Filters

List of hot-water-boiler Tenders

List of latest hot-water-boiler Tenders in Indian Tenders. Click on any hot-water-boiler Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for hot-water-boiler Tenders.

All-Tenders (6)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49053871 | 14 May, 2025

Tender Value : 0

Anantnag - Jammu And Kashmir

Tender for stage contract for sub division anantnag.- stage contract anantnag sub division. 2 engagements of jcbfor execuation of works of various natures 3 surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -all kinds of soil 4 earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed,( all kinds of soil) 5 earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by engineer-in-charge. all kinds of soil : 6 earth work in excavation by manualmeans in trenches for foundations, drains, pipes, cables etc .upto required depth ) and for shafts, wells, cesspits including dressing of sides and ramming of bottoms , including getting out excavated earth and disposal of surplus excavated earth as directed,( all kinds of soil) 7 supply and filling of rbm of specified size including spreading, watering, ramming, compacting with prr of 8 to 10 tonne capacity and including carriage of the same from approved source upto site of work complete 8 felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. 9 beyond 30 cm girth upto and including 60 cm girth. 10 beyond 60 cm girth upto and including 120 cm girth. 11 beyond 120 cm girth upto and including 240 cm girth. 12 banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m in all kinds of soi 13 supply and filling of khak bajri including spreading, watering, ramming, compacting with prr of 8 to 10 tonne capacityincluding carriage of the same from approved source upto site of work complete( for berm) 14 providing / laying of rcc pipes in proper position/ grade including cutting of road surface upto required depth, providing requisite cushion including carriage ofall materials and pipesupto site ofwork complete. 15 10 16 12 17 14 18 16 19 20 20 24 21 32 22 36 23 40 24 48 25 providing / laying of ms pipes in proper position/ grade including cutting of road surface upto required depth, providing requisite cushion including carriage ofall materials and pipesupto site ofwork complete. 26 6 27 8 28 10 29 12 30 scarifying the existing bituminous road surface to a depth of 50mm and disposal of scarified material within all lifts and lead upto 1 km (by mechanical means). 31 scarifying metalled (water-bound) road surface including disposal of rubbish lead upto 50m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity. 32 providing and laying water bound macadam base course with quarry crushed stone aggregate 90 to 45mm size, stone screening 13.20mm size and binding material as per morth specification including screening, sorting, spreading to template and consolidation with prr of 8 to 10 tonne capacity including carriageofquarry crushedstone aggrregateand stone screeing, stone dustfrom approved soucrce upto site of wotk complete(finished work to be measured) 100mm compacted thickness 33 providing and laying water bound macadam base course with quarry crushed stone aggregate 63 to 45mm size, stone screening 13.20mm size and binding material as per morth specification including screening, sorting, spreading to template and consolidation with prr of 8 to 10 tonne capacity including carriageofquarry crushedstone aggrregateand stone screeing, stone dustfrom approved soucrce upto site of wotk complete(finished work to be measured) 75mm compacted thickness 34 providing and laying water bound macadam base course with quarry crushed stone aggregate 53 to 22.4mm size, stone screening 11.20mm size and binding material as per morth specification including screening, sorting, spreading to template and consolidation with prr of 8 to 10 tonne capacity including carriageofquarry crushedstone aggrregateand stone screeing, stone dustfrom approved soucrce upto site of wotk complete(finished work to be measured) 75mm compacted thickness 35 providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (wmm) specification including premixing the material with water at omc in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of engineer-in-charge 36 providing and applying tack coat using hot straight run bitumen of grade –vg-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. on bitumen surface @ 0.50 kg/sqm 37 providing and applying tack coat using hot straight run bitumen of grade –vg-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. on w.b.m. @ 0.75 kg/sqm 38 providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of engineer-in-charge. 50 to 100 mm average compacted thickness with bitumen of grade vg-10 @ 3.5% (percentage by weight of total mix) 39 providing and laying semi- dense bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of engineer-in-charge. 25 mm compacted thickness with bitumen of grade vg 10 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) 40 providing and laying dense graded bituminous macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of engineer-in-charge. 16.62.1 50 to 100 mm average compacted thickness with bitumen of grade vg-30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) prepared in batch type hot mix plant of 100-120 tph capacity. 16.62.2 50 to 100 mm average compacted thickness with bitumen of grade vg-30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) prepared in drum type hot mix plant of 60-90 tph capacity. 41 providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade vg-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete. 42 providing and laying of stone soling, hand packed, including carriage of same from approved source upto site of work complete. 43 providing and laying in position cement concrete in1 : 4 : 8 (1 cement :4 coarse sand : 8 graded crushed stone aggregate, 40mm nominal size) excluding the cost of centering and shuttering but including carriage of all materials from approved sources up to site of work complete. 44 providing and laying in position cement concrete in1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate, 40mm nominal size) excluding the cost of centering and shuttering but including carriage of all materials from approved sources up to site of work complete. 45 providing and laying in position cement concrete in1 : 2 : 4 (1 cement :2 coarse sand : 4 graded crushed stone aggregate, 20mm nominal size) excluding the cost of centering and shuttering but including carriage of all materials from approved sources up to site of work complete. 46 providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. but including carriage of all materials from approved sources up to site of work complete.all works upto plinth level (1: 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 47 providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. but including carriage of all materials from approved sources up to site of work complete.all works upto plinth level (1 : 2 : 4 (1 cement :2 coarse sand : 4 graded crushed stone aggregate, 20mm nominal size)) 48 reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.but including carriage of all materials from approved sources up to site of work complete. (1: 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 49 reinforcement for rcc work including straightening cutting, bending, placing in position and binding all complete (thermo mechanically treated bars) including all carriages complete. fe-500 d or more 50 providing / fixing of necessary farm work / shuttering including strutting, propping etc and removal of same complete 51 foundations, footings, bases for columns 52 return walls, walls (any thickness) including attached pilaster buttresses, plinth and string course fillets, kerbs and steps etc. 53 suspended floors, roofings, landings, balcones and access plateform 54 50mm thick cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished wit a floating coat of neat cement including carriage of all materials from approved sources upto site of work complete 55 40mm thick cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished wit a floating coat of neat cement including carriage of all materials from approved sources upto site of work complete 56 25mm thick cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished wit a floating coat of neat cement including carriage of all materials from approved sources upto site of work complete 57 12mm cement plaster of mix 1:4 (1cement: 4 fine sand) including all carriages complete. 58 12mm cement plaster of mix 1:6 (1cement: 6 fine sand) including all carriages complete. 59 15mm cement plaster of mix 1:4 (1cement: 4 fine sand) including all carriages complete. 60 15mm cement plaster of mix 1:6 (1cement: 6 fine sand) including all carriages complete. 61 dry random rubble masonry in 100 x100mm mesh size g.i wire crate made of 5mm dia g.i wire using bond stones ncluding wrapping /tightening of wire crate and binding wire crates after stone work including cost of all material involed (crates and stones) and carriage of same upto site work complete (quarry stones) 62 random rubble masonry with hard stone (quarry) in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement : 6 coarsesand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of all materials from approved sources up to site of work complete. 63 engagement of labour /masdoor for one day 64 engagement of skilled labour with all machinary like cutters , axe etc for purning of the trees 65 pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 66 removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive 67 clearance of slipsdisposal lead upto 50 m and lift upto 1.5 m. 68 in ordinary soils disposal lead upto 50 m and lift upto 1.5 m. 69 in soils; mixed with moorum/kankar/shingle/boulders; disposal lead upto 50 m and lift upto 1.5 m. 70 in soils; mixed with decomposed rocks; by blasting or any other means 71 providing and applying 2.5mm thick road marking strips (retro-reflective) of specified shade/colour using hot thermoplastic material by fully/semiautomatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, t&p, cleaning the road surface of all dirt, seals, oil, grease and foreignmaterial etc. complete as per direction of engineer-in-charge and accordance with applicable specifications. 72 white washing with lime to give an even shade :old work (two or more coats) 73 white washing with lime to give an even shade :old work (one or more coats) 74 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work 75 painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to is: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.old work ( one or more coats) 76 providing and laying at or near ground level factory made kerb stone of m-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of engineer-incharge (length of finished kerb edging shall be measured for payment). (precast c.c. kerb stone shall be approved by engineer-in-charge). 77 manufacturing supplying and fixing retro reflective sign boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type-iv of astm-d-4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per irc : 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of astm-d-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20cm c/c to back support frame of m.s. angle iron of size 25x25x3mm along with theft resistant measures mounted and fixed with 2 nos. m.s. angles of size 35x35x5mm to a vertical post made upto m.s. tee section ismt 50x50x6mm welded with 16.0 (road work) 224 base plate of size 100x100x5mm at the bottom end and including making holes in pipes, angle flats, providing and fixing m.s. message plate of required size steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical m.s.-tee support to be painted in black and white colours). backside of aluminum sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coats including all leads and lifts etc. complete as per drawing, specification and direction of engineer-in-charge. 16.66.1 mandatory/regulatory sign boards of 900 mm diameter with part as length of 3750 mm. 78 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete 79 structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. welded 80 supply and filling of rbm of specified grade including spreading, watering, ramming, compacting with prr of 8 to 10 tonne capacity material availabe at site

Co-operative

TRN :49063237 | 20 May, 2025

Tender Value : 4.00 Lacs

Muzaffarnagar - Uttar Pradesh

Tender for hardware and general goods , hardware general goods , acc make quick setting compound simcom 30 , alluminium rivit all size , alluminium sheetall size , anabond 666 , angle grinder complet 4raliwolf make , anti seage spray , araldite in 1.80 kg , bearing sleave s k f make no-99435 siz3-110 mm , bearing sleave size h-3144 special size id 198 mm , bearing sleave size h-3144 special size id 198.20 mm , bearing sleeve jmc make all size less discount on company price list , belt fastner no 35 , blue tube in pack of 15 mm , boiler gauge galass 3/4 x 17suitable for very high pressore & hightemp.bishap make , boiler gauge galass 3/4 x 20 1/2suitable for very high pressore & hightemp.bishap make , boiler gauge galass 3/4 x 42suitable for very high pressore & hightemp.bishap make , boler gauge glass sleeveleader make less discount on company price list , bosch make angle grinder ag-4 , bosch make angle grinder ag-7 , brass conector 6 mm , brass conector 10 mm , brass ferrule 10 mm , brass ferrule 6 mm , brass nut 10 mm , brass nut 3 mm , brass nut 6 mm , brass rod all size , brass washer all size , brasso liqued in tin of 100 ml , hindustan make rubber conveyor flat belt (straight grade m-24,4 ply, 12 mm, 5mm top and 3mm bottom size356 mm(14) width , hindustan make rubber conveyor flat belt (straight grade m-24,4 ply, 12 mm, 5mm top and 3mm bottom size 406 mm(16) width , hindustan make rubber conveyor flat belt (straight grade m-24,4 ply, 12 mm, 5mm top and 3mm bottom size 508 mm(20) width , hindustan composite make break liner size 3/8x7 , hindustan composite make break liner size 3/4x9 , hindustan composite make break liner size 3/8x9 , hindustan composite make break liner size 1/2x5 , hindustan composite make break liner matalical copper wiresize 1/2x9 x 1mtr , hindustan composite make breack linner 1/2x7 , hindustan composite make breack linner 1/2x9 , c i cock valve 1 , c i spring loaded angle valve 150 mm (safty valve) with following specification1 ss 410 spindle,s s 304 body seat,ss 304 flap, flap seat of epdm rubbersuitable for 160 c , c.i /g.m.wheel valve, butter flyvalve , & cock valve all size sant make as per company previling price list , c.i /g.m.wheel valve, butter flyvalve , & cock valve all size sant make less discount as per company previling price list , c.i.pulley 10 c section 4 groove 1 pilot bore , c.i.pulley 14odxb section 3 groove 1 bore , c.i.pulley b section size 9 groove 1 , c.i.pulley section size 14 groove 1 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 10 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 12 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 2 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 3 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 4 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 5 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 6 , c.i.sluice valve non rising spindle isi marked aisi-410 spindle gun metal working parts is 14846:2000 size 8 , c.s valve all size w.j.make less discount as per company previling price list , c.s.valve all size audco makeless discount as per company previling price list , camel hair belt 1/2 x 12 , camel hair belt but 1/2 x 10 , canvas hose pipe 63 mm x 15 meter with male femal coupling isi mark (insulated 14 bar) , canvas hose pipe 63 mm x 30 meter with male femal couplingisi mark (insulated 14 bar) , carbide tip tool size 1/4x8 sq , carbon steel seamless long bend sch-40, ibrapproved with mtc size1 1/2 , carbon steel seamless long bend sch-40, ibrapproved with mtc size 1 , carbon steel seamless long bend sch-40, ibrapproved with mtc size 1/2 , carbon steel seamless long bend sch-40, ibrapproved with mtc size 2 , carbon steel seamless long bend sch-40, ibrapproved with mtc size 3/4 , carbon steel seamless steamlong bends astma-106 grade inschedule -40 ibr approved with mtc size 125 mm nb , carbon steel seamless steamlong bends astma-106 grade inschedule -40 ibr approved with mtc size 150 mm nb , carbon steel seamless steamlong bends astma-106 grade inschedule -40 ibr approved with mtc size 20 mm nb , carbon steel seamless steamlong bends astma-106 grade inschedule -40 ibr approved with mtc size 25 mm nb , carbon steel seamless steamlong bends astma-106 grade inschedule -40 ibr approved with mtc size 38/40 mm nb , carbon steel seamless steam long band astm a-106 grade sch -40 ibr with mtc size 15mm , carbon steel seamless steam long band astm a-106 grade sch -40 ibr with mtc size 50mm , carbon steel seamless steam pipe line astma-106 grade inschedule -40 ibr approved with mtc msl make all size as per company prevaling price list , carbon steel steam pipe astm a-106 grade sch -40 ibr with mtc size 15mm , carrage bolt size 3/8x2 1/2 , carrage bolt size 3/8x2 1/2 , cast iron diapharam valve rubber blind size 2 , cast iron foot valve flange type heavy duty size 6 , chain pulley block cap.01ton.indef make with sd lift (p model) , chain pulley block cap.02 ton.indef make with sd lift (p model) , chain pulley block cap.03 ton.indef make with sd lift (p model) , chain pulley block cap.05 ton.indef make with sd lift (p model) , coir stringall size , conveyer rubber belt 1000mmwidth 5 mm top 2mm bottom 8 mm thickness 3 ply nylon m 24 grade hindustaan make , conveyer rubber belt 500mm width 3ply 3mm top 1.5mm bottom m24 grade strengh 315/3hindustaan make , copper molicoat past , copper pipe all size , copper pipe od 10 mm x id 7 mm , copper rivit round head size 5/32x1/2 , copper sheet size 4x4 x 1.5 mm , cotton waste but coluread , cotton waste wihte dust free , counter meter 6 digit heavy duty , csk bolt size 3/4 x 4 , csk bolt size 3/4 x 6 , d cycle 3/4 , c.i.pulley b section size 14 groove 1 , c.i.pulley b section size 9 groove 1 , c.i.pulley but 1/2 x 10 , c.i.pulley but 10 c section 4 groove 1 pilot bore , c.i.pulley but size 1/4x1/4 , c.i.pulley c section size 9 groove 1 , dog chuk double sloth.dutysize- 12 , drillchuck size 1/2 , drillchuck size 3/4 , drill socket set size 0-4 , du chain diamond make 1-1/2 less discount as per company prevaling price list , e.n -8 shaft all size , e.n -8 shaftt with ultrasonic t.c , e.n -9 shaft all size , e.n -9 shaft with ultrasonic t.c , emery cloth in 500 sheet but fine , emery cloth in 500 sheet rough c.u make , emery past 400 gm but fine , emery past 400 gm roughc.u.make , emery tape 50 mtr roll 1 1/2lbut fine , emery tape 50 mtr roll 1 1/2 rough c.u make , emery tape 50 mtr roll 2 rough c.u make , emery tape 50 mtr roll 2t fine , erw tube for super heated wash water column tub size od 20mm x id 15mmapprox 6 to 7.5 mtr , erw tube for super heated wash water column tube od 16mm id 12mm length approx 6 to 7.5 mtr , expande; metal 50x4 , expandeble; material for sulpher furnace size burfi 25 mm wire thck 3 mm , extra chain forchain pulley block cap.01ton.indef make with sd lift (p model) above , extra chain chain pulley block cap.02 ton.indef make with sd lift (p model) , extra chain chain pulley block cap.03 ton.indef make with sd lift (p model) , extra chain chain pulley block cap.0 5ton.indef make with sd lift (p model) , filler gauge size 9 , fire bucket , flate belt all size goodyear makeless discount on as per company prevaling price list , flow meter 4 (cold ) up to 40 c temp , flow meter 4 (hot ) up to 100 c temp , flow meter 6 (cold ) up to 40 c temp , flow meter 6 (hot ) up to 100 c temp , forbes marshall make thermo dynamic steam trap td3 socket weld size 1 , forbes marshall make thermo dynamic steam trap td3 socket weld size 3/4 , forged m.s.socket size 3/8 bsp , four jaw chuck double slots size 12 gmt make , g i bolt with nut 10x100 mm , g i bolt with nut 10x65 mm , g i pipe 2 c class heavy duty , g i plate 2x2 x6mm thik earthing , g i strip size 1/4 x2 , g i washer 10 mm , g m rod all size , g.i bolt galavnisd 1/2 x 5 , g.i. washer 1/2 , g.i.nut galavnisded 1/2 , g.i.wire 16 swg , gasket shallac compound 25 gm tube , gauge glass cock set (broze gauge glass cock set) , gear coupling all size fenner make discountas per company prevaling price list , gmt make 4 jaw chuck double slot for leath machine 12 , gmt make 4 jaw chuck double slot for leath machine size 24 , graphite powder 1/2 kg pack , high pressure wire braided felxible hose pipe withconnectto size 1/2 x 1/2mtr , high pressure wire braided felxible hose pipe withconnectto size 1/2 x 21/2 ft , high pressure wire braided felxible hose pipe withconnectto size 1/4 x 1mtr , high pressure wire braided felxible hose pipe withconnectto size 1/4 x 1 1/2ft , high pressure wire braided felxible hose pipe withconnectto size 1/4 x 1 1/2 mtr , high pressure wire braided felxible hose pipe withconnectto size 1/4 x 1/2 mtr , high pressure wire braided felxible hose pipe withconnectto size 3/4 x 1/2 mte , high pressure wire braided felxible hose pipe withconnectto size 3/4 x 11/2 mte , high pressure wire braided felxible hose pipe withconnecttor - but size 1/2 x 1 mtr , high pressure wire braided felxible hose pipe withconnecttor - but size 1/4 x 1 1/2ft , high pressure wire braided felxible hose pipe withconnecttor but size 1/2 x 11/2 mte , high pressure wire braided felxible hose pipe withconnecttor- but size 1/2 x 1 ft , high pressure wire braided felxible hose pipe withconnecttor- but size 1/2 x 1/2mtr , high pressure wire braided felxible hose pipe withconnecttor but size 1/2 x 21/2 ft , high pressure wire braided felxible hose pipe withconnecttor- but size 1/4 x 1 1/2 mtr , high pressure wire braided felxible hose pipe withconnecttor- but size 1/4 x 1/2 mtr , high pressure wire braided felxible hose pipe withconnecttor- but size 3/4 x 1 mte , high pressure wire braided felxible hose pipe withconnecttor size 3/4 x 3 mtr , holdite compound in 1/2 kgpack , hose pipe clamp 1 1/2 , hose pipe clamp 1 , hose pipe clamp 1/2 , hose pipe clamp 2 , hose pipe clamp 3 , hose pipe clamp 3/4 , hose pipe clamp but 1 1/2 , hose pipe clamp but 1 , hose pipe clamp but 10 mmx6mm id , hose pipe clamp but 2 , hose pipe clamp but 3 , hydrant valve63 mm i s i mark , hydraulicelbow both side nut ferrule 16 mm , hydraulic connector both side ferrule 16 mm , hydraulic forrul but 16 mm , hydraulic forrule size 10 mm , hydraulic hose with end connector female size 1 bsp , hydraulic jack 5 ton cap liver typeh duty , hydraulic seamless pip 10 mmx6mm id , hydraulic seamless pipe 16mm od x 12mm id , in side caliper size 8 , in side caliper size 6 , isi mark c.i non return valve flange end heavy duty size 6 , klingnt make steam joint style 1000- 3 mm metallic , knurling tool internal as per sample , lead super fine shoft flexible , lead wire 500 grm roll size 2mm , linsed oil double boiled tin 20ltr , loctic 574thread locker 250 ml , loctic 641 thread locker 50 ml , loctic thread locker 270 50 ml , m sstud size 1/2x2 1/2 , m sstud size 1/2x4 , m sstud size 10x100 mm , m sstud size 10x60 mm , m sstud size 5/8x2 1/2 , m s flange as per table dod 272 mm,pcd 234 mm holes 8 nos bore 150 mm , m s flange size 150 mm nb , m s flange size 200 mm nb , m s flange size 3 , m s flange size 4 , m s flange size 800 mm nb , m s flat 40 mm x 8 mm , m s short bent sch-40 size 1 1/2 , m s squre bas 50 x 50 mm , m.s blind flange 10 mm thick size 6 , m.s counter shankbolt size 3/4x6 , m.s flange 10 mm thick size 100 mm , m.s flange 10 mm thick size 20 mm , m.s flange 10 mm thick size 50 mm , m.s flange 10 mm thick size 80 mm , m.s flange size 1 1/2 class 300 , m.s flange size 1 1/2 class 300 , m.s long band c class size 2.5 , m.s long band c class size 3 , m.s long band c class size 4 , m.s long band c class size 6 , m.s long band c class size 8 , m.s seamless tube tested at 1000 psi size 10od x 7 id , m.s sturd size 1/2x2.5 , m.s sturd size 12mm x 65mm , m.s sturd size 16mm x 100mm , m.s sturd size 16mm x 65mm , m.s sturd size 20mm x 65mm , m.s tee 1/2 , m.s u clamp size 1 , m.s u clamp size 1/2 , m.s u clamp size 3/4 , m.s.bend 1 (short) , m.s.bend 1/2 (short) , m.s.bend 2 (short) , m.s.bend 3 (short) , m.s.bend 4 (short) , m.s.bend 5 (short) , m.s.bend 6 (short) , m.s.bend 8 (short) , m.s.perforted sheet 3 mm thick 4 x8 xhole dia 5 mm , m.s.rivit all size , m.s.sheet size 4x8 x18 swg , m.s.stud 1/2x2 , m.s.stud 1/2x3 , m.s.stud 12x75mm , m.s.stud 3/4x3 , m.s.stud 3/4x6 , m.s.stud 3/8x3-1/2 , m.s.stud 5/8x3 , m.s.stud but 1/2x3 , m.s.stud but 3/8x3-1/2 , m.s.washer all size , m.s.tube id 16 mm, od 19 mm, lenth-6000mm , m.seal 1 kg pack m & m make , marking block 18 , marking block size 12 , measuring tape fiber glass freeman make 15 mtr long , measuring tape fiber glass freeman make 3 mtr long , measuring tape fiber glass freeman make 5 mtr long , metallic oil seal on metal case 105x160x15 mm , metallic oil seal on metal case 110x130x13 mm , metallic oil seal on metal case 150x180x15 mm , metallic oil seal on metal case 150x275x87 mm , metallic oil seal on metal case 180x150x15 mm , metallic oil seal on metal case 190x220x15 mm , metallic oil seal on metal case 200x300x87 mm , metallic oil seal on metal case 250x350x87 mm , metallic oil seal on metal case 325x450x50 mm , metallic oil seal on metal case 35x57x10 mm , metallic oil seal on metal case 400x 525x50 , metallic oil seal on metal case 90x120x15 mm , metallic oil seal on metal case 250x354x87 , meter meco viberation meter km-63 complete with accessories in carring case , mkkoda make rubber oil seal all size less discount onas perco.prevlingprice list , moly cot powder 1000 , moly cot spray (400 ml can) , namda 10mm , namda 10mm , out side caliper size12 , out side caliper size 6 , p.p ball valve flange end size 2 , p.p.rope size 3/4 with t.c. , p.v.c.pipe 15 mm. , p.v.c.pipe 4 , p.v.c.pipe 6 , p.v.c.pipe but 20 mm , p.v.c.pipe but 25 mm , p.v.c.pipe but 50 mm , p.v.c. transparent pipe 15 mm. , pillow bearing p-210ntn make , pillow bearing t-210ntn make , pillow bearing p-213 ntn make , pillow bearing t-213 ntn make , plumber blockwith bearingp 207 ntn make , plumber blockwith bearingt 207 ntn make , plumber blockwith bearingt 209 ntn make , plumber blockwith bearingp 209 ntn make , plumber block all size smr make less discount as per company previling price list , power ,master make tube expender rod size 42 mm to 45mm , pvc transparent pipe 1/4 , rberised asbestostape size 3/8x 1.5 , rotex make solonoide valve 3013 single way , roto dial make gear oil pump for turbine size 1 cap 50 ltr/min , roto dial make gear oil pump size 1 1/4 cap75 ltr/min , rotodial make gear oil pump for tew make mill turbine 1-1/4 x 1-1/4 75 ltr per minute , rubber hose pipe all size dnlop make less discount as per company previling price list , rubber jointing sheet jyoti make black , rubber tyre coupling complete set size- hp-60 , rubber tyre coupling complete set size- hp-90 , rubber tyre coupling complete set size- hp-96 , rubber tyre coupling complete set size- hp-100 , rubber tyre coupling complete set size- hp-120 , rubber tyre coupling complete set size- hp-126 , rubber tyre coupling complete set size- hp-178 , rubber tyre coupling complete set size- hp-190 , rubber tyre coupling complete set size- hp-250 , rubber tyre coupling complete set size- px-100 , rubber tyre coupling complete set size- px-110 , rubber tyre coupling complete set size- px-120 , rubber tyre coupling complete set size- px-250 , rubber tyre coupling complete set size- ph-160 , rubber tyre coupling complete set size- ph-140 , rubber tyre for coupling ph --60 , rubber tyre for coupling ph --90 , rubber tyre for coupling ph -96 , rubber tyre for coupling ph -100 , rubber tyre for coupling ph -110 , rubber tyre for coupling ph -120 , rubber tyre for coupling ph -126 , rubber tyre for coupling ph -178 , rubber tyre for coupling ph -190 , rubber tyre for coupling ph -250 , rubber tyre for coupling px100 , rubber tyre for coupling px110 , rubber tyre for coupling px120 , rubber tyre for coupling px250 , rubber tyre for coupling ph160 , rubber tyre for coupling ph140 , rustoline 1/2 kg tin , s.s nipple size 1/4x 3/8 , s.s nipplet size 1/4x1/4 , s.s wire netting grade 316 x 4 mesh1 mtr x 4 mtr , s.s.ballvalve size 15 mm , s.s.ballvalve size 50 mm , s.s.ballvalvesize 20 mm , s.s.ballvalvesize 25 mm , s.s.ball valve size 65 mm , s.s.bend h.duty 4 , s.s.bend h.duty 6 , s.s.bend h.duty 8 , s.s.fastener304 hex bolt,nut,washer,allen cap, allen csk ,stud etcless discount as per company previling pricelist , s.s.needle valve h.d.316 grade size 1/2 , s.s.pipe316 l grade , s.s.plate 304 , s.s.rod(shaft) 304 grad all size , s.s.socket 1/4 304 grade , seamles steam sch -40 long bend 4 , seamles steam sch -40 long bend 6 , seamlessshort bend sch-40 siz but 80mm , seamlessshort bend sch-40 size 65mm with ibr tested , seamlessshort bend sch-40 size 80mm with ibr tested , seamless bend 1/2 sch 40 s/w , seamless pipe grade 316 l for boiler , seamless sch-40 with ibr tested 2 short bend , seamless sch-40 with ibr tested 2long bend , seamless short bend -sch 40 size 2 , seamless short bend sch-40 size 1 1/2 , seamless tee 1/2 sw tested up to 3000 lbs , soldring past , soldring past , solonidvalve rotex make2way , solonidvalve rotex make2way , solonidvalve rotex make plate 2 part 2way of one part on way , spare kite for rotex make solonoid vavle 3012 , spare kite for rotex make solonoid vavle 3013 , spare rubber tyre t-5 , spare rubber tyre t-7 , spilit pin all size champion make less discount on company price list , spring stee 125x8 mm , spring stee 65x8 mm , spring steel 40 x 6 mm , spring steel size 100 x 8 mm , spring steel size 45 x 6 mm , spring steet 40 mm x 8 mm , spring washer all size champion make less discount on company price list , ss round 316 grade size 12 mm , ss round 316 grade size 20 mm , ss round 410 grade size 100 mmx3350 mm , ss seamless pipe 10 mm od x 7mm idgrade 316 , stag joint pested (type b red) , stainless steel hydraulic conector as per sample , steam packing wire reignfored metallic style600 champion make/spitman make size- 3 mm , steam packing wire reignfored metallic style600 champion make/spitman make size but 10 mm , steam packing wire reignfored metallic style600 champion make/spitman make size but 12mm , steam packing wire reignfored metallic style600 champion make/spitman make size but 16mm , steam packing wire reignfored metallic style600 champion make/spitman make size but 6mm , steam packing wire reignfored metallic style600 champion make/spitman make size but 8mm , steam wire breaded hose pipe indomakession make all size. less discount as per company previling pricelist , steam/hydrainde pipe line 16 mm , steel ball size 10 mm , steel ball size 12 mm , steel ball size 4 mm , steel ball size 6 mm , steel ball size 8mm , steel wire rope siling dia1/2x 5 mtr long hand make , steel wire rope siling dia 1 1/2x 3 mtr long hand make , steel wire rope with t.c usha martine make all size less discount on as per company previling pricelist , stud with nut size 10x35mm , super wash water pump 2555 ne 1440 prm , taflon rod1 1/4 x12 , taflon rod 3x12 , taflon rod size 1x12 , taflon rod size 3/4x12 , taflon rod size 45x300 mm , taflon rod size but 1 1/2x12 , taflon rod size but 3x12 , taflon tape 3/4 , tap handle 20 mm , taper shink drill 1/2x12 long , test tube , test tube , threadseallocker 50 ml tube , thread gauge mm/bsw , tin cutter size 10 , vaccum hose pipe 2 1/2 x18 , vaccum hose pipe 3 1/2 x18 , vaccum hose pipe but 3 x18 , water flow meter isi mark flange end size 3 , water flow meter isi mark flange end size 4 , water meter size 6 kranti make , wire netting 2 mesh x12 swg x 2.5 mm , wire rope celling1/2 x4 mtr , wire rope cellingbut1/2 x4 mtr , wire rope cellingbut 3/4 x6 mtr , wire rope celling 1 1/2x3 mtr long , wire rope celling 1/2x 3 mtr , wire rope celling 3/4 x6 mtr , wire rope celling but 1/2x 3 mtr , wire rope forged u clamp size 5/8 , wollen flet size 3/81 mtr x 2 mtr , wooden handles wire brushbut 6 x 3 , wooden handles wire brush 6x2

Central Government/Public Sector

TRN :49065978 | 15 May, 2025

Tender Value : 0

Pardi - Gujarat

Tender for auction sale of 98090719 stainless steel/magnet steel scrap released stainless steel/magnet steel misc. such as ss fan guards, impeller,locking rib, chair bench , retention tank assembly,dustbin ,screw, bakda/ 3seaterseats, fan jali, fan ribs, fan blades, drums, mugs, pans, trays, thali, bowl , blower drums, retensiontank, sheets, angles, mouldings, flats, pipes, patti, wash basins, turf sheets, plain sheets and theircut offs, plates, boiler tanks, air filter frames, raf/faf frame, chimney, boiler tank, trey, washbasins,magazine pockets, wall protectors, steam protector boxes atached with thermal insulation, doors, cupboards, bottle holders, liquid container, seaters, tharmas, drums, commode with or without rubber attachments, hot case, blower, e.l. boxes, batterybox, ac frames, squating pan, of table/furniture attachment, hospital operating instruments likescissors, forcepts, etc. dressing drums, , handle pipe rods, water bottle stand, defrizer with or without foam,hot case, defrizer boxes along with all body, stool, blower runner, filter/filter frameswith or without ms jali, liquid container, kitchen items, kitchen utensils like fry pan, spoons, drum,degachi/pot, discs, gas stoves, water tanks/ reservoir tanks with or without m.s. attachments and their cut pieces, broken and damaged, including minor rubber and ms, alluminium attachment, medical tray, dishes, kidney tray, bowl, hospital canteen misc. steels.fire extinguish with or without minor ferous,n/f attachment u/s for rly. use, loading by purchaser.custodian: dms/scrap/pardi.

State Government

TRN :34443376 | 14 May, 2025

Tender Value : 12.28 Lacs

Vijayawada - Andhra Pradesh

Tender for removal & re-fixing of aluminum insulation sheeting on water wall tubes around soot blowers and burner panels, hot venturi ducting of mills, hot air bus ducts, inter connecting duct over aph and id fan to chimney areas of boiler in unit-7 during annual overhaul period 2025-26 dr.nttps

Statutory Bodies and Commissions/Committees

TRN :48666244 | 17 May, 2025

Tender Value : 0

Darjeeling - West Bengal

Tender for bids are invited for hot water boiler of capacity 150 ltrs , hot water boiler of capacity 150 ltrs having average performance to heats 150 ltrs , hot water boiler of capacity 150 ltrs having average performance to heats 150 ltrs of cold water to 50 degree centigrade , hot water boiler of capacity 150 ltrs having average performance to heats 150 ltrs of cold water to 50 degree centigrade in max 30 to 40 min , hot water boiler of capacity 150 ltrs having average performance to heats 150 ltrs of cold water to 50 degree centigrade in max 30 to 40 min fuel consumption not more than 3 to 4 ltrs hot water boiler of capacity 150 ltrs, hot water boiler of capacity 150 ltrs having average performance to heats 150 ltrs, water boiler hot of capacity 150 ltrs having average performance to heats 150 ltrs of cold water to 50 degree centigrade, hot water boiler of capacity 150 ltrs having , water boiler total quantity : 6

Central Government/Public Sector

TRN :48280497 | 17 May, 2025

Tender Value : 4.14 Crore

Leh - Ladakh

Tender for tender for provision of central mi room at nimu(job no 01/nimu stn/amwp/2023-24); 1 lump sum price worked out by the contractor for building worksas listed in schedule ‘a’ part-i representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 43 2 lump sum price worked out by the contractor for (site clearance, excavation & earth work)as listed in schedule ‘a’ part-ii representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 44 3 lump sum price worked out by the contractor for (internal electrification)as listed in schedule ‘a’ part-iii representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 50 4 lump sum price worked out by the contractor for (internal water supply)as listed in schedule ‘a’ part-iv representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 52 5 lump sum price worked out by the contractor for (road, path & hardstanding)as listed in schedule ‘a’ part-v representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 54 6 lump sum price worked out by the contractor for (sewage disposal)as listed in schedule ‘a’ part-vi representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 55 7 lump sum price worked out by the contractor for (area drainage)as listed in schedule ‘a’ part-vii representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 56 8 lump sum price worked out by the contractor for (shed for dg set)as listed in schedule ‘a’ part-viii representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 58 9 lump sum price worked out by the contractor for (hot water supply)as listed in schedule ‘a’ part-ix representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 59 10 lump sum price worked out by the contractor for (external electrification)as listed in schedule ‘a’ part-x representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 65 11 lump sum price worked out by the contractor for (external water suplay)as listed in schedule ‘a’ part-xi representing percentage ( + or - denomination) derived under last column of this schedule above/belowthe lump sum price prepriced by the mes b/f from sl page no. 66 12 sch a part - xii (misc b/r & e/m items) (refer boq)note: this schedule is not pre-priced by mes and the rate indicated as rs 0.00 under col 5 signifies this fact only 13 internal electrifications&f double door three phase prewired distribution board vertical db vtpn 8 way with acrylic door made out of crca sheets 1.6 mm thick,phosphatised powder coated with copper bus bar 200 amps, 415 v,ip 43/ik09, earth stud, din rail, polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box ,ground terminal blocks ,duly prewired with thimbled flame retardant copper conductors and poly layer for protection in and includingmccb4 pole 63 amp rating repturing capacity 16 ka.(note:- single phase mcbs are to be measured and paid for seperately) 14 s&f led building security light, pressure die cast aluminum housing, 20/25 watts capacity, 240v, ip 65 class, with suitable in-built electronic driver complete incld. fixed on a bracket made out of 1.5 mtr long med grade gi pipe 40 mm dia bend to shape as directed fitted on wall at a height not less than 5 mtr from groundwith ms clamp, nuts and bolts and washers as required at site and incld. connecting luminarie to the nearest ceiling rose/junction box with 1.5 sqmm pvc insulated 3 core wire complete all as directed and specified by engr-in-charge.note - cost of all minor spares and jobs required for fixing of light fixture on wall and for electrical connections are deemed to be included in the quoted rate. 15 s&f new wall mounted fan of approved make and type complete all as specified and as directed. 16 s&f tv co-axial socket 1 module, complete all as specified and as directed. 17 s&f single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole mcb 20 amps 18 internal water supplys&f single piece vitreous china wash down water closet pan pedestal pattern white, with seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminized hinging deviced including flushing system , pipe and joint etc and connection to drain, flushing, pipe, anti-syphonage pipe, and fixing arrangements with fixing bolts etc including making good the disturbed portion of floor in cement concrete 1:2:4 type b-0, as in repairs complete all as spd & directed complete all as specified and directed by engr-in charge.. 19 s&f cp grating including jointing to waste pipe fixed in cement concrete type b-1 (1:2:4) dia of outlet is 100 mm complete all as specified and directed by engr-in charge. 20 s&f hand shower (health faucet ) with 8mm dia and 1 meter long cp flexible tube and wall hookcomplete all as specified make: cera, jaquar , marc & hindware as per sample and directed by engr -in charge 21 s&f soap dish (s/s), any type, fixed to plugs with chromium plated brass screws, all as specified and directed by engr-in charge. 22 road, path & hard standingm&l for wet mix macadam (wmm) for 150mm thick (compacted thickness) laid in two layers of 75mm each grading as per table 400-13 of morth (ministry of road transport & highways) specification of road and bridge works 2013. manufactured in wmm plant, material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-100 kn static weight and conslidating required gradient and camber. the finished surface tolerance to be as per table 900-1 of morth specification for road and bridge works 2013 complete all as specified and directed by engr-in-charge. 23 m&l for applying thermoplastic paint marking 2.5mm thick centerline ,stop line,dashes,arrows etc and n exc 10cm wide on roads pavements with hot applied thermoplastic road marking paint ofapproved colour confirming to bs 3262-1989 with special applicater machine all as per manufacturers instructionof any colour on road surfaceincluding cleaning with gunny bags removing all loose dirt/dust complete all as specified and directed. 24 m&l for rcc septic tank designed to carry sewage and sullage water, excavation in any type of soil, pcc 1:4:8 below foundation, rcc m-30 design mix in walls , base slab , baffle walls and roof slab including beams etc with vent shaft , manhole openings with cover connection etc, complete with effective depth of 1.5 meter and overall depth of 3 meter for 100 users. 25 m&l for soakage wells excavation, in any type of soil, foundation in pcc 1:3:6, walls of honey combed masonry with top ring of m25 concrete including intercepting chamber and screen chamber made of brick masonary in cm, rcc cover slab in m25/ sfrc cover, interconnecting pipes of rcc/dwc complete filled with brick bats of size 3m dia and 3 m depth. 26 s&f pvc junction boxes ip 65 protection of size 0.200 x 0.250 x 0.155 m complete with 1 nos mcb sp 2.5 amp & 4 way industrial connector including clamp made out of ms flat 30x5mm connection from junction box to street light fitting with three single core pvc insulated, pvc sheathed wire 2.5 sqmm copper & pvc conduit 20 mm dia complete all as specified and directed by engr-in-charge. 27 excavation in trenches by cutting of road crossing/pcc hard standing, under boundary wallfor laying of pipe/cable including making good the existing surface with same finish to match the original finish complete all as specified and directed by engr-in-charge. 28 s&fht/lt ms cable route indicator 4 dia fixed with two nos of nut, bolt and washers and provision of pcc 1 : 4 : 8 type d-2 using 40 mm grade stone aggregate of not less than 0.018 cum in each at base buried under the groundincl necessary earth work complete all as specified and directed by engr-in-charge. 29 supply, installation, testing and commissinoning lt panel board suitable for working on 3 phase ,4 wire ,415 volts, ac ,50hz indoortype, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation factory fabricated made out of 2 mm thick crca sheetduly powder coated and shall be cpri approved and as approved by ge. the panel shall have front and rear opening, locking arrangement, cable alleys, bus bar chamber and switch gear compartment, hinged door with rubber gasket, bottom cable entry holes for incoming and out going cables, earthing terminals, affix danger notice plate, glands, copper bus bar duly covered with heat shrink sleeves colour coaded duly fixed ondmc/smc insulators, housed in a separate bus bar chamber and control wiring with copper conductor cables of adequate size and length, incoming and outgoing mccbs shall have extended bus bar links and mounted on 50x50x5mm sizems angle iron frame duly painted including pcc 1:2:4 type b1 (using 20 mm graded stone aggregate ) in foundation design subject to approved of age (i) nimu to sent the site requirementcomplete all as specified and directed including comprising of following :- 30 (a) mccb 400 amps, fp, 36 ka, 415 volts, 50hz - 01 no (i/c)(b) mccb 200 amps, fp, 25 ka, 415 volts, 50hz - 02 no ( chs)(c) mccb 125 amps, fp, 18 ka, 415 volts, 50hz - 04 nos (apfc, tpn db -02, spare )(d) mcb spn 40 amps, 10 ka, 220 volts, 50hz - 03 nos (garage,street light, spare-1)(e) on load chengeover 630 amps 4 pole -01 no (f)digital voltmeter, with vss - 01set(g) digital ammeter, with cts & ass - 01 set(h) led phase indication lamps ryb - 01 set(j)single phase rotary automatic light controller nature switch with voltage range 120-440v,ac,20 amps,ip-65,50hz-01 nos(k) copper bus bar tpn 600 amps rating - 01 set 31 labour for boring underground upto 100 mm bore for road crossing 3 mtr to 10 mtr not exceeding 1.5 mtr in depth for laying of electric cable and gi tubing in soft/loose soil complete all as specified. 32 m&lfor cutting existing gi pipes and insertion of new tee branches of suitable size to take branch connection of 50mm dia pp-r.note : suitable size of tee branch is deemed to be included in the quoted rate. 33 construction of stone masonary valve pit chamber of size 90cm x 90 cm x 90 cm (internal dimension) including all necessary excavation and earthwork in hard / dense soil and disposal of surplus soil to a distance not exceeding 50 meters & deposting the same as directed includingpcc in foundation of the mixture (1:4:8) d-2 stone masonary in cement motor 1:4 rendering 15mm thick in cement mortar 1:4 internally finished even and fair and pointing flush externally as the work proceeds in the same mortar as of stone masonary including mild steelframe (made out ofangle in 40x40x6mm) ms steel cover 3.15 mm thick with handle and locking arrangement with ginges angle iron flat as requiredat site including painting of all posed ms work with two coat of synthetic enamel paint over a coat of red oxide primer and painting all the steel surfaces embedded in pcc with two coats of black bituminuos paint andall other relevant work complete . 34 m&l for providing tracer/anti freezing cable required to keep the pipe warm upto avoiding freezing all as specified including electrical wiring cable for connection of suitable size 35 (central heating system)electric hot water generator : supply, installation, testing and commissioning ofpackage type electric hot water generator constructed out of ms sheet having top open-able cover for easy access and removal of heaters. the hwg shall be suitable for indoor mounting. the generator shall be provided with 50mm thick fibre glass insulation 32 kg density finished with 0.8mm / 22g aluminium cladding sheet. the generator shall have electrical capacity of 50 kw. the heater shall be electrical resistance type, copper tube with chromium plating. the generator shall be complete with float valve, pressure gauge with ball valve, master and bank thermostats, etc. the generator shall be suitable for 3 phase, 415+ 10% volts, 50 hz. ac supply. the generator shall complete with self-contained incoming isolation, ammeter, voltmeter, contactors for heater banks in three steps complete with manual/auto rotary switches. 36 notes:- (i) allneccassary accessories required for the proper fucntioning of hot water genearator are included in price.(ii) the prices should include lifting, shifting and positioning of units at site.(iii) hot water genearator installation to done as per manufacturer recommendation with all installation requirements i.e foundation, vibration isolator,insulationetc as recommended by manufacturer for the ambient temperature of site. odu installation is included in odu price which includes the civil struture, mechanical structureetc as recommended bymanufacturer.(iv) the contractor/oem will shall submit the hot water generator capacity/burner capacity conforming to relevant is code(v) oem should submit the installation and maintenance schedule/ manual for the boiler. 37 glycol circulation centrifugal pumps: supply, installation, testing & commissioning of pn16 ratedaxial split coupled vertical inline water pump set with ci casing, bronze impeller, ss shaft and externally flushed outside type balanced mechanical seal and non overloading motor, as per specifications and drawings. with suitable hp, tefc squirrel cage induction motor with ie3 type class f insulation, motor shall be rating of ip 55, operating on 415 ±10% volts, 3 phase, 50hz ac supply. the external flush line must be used for the purpose of heat dissipation from the mechanical seal.pumps with performance characteristics as given below:the internal components of pumps including mechanical seal shall be suitable to sustain a fluid temperature of -25 degree celcius to 120 degree celcius. vendor shall be provide antivibration arrangement for pumps . 38 the scope also shall include following below mentioned:(i) electrical by pass starter for pump setas recommended by oem. (ii) 25 mm thick polyviny nitrile rubber insulation duly cladded between aluminium sheets of 0.5mm thickness and properly clamped to pump.(iii) pressure gauges 150 mm dia -03 nos (iv) mounting frame with antivibration pads (in case pumps are inline, anti vibration system shall be as per manufacturers recommendation) (v) rcc/cement concrete foundation for the pump unit. (in case pumps are inline, foundation shall be as per manufacturers recommendation).pump capacity are as under:capacityand pump headnot less than flow 25 usgpm , head 20 mtr (refernce model no. : armstrong : series 4300 - 40-150 - 2p - 1.5 kw) each including the triple duty valve and end suction guide. 39 expansion tank and pressurisation unit:supply, installation, testing and commissioning of insulated pressurised closed water expansion tank suitable for total volume ofglycol - water solution, circuit along with necessary accessories such as along with necessary accessories such as 2 nos pumps (1working +1standby) with pressure transmitter andinterconnecting pipe & isolating valve complete with piping connections, safety relief valve, drain valve, pressure gauge, automatic air purging arrangement, etc.with pressure transmitter andinterconnecting pipe & isolating valve complete with piping connections, safety relief valve, drain valve, pressure gauge, automatic air purging arrangement, etc. the tank shall be pre-charged. expansion tank shall be with replaceable heavy duty butyl rubber bladder. the tankconnections should be as per oem recommendationsand 20 mm drain and charging valve connection to facilitate the on site charging of nitrogen in the tank.the tank shall be fitted with lifting rings and a floor mounting skirt for vertical installation. the tank must be constructed in accordance with is-standard 2825-1969 (withlates revision)and rated at pn 16 . the complete system shall be sourced from single manufacturer and supplied and installed with all accessories and safety fixtures required for proper functioning of the complete hydronic system.the tank shall be duly painted in approved colour shall be complete with pressure switches and power distribution and control panelip55 control panel, pressure transmitter, interconnecting piping & wiring. (tank capacity 500 ltrs). hot glycol - water closed vessel pressurized expansion tank as described above shall be duly insulated with 50 mm thick puf/nitrile rubber insulating material or equivalent u valueinsulating material and cladded with aluminium sheet (20g). electrical by pass starter for pump setas recommended by oem. 40 expansion tank of 500 lts capacity 41 pressurization unit: for pump set -03 nos with control panel and accessories. 42 make up tank: supply, installation, testing and commissioning of factory made make up water tank, rectangular/circular shape, of 4 mm thick ms sheet (is 2062), of capacity of 550 litres complete with inlet, outlet, overflow, drain pipe of ms and vent with flame arrestor. tank will be provided with supports made out of minimum 50mm angle iron duly painted, to keep tank base at minimum (1000mm) above ffl. service platform shall be provided as per recommendations of oem. the tank shall be provided with remote indication of levels provided level switches for on-off operation of tranfer pump. extra high level and extra low level alarm shall be provided. tank and structure shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.make up water tank as describedabove should beduly insulated with 50 mm thick puf/nitrile rubber insulating material and cladded with aluminium sheet (20g). 43 supply, installation, testing and commissioning ofsteel plate radiator( wall mounted) confirming en- 442 , working pressurerange from 10-13 bar having workinh temparture of 110°c, complete with top grill side cover as standard along with inlet ,outlet valve, air purge valve andwith threaded plug, flow regulator as per oem.the below desired capacity should be calculated at altitude of 3600 mts above sea level. capacity calculation sheet to be provided to engineer in charge. the below mentioned capacity is at inlet temp: 75 degree celcius , outlet temp: 65 degree celcius. referemcwe model series. 44 1.5 kw, type: 33- dkek, length is 1000 mm and height is 600 mm of radiator. 45 2.5 kw, type: 33- dkek, length is 1000 mm and height is 600 mm of radiator. 46 3.5 kw,type: 33- dkek, length is 1600 mm and height is 600 mm of radiator. 47 5 kw,type: 33- dkek, length is 1600 mm and height is 900 mm of radiator. 48 5 kw,type: 33- dkek, length is 2000 mm and height is 600 mm of radiator 49 m & l for pre-insulated ms pipe,class c havingminimum thicknes of puf insulation as mentioned below and of density 36 kg/cum and 26 gauge al cladding complete suitable for above ground as per sizes shown.the pipes should be insulated with closed cell puf of density 36±2 kg/cum of below mentioned thickness. the pipe should be workable in the temp. range of-50 degree celciusto120 degreec celcius. note:-the pipes size 150mm & below shall be m.s. ‘c’ class as per is : 1239 50 80 mm with 36 mm puf thicknes and 26 gauge al cladding. 51 50 mm with 36 mm puf thicknes and 26 gauge al cladding. 52 50 mm with 36 mm puf thicknes and 26 gauge al cladding. 53 40 mm with 36 mm puf thicknes and 26 gauge al cladding. 54 20 mm with 36 mm puf thicknes and 26 gauge al cladding. 55 buried under ground/exposed to ambient:80 mm with 50 mm puf thicknes and hdpe cladding, 26 gauge al cladding. 56 cabel tray :-supplying and installing following size of perforated painted with powder coating m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling/ground/wall with m.s. suspenders as per is code including bolts & nuts, painting suspenders etc. as required of size 150 mm width x 50 mm depth x 1.6 mm thickness 57 supplying, fixing, testing and commissioning of following diameter valves (pn-16 rating) (complete with flanges integral or welded, fittings, nuts, bolts & gaskets (pn-16 rating), strainers (complete with flanges integral or welded, fittings, nuts, bolts & gaskets (pn-16 rating), gauges etc for condenser water circulation as per specifications. insulation thickness ofvalves should be equal to the insulation of puf and gi cladding of pipe section as specified. butterfly valve ( insulated valves) with ci body ss disc nitrile sheet & o ring, complete with fittings, nuts, bolts & gaskets.butterfly valve ( insulated valves) with ci body ss disc nitrile sheet & o ring, complete with fittings, nuts, bolts & gaskets. 58 80 mm dia butterfly valve 59 65 mm dia butterfly valve 60 50 mm dia butterfly valve 61 supplying, fixing, testing and commissioning of y-strainer (insulated valves) of ductile ci body flanged ends with stainless steel strainer forhot water circulation including insulation thickness ofvalves should be equal to the insulation of puf and gi cladding of pipe section as specified of size 50 mm dia y strainer. 62 supplying, fixing, testing and commissioning of non - return valve (insulated valves) with duel plate of ci body ss plates vulcanized nbr seal flanged end & pn 16 pressure rating forhot water circulation includinginsulation thickness ofvalves should be equal to the insulation of puf and gi cladding of pipe section as sepcified of size 50 mm dia nrv. 63 supplying, fixing, testing and commissioning of automatic air purge valves forhot water circulation headeras specified of size automtic air purge valve 20 mm dia. 64 supplying, fixing, testing and commissioning of air separator compleate allas specified of size 50 mm dia. 65 supplying, fixing, testing and commissioning of water pressure gauge (100 mm dia) bourdon type with brass ball valve of 3/8 dia and ss tubing, socket.range (0-50) / (0-100) as required by engineer in charge. 66 supplying, fixing, testing and commissioning of mercury in glass industrial thermometer in ss-304 casing with 0.5 c least count, range 0-50 c. brass oil filled thermowell of 1/2 size as required by engineer in charge. 67 electrical distribution panel supply, installation, commissioning and testing of factory made, chs plant, indoor type made out of crca sheet 2 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with ms angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 phase4 wire, 415 volts, 50 hz, ac supply system, floor mounted and grounting the legs of panel in pcc foundation 1:4:8 complete as all directed suitable for and including the following :- 68 incomers(i) bus bar tpn al extensible type main bus bars of minimum of 600 a capacity (as per capacity of corresponding incoming / bus couplers) , and auxilliary bus bars ofsuitable capacity with heat shrunk coloured sleeves and i/c smc bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of50ka .(ii)mccb 400 amps, 415 volt, 36 ka, 4 pole,microprocessor release- 01 no for incoming (extended rotary operating handle, phase spreader links and phase barriers ) make: legrand/schenider/simensoutgoings(i) 3nos- 125a ,25 ka tpnmccb/acbwith microprocessor release (3# hot water generator)(ii) mcb 10 amp,tpn,10ka, c curve - 06, 3 nos for pumps , 2 nos for pumps ,01 nos for glycol transfer pump(iii) led phase indication lamps (01 set) with 2amp back up mcb,breaker on/off indicating light with 2a mcb, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. - 2 set (iv) digital ammeter with in built ass,metering c.t.scast resin type, 15va, and accuracy class-1of 800/5a for measuring current in each phase - 01 set.(v) all accessories prewired with appropriate size copper strip or wire and thimbles etc. all as required including foundations as per manufacturers recommendations all as directed by engnr-in-charge.note : contractor will submit the drawing for approval of panel to ge before execution. 69 lt cables : supply & laying/ fixing of following size xlpe insulated and pvc sheathed copper conductor armoured cable/unarmoured as required of 1.1 kv grade complete as require (isi marked) (in ground/in pipe/in duct/on surface/on cable tray) 70 3.5 core x 70 sq.mm. (electric hot water generator) 71 4.0 core x 10 sq.mm. (pump) and (pressurization unit) 72 2 core x 10 sq.mm. (pump) 73 2 core x 6 sq.mm (pressurization unit) 74 earthing complete with copperearth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers etc and connected to and including copper strip of size 32x6 mm up to 7.5 mtr by means of bolts, nuts, check nuts and washers made of brass and protected by light grade 40mm dia upto 7.5 mtr long gi pipe connected to main controlboard and gi pipe light grade 20mm bore for watering and including funnel, wire mesh, rcc pit cover 50mm thick and pcc chamber pit with pcc 1:2:4 type c2 (including excavation and earth work disposal of surplus soil to a distance not exceeding 50 metre) and testing making test point and testing after completion all as specified and shown on plate no 3 of ssr part-i 2009 complete all as specified & directed by engr-in-charge 75 s&f rubber matting conforming to is-15652-2006 complete as required. of size2m x 1m x 25 mm 76 glycol - water solutionsupplying of ethylene glycol concentrate along with the necessary additives and inhibitor in cognition in sealed barrels complete all as directed.note;- (i) the glycol concentrate shall be mixed with potable water supplied by contractor and filled in central heating system pipe line after proper leak test of entire circuit. the glycol water mixture ratio shall be 45 : 55 and freezing temperature shall be - 45 degree celcius (ii) first charge of glycol is included in the quoted rate. first charge include charge in chs pipe linestorage tank. (glycol 45 % ,water 55 %) 77 for chs 78 supply of gycol for running of plant for 12 months 79 glycol circulating pump: supply, erection, testing and commissioning oftransfer pumps for the capacity of 5 lpm 5 meter head for glycol fluidtransfer with base frame foundation, bolts coupling coupling guard,tefc, (oem design hp for the required flowand head ) andother accessories for proper function of the pump. 80 oxygen gas manhold : supply , installation , testing and commission 4+4 oxygen manifold with middle frame, tail pipe, nrv and essab make 10x14 regulator complete all as specified and directed by engr in charge . 81 supply , installation , testing and commission 3 cylinder emergency inlet for oxygen complete all as specified and directed by engr in charge . 82 supply , installation , testing and commission automatic control panel with analog display 02 for oxygen complete all as specified and directed by engr in charge. 83 s&f of copper tubing of size 15 mm od, en -13348 grade , 0.9 mm wall thickness including proper saddling , clamping and insertion of branches connections including all fitting for medical use, complete all as specified and directed by engr in charge. 84 s&f of copper tubing of size 12 mm od, en -13348 grade , 0.9 mm wall thickness including proper saddling , clamping and insertion of branches connections including all fitting for medical use, complete all as specified and directed by engr in charge. 85 s&f bs type gas outle with probe for oxygen for medical compleate all as specified and directed by engr in charge 86 s&f 1/2 brass ball valve with end fittings including all fittings for medical usecomplete all as specified and directed by engr in charge. 87 s&f bpc flow meter (0-15 lpm) including humidfire bottle complete all as specified and directed by engr in charge . 88 s&f 3/8 brass ball valveincluding all fittings for complete all as specified and directed by engr in charge. 89 stand by dg set : supply,install, test and commissioning of silent diesel engine generating set 415 volts, 3 phase, 4 wireengine as per is08528 conforming to cpcb norms iv, and alternator as per is08528 of capacity 400 kva at ntp with control panel having meters, sound proof canopy etc with foundation (as per oem design) including all accessories as per manufactures standard and as per the details given below and independent relay panel for automatic on mains failure:- ac generator should be suitable for ambient conditions at nimu leh area. 90 (a) alternator : standard design alternator rated at 400 kva (320kw)net output at power factor 0.8, ac, 3 phase 4 wire, 415 v, 50 cycles/second, 1500 rpm self excited, self regulated, screen protected, drip proof ip 23 enclosure, brush less design, voltage regulation ± 2.5 % rated voltage from no load to full load and frequency regulation within ± 1.5 % tolerence. (b)diesel engine : vertical diesel engine of suitable capacity, water cooled, closed circuit as per bs-649 or is-1002 direct injection type turbo charged, electric starting system having rated speed 1500 rpm. the dg set shall be capable for running with 10% over loading for 01 hour in every 12 hours as perbs-5514/bs-649. engine shall be multi cylinder, multi stroke, direct injection andequipped with all standard fitting as per manufactures recommendations and mounted on common base frame with following specifications.(a) fly wheel with housing (i) common base frame of sturdy design suitable for anti vibration mounting and permanent concrete foundation for mounting engine and alternator as per manufacturers instructions (b) cooling system (i) radiator with fan & belts & guard, rubber hoses and thermostat. (ii) cooling water pump centrifugal type . 91 (c) governer : electronic governer (d) electric starting system : electric self starter , 24 volts dc(12 volt, 150 ah battery 2 nos)charging alternatoraspermanufacturers design,copper leads with lugs of adequate size complete with initial charging of maintenance free battery 2x12 volt 150 ah capacity. (e) generator monitoring panel : comprising of following :- (i) microprocessor based genset controller for metering, monitoring, governing and protection. (ii) engine protection for low lub oil pressure, high coolant temperature (alarm & shutdown) (iii) alternator protection parameters like under voltage, over current, under frequency, over frequency (alarm & shut down) (f) accessories:avm pads built or separately mounted to manufacturer base frames. (g) coupling arrangements: fixed coupling, flywheel to suit fixed coupling and fly wheel housing.(h) exhaust system : should have equipped with emission control device as per latest govt norms. silencer complete with exhaust pipe of suitable size upto and out side the building all covered with asbestos rope of suitable size all as specified and as directed.(j) fuel tank: daily service fuel tank of capacity suitable for 8 hours continuous operation made out of 3 mm thick (heat retardant) sheet with indicating gauge, built inside the acoustic enclosures or as per manufacturers design 92 (c)acoustic enclosure : all as per cpcb norms iv and oem of dg sets design.(d)amf panel : supply, install, testing and commissioning of amf panel outdoor type, cubical body,dust and vermin proofmade up of crca sheet painted with two coats of synthetic enamelled paint over a coat of red oxide primer confirming to ip 45 with front and rear opening with louvers andmounted on floor with pcc pedestal pillars with a clearance of atleast 0.3 m above ground level with glands sockets etc with provision of cable entry from bottom all pre wired and connected complete with following accessories:-(i) microprocessor based panel -01 no(ii) power contactor heavy duty suitable for generator and mains (iii) over load relay for genset (iv) suitable rating isolating switch mccb for both dg & main supply.(v) multi functioning meter to indicate voltage, current, frequency, p f, kw & kwh etc (vi) emergency stop push button.(vii)set of indicaters : - (a)low lube oil pressure (b) dg set over load(viii) push button to start, stop (ix) mode selector switch i.e auto/manual/test/ off.(x) set of instrument fuse (xi)set of aluminium bus bar of 600 amps capacity 3 ph, 4 wire system (xii) automatic battery charging unit with dc voltmeter, ammeter and selector switch for trickle/ boost charging.(xiii) by pass arrangement of main supply when amf circuit fail due to any fault with provision of suitable rating change overs and switches. 93 the following items are deemed to be included in the rate quoted for all dg sets:- (i) dhpp for testing purpose shall be supplied by the contractor without any extra cost to department. (ii)the contractor shall arrange for artificial load (water load/electrical load) for testing for final testing of dg set at site and the cost is deemed to be including in above offer. (iii) testing of sound level should carried out at the site in presence of engineer-in-charge(iv) one set of latest spare part catalogue with price, exploded view of parts and users manual are deemed to be included in the quoted rate.(v) all civil works including foundation for dgset as per manufacturers drawing/ specification, foundation for amf panel shall deemed to be included in the quoted rate.(vi) the rate quoted is deemed to be included for initial filling of radiator coolant and lubricating oil upto level.

Related Searched Keywords : hot water boiler

List of hot-water-boiler Tenders

Tender for removal & re-fixing of aluminum insulation sheeting on water wall tubes around soot blowers and burner panels, hot venturi ducting of mills, hot air bus ducts, inter connecting duct over aph and id fan to chimney areas of boiler in unit-7 during annual overhaul period 2025-26 dr.nttps

Get hot water boiler Tender Alert...

Related Searched Keywords : hot water boiler

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us