Filters

List of ply-board-scrap Tenders

List of latest ply-board-scrap Tenders in Indian Tenders. Click on any ply-board-scrap Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for ply-board-scrap Tenders.

All-Tenders (5)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49019760 | 13 May, 2025

Tender Value : 0

Kanpur - Uttar Pradesh

Tender for tender for pd campus colony - dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr -15.56 2 12 mm cement plaster of mixwith 1:6 (1 cement: 6 coarse sand) dsr 13.4.2 on wall. 3 12 mm cement plaster of mixwith 1:4 (1 cement: 4 coarse sand) dsr 13.4.1 on celling. 4 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws.dsr-9.21.1 5 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with second class teak wood beading 62x19 mm.dsr-9.51.1 6 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. completedsr - 13.88 7 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.dsr-13.80 8 finishing walls with water proofing cement paint of required shade .( old work one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. ) dsr-13.109.1 9 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour .dsr-13.81 10 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old workdsr-13.99.1 11 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc.15 mm nominal dia pipes . dsr 18.8.1 12 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 25 mm nominal dia pipes . dsr 18.8.3 13 providing and fixing c.p. brass bib cock of pproved quality conforming to is:8931 : 15 mm nominal bore sor/dsr 18.49.1 14 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. white vitreous china wash basin size 630x450 mm with asingle 15 mm c.p. brass pillar tap dsr 17.7.2 15 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests dsr 17.1.2 16 brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to is: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) . with f.p.s.(non modular) bricks .dsr-6.4.2 17 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate dsr 11.3.1 18 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity - white .dsr-17.18.1 19 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr-18.48 20 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). dsr 4.1.8 21 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter dsr12.41.2 22 renewing glass panes, with putty and nails wherever necessary including racking out the old putty:float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) dsr14.5.1 23 cleaning of chocked sewer line by diesel running vehicle mountinghydraulic operated high pressure suction cum jetting sewer cleaningmachine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 psi for sewer line from 150 mm dia upto 300 mm dsr 14.77

State Government

TRN :49020042 | 13 May, 2025

Tender Value : 0

Kanpur - Uttar Pradesh

Tender for tender for annual repair to rawatpur colony type-iv servant qatar - dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr -15.56 2 12 mm cement plaster of mixwith 1:6 (1 cement: 6 coarse sand) dsr 13.4.2 on wall. 3 12 mm cement plaster of mixwith 1:4 (1 cement: 4 coarse sand) dsr 13.4.1 on celling. 4 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws.dsr-9.21.1 5 providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete :200x10 mm dsr9.74.2 6 providing and fixing bright finished brass door latch with necessary screwsetc. complete :300x16x5 mm dsr 9.75.1 7 providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per is: 1378) 300x16 mm dsr 9.62.2 8 providing and fixing bright finished brass handles with screws etc.complete: 125 mm dsr 9.81.3 9 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete dsr 9.82 10 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with second class teak wood beading 62x19 mm.dsr-9.51.1 11 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. completedsr - 13.88 12 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.dsr-13.80 13 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade old work (two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface dsr-13.112.1 14 finishing walls with water proofing cement paint of required shade .( old work one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. ) dsr-13.109.1 15 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour .dsr-13.81 16 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old workdsr-13.99.1 17 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete. dsr-11.39 18 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complet size of tile 600x600 mm .dsr-14.41.2 19 providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of engineer-in-charge. with granite stone of area less than 0.50 sqm. dsr 16.86.1 20 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc.15 mm nominal dia pipes . dsr 18.8.1 21 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 25 mm nominal dia pipes . dsr 18.8.3 22 providing and fixing c.p. brass bib cock of pproved quality conforming to is:8931 : 15 mm nominal bore sor/dsr 18.49.1 23 providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 15 mm nominal bore sor/dsr 18.50.1 24 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15 mm nominal bore sor/dsr 18.53.1 25 providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931.15 mm nominal bore dsr 18.52.1 26 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. white vitreous china wash basin size 630x450 mm with asingle 15 mm c.p. brass pillar tap dsr 17.7.2 27 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests dsr 17.1.2 28 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredw.c. pan with isi marked white solid plastic seat and lid dsr 17.2.1 29 providing and fixing kitchen sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: 17.9.1 white glazed fire clay kitchen sink of size 600x450x 250 mm .dsr -17.9.1 30 providing and fixing t-iron frames for doors, windows and ventilators of mild steel teesections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).40x40x6mm@3.5kg/m . dsr 10.13.1 31 brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to is: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) . with f.p.s.(non modular) bricks .dsr-6.4.2 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate dsr 11.3.1 33 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity - white .dsr-17.18.1 34 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr-18.48 35 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter dsr12.41.2 36 renewing glass panes, with wooden fillets wherever necessary:float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) dsr14.6.1 37 cleaning of chocked sewer line by diesel running vehicle mountinghydraulic operated high pressure suction cum jetting sewer cleaningmachine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 psi for sewer line from 150 mm dia upto 300 mm dsr 14.77 38 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) dsr 5.2.2 39 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo-mechanically treated bars of grade fe-500d or more.dsr 5.22a.6 40 centering and shuttering including strutting, propping etc. and removal of form work for : columns, piers, abutments, pillars, posts and struts.dsr 4.3.3

State Government

TRN :49020061 | 13 May, 2025

Tender Value : 0

Kanpur - Uttar Pradesh

Tender for tender for annual repair to mc robertganj colony - dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr -15.56 2 12 mm cement plaster of mixwith 1:6 (1 cement: 6 coarse sand) dsr 13.4.2 on wall. 3 12 mm cement plaster of mixwith 1:4 (1 cement: 4 coarse sand) dsr 13.4.1 on celling. 4 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws.dsr-9.21.1 5 providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete :200x10 mm dsr9.74.2 6 providing and fixing bright finished brass door latch with necessary screwsetc. complete :300x16x5 mm dsr 9.75.1 7 providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per is: 1378) 300x16 mm dsr 9.62.2 8 providing and fixing bright finished brass handles with screws etc.complete: 125 mm dsr 9.81.3 9 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete dsr 9.82 10 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with second class teak wood beading 62x19 mm.dsr-9.51.1 11 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. completedsr - 13.88 12 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.dsr-13.80 13 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade old work (two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface dsr-13.112.1 14 finishing walls with water proofing cement paint of required shade .( old work one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. ) dsr-13.109.1 15 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour .dsr-13.81 16 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old work dsr-13.99.1 17 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete. dsr-11.39 18 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complet size of tile 600x600 mm .dsr-14.41.2 19 providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of engineer-in-charge. with granite stone of area less than 0.50 sqm. dsr 16.86.1 20 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc.15 mm nominal dia pipes . dsr 18.8.1 21 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 25 mm nominal dia pipes . dsr 18.8.3 22 providing and fixing c.p. brass bib cock of pproved quality conforming to is:8931 : 15 mm nominal bore sor/dsr 18.49.1 23 providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 15 mm nominal bore sor/dsr 18.50.1 24 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15 mm nominal bore sor/dsr 18.53.1 25 providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931.15 mm nominal bore dsr 18.52.1 26 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. white vitreous china wash basin size 630x450 mm with asingle 15 mm c.p. brass pillar tap dsr 17.7.2 27 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests dsr 17.1.2 28 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredw.c. pan with isi marked white solid plastic seat and lid dsr 17.2.1 29 providing and fixing kitchen sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: 17.9.1 white glazed fire clay kitchen sink of size 600x450x 250 mm .dsr -17.9.1 30 providing and fixing t-iron frames for doors, windows and ventilators of mild steel teesections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).40x40x6mm@3.5kg/m . dsr 10.13.1 31 brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to is: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) . with f.p.s.(non modular) bricks .dsr-6.4.2 32 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in:: cement mortar 1:6 (1 cement : 6 coarse sand)dsr 6.1.2 33 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate dsr 11.3.1 34 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity - white .dsr-17.18.1 35 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr-18.48 36 earth work in excavation by mechanical means (hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by engineer-in-charge. all kinds of soil dsr 2.6.1 37 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). dsr 4.1.8 38 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter dsr12.41.2 39 renewing glass panes, with wooden fillets wherever necessary:float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) dsr14.6.1 40 cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 psi for sewer line from 150 mm dia upto 300 mm dsr 14.77 41 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) dsr 5.2.2 42 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo-mechanically treated bars of grade fe-500d or more.dsr 5.22a.6 43 centering and shuttering including strutting, propping etc. and removal of form work for : columns, piers, abutments, pillars, posts and struts.dsr 4.3.3

State Government

TRN :49023607 | 16 May, 2025

Tender Value : 22.62 Lacs

Lucknow - Uttar Pradesh

Tender for tender for construction and renovation work of community center located in sector-d of kanpur road scheme - rcc repairs 2 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge. 3 75mm average thickness 4 50mm average thickness 5 25 mm average thickness 6 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 7 bars upto 12 mm diameter 8 bars above 12 mm diameter 9 drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in rcc beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer-in-charge.upto and including 12mm dia. 10 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect.epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 11 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge.note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 12 25 mm average thickness in 2 layers. 13 50 mm average thickness in 3 layers. 14 providing and laying sbr polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structuralmembers e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of rcc member.note: rates shall be for finished surface area of concrete and shall include the cost of making holes in existing rcc slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved super-plasticiser forrendering concrete as flowable self compacting and sbr polymer but shall exclude cost of reinforcement, bond coat, shear keys, centering and shuttering, strutting, propping etc (payment under this item shall be madeonly after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) 15 50mm thick in grade m 25 with cement content not less than 330 kg per cum 16 75mm thick in grade m 25 with cement content not less than 330 kg per cum 17 100mm thick in grade m 25 with cement content not less than 330 kg per cum 18 providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge.(the payment shall be made on the basis of actual weight of approved grout injected.) 19 epoxy injection grout in concrete/rcc work of approved make 20 providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the engineerin- charge.wooven pvc cloth 21 shotcreting r.c.c. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stoneaggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by engineer- in-chargenote: rates shall include the providing necessary ground wires etc. the levelling gauges, if used, shall be paid for separately. payment under this item shall be made only after proper wet curing has been done and surface hasbeen satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 22 50mm thick in grade m 25 with cement content not less than 330 kg per cum 23 75mm thick in grade m 25 with cement content not less than 330 kg per cum 24 providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of engineer-in-charge. 25 providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 26 mild steel or iron work in plain work such as in r.c.c. or r.b. (when not included in an over all rates ) including bending for proper completion of the workand including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. 27 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 28 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 29 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thic 30 waterproofing and terracing 31 providing and laying in situ five course water proofing treatment with app (atactic polypropylene) modified polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to is : 702, 3rd layer of roofing membrane app modified polymeric membrane 2.0 mm thick of 3.00 kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron hmhdpe film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron hmhdpe film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 33 miscellaneous works 34 providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, includingadditional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia m.s. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with m.s. tubes, m.s. tube challis, m.s. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of engineer-in-charge.note:- (1) the elevational area of the scaffolding shall be measured for payment purpose. (2) the payment will be made once only for execution of all items for such works. 35 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. 36 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 37 cleaning of under ground sump, over head r.c.c. tank ( independent staging) including disposal of slit and rubbish, all as per direction of engineer-in-charge.the cleaning shall consist following operations:-(i) tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits.(ii) entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water.(iii) chlorination of rcc internal surface by liquid chlorine.(iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.(v) finally the surface shall be treated with ultraviolet radiation etc. as per direction of engineer-in-charge. 38 door-window repair 39 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) 40 renewal of old putty of glass panes (length) 41 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead asper direction of engineer - in- charge. 42 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer-in-charge. 43 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar 44 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres 45 casement door double panel with french (false) mullion with zinc alloy (zamak) 3d hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.using r4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above ) x (100 mm& above) & french (false ) mullion (64mm & above) x (60 mm & above). (height above 2.5 metre) 46 toughened glass 12 mm thickness 47 finishing work 48 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 49 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 50 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 51 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 52 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 53 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 54 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 55 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 56 washrooms 57 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 58 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 59 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including isi marked stainless steel butt hinges with necessary screws 60 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 61 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 62 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Local Bodies

TRN :49028253 | 15 May, 2025

Tender Value : 50.00 Lacs

Barmer - Rajasthan

Tender for supply of building material and equipment in gp barasan ps gudamalani-ghadla/kankar/jhajhra 2 mortar-soil/mud masala 3 lime from kali kiln for masonry work 4 cement 5 p.p.c. 6 white cement 7 fine aggregate 8 sand/gravel 9 fly ash 10 surkhi 11 stone dust (in masonry work) 12 ballast of stone/brick (for other than road work) 13 stone 40mm measured (grit broken by hand) (cut voids 1/11) 14 stone 40mm grit (broken by crusher) (cut voids 1/11) 15 stone 20mm grit (broken by crusher) 16 stone 12/10/6mm grit (broken by crusher) 17 brick ballast 18 material for road work (including 5 km lead) 19 63-40 mm stone crushed stone gravel (cut voids 1/11) 20 63-40 mm hand broken stone aggregate(cut voids 1/11) 21 90-45 mm. hand broken stone aggregate(cut voids 1/11) 22 quarry rubbish(cut voids 1/6) 23 gravel(cut voids 1/6) 24 kankar(cut voids 1/6) 25 binding material (pi 4-6)(cut voids 1/6) 26 brick (22.5 x 11 x 7.50 cm) 27 first class (i st class) 28 second class (ii class) 29 soling/ kharanja/ masonry stone 30 masonry beradda (rr) 31 masonry radda (cr) 32 kharanja soling (for flooring work upto 15cm height) 33 kharanja soling (for road/ kharanja work upto 23cm height) 34 jodhpuri type stone strips/arches/cuts (length 2-3, width 10-12,thickness 2.5-3.5) 35 stone chips (flaky material)(3-4 thick & length and width 1-2) 36 sandstone(dpc,sill,coping,lintel,tand,almirha etc) 37 upto 25mm thickness 38 upto 25-40mm thickness 39 upto 40-50mm thickness 40 upto 50-75mm thickness 41 upto 75-100mm thickness 42 upto 100-150mm thickness 43 flooring / patti pattan katla stone 44 flooring katla upto 35mm thick, min. 3 sqft or more area 45 patti pattan katla 60-75mm thickness, min. 3 sqft or more area 46 unpolished rough kota stone 47 900 sq. cm 48 upto 901 to 2300 sq. cm. 49 above 2300 sq. cm. 50 polished kota stone(one side polished) 51 upto 900 sq. cm. 52 upto 901 to 2300 sq. cm. 53 above 2300 sq. cm. 54 marble stone(makrana adanga 20mm thick) 55 upto 900 sq. cm. 56 upto 901 to 2300 sq. cm. 57 above 2300 sq. cm. 58 marble chips 59 marble powder 60 marble stone(rajnagar ii quality/local 20mm thick) 61 upto 900 sq. cm. 62 upto 901 to 2300 sq. cm. 63 above 2300 sq. cm. 64 stone frame 65 single paitaam size 100 x 75 mm. 66 double pattam size 125 x 75 mm. 67 stone plates 68 up to 1.5 m length, minimum 40mm thick 69 1.5 m to 2.40 m length, minimum 50mm thick 70 2.4 m to 3.0 m length, minimum 65mm thick 71 above 3.0 m length, minimum 75mm thick 73 glazed size-30x45 cm 74 mosaic size-40mm thick 75 vitrified size-60x60 cm 76 interlock tiles/brick/block for road work 77 cement interlocking block m-30grade, 60mm thick 78 cement interlocking block m-30grade, 80mm thick 79 cement interlocking block m-30grade, 100mm thick 80 fr pvc insulated copper conductor single core cable isi marked 81 1.50 sq. mm. 82 2.50 sq. mm. 83 0.50 sq. mm. 84 1.00 sq. mm. 85 4.00 sq. mm. 86 6.00 sq. mm. 87 local wood with fittings (for doors, windows and furniture) 88 mango 89 acacia 90 others 91 factory made doors (30mm thick, solid core single leaf) 92 structural steel 93 iron (tor steel fe 415/500 for reinforcement) 94 winding wire 18 gauge 95 iron girders 96 conical iron/ square bars/ leaf/ angle iron 97 barbed iron wire (size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage 98 mesh 99 iron mesh (24 gauge, 14 mesh) 100 cement concrete mesh akash patal 40mm thick 101 glass 102 3mm thick glass 103 colour paint 104 enamel paint 105 distemper (water bound) 106 lime - for whitewashing (aras / kali) 107 primer (for iron / wood) 108 petroleum products 109 diesel hsd 110 movil oil 111 bitumen shalitex board (25 mm thick) 112 plain sheet 113 g.i. sheet 22 gauge (0.80 mm) 114 g.i. sheet 24 gauge (0.63 mm) 115 m.s. sheet 22 gauge (0.80 mm) 116 m.s. sheet 24 gauge (0.63 mm) 117 corrugated sheet 118 g.i. sheet 1 mm thick 119 gi sheet 22 gauge(0.80 m.m.) 120 asbestos cement sheet 6mm(2.5/2.75x1m) 121 other sheets 122 pvc sheet 1mm thick (coloured/plain) 123 green yellow literof expo sheet(183x90) 124 pipes 125 gi 15mm diameter(b class) 126 gi 20mm diameter(b class) 127 gi 25mm diameter(b class) 128 a.c. 75mm diameter 129 a.c. 100mm diameter 130 p.v.c. 90mm diameter diameter(with ring) 131 pvc 110 mm. diameter(with ring) 132 pvc 140 mm. diameter(with ring) 133 pvc 110 mm.(2.5kg/sq.cm) with coupler 134 sanitary 135 indian w.c. 136 orrisa w.c. 137 european w.c. 138 foot rest 139 porcelain urinal 430350300 mm with coupler, bracket and pvc waste pipe 140 wash-basin 450*300 mm with coupler, bracket and pvc waste pipe 141 stone beam (s.w.) pipe 100 mm. diameter, 0.6 m. long 142 c.p. pillar cock (dia 15 mm) (is mark) 143 c.p. bib cock (dia 15 mm) (is mark) 144 c.p. grating of 125 mm. diameter 145 r.c.c. np3 hum pipe with collar 146 1200 mm dia 147 1000mm dia 148 750mm dia 149 600mm dia 150 450mm dia 151 300mm dia 152 steel conduit isi marked 153 20 mm. diameter 154 25 mm dia 155 charcoal 156 p.v.c. water tank with cover (conforming to is:12701-1989) 157 13/0.20 mm twin core pvc sheathed, flat flexible copper cable 158 steel fasteners 6 mm x 75 mm 159 pvc conduit isi marked 160 25 mm diameter 161 20 mm diameter 162 junction box 163 20 mm two way 164 20 mm one way 165 25 mm two way 166 20 mm one way (pvc) 167 module gi box 168 for 3 modules 169 for 2 modules 170 module base & cover plate 171 for 2 modules 172 3 for module 173 modular switch one way, isi marked 174 sp 15/16 ampere 175 sp 5/6 ampere 176 modular socket outlet, isi marked 177 3 pin 5/6 ampere 178 6 pin 15/16 ampere 179 mcb db 180 2+ 2 way, spn, single door 181 2+4 way, spn, single door 182 2+6 way, spn, single door 183 gi pipe (medium grade) 184 15.00 mm diameter 185 40.00 mm diameter 186 copper wire 8 swg (4.00 mm dia.) (0.117 kg/m) 187 ci/ms cover plate, frame with locking arrangement attached to 188 diesel road roller 8 to 10 ton 189 truck 9 ton 190 tractor (25-40 hp) 191 tractor trolley 192 tractor water tanker capacity 4000 liter water 193 cement concrete mixer 5-7 cubic feet 194 pumping set 15 h.p . 195 niddle/plate vibrator with operator 196 camel cart/bullock cart with driver 197 grinding machine with operator (big, motor driven) 198 compressor 199 hydraulic excavater/jcb ( bucket capacity 0.4 cum) 200 dumper 201 scraper 202 shuttering of wooden plank, with installing tp along with bat and other materials on site, removing it after the prescribed period 203 installing shuttering ply along with bat and other materials on tp site, removing it after the prescribed period 204 shuttering iron plate along with bat and other materials along with tp installation at site, removal after specified period 205 water and pumping charges (filling) 206 grinding machine with operator (small, hand operated) 207 installing iron form for well (diameter 3m, height 75cm) along with tp at site, removing after specified period 208 cultivator

Related Searched Keywords : ply board scrap

List of ply-board-scrap Tenders

Get ply board scrap Tender Alert...

Related Searched Keywords : ply board scrap

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us