Filters

List of steel-bin Tenders

List of latest steel-bin Tenders in Indian Tenders. Click on any steel-bin Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for steel-bin Tenders.

All-Tenders (172)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49057999 | 23 May, 2025

Tender Value : 0

Ghaziabad - Uttar Pradesh

Tender for tender for construction of civil works for increasing capacity from (1x500 plus 2x315 mva) to (2x500 plus 1x315 mva) at 400 k.v. sub-station-ist muradnagar ghaziabad. - earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) all kinds of soil including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by engineer-in-charge. 2 excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also includingramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all 3 providing and laying in position cement concrete of specified grade 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)excluding the cost of centering and shuttering - all work up to plinth level : 4 providing and laying in position cement concrete of specified grade 1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)excluding the cost of centering and shuttering - all work up to plinth level : 5 providing and laying in position cement concrete of specified grade1:1½:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 6 providing and laying in position specified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources), excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 7 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 8 centering and shuttering including strutting, propping etc. and removal of form for walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 9 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 10 centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts. 11 providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 12 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more. 13 brick work in foundation & plinth with old dismantled bricks (supplied by department free of cost) and coarse sand mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,t&p etc complete . 14 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand). 15 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). 16 dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks 17 supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer-in-charge . 18 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 19 mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof workgates etc. wrought to required form including holes rivetting or welding where necessary and also fixingin proper position and alignment but when steel is to be provided by the department . 20 12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand). 21 extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturers specification. 22 extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 23 neat cement punning 24 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 25 demolishing cement concrete (nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)) manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 26 demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. 27 dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 28 demolishing r.c.c. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars. 29 dismantling of existing pale / security / chain link fencing including post and stacking properly as per direction of the engineer - in - charge. including all labour and t&p etc. required for proper completion of the work 30 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 31 supply of 25 mm. dia m.s. anchor bolts (conforming to is 266)500 mm. long with base plate (50x50x6mm) welded with anchor boltsincluding its threading upto a length of 10cm. and also supplyof a pair of galvanized standard nuts with threading including supply of 5 mm thick washer and cost of labour, material & t&p for proper completion of work 32 fixing and grouting 25 mmand below dia m.s. anchor bolt in proper alignment level and setout with the help of a template including supply of all labour t&p etc. reqd. for proper completion of the work. (labour rates only) . 33 grouting of 90/105 lbs m.s. railincluding cost of all materials,labour & t&p for fixing of rail in proper alignment, leveland position in transformer plinth foundation etc. as perdirection of eng i/c. (rail to be supplied by thedept.)(labour rates only) . 34 s/f in position 105 lbs m.s. rail for transformer plinth including cost of all labour, material and t&p etc. required for proper completion of the work. 35 fixing and grouting of trench edging in proper level and alignment including cost of all labour, and t&p etc. required for proper completion of the work but excluding cost of c.c. (labour rates only) . 36 fixing of template in position level and alignment for groutingof anchor bolt in auxiliary gantry (labour rate only). 37 fixing of cable trench racks in proper position and alignment including cost of all labour, material and t&petc. required for proper completion of the work (labour rate only). 38 fabrication of template forauxiliary foundation including cost of all labour, and t&p etc. required for proper completion of the work. steel shall be arranged by contractor free of cost. this template shall be property of contractor.(labour rate only). 39 4.0 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm gradedapproved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement andmarble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels ifany and giving them a uniform finish including supply of all materials, labour and t&p etc, required forproper completion of the work. without base cc 40 placing of trench cover of all size in proper position including transportation from different places withinthe s/s area including all labour, t&p etc. required for proper completion of the work as per direction ofengineer - in - charge. 41 preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 42 providing and laying swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work (110mm dia pipe) 43 providing and laying design mix cement concrete of m-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy m.s. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of engineer-incharge (item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).cement concrete manufactured in automatic batching plant (rmc plant) i/c transportation to site in transit mixer 44 providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood pre-laminated one side decorative lamination and other side balancing lamination grade i, type ii, is : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete : (12mm thick partical board) 45 hiring of beldar(labour).

State Government

TRN :49059485 | 31 May, 2025

Tender Value : 70.47 Lacs

Vrindavan - Uttar Pradesh

Tender for tender for construction of rotary at different nodes-1, 2, 3 and 4 at vrindavan yojna, lucknow. - bituminous workdismantling of flexible pavements and disposal of dismantled materials upto a lead of 100 m, stacking serviceable and unserviceable materials separately as per technical specification clause 202. 2 providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical meansincluding supply of all materials, labour t&p etc. required for proper completion of the work as per mort&h specificationno. 502 (5.1)and as per dierction of the engineer in charge. 3 providing & laying dense graded bituminous macadam with hot mix 100-120 tph hot mix plant producing an average out put of 75 tonnes per hourusing crushed aggregate of specified grading, premixed with bituminous binder,@ 4.0 to 4.5 % weight of total mix and fillertransporting the hot mix to work site, laying with hydrostaticpaver finisher with sensor controller to requiredgrade, level & alignment & rolling with smooth wheeled vibratory and tandem rollers to achieved the desired compaction complete in all respects & as per relevant clauses of mort & h section-507 (vg-30) 4 providing & applying tack coat with bitumen vg-10using bitumen pressure distributor at the rate of 0.35kg/sqm on theprepared bituminous/granular surface cleaned with mechanical broomincluding supply of all materials, labour t&p etc. required for proper completion of the work as per mort&h specification and as per dierction of the engineer in charge. 5 providing & laying bituminous concrete 30 mm withhigher capacitybatch type hot mix plant producing an average out put of 75 tonnes per hourusing crushed aggregate of specified grading, premixed with bituminous binder,@5.4% weight of total mix and fillertransporting the hot mix to work site, laying with hydrostaticpaver finisher with sensor controller to requiredgrade, level & alignment & rolling with smooth wheeled vibratory and tandem rollers to achieved the desired compaction complete in all respects & as per relevant clauses of mort & h section-507 6 providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 grms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35. the finished surface to be level, uniform and free from streaks and holes. 7 supply and fixing of pavement marker (cat eye) type x - astmd - 4956 - 04 avey dennison / 3 - m (usa make) consisting of asa plastic housing fitted with lightly adherent ploting compound. the housing cell contain prismatic two glass covered presmatic reflective fase to reflect incident light. (rpm with shank as per astm. dar 8.35 8 supply and fixing of monument forrotary including supply of all materials labourt & petc. required for proper complition of the work and as per direction by e/i. (m. r.) 9 retro-reflectivesheeting type-iv with 4 mm thick acm double side:providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with high intensity prismatic sheeting type iv as per irc-67:2012 retro reflective sheeting with back frame ms angle of 35x35x5 mm. legends, letters, numerals and borders etc should be as per morth specification no-801.3.7 the sheeting shall have a pressure sensitive adhesive of the aggressive-lack type requiring no heat. solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer. the acm (aluminium composite materials) shall be fixed on the back frame ms angle with riveting. micro prismatic type iv retro reflective sheeting confirming to astm d4958-09 shall be pressure fixed. the retro reflective sheeling shall be lested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international government laboratory/ iristitute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. aternatively, a certificate conforming to astm specification (d) 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally, in such a situation, the employer/client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67:2012 & proof of the same report shall be uploaded which quoting tender. the rate shall include all materiais, labour, t&p, transportation, installation and incidentals all complete as per direction of the engineer-in-charge. uppwd sor 2020-21 ch-26 s.i. no. 11 ref mort&h-801 10 providing and laying of trapezoidal hump/table top speed breaker as per drawing/design including all material, labour, t&p etc complete as per direction of e/i. 11 circular rotary and triangular islandearth work in surface excavation not exceeding 30cm in depth but exceeding 1.5m in width as well as 10sqm.on plan including getting out and disposal of excavated earth upto 50m and lift upto1.5m as directed by e/i. (uppwd sor s.i. no. ch.-7 s.l.-1 ref. dar 2.6.1)0.30m and above 12 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement, 4 coarse sand and 8 graded stone agreegate 40mm nominal size). (uppwd sor chap- 8, si no 1, ref to dar 4.1.8) 13 centering and shuttering including strutting, propping etc. and removal of form work for: foundations, footings, bases for columns(uppwd sor chap- 8, si no 3, ref to dar 4.3.1) 14 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto plinth level 1:1.5:3 (1 cement, 1.5 coarse sand and 3 graded stone agreegate 20mm nominal size). (uppwd sor chap- 8, si no 1, ref to dar 4.1.2) 15 m.s.iron work in plain work such as reinforced concrete or reinforced brick work wrought to required shape as necessory including bending for proper completion of the work. and including supply of steel its wastage bend hooks and authorised overlapping shall be measured. 16 finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade :new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg /10 sqm )(apex ultima weather coat all guard ) asian, berger also including providing and applying white cement based putty of averge thickness 1 mm of approved brand over the plasterd surface to prepare thesurface even and smooth complete as per direction by e/i. 17 providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, ivc fixing the railing with necessary accessories & stainless steel dash fasteners stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 18 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth, consolidation each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m. (uppwd sor s.l. no. 4 ref dar 2.25) 19 providing and laying of interlocking concrete block pavement having thickness 80mm as per drwaing and technical specification clause-1504 including earth work in excavation of required depth and width, providing, laying and compacting of w.m.m. and local sand for cussion of tiles etc also including supply of all material, labour, t&p etc complete.

State Government

TRN :49059519 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for baidyapur water supply scheme, t.w. no. iv, block: tarakeswar, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059524 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for solepur duttapur water supply scheme, t.w. no. iv, block: tarakeswar, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059541 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for rajhat water supply scheme (uncovered area), t.w. no. xi, block: polba dadpur, district - hooghly under electrical division, phe dte- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059545 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for sibrambati water supply scheme, zone-i, t.w. no. iii & iv, block: singur, district - hooghly under electrical division, phe dte.- part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 for t.w. no. iii 37 for t.w. no. iv 38 add: 18% gst 39 add: 1% cess

State Government

TRN :49059552 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for kaknan water supply scheme, t.w. no. iv, block: khanakul-ii, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059555 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for refaitpur water supply scheme, zone-i, t.w. no. iii, block: chinsurah mogra, district - hooghly under electrical division, phe dte- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059565 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for raghubati water supply scheme, t.w. no. iii & iv, block: goghat-i, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 for t.w. no. iii 37 for t.w. no. iv 38 add: 18% gst 39 add: 1% cess

State Government

TRN :49059624 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for jagatpur water supply scheme, t.w. no. vi, block: khanakul-ii, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

Related Searched Keywords : steel bin

List of steel-bin Tenders

Get steel bin Tender Alert...

Related Searched Keywords : steel bin

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us