m&l 25mm thick pcc 1:2:4 type b-0(using 12.5mm graded stone aggregate)as in sub base of floor surface finished even rough to receive floor topping complete all as specified and directed. 33 dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed. 34 m&l for granite (of any type)slab 18-20 mm thick machine cut ,bedded and jointed with gray cement slurry and pointed with white cement as in floors/ cooking plateform, with admixiture of pigment to match the shade of granite stone including grindingand polishing complete over and including20 mm thick screed bed in cm 1:6 complete all as specified . 35 m&l for granite (of any type)slab 18-20 mm thick machine cut , jointed with gray cement slurry and pointed with white cement as in vertical surfaces / dado / skirtingwith admixiture of pigment to match the shade of granite stone indluding grindingand polishing complete over and including10 mm thick backing coat in cm 1:4 complete all as specified . 36 m& l green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, including grinding and polishing providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete complete complete all as specified and directed. 37 dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified. note:-the demolished material should be disposed off out side the mod land. the contractor shall quote his rates considering the above element 38 material and labour for glazed ceramic coloured tiles 7 to 8mm thick (square/rectangular )in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm thick set & jointed in neat gray cement slurry and pointed with coloured cement to match,the sahde of tiles laid over and including 10mm thick rendering in cm 1:4 complete all as specified and directed. 39 material and labour non-skid, ceramic coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,as in floors, set and jointed ingray cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 40 material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,as in floors, set and jointed ingray cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 41 material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed ingray cement slurry and pointed in white or coloured cement to matchthe shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in cm (1:4) complete all as specified and directed. 42 m&l for vitrified light shade ceramictiles9 to 10 mm thick polished,area of each tile exc 0.18 sqm andn exceeding 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cm 1:6 complete all as directed by engr-in-charge. 43 all as per ser item no.42 (here in before) but as in skirting laid over and including 10mm cement backing in cm 1:4. 44 material and labour for repairing of soffits of slabs/chajja, facia and similar works by dismantling of loose/ disintegrated portion of rcc upto 7.5 mtr heightand in any sitution, including provn of support,formwork and welding of reinforcement and fixing in position and with provision of weld mesh, applying dubbing 1st coat of 20 to 25mm thick in cm 1:3 finished rough and finishing coat of 10mm thick in cm (1:3) finished even and smooth without using extra cementover and including cement slurry @ 3 kg/sqm, finished even and smooth to desired shapeand applyingtwo coats of weather proof exterior emulsion paint over a coat of arylic resistant primer to match with existing surfaces complete all as specified and directed.(weld mesh measured and paid sepatrtely)note:-(i) unit rate of this item includes the cost of scaffolding, formwork etc. and nothing extra shall be paid on account of variation in height.(ii) for payment purpose, the area of finished plaster in 2nd coat shall be considered. 45 material and labour for hard drawn steel wire fabric (weld mesh) of weight not less than 3 kg/ sqm and not exc 4 kg/ sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt including necessary fixing arrangements etc complete all as specified and directed. 46 taking down cementplaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down down with water etc complete all as specified and directed. note:- the demolished materials should be disposed off at a site as described by the eng-in-charge. the contractor shall quote his rates considering the above element. 47 m&l for rendering 10 mm thick on ceiling (brick or concrete surfaces)in cement mortar 1:4 and surface finished even and smooth without using extra cement complete all as specified and directed. 48 m&l for rendering 15mm thick on brick or concrete surfaces in cement mortar 1:6, finishing surfaces even and smooth without using extra cement complete all as specified and directed. 49 m&l forrendering 15mm thick on brick or concrete surfaces other than fair face of brick work in cement mortar 1:4, finishing surfaces even and smooth without using extra cement complete all as specified and directed. 50 m&l for applying three coats of white wash on newly plasteredsurfaces of ceiling including preparation of surfaces complete all as specifed and directed. 51 m&l for preparation of newly plastered or unplastered surfaces of walls and applying two coats of exterior acrylic emulsion in any pattern (approved by ge), paint over and including a coat of exterior primer complete all as specified and directed. 52 m&l for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted over and including a coat of primer complete all as specified and directed. 53 material & labour for prepapration of new or previously untreated surfaces of wood or wood based materials of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over & including a coat of pink primer comlplete all as specified and directed. 54 material & labour for prepapration of new or previously untreated steel or iron surfaces of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over & including a coat of red oxide primer comlplete all as specified and directed. 55 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified. 56 material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling etc. incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified. 57 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of oil bound distemper complete all as specified & directed. 58 material and labour for comple removal ofold decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying two coats of oil bound distemper complete all as specified & directed. 59 m&l for complete removal of existing treatment on walls and applying two coat ofoil bound distempe paint interior gradeover & including a coat of alkali resistant priming paint over 7 including two layer of birla wall putty (min thickness 3mm) incl filling in craks etc to achieve a uniformsmooth finish incl preparationof surfaces complete all as specified & directed . 60 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of plastic emulsion complete all as specified & directed. 61 m&l for preparation of old painted surface of wood and wood based materials of any description not otherwise described over 10 cm. width or girthshallapplying one coat of synthetic enamel painting overthe wooden surfaces all as specified & directed. 62 m&l for preparation of old painted surfaces of steel and iron work of any description exc 10 cm width or girth applying one coat of synthetic enamel paint on steel surface all as specified. 63 taking up or down 15 mm bore steel tubing & connections including clearing for refixing or removal to store complete all as specified and directed. 64 all as perserial item 63 here in before but 20m bore tubes 65 supply and fixing15mm bore tubes “medium grade”, galvanized, with and including all fittings and fixed completetowalls and ceilings or laid in floors,complete all as specified and directed. 66 all as per serial item 65 here in before but 20m bore tubes 67 s&f as in repair pillar taps long body fancy type quarter turn with capasten head chromium plated screwed down high pressure with without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. 68 supply and fixing as in repairs bib cock quarter turn cast copper alloy chromium plated, fancy type, long body screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 69 s & f as in repairs two way angle cock quarter turn cast copper alloy 15 mm bore chromiun plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. 70 s & f as in repairs angle cock quarter turn cast copper alloy 15 mm bore chromiun plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. 71 supply and fixing as in repair central hole basin mixer long swang nack, without poup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 72 supply and fixing as in repair central hole sink mixer long body swang nech for mixing hot & cold water, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 73 s&f as in repair brass cp wall mixer 3-in-1 system with provision for both hand shower and over head shower complete with 115mm long bend pipe, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. 74 s&f as in repair brass cp wall mixer 2-in-1 system with provision for over head shower complete with 115mm long bend pipe on upper side, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. 75 supply & fixingas in repair chromium platedshower rose with or without swivel joints 125mm dia including fixing to steel pipe,complete all as specified and directed. 76 supply& fixing as in repair toiletpaper holder of brass chromium plated, complete all as specified and directed. 77 supply& fixing as in repairs pvc (ptmt) float valve,high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe,complete all as specified and directed. 78 supply& fixing as in repairs pvc waste down pipeof 32/40 mm bore for basin, complete all as specified and as directed. 79 supply and fixing as in repairs 15mm dia pvc connection of length 450 mm, with ptmt nut, complete all as specified and directed. 80 supply and fixing as in repairs faucet health (hand jet) 15mm bore cast copper alloy, chromium plated with flexible chromium plated connection pipe 1.5 mtr length, with fittings, complete all as specified and directed. 81 supply& fixingas in repairs wash hand basin, vitreous china, white, decorative type, flat or angleback, size 580mm x 450mm inclusive ofwaste pipe and brass coupling and including cutting for and pinning in ends of brackets or erecting stand and inclusive of cost of brackets complete all as specified and directed. 82 s&f as in repair vitreous china pedastal pattern, wc incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete all as specified and directed. 83 s&f in repair rimless single piece wc with uf soft close slim seat cover, hinges, fixing accessories set , incl cisternfittings, size 385x720x715mm complete all as specified directed by engr-in-charge. make: jaguar/cera/hindware 84 supply and fixing as in repair pvc valve less syphonic action type flushing cistern low level white with pvc in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including pvc connection and 32mm dia pvc long bend for squat pattern etc, set with concrete and making good to floor including taking down existing, fixed as in repairs complete all as specified & directed. 85 s&f as in repair ptmt seat cover white colour for padastal pattern,incl connection nut & bolts, etc. complete all as specified and directed. 86 s&f as in repair sinks with drain board made of stainless steel sink of 1mm thick sheet, kitchen or laboratory with plug washer and waste pipe incl bedding in cement mortar 1:6 on to draft wall of including fixing cantilever brackets and connecting unions overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed as in repairs complete all as specified. 87 supply& fixingas in repair pvc bath cabinet, size 622mm x 422mm, comprising of lookingglass, space for bath soaps, shampoo, tooth brush and paste, hand towel rail, complete all as specified and directed. 88 supply and fixing in repair stainless steel towel rack 600mm long with lower hangers incl 3 hooks complete all as specified and directed. 89 supply and fixing in repair brass chromium plated tubular towel rail 20mm dia d type 60 cm long between flanges complete all as specified and directed. 90 supply and fixing as in repair soap dish chromium plated of size 100 x 100 mm any type, fixed with chromium plated brass screwscomplete all as specified and directed. 91 s & f as in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed. 92 s&f as in repairs corner glass shelf with cp brackets (3 pcs set having size 8,10 & 12)complete all as specified and directed. 93 demolition and breaking up drain pipes 110/75 mm bore (salt glazed ware, ac or reinforced concrete) set in cement mortar complete all as specified and directed. 94 s&f 110mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to wall &laid in trenches or in floors,including clamps as required, complete all as specified and directed. 95 s&f 75mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to wall &laid in trenches or in floors,including clamps as required, complete all as specified and directed. 96 s&f in repair 75mm dia pvc (swr) floor trap plain with cp grating including jointing with solvant cement incl necessary pcc & form work as required complete all as specified and directed. 97 s&f 75mm dia pvc (swr) bends with rubber ring joints fixed as required with oval access door complete all as specified and directed. 98 s&f 110mm dia pvc (swr) bends with rubber ring joints fixed as required with oval access door complete all as specified and directed. 99 s & f 110mm bore pvcswr junction single (single t) with access door complete all as specified and directed 100 s&f in repairs stainless steel plate rack of size 78cmx91cmx25cm made out of 0.80 mm thick of stainless steel sheet , fixed in wall with rawl plugs and screws complete all as specified and directed. 101 dismantling boarding, any description any size , fixed in any position with screws complete all as specified . 102 m& l for 18 mm thick pvc board celuka ply of density 600kg/cum one side prelam/rigid laminated (colour/shade as approved by engr-in-charge) and other side plain white colour to make kitchen cabinet shutters /shelves/partitions and incl all required brackets ss screws etc, approved by engr-in-charge. 103 m& l for 18 mm thick pvc board celuka ply of density 600kg/cum both sidesplain white colour to make kitchen cabinet shutters/shelves/partitions and all required brackets ss screws etc, approved by engr-in-charge. 104 s&fin repair auto closes clip on cabinet hinges (regular) for kitchen cabinet shutters note : each pair means one piece fixed on openable shutter and other piece fixed on fixed portion. 105 s&fin repair stainless steel (ss 304) handles 100 mm size for kitchen cabinet shutters. 106 s&fin repair ball bearing drawer channel telescopic type (500mm) full extention load of load bearing capacity 45 kg.note : each pair means 2 nos of telescopic channel, one piece fixed on left side and another piece fixed on right side. 107 s&f rab door seal bottom brush duststopper with aluminium plate nylone brush of selected colour for fit each complete all as specified and directed. note : the sample of item shall be approved by ge before placing at site 108 supply and fixing powder coated aluminium (minimum thickness of powder coating 50micron) work for frames of doors, windows,ventilators and partitions (fixedportions) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge note:-for payment purpose weight of aluminium section will only be measured 109 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings such as hinges,handle,tower bolt,sliding boltshall be paid for separately) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws,rollers & dust proof brush for sliding door / windowcomplete all as per architectural drawings and the directions of engineer-in-charge note:-for payment purpose weight of aluminium section will only be measured 110 s & f as aluminium grill of size, 85mm x 85mm hexagonal shaped mesh, fixed to aluminium frame work with u clip of size 15mmx12mm & fastners complete all as specified and directed. 111 s & f4.80 mm thick sheet glass ofordinary quality plain / tintedand glazing with rubber beads, clips etc complete all as specified and directed. 112 s & f 3 mm thickhigh quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed. 113 s & f double action floor door spring hydraulically regulated made up minimum1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, with governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified 114 s&f conceled lock (push to unlock) for sliding window made with zinc body, aluminium hook and anti rust material with power coated metallic finish of approved colour having size100mm x 24 mm incl necessary cutting for fixing all as specified and directed.

Local Bodies

TRN :49069168 | 18 May, 2025

Tender Value : 70.00 Lacs

Phalodi - Rajasthan

Tender for tender for supply of construction material in gram panchayat phalodi in panchayat samiti khandar under mnrega and rd and various scheme for the year 2025-26 , 1 particulars 2 ghadla / kankar / jhajhra 3 mortar - soil / mud masala 4 lime - lime from brick kiln for masonry work 5 cement 6 ppc 7 white cement 8 fine agreegate 9 sand / gravel 10 gravel - local / local 11 rakhi (fly ash) 12 surkhi 13 stone dust (stone dust, used in masonry work) 14 ballast of stone / brick (for other than road work) 15 stone 40 mm measured (grit broken by hand) (wides cut 1/11) 16 stone 40 mm grit (broken by crusher) (wides cut 1/11) 17 stone 20 mm grit (broken by crusher) ) 18 stone 12 /10 /6 mm grit (broken by crusher) 19 brick ballast 20 road works material (5 km. lead including) 21 63-40 mm (broken by crusher) (wides cut 1/11) 22 63-40 mm (broken by hand) (wides cut 1/11) 23 90-45 mm (broken by hand) (wides cut 1/11) 24 kaveri rubbish (wides cut 1/6) 25 gravel (wides cut 1/6) 26 kankar (wides cut 1/6) 27 binding material ( pi 4-6) (wides cut 1/6) 28 brick (22.5 x 11 x 7.50 cm) 29 first class (i class) 30 second class (ii class) 31 soiling/kharanja/masonry stone 32 masonry beradda (rr) 33 masonry radda (cr) 34 kharanja soling (for flooring work upto 15 cm height) 35 kharanja soling (for road kharanja work upto 23 cm height) 36 jodhpuri type stone strip/champ/katli pieces (length 2-3, width 10-12, pearl 2.5-3.5) 37 stone arch (flaky material)(3-4 thick & length & width1-2) 38 sandstone (dpc, sill, coping, lintel, tand, almirah, etc) 39 upto 25 mm thickness 40 25 - upto 40 mm thickness 41 40- 50 mm thickness 42 50 - 75 mm thickness 43 75 - 100 mm thickness 44 100 -150 mm thickness 45 flooring / strip painting katla stone 46 flooring katla upto 35 mm thick , min. 3 sqft or more area 47 katla for strip painting 60 -75 mm thickness , min. 3sqft or more area 48 unpolished rough kota stone 49 upto 900 sq.cm 50 upto 901 to 2300 sq.cm 51 more than 2300 sq.cm 52 polished kota stone (one side polished) 53 upto 900 sq.cm 54 upto 901 to 2300 sq.cm 55 more than 2300 sq.cm 56 marble stone (makrana adanga 20mm thick) 57 upto 900 sq.cm 58 upto 901 to 2300 sq.cm 59 more than 2300 sq.cm 60 marble chips 61 marble powder 62 marble stone (rajnagar ii quality/local 20mm thick) 63 upto 900 sq.cm 64 upto 901 to 2300 sq.cm 65 more than 2300 sq. cm 66 single petam size 100 x 75 mm 68 double petam size 125 x 75 mm 69 stone slab 70 up to 1.5 m length , minimum 40 mm thick 71 1.5 m to 2.40 m length, minimum 50 mm thick 72 2.4 m to 3.0 m length , minimum 6 5 mm thick 73 above 3.0 m length, minimum 75 mmthick 74 precast tiles / blocks 75 glazed size 30 x 45 cm 76 mosaic size - 40 mm thick 77 vitrified size- 60 x 60 cm 78 interlock tiles / brick / block for road work 79 cement interlocking block m - 30 grade , 60 mm thick 80 cement interlocking block m - 30 grade ,80 mm thick 81 cement interlocking block m - 30 grade , 100 mm thick 82 fr pvc insulated copper conductor single core cable isi marked 83 1.50 sq.mm. 84 2.50 sq. mm. 85 0.50 sq mm 86 1.00 sq. mm. 87 4.00 sq. mm. 88 6.00 sq. mm. 89 local wood with fittings (for doors, windows and furniture) 90 mango 91 babul 92 others 93 factory made doors (30mm thick, solid core single leaf) 94 structural steel 95 iron (tor steel fe 415 / 500 for reinforcement) 96 winding wire 18 yards 97 iron girders 98 conical iron / square bar / strip / angle iron) 99 barbed iron wire (size 12 guage wire and 12 guage strad / 12 guage wire and 14 guage strad / 14 guage 100 mesh 101 iron mesh (24 gauge, 14 mesh) 102 cement concrete mesh akash patal 40 mm thick 103 glass 104 3 mm thick glass 105 colour - paint 106 enamel paint 107 decolorant (water bound) 108 lime - for painting (aras / kali) 109 primer (for iron / wood) 110 petroleum products 111 diesel hsd 112 mobil oil 113 bitumen shalitex board (25 mm thick) 114 plain sheet 115 g.i. sheet 22 gauge (0.80 mm) 116 g.i. sheet 24 gauge (0.63 mm) 117 m.s. sheet 22 gauge (0.80 mm) 118 m.s. sheet 24 gauge (0.63 mm) 119 corrugated sheet 120 g.i. sheet 1 mm thick 121 gi sheet 22 gauge (0.80 mm ) 122 aswests cement sheet 6 mm ( 2.5 / 2.75 x 1m) 123 other sheets 124 pvc sheet 1 mm thick ( coloured / plain ) 125 green yellow literof expo sheet (183 x 90 ) 126 pipes 127 gi 15 mm dia ( b class) 128 gi 20 mm dia ( b class) 129 gi 25 mm dia ( b class) 130 ac 75 mm dia 131 ac 100 mm dia 132 pvc 90 mm diameter (with ring) 133 p.v.c. 110 mm. diameter (with ring) 134 p.v.c. 140 mm. diameter (with ring) 135 p.v.c. 110 mm. (2.5 kg / sq. cm) with coupler 136 sanitary 137 indian w.c. 138 orissa w.c. 139 european w.c. 140 foot rest 141 porcelain urinal 430 * 350 * 300 mm with coupler, bracket and p.v.c. waste pipe 142 wash - basin 450 * 300 mm with coupler, bracket and p.v.c. waste pipe 143 stone bore (s.w.) pipe 100 mm dia, 0.6m long, 144 c.p. pillar cock (dia 15 mm ) (is mark ) 145 c.p. bibb cock (dia 15 mm ) (is mark ) 146 125 mm dia cp gratting 147 r.c.c. np3 hume pipe with collar 148 1200 mm dia 149 1000 mm dia 150 750 mm dia 151 600 mm dia 152 450 mm dia 153 300 mm dia 154 steel conduit isi marked 155 20 mm dia 156 25 mm dia 157 charcoal 158 p.v.c. water tank with cover (conforming to is : 12701 - 1989) 159 13/0.20 mm twin car pvc blank with flange flexible copper cable 160 steel fasteners 6 mm x 75 mm 161 pvc conduit isi marked 162 25 mm diameter 163 20 mm diameter 164 junction box 165 20 mm two way 166 20 mm one way 167 25 mm two way 168 20 mm one way(pvc) 169 module gi box 170 for 3 modules 171 for 2 modules 172 module base cover & plate 173 for 2 modules 174 for 3 module 175 module switch one way, isi mrked 176 sp 15 /16 ampere 177 sp 5 /6 ampere 178 modular socket outlet, isi mrked 179 3 pin 5 /6 ampere 180 6 pin 15 /16 ampere 181 mcb db 182 2+2way, spn, single door 183 2+4way, spn, single door 184 2+6way, spn, single door 185 gi pipe (medium grade) 186 15.00 mm dia 187 40.00 mm dia 188 copper wire 8 swg (4.00 mm dia) (0.117 kg/m) 189 ci/ms cover plate, attached to frame of locking arrangement 190 approved equipment hire rate (with pol & driver) 191 diesel road roller 8 to 10 ton 192 sheep foot roller 193 truck 9 ton 194 tractor (25 - 40 hp) 195 tractor with trolley 196 tractor water tanker capacity 4000 liter water 197 cement concrete mixer 5 - 7 cubic feet 198 pumping set 15 h. p. 199 niddle / plate vibrator with operator 200 camel cartrid / bell cartrid with driver 201 grinding machine with operator (large, motor driven) 202 compressor 203 hydrolic excavator / jcb (bucket capcity 0.4 cum) 204 dumper 205 scraper 206 shuttering of wooden frost, with beings and other materials, added at site, removed after the specified period 207 shuttering of ply, with beings and other materials, added at site, removed after the specified period 208 shuttering of iron plate, with beings and other materials, added at site, removed after the specified period 209 water and pumping expenses (filling) 210 grinding machine with operator (small, hand operated) 211 iron frame for well (diameter 3 m, height 75 cm) with tp, to be installed at site, removed after stipulated period 212 cultivator side board etc.

Local Bodies

TRN :49028253 | 15 May, 2025

Tender Value : 50.00 Lacs

Barmer - Rajasthan

Tender for supply of building material and equipment in gp barasan ps gudamalani-ghadla/kankar/jhajhra 2 mortar-soil/mud masala 3 lime from kali kiln for masonry work 4 cement 5 p.p.c. 6 white cement 7 fine aggregate 8 sand/gravel 9 fly ash 10 surkhi 11 stone dust (in masonry work) 12 ballast of stone/brick (for other than road work) 13 stone 40mm measured (grit broken by hand) (cut voids 1/11) 14 stone 40mm grit (broken by crusher) (cut voids 1/11) 15 stone 20mm grit (broken by crusher) 16 stone 12/10/6mm grit (broken by crusher) 17 brick ballast 18 material for road work (including 5 km lead) 19 63-40 mm stone crushed stone gravel (cut voids 1/11) 20 63-40 mm hand broken stone aggregate(cut voids 1/11) 21 90-45 mm. hand broken stone aggregate(cut voids 1/11) 22 quarry rubbish(cut voids 1/6) 23 gravel(cut voids 1/6) 24 kankar(cut voids 1/6) 25 binding material (pi 4-6)(cut voids 1/6) 26 brick (22.5 x 11 x 7.50 cm) 27 first class (i st class) 28 second class (ii class) 29 soling/ kharanja/ masonry stone 30 masonry beradda (rr) 31 masonry radda (cr) 32 kharanja soling (for flooring work upto 15cm height) 33 kharanja soling (for road/ kharanja work upto 23cm height) 34 jodhpuri type stone strips/arches/cuts (length 2-3, width 10-12,thickness 2.5-3.5) 35 stone chips (flaky material)(3-4 thick & length and width 1-2) 36 sandstone(dpc,sill,coping,lintel,tand,almirha etc) 37 upto 25mm thickness 38 upto 25-40mm thickness 39 upto 40-50mm thickness 40 upto 50-75mm thickness 41 upto 75-100mm thickness 42 upto 100-150mm thickness 43 flooring / patti pattan katla stone 44 flooring katla upto 35mm thick, min. 3 sqft or more area 45 patti pattan katla 60-75mm thickness, min. 3 sqft or more area 46 unpolished rough kota stone 47 900 sq. cm 48 upto 901 to 2300 sq. cm. 49 above 2300 sq. cm. 50 polished kota stone(one side polished) 51 upto 900 sq. cm. 52 upto 901 to 2300 sq. cm. 53 above 2300 sq. cm. 54 marble stone(makrana adanga 20mm thick) 55 upto 900 sq. cm. 56 upto 901 to 2300 sq. cm. 57 above 2300 sq. cm. 58 marble chips 59 marble powder 60 marble stone(rajnagar ii quality/local 20mm thick) 61 upto 900 sq. cm. 62 upto 901 to 2300 sq. cm. 63 above 2300 sq. cm. 64 stone frame 65 single paitaam size 100 x 75 mm. 66 double pattam size 125 x 75 mm. 67 stone plates 68 up to 1.5 m length, minimum 40mm thick 69 1.5 m to 2.40 m length, minimum 50mm thick 70 2.4 m to 3.0 m length, minimum 65mm thick 71 above 3.0 m length, minimum 75mm thick 73 glazed size-30x45 cm 74 mosaic size-40mm thick 75 vitrified size-60x60 cm 76 interlock tiles/brick/block for road work 77 cement interlocking block m-30grade, 60mm thick 78 cement interlocking block m-30grade, 80mm thick 79 cement interlocking block m-30grade, 100mm thick 80 fr pvc insulated copper conductor single core cable isi marked 81 1.50 sq. mm. 82 2.50 sq. mm. 83 0.50 sq. mm. 84 1.00 sq. mm. 85 4.00 sq. mm. 86 6.00 sq. mm. 87 local wood with fittings (for doors, windows and furniture) 88 mango 89 acacia 90 others 91 factory made doors (30mm thick, solid core single leaf) 92 structural steel 93 iron (tor steel fe 415/500 for reinforcement) 94 winding wire 18 gauge 95 iron girders 96 conical iron/ square bars/ leaf/ angle iron 97 barbed iron wire (size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage 98 mesh 99 iron mesh (24 gauge, 14 mesh) 100 cement concrete mesh akash patal 40mm thick 101 glass 102 3mm thick glass 103 colour paint 104 enamel paint 105 distemper (water bound) 106 lime - for whitewashing (aras / kali) 107 primer (for iron / wood) 108 petroleum products 109 diesel hsd 110 movil oil 111 bitumen shalitex board (25 mm thick) 112 plain sheet 113 g.i. sheet 22 gauge (0.80 mm) 114 g.i. sheet 24 gauge (0.63 mm) 115 m.s. sheet 22 gauge (0.80 mm) 116 m.s. sheet 24 gauge (0.63 mm) 117 corrugated sheet 118 g.i. sheet 1 mm thick 119 gi sheet 22 gauge(0.80 m.m.) 120 asbestos cement sheet 6mm(2.5/2.75x1m) 121 other sheets 122 pvc sheet 1mm thick (coloured/plain) 123 green yellow literof expo sheet(183x90) 124 pipes 125 gi 15mm diameter(b class) 126 gi 20mm diameter(b class) 127 gi 25mm diameter(b class) 128 a.c. 75mm diameter 129 a.c. 100mm diameter 130 p.v.c. 90mm diameter diameter(with ring) 131 pvc 110 mm. diameter(with ring) 132 pvc 140 mm. diameter(with ring) 133 pvc 110 mm.(2.5kg/sq.cm) with coupler 134 sanitary 135 indian w.c. 136 orrisa w.c. 137 european w.c. 138 foot rest 139 porcelain urinal 430350300 mm with coupler, bracket and pvc waste pipe 140 wash-basin 450*300 mm with coupler, bracket and pvc waste pipe 141 stone beam (s.w.) pipe 100 mm. diameter, 0.6 m. long 142 c.p. pillar cock (dia 15 mm) (is mark) 143 c.p. bib cock (dia 15 mm) (is mark) 144 c.p. grating of 125 mm. diameter 145 r.c.c. np3 hum pipe with collar 146 1200 mm dia 147 1000mm dia 148 750mm dia 149 600mm dia 150 450mm dia 151 300mm dia 152 steel conduit isi marked 153 20 mm. diameter 154 25 mm dia 155 charcoal 156 p.v.c. water tank with cover (conforming to is:12701-1989) 157 13/0.20 mm twin core pvc sheathed, flat flexible copper cable 158 steel fasteners 6 mm x 75 mm 159 pvc conduit isi marked 160 25 mm diameter 161 20 mm diameter 162 junction box 163 20 mm two way 164 20 mm one way 165 25 mm two way 166 20 mm one way (pvc) 167 module gi box 168 for 3 modules 169 for 2 modules 170 module base & cover plate 171 for 2 modules 172 3 for module 173 modular switch one way, isi marked 174 sp 15/16 ampere 175 sp 5/6 ampere 176 modular socket outlet, isi marked 177 3 pin 5/6 ampere 178 6 pin 15/16 ampere 179 mcb db 180 2+ 2 way, spn, single door 181 2+4 way, spn, single door 182 2+6 way, spn, single door 183 gi pipe (medium grade) 184 15.00 mm diameter 185 40.00 mm diameter 186 copper wire 8 swg (4.00 mm dia.) (0.117 kg/m) 187 ci/ms cover plate, frame with locking arrangement attached to 188 diesel road roller 8 to 10 ton 189 truck 9 ton 190 tractor (25-40 hp) 191 tractor trolley 192 tractor water tanker capacity 4000 liter water 193 cement concrete mixer 5-7 cubic feet 194 pumping set 15 h.p . 195 niddle/plate vibrator with operator 196 camel cart/bullock cart with driver 197 grinding machine with operator (big, motor driven) 198 compressor 199 hydraulic excavater/jcb ( bucket capacity 0.4 cum) 200 dumper 201 scraper 202 shuttering of wooden plank, with installing tp along with bat and other materials on site, removing it after the prescribed period 203 installing shuttering ply along with bat and other materials on tp site, removing it after the prescribed period 204 shuttering iron plate along with bat and other materials along with tp installation at site, removal after specified period 205 water and pumping charges (filling) 206 grinding machine with operator (small, hand operated) 207 installing iron form for well (diameter 3m, height 75cm) along with tp at site, removing after specified period 208 cultivator

1

Related Searched Keywords : grinding roller scrap

Get grinding roller scrap Tender Alert...

Related Searched Keywords : grinding roller scrap

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us

Copyright ©2018 - Thetenders.com. Read Policies