Filters

List of steel-pole Tenders

List of latest steel-pole Tenders in Indian Tenders. Click on any steel-pole Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for steel-pole Tenders.

All-Tenders (109)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

corporations/Associations/Others

TRN :49022685 | 10 May, 2025

Tender Value : 10.32 Lacs

Kanpur - Uttar Pradesh

Tender for tender for 29-construction of entrance gate in gram panchayat bhaura block-sumerpur - steel work in built up tubular (round hollow tubes ),trusses etc. including cutting ,hoisting ,fixing in position and applying a priming coat of appd. steel primer including welding and bolted with special shaped etc. comp. in all respect hot finished seamless type tubes /pole dsr code no 10.16.2 2 s/f of 25.00mm long steel polished screw with washer 3 painting work with three coat of appd. synthetic enamel paint with one coat of primer 4 construction of r.c.c. foundation size 1.80x1.80mtr. and 1.80 mtr deep for builtup overhead structure including earth work in execavation 150mm thick lean concrete in 1:4:8 cement and coarce sand and 40mm gauge stone ballast r.c.c. with 1:1.5:3 cement ,coarse sand and 20mm stone grite including supply and groutingnof 25mm dia foundation bolt(600mm longas per provision of structure including cost of reinforcement and shuttering including all material ,labour t&p etc. required for proper completion of work including cartage up to site and all taxes labour cess etc. all complete work as per direction of e/i earth work in execavation in foundation by mech. means dsr code no 2.6.1 5 sand filling in foundationdsr code no 2.27 6 lean concrete in 1:4:8 infoundation dsr code no 4.1.8 7 r.c.c. 1:1.5:3 in foundation up to ground level dsr code no 5.1.2 a 8 reinforcement 2% of r.c.c. dsr code no 5.22a.1 9 trasportation .labour charges, t&p such as hydra and other tools etc. 10 providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 04 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with high intensity prismatic sheeting type iv as per irc 67 2012 retro reflective sheeting with back frame ms angle of 35x35x5 mm. legends, letters, numerals and borders etc should be as per morth specification no-801.37 the sheeting shall have a pressure sensitive adhesive of the aggressive-tack type requiring no heat solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer the acm (aluminium composite materials) shall be fixed on the back frame ms angle with riveting. micro prismatic type iv retro reflective sheeting (confirming to astm d4956- 09 shall be pressure fixed the retro reflective sheeting (shall be tested for a certificate or having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility liner removal, adhesion, impact resistance, specular gloss and fungus resistance meeting the requirement of three years outdoor weathering of the sheeting as per irc 67-2012 & proof of the same report shall be uploaded which quoting (tende: the rate shall include all materials labour t&p transportation, installatic and incidentals all complete as per direction of the engineer-in-charge morth 801 s.i. no 11 lucknow sor

Local Bodies

TRN :49022842 | 16 May, 2025

Tender Value : 8.07 Lacs

Raebareli - Uttar Pradesh

Tender for tender for construction work of 04 m.m.i.g. buildings in amol vihar yojna - earth workinfoundation in ordinary soil ( loamclay,or sand) including lift upto 1.5 metre ( 5fts) and lead upto 30m. (100fts.)andincludingfilling watering and raming of excavatedearthintotheplinth and removal anddisposalof surplus earth and directedby the engineer - in - chargeupto a distance of 30m. ( 100 fts ) from the foundation trenches. 2 earth work in cutting or in embankment in ordinary soil, excavation to be in form of regularpitsnotexceeding1/2 mt (20) in depth and earthwork inembankmenttobein20cm (8) layers, including ramming anddressingthesurfaceto requiredlevelsandslopesand alsoincluding1.5mts(5fts)lifts and 30mt (100fts) lead. the earth from cutting to be used in makingembankmentsortobe deposited as spoil banks with in30mts(100fts)distanceas directedbytheengineerin charge,includingcartageof8km. 3 concrete with4cm. (1*1/2) gauge brick ballast, fine local sand of 1.25 fineness modulous andcementin proportion of 8: 4:1infoundationsand under floors, includingsupply of allmaterials,labourand t&p etc.requiredforpropercompletion of the work. 4 providingandlayinginposition specified grade of reinforced cement concrete, excluding cost of centering, shuttering, finishing and reinforcement in 1: 11/2 : 3 ( 1 cement, 11/2 coarse sand , 3 20mm graded stone aggregate. 5 foundations,footings,basesof columns, etc. for massconcrete 6 columns,pillars,piers,abutments, posts and struts 7 suspended floors, roofs, landings, balconies and accessplatform 8 mildsteelorironinplain worksuchasreinforced concreteorreinforced,brick work(when notincluded inan over all rates ) wroughtto required shapeasnecessary includingbendingforproper completion of the work and including supply of steel its wastagebendhooksand authorised over lapping shallbemeasured. 9 brick work in comman burnt clay (non-modular)bricks of class 150 in super structure aboveplinthlevelincluding supplyoflabour,materialand t&prequiredforproper completionofworkincement mortar 1:6 ( 1 cement: 6 coarsesand) 10 class150 brick work in1:4 cementand coarsesand mortarinsuper - structureforwallthickness 12 cms 11 12mmthickcementplasterof mix1:4(1cement:4coarsesand) 12 providing &layingof lightcinderfillingunderfloorof toilets & other sunken roofs. 13 providingandfixinginwall unplasticisedrigidpvcrain waterpipesconformingtois: 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermalexpansion,(i)singlesocketed pipes. 110 mm dia 14 providingwoodworkinframe ofdoors,windows,celerestory windowsandotherframes, wrought frames and fixed in positionwithholdfastlugsor withdashfastnersofrequired dia and lenghts (hold fast lugs or dashfastnersshallbepaidforseperately): sal wood 15 providingandfixingangleiron framesfordoors,windowsand ventilatorsofmildsteelangle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing t- ironframeortothewallwith dash fastener, including fixing of necessary butt hinges and screwsandapplyingapriming coatofapprovedsteelprimer, all complete as per the direction ofengineer-in-charge.(fordoorframes) 16 providingandfixingisimarked flush door shutter confirming to is:2202(part1)non-decorative type, core of blockboard constructionwithframeoffirst classhardwood andwell matched commercial 3 ply veneering with vertical grains or cross bands and face vineers on both facesof shutters:35mm thick including isi marked stainlesssteelbutthingeswithnecessary screws. 17 providingandfixingwiregauge shutterusinggalvanisedms wiregaugeofaveragewidthof apurture1.4mminboth directionwithwireofdia 0.63mm for doors, windows and celestorywindowswithhinges and necessary screws. 35mm thick shutter, with isi marked mspressedbutthingesbright finished of required size withsecond class teak wood. 18 steelworkweldedinbuiltup sections/framedwork, including cutting, hoisting, fixing inpositionandapplyinga primingcoatofapprovedsteel primer using structural steel etc. asrequired.ingratings,frames, guard bar, ladder, railings, brackets,gatesandsimilarworks(forwindow grills) 19 providingandfixingaluminium towerbolts,isimarked, anodised (anodic coating not lessthangradeac10asper is:1868) transperent ordyed to required colour or shed, withnecessary screws etc. complete. 150 x 10mm+ 20 250 x 10 21 providingandfixingaluminium sliding door bolts, isi marked anodised anodic coating not less thangradeac10asperis: 1868),transparentordyedto requiredcolourorshade,with nutsandscrewsetc.complete:250x16 mm 22 providingandfixingaluminium hangingfloordoorstopper,isi markedanodised(anodic coatingnotlessthangradeac-10asperis:1868)transparent ordyedtorequiredcolourand shed, with necessary screws etccomplete. twin rubber stopper. 23 mildsteelorironwork of heavy sizes and sections such as holdingdownbolts,holdfast, tie, rods gratings etc (when not included in an over all rates) wrought to required form, includingsupplyofsteel,bolts, nutsandwastageetcandtheir fixingrequiredtoproper completionofwork.(fortubular stair case railing) 24 providingandlayingvitrified floortilesindifferentsizes (thickness to be specified by the manufacturer) with water absorptionlessthan0.08%and conforming to is : 15622, of approved make, in allcolours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarsesand),includinggrouting the joints with white cement and matching pigmentsetc.,complete. size of tile 600x600 mm 25 providingand laying vitrified tilesin differentsizes (thickness tobespecifiedby manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in allcolours &shade,inskirting,riserof steps,over12mmthickbedof cement mortar 1:3 (1 cement: 3 coarsesand),includinggrouting thejointwithwhitecement& matching pigments etc.complete. size (600x600) 26 marblestoneflooringwith18 mmthickmarblestone,asper sampleofmarbleapprovedby engineer-in-charge, over 20 mm (average)thickbaseofcement mortar 1:4 (1 cement : 4 coarse sand) laid and jointedwith grey cement slurry, including rubbingand polishing complete with : udaipur green marble 27 providingandfixingfirstquality ceramic glazed wall tile confirmingtois:15622 (thickness to be specified by the manufacturer)ofapproved makeinallcolours,sheds exceptburgandy,bottlegreen, black of any size as approved by engineerincharge,inskirting, rizersofstepanddados,over 12mmthickbedofcement mortar1:3(1cement:3coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mix with pigment ofmatching shed complete. 28 providing and laying ceramic glazed floor tiles of size 300x300 mm(thicknesstobespecified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours suchaswhite,ivory,grey, fume red brown, laid on 20 mm thickcementmortar1:4(1 cement : 4 coarse sand), includingpointingthejoints with white cement and matchingpigment etc, complete. 29 providing and applying white cementbasedputtyofaverage thickness1mm,ofapproved brand and manufacturer, over the plastered wall surface to prepare the surface even andsmooth complete. 30 finishing walls with acrylic smoothexteriorpaintof required shade on new work (twoormorecoatapplied@1.67ltr/10sqmoverand includingprimingcoatof exterior primer applied @ 2.20kg/ 10 sqm) 31 wallpaintingwithacrylic emulsionpaint,havingvoc (volatile organic compound ) content less than 50 grams/ litre, of approved brand and manufacture,includingapplying additional coats wherever required, to achieve even shadeand colour. two coats 32 paintingwithsyntheticenamel paint of approved brand and manufactureofrequiredcolour togiveanevenshade:twoor morecoatsonnewworkover an undercoatofsuitable shade with ordinary paint of approvedbrand and manufacture 33 providing and fixing white vitreouschinapedestaltype water closet (european type) withseatandlid,10litrelow level white vitreous china flushingcistern&c.p. flush bend with fittings & c.i.brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proofcouplingofapproved municipaldesigncomplete, including painting of fittings and brackets, cutting and making good thewallsandfloorswherever required : w.c. pan with isi markedwhitesolid plastic seat and lid 34 providingandfixingwashbasin withc.i.brackets,15mmc.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making goodthewallswhereverrequire: whitevitreouschinawash basin size 630x450 mm with a pairof15mmc.p.brasspillartaps 35 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittingscomplete. semi rigid pipe 32 mm dia 36 providing and fixing cp brass bibcock of approved quality confirming to is: 8931 15mm nominal bore. 37 s/f of 15mm nominal bore cpvc pipe all complete. 38 providing and fixing cp brass angle valve for basin mixer and geyser points of approved quality confirming to is:8931 15mm nominal bore. 39 15mm nominal boare 40 providing and fixing cp brass shower mixer of 15 or 20mm bore including cp brass connection with angle valve of standard design and approved make confirming to is:8931 41 providing and fixing cp brassover head shower with 15 or 20 mm inlet including connection complete: 100mm diameter. 42 providing and fixing trap of selfcleansing design with screwed down or hinged grating with or with out vent arm complete, including cost of cutting chases and making good the walls and floors:100mm inlet and 100mm out let pvc 43 100mm inlet and 75mm outlet pvc 44 providing and placing on terrace (at all floor levels) polyethylene water storage tank, isi : 12701 marked, with cover and suitable locking arrangement andmaking necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 45 providing, fixing and jointing pvc pipes of different diameters with with pvc solvent cement (or as per manufacturers specifications) with or without sockets (if sockets are provided with pipe length) in vertical sewage line, waste water line and vent line with all necessary bends, angle bends, tees, elbows ms bat clamps along with all necessary fastners and bolt with cutting chases and making good the walls and floors wherever required including testing of the same all as per direction and satisfaction of engineer in charge.6kg per sqin pressure pipe75mm inner dia. 46 6kg per sqin pressure pipe110mm inner dia. 47 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, including fixing the pipe with clamps 1.00m spacing. this includes jointing the pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. 15mm nominal outer dia pipes. 48 25mm nominal outer dia pipes. 49 constructing masonary chamber 30x30x50cminside,inbrick workincementmortar1:4(1 cement:4coarsesand),with ci surface box 100x100x75 mm(inside)withhingecover fixed in cement concrete slab 1:2:4 ( 1 cement : 2 coarse sand:4 graded stone aggregate 20mm nominal size) including necessary excavation, foundationconcrete1:5:10(1cement:5finesand:10graded stoneaggregate40mmnominal size)andinsideplasteringwith cement mortar1:3 ( 1 cement : 3coarsesand)12mmthick, finishedwithafloatingcoatof neat cement complete as perstandard design: 50 supply delivery errection the fabricatedmsboardofsuitable sizeonwhichthefollowing supplieditemsshallbefixedas per the direction of enggincharge. 51 (a)supply and fixing 63 ampdoublepole(singlephase &neutral)240voltresidual currentcircuitbreakerrccb havingasensivitycurrentup to300 ma on the existing ms board complete with connection testing&commissioningetcas required. 52 (b)supplying & fixing 2+8way single door prewired sp&n mcb distribution board of sheet steel for240voltonexistingms board complete with dpmcb isolator40amp240volt1no& 25amp single pole240 volt spmcb(c)series5nos completeduly wired with 4sqmm fr pvc insulated copper conductorupto terminal box tinned copper busbar ditachable gland plate, inter connection phosphotized &powder coated includingearthingetcasreq( for power distribution ) 53 (c)supplying & fixing 2+8way single door prewired sp&n mcb distribution board of sheet steel for240voltonexistingms board complete with dpmcb isolator40amp240volt1no& 10amp single pole240 volt spmcb(c)series5nos completeduly wired with 4sqmm fr pvc insulated copper conductorupto terminal box tinned copper busbar ditachable gland plate, inter connection phosphotized &powder coated includingearthingetcasreq( for light distribution ) 54 wiring point for lightwith 1.5sq mmfrpvcinsulated multistrandsinglecorecopper conductorcableinpvcconduit concealedinthewallcomplete with modulartype switch &ceilingrose/angle/batten holderon3mmthickphenolic laminated backalite sheet etc comp in all respect 55 wiringpointforfan 1.5sq mmfrpvcinsulated multistrandsinglecorecopper conductorcableinpvcconduit concealedinthewallcomplete with modulartype switch &ceiling roseon3mmthick phenolic laminated backalite sheet &fan boxetccompin all respect 56 wiringpointfor freshairfan with 1.5sq mmfrpvc insulated multistrandsinglecorecopper conductorcableinpvcconduit concealedinthewallcomplete with modulartype switch &ceiling roseon3mmthick phenolic laminated backalite sheetetc comp in all respect 57 supply&fixing5ampmodular switch & 5amp 5pin modular socketontheexistingmodular plateandswitchboxincluding connection etc as reqd. 58 supply&fixingofpowerplug 20amp250voltflushtype modular switch& 5pin 20amp 250voltmodular socket on concealedmsbox etc.asrequered 59 supply & wiring for power pointwith2no4sqmmfrpvc insulated1100voltgrade multistrandsinglecorecopper conductor cable in 20mm dia heavydutypvcconduitwith1 no2.5sqmmfrpvcinsulated multistrandcopperconductor cable as earth continuity wire in conduit etc as required 60 wiringofcircuitalongwith earth wire with the following size of fr pvc insutated copper conductorsinglecorecablein recessed medium class 20mm dia pvc conduit as required 61 1x1.5sqmm+1x1.5sqmm 62 supply & fixing of electronic fan regulatormodular400w 120v-- 280v isi marked on existing switchboard includingmaking connection etc for proper completion of work 63 supply&burryingofsafe earthingelectrodet-19zn-zinc coated,lengthupto3000mm, outer pipe 48.4mmx3.2mm, inner pipe 26.9mmx2.6mm, terminaldia12mm,coating80- 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc)capable of reducingthe soilresistivitywith good mixture of retaining capacityandoneearthinglead of 20mmx3mmg.i. strip,up to switch board (from apron to switchboard,thecostofg.i. strip will be extra)along with 30cm square c.i. frame with hinged cover & masonary housing 64 supplying&layingof 20mmx3mm g.i. strip directly in ground&onwallasrequired complete in all respect (from apron to switch board. 65 wiring for submain withthe 2x10sqmm size fr pvc insulated copper conductor cable in recessedmediumclasspvcconduit as required 66 boring with hydraulic piling rigs with power units, providing and installingcastinsitusingleunder reamedpilesofspecifieddiameter andlengthbelowpilecapinm-25 cementconcrete,tocarryasafe working load not less than specified, excluding the cost of steel reinforcement but including thecostofboringwithbentonite solutionandthelengthofthepile to be embedded in pile cap etc. all complete.(lengthofpilefor payment shall be measured upto tothe bottom of pile cap) : 300 mm dia piles 67 s/f of kitchen sink including all labour and t&p all complete. 68 15mm thick plaster in 1:4 (1 cement and 4 coarse sand) including all labour complete. 69 s/f of gate valve including all labour and t&p all complete 70 s/f pvc bulb holder including all labour and t&p all complete 71 s/f aluminium door handle including all labour and t&p all complete 72 s/f of chequered tiles on ramp of house including all labour and t&p all complete 73 s/f flange bib cock with z spray including all labour and t&p all complete 74 s/f of kota stone on rear court yard anf front porch of house including all labour and t&p all complete 75 s/f of granite stone on kitchen top of house including all labour and t&p all complete 76 s/f of basin mixture including all labour and t&p all complete 77 s/f of 25mm cpvc pipe including all labour and t&p all complete

corporations/Associations/Others

TRN :49023085 | 10 May, 2025

Tender Value : 10.32 Lacs

Kanpur - Uttar Pradesh

Tender for tender for 27-construction of entrance gate in gram panchayat pachkhura block-sumerpur - steel work in built up tubular (round hollow tubes ),trusses etc. including cutting ,hoisting ,fixing in position and applying a priming coat of appd. steel primer including welding and bolted with special shaped etc. comp. in all respect hot finished seamless type tubes /pole dsr code no 10.16.2 2 s/f of 25.00mm long steel polished screw with washer 3 painting work with three coat of appd. synthetic enamel paint with one coat of primer 4 construction of r.c.c. foundation size 1.80x1.80mtr. and 1.80 mtr deep for builtup overhead structure including earth work in execavation 150mm thick lean concrete in 1:4:8 cement and coarce sand and 40mm gauge stone ballast r.c.c. with 1:1.5:3 cement ,coarse sand and 20mm stone grite including supply and groutingnof 25mm dia foundation bolt(600mm longas per provision of structure including cost of reinforcement and shuttering including all material ,labour t&p etc. required for proper completion of work including cartage up to site and all taxes labour cess etc. all complete work as per direction of e/i earth work in execavation in foundation by mech. means dsr code no 2.6.1 5 sand filling in foundationdsr code no 2.27 6 lean concrete in 1:4:8 infoundation dsr code no 4.1.8 7 r.c.c. 1:1.5:3 in foundation up to ground level dsr code no 5.1.2 a 8 reinforcement 2% of r.c.c. dsr code no 5.22a.1 9 trasportation .labour charges, t&p such as hydra and other tools etc. 10 providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 04 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with high intensity prismatic sheeting type iv as per irc 67 2012 retro reflective sheeting with back frame ms angle of 35x35x5 mm. legends, letters, numerals and borders etc should be as per morth specification no-801.37 the sheeting shall have a pressure sensitive adhesive of the aggressive-tack type requiring no heat solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer the acm (aluminium composite materials) shall be fixed on the back frame ms angle with riveting. micro prismatic type iv retro reflective sheeting (confirming to astm d4956- 09 shall be pressure fixed the retro reflective sheeting (shall be tested for a certificate or having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility liner removal, adhesion, impact resistance, specular gloss and fungus resistance meeting the requirement of three years outdoor weathering of the sheeting as per irc 67-2012 & proof of the same report shall be uploaded which quoting (tende: the rate shall include all materials labour t&p transportation, installatic and incidentals all complete as per direction of the engineer-in-charge morth 801 s.i. no 11 lucknow sor

Co-operative

TRN :49023911 | 20 May, 2025

Tender Value : 0

Powayan - Uttar Pradesh

Tender for supply of general electrical items for season 2025-26 , description , remote bell , tong tester meco make 1000 amp a.c./d.c. , manual control fan regulater 4 steps, single module , mcb din rail channel, 35mm width , air heater heating element 1 meter single , amp.meter 4x4 ,0 - 600 amp ctr 600/5 , amp.meter 4x4 ,0 - 800 amp ctr 800/5 , amp.meter 4x4 ,0 - 1000 amp ctr 1000/5 , amp.meter 96x96mm , ctr 100/5 , amp.meter 4x4 ,0 - 50 amp ctr 50/5 , amp.meter 4x4 ,direct 0-10 amp & 0-20 amp , amp.meter 96x96mm, 150/5 , amp.meter 4x4 , 300/5 , amp.meter 4x4 , 400/5 , ct 50/5,60/5,100/5,150/5,300/5,400/5,600/5,500/5 , ct ae make 1000/5 , piller assambly for 800 amp , ct630/800 amp for acb , operating handle on/off 800 amp , dn 1 release , cable tie 4 , cable tie 6 , soldring paste , change over switch 400 amp in ss hpl /sucomake , indicator led 220 volt red , volt.meter 4 0 - 500 volt , contactor 6 way 30 amp. l&t/schneider/switch gean , amp. meter 0 - 15 amp 4 , amp. meter 0 -160 amp 4150/5 a/e / rc , power contactor 3ta22 230 volt , mcb single pole 32 ampschneider /l&t / abb , mcb double pole 16 amp schneider /l&t / abb , mcb double pole 20 amp schneider /l&t / abb , mcb dboule pole 32 amp schneider /l&t / abb , mcb triple pole 16 amp schneider /l&t / abb , mcb triple pole 20 amp schneider /havells , mcb triple pole 32 amp schneider /havells , mcb triple pole 63 amp schneider /havells , distribution board 12 way spn (mcb box) schneider /havells , digital energy meter 3 phase 4 wirectr 200/5 l&t , transfarmer 1 kva 230 volt , sambersibleflexible flat copper cable (35mm x3 core) , change over switch 800 amp 4 pole hewlls make l&t , change over switch 400 amp 4 pole hewlls make l&t , pvc copper cable660/1100 volt for unloder 1.5mm 16 core , carbon bush 50x32x32 usha/bosch , volt meter 4 0-100 volt a/e , oil resistance box 250 hp rb450 ra 146 oil immersed , dinodrive electronic controllereddy current control , pvc copper flat sambersible cable 6mm 3 core , electronic blower wolf make /eastman , spray gun h.duty , digital rpm meter 0-500 rpm wantran , fuse base nsh 20 amp , indicating lamp 240 volt complete hack/jigo , push button element 1 no , push button element 1 nc , mcb box 4 pole l&t , indicating lampr y b , piston drill machine complete wolf make bosh , hand lamp , push button element 1 no+1nc teknic , ct 30/5 , pvc coolling fan 5 hp 1440 rpm ke make simenss , pvc coolling fan 7.5 hp 1440 rpm ke make simenss , pvc coolling fan 10 hp 1440 rpm ke make simenss , motor fan cover ke make 5 hp 1440 rpm ke/ simenss , motor fan cover ke make7. 5 hp 1440 rpmke/simenss , motor fan cover ke make 10 hp 1440 rpm ke/simenss , allu. imhibiting crosen cable compound ke/simenss , hydraulic cable crimpingmachine upto 400 mm complte taparia , hydrauliccable crimping machine upto 95 mm compltetaparia , p t bulb 24 volt , slipring 90 hp 67 kwframe size lcw 250 , slipring250 hpframe size rw 10539 , slipring250 hp1480 rpm , carbon brush holder90hp lcw 250 , carbon brush holder150 kw rw 10539 , carbon brush holder370kw , spare for oil immersed star delta starter , a- moving arching contact with guttka , b- fix finger contact big , c- fix finger contact small , amp meter 72x72mm 30/5 , amp meter 72x72mm 100/5 , cannector element 35mm , connector element 50mm jigo/rc , connectorelement 70mm , electronic timer 415 volt 36-120 secd. simenss /l&t , g.i.g.o.l. varnised crodium nut & bolt with washers , ………………………………do…………………………….12x50mm , ………………………………do…………………………….10x50mm , ………………………………do…………………………….8x50mm , ………………………………do…………………………….6x50mm , ………………………………do…………………………….12x65mm , ………………………………do…………………………….10x65mm , ………………………………do…………………………….8x65mm , ………………………………do…………………………….6x65mm , ………………………………do…………………………….12x75mm , ………………………………do…………………………….10x75mm , ………………………………do…………………………….8x75mm , ………………………………do…………………………….6x75mm , drill machineh.duty bosch , v.s.f. treding tape 1/4 , v.s.f. treding tape 1/16 , v.s.f. treding tape 3/8 , v.s.f. treding tape 1/2 , v.s.f. treding tape 5/8 , v.s.f. treding tape 3/4 , control transfarmer input 415 volt a.c. output 230 volt d,.c. 0.5 kva wnton,gromption , geyser 25 ltr gromption/havells , change over switch 250 amp ss havells/l&t , cooling fan 75 hp bharat bijli/simenss , cooling fan 60 hp bharat bijli/simenss , cooling fan 40 hp bharat bijli/simenss , cooling fan 15 hp bharat bijli/simenss , cooling fan cover 75 hp ke make simenss/bharat bijli/kirloskar , cooling fan cover 60 hp ke make simenss/bharat bijli/kirloskar , cooling fan cover 10hp ke make simenss/bharat bijli/kirloskar , terminal plate 75 hp ke makesimenss/bharat bijli/kirloskar , terminal plate 7.5 hp ke make simenss/bharat bijli/kirloskar , terminal box 15 hp 160 kh simenss/bharat bijli/kirloskar , terminal box 7.5 hp kh 132simenss/bharat bijli/kirloskar , carbon brush 16x32x38 jyoti/bosch , carbon bush 10x22x38 , carbon brush 20x40x50 , carbon holder jyoti make jyoti , copper rod 1.5x18,long , g.i.g.o.l. varnised crodium nut & bolt with washer---- , …………………………..do………………………….16x50 , …………………………..do………………………….16x75 , …………………………..do………………………….18x50 , …………………………..do………………………….18x75 , …………………………..do………………………….15x50 , …………………………..do………………………….15x75 , …………………………..do………………………….15x26 , …………………………..do………………………….12x25 , …………………………..do………………………….10x100 , …………………………..do………………………….12x100 , …………………………..do………………………….10x20 , …………………………..do………………………….10x25 , …………………………..do………………………….8x25 , …………………………..do………………………….6x25 , mcb box3 pole havells /anchor , hrc fuse tia 32 amp simens/l&t , hrc fuse tis 63 amp simens/l&t , terminal plate 60 hp ke/simens/bhart bijli , cooling fan 3 hp , slipring resistance box 3 step 7.5 hp r v 140-170 volt , slipring resistance box 3 step 10 hp r v 206 volt , highvoltage syenthetic insulation electric make suitable for , upto 33 kv isi 15652 thk 12mm length 1x2 mtr , spare for 300 amp ocb------ , a- moving arching contactl typetulip/ , b- v bar , c- fix arching contact , d-fix moving contact , amp.96x96mm direct 0-15,amp , ct 90/5ae/l&t , infrared thermo meter max.output1mm 670 mm lenth ledger type , ct 120/5 ae/l&t , ct 180/5 ae/l&t , indicating light lead red 220voltjigo/ae , terminal plate 10 hp , overload reley 25-40 amp simens , stater for 150 hp /110 kw sliparing motor with housing , slipring resistence box 3 step 150 hp r v 330 volt oil immersed , archute 800 ampl&t , amp.meter 120/5 ae/rc/jigo , amp.meter 180/5 ae/rc/jigo , d.spanner set taparia , ring spanner set , box spanner set , contimoty tester with cell , indicating bulb 7 watt 20 volt , change over switch onload 630 amp in ss 4 pole hewlls/semens , auxillary contanct block 3ta24/3ta28 , hexa blead fram h.duty with blaed bosch , nut & bolt with double washer 1/8x1(1 sut) , nut & bolt with double washer 1/8x2(1 sut) , nut & bolt with double washer 1/12x1(1.5 sut) , nut & bolt with double washer 1/12x1-1/2(1.5 sut) , h.duty batterycharger with incloser , musroom push bottan red , h.duty fut switch teknic/jigo , fut switch element l&t/switch , water resistance box for 300 hp , oneway switchhavells/anchor , electronic regulater dinospeed ed currenthavells/anchor , digital magger meco make modle-dit 99 c , clamp meter modle-3690 rishi/mecho , fibre glass tape1” , empire tape 3/4 , c.r.c.2.26 spray bottle, 400 gram ml , fibreglass tape 3/4 , ferrule 25mm2,0-9/0-mm2 , copper strip 2” widthx1/4 , cable gland 3x240mm , g.i. wire 4 swg , cable gland 3x195 mm/185 , bus bar insulator size ½”x8” suman/lby/wingwan , allu bus bor strip 10x5mm2 , hrc fuse n.s. type 16 amp. , glass sleeve size 1mm , glass sleeve but size 2mm , glass sleeve butsize 3mm2 , glass sleeve butsize 4mm2 , glass sleeve butsize 5mm2 , glass sleeve butsize 6mm2 , glass sleeve butsize 7mm2 , glass sleeve butsize 8mm2 , glass sleeve butsize 9mm2 , glass sleeve butsize 10mm2 , h.t.tape size ¾” , h.t.tape but size 1 , battery terminal 12 vote , phase testertaparia make , wooden board 8”x10” , porceline pipe ¾ “x12” , angle holder anchor makehavells , ceiling rose anchor make havells , saddle size ¾ “ , wooden board with sunmica top 9”x12” , power condenser 2.5mfd havells/gc , do but 4 mfd , -----d0------but 4mfd , -----d0------- but 6 mfd , ----- d0------ but 8 mfd , ----- d0------ but 33 mfd , -----d0------- but 100 mfd , c.t.c. , pendent holder k-555 , tube holder bajaj/anchor/havells , condenser 15 mfd,440v/anchor/havells , cotton tape 1” , araldite 180 grms tube , porcelisne s.t. holder 250 , ----- do------ prut 70 watt. , hand lamp complete with lamp , heater &element 150 watt. surya , cotton tape ¾ , s.t. holder 100 watt k-555 , petroleum jolly , exhaust fan,1440 rpm 18 ke / havells , condenser 12 mfd/ lo mfd 250 volt usha make , ----- do--- but 20 mfd , ----- do--- but 30 mfd , soldering wire 18 swg, , white patrol , film paper 10 mile , screw driver set taparia/jhalani , screw driver no.839 taparia/jhalani , screw driver no.832 taparia/jhalani , screw driver no.829 taparia/jhalani , g.i. strip 1/8”x2” ici markedtaparia/jhalani , screw driver no.829 taparia/jhalani make , screw driver no.929 , nose plair size 8” , soldering iron 250 watt. havells/gompton , insulating plair size 8”taparia make , soldering iron 35 watt. wala/mcare , cable 4 loud50 mm2 , ------ d0---- but 120 mm2 , ----- d0------but 185 mm 2 , black tape ¾ , flash type switeh & socket combimed 15 amp.anchor make , s.c.holder 60/100 watt jyoti make , button holder anchor make havells , flash type switch 5 amp anchor mak , flash type switch 5 amp anchor make , metallie carbon bush with tail,grade e-15 size 3/8”x7/8”x1.5” , do but 16x31x40,mm , ----d0—but 12x171x30 mm , ----d0—but 15x20x65 mm , air dry insulatingvarnish dr back make , bactrol gray vanish dr back make , thinner for varnish , tumbler switch porclinebase 15amp.kay make , ---d0----- but 5 amp. , plug top 5 amp. anchor make havells rk , ---d0----- but 15 amp. , metallic carbon bush without tail grade-15 sige ¾”x1”x3” , carbon bus holder brass base for cane unloader dewalt , nicrome wire 20 swg , nicrome wire 23 swg , dioide forward polarity 321,150,ratan shah make jyoti , ---d0---but 321 um100g , flexible pvc capper twin twisted 23/26 2 core vidyut / hemtron national make coil & 91.44 mtr , ---- d0--- but 40/76 , pvccopper wire/lore3/22 nationalmake havells , pvccopper wire/lore3/20 nationalmake havells , pvc copper wire lore3/22 national/vidyut/havells , ---- d0--- but 3/20 , ---- d0--- but 7/20 , ---- d0--- but 7/22 , pvc copper wire,1core7/18 national/vidyut/hemtrox make(coil of 91.44mtrs) , ----do----but 7/20 , workshop flexible wire2 core,40/76,national/vidyut/hemtrox make(coil of 91.44 mtrs) , -----do----but 23/76 , push button switch with element 3-11] 1not 1nc , limit switch type lt/lrgr.no.7-13 ac-11415v 1.5 amp d.c.-11,vaishvion make , multi meter sanwa make small size micho/rishi , limit switch type c.s. 100v, 1nc, 10a,500a ]ac.vaishnomake , proximityswitch as per sample stronger , electronic timer et-100 semens /l&t , ag timer 0-110 sec. terminal l 1+2controlsupply 3+4 instant hours 5+6 delay ete ,double relay , ----- do---- but 0-50 sec. , fuse base & carrir cutout backalite 50a , ----- d0--- but 63 amp , ----- do--- but 15/16 amp , glass fuse 5 amp , indicating lamp pin/serew type 50 voltjigo/ae , holder for indicating lamplamp 3 watt. jigo/ae , mataliecarbon bush with out tail ¾”x1”x3” , ---- d0--- but 8x20x35mm , --- d0—but 16x32x40mm , do---- but.19 x 40 x 50 mm , --- d0--- but 22x32x45mm , pvc flexible copper wire 1-5 mm2yudyt make havells , pvc copper wire 6lare 120/76 double visulated national/anchor , solenoid coil 230 v a/c for s.d. machinerotox/rutork , multi core copper cable 12x115sq mm national/vidyut/hewtron make , power capacitor universal/lot/siemeus make , slipring carbon holder brass frame lcw -250kw-67, rpm-1630, v-rotor v-2287 for spray pond , fixed & moving kit mei make starter type n-2 suitablefor 200 hp motor rating 300/%a 415 v , fix & moving kit for sliring motor startertype osr-10-8 hp-120, v-415] mb1 make , fusebase with cap & gagu ring 63 amp tp. for d.z. type fuse b.l. make , d.z . type fuse 63 amp. , d.ztype ring 63 amp , ------ d0---- but 25 amp , dztype fuse link 63 amp l&t, semens , copper wire swg havells/anchor/polycab , copper wireswg , fuse cop 25/35 amp , fuse cop 63 amp , hrc fuse link d2 type 25amp , -------- d0---but 62 amp , kit kat porciline unit 16 amp , ---- d0---32 amp , d.p. main switch 16 amp 415. standerd makehavells/l&t , ------ d0—but 32 amp , fixed & moving contact rs-15 kilburn make , ----- d0--- but 5d -15 , carbon bush 1.5”1/3/8”) , dztype fuse base tripple pole 415v,63 amp , ------ d0----- 35/25 amp , dz type guagering 35 amp , d2 type fuse 25/35 amp , corbon buse holder for500 hp motor , do for 210hp motor , motor terminal connection plate 40 hp (kec) make , ------- do--- but 60 hp , ---- do---- but 15/25 hp , ---- do---- but 15 hp , moving iron amp meter flash type dia ct operated 600/5 amp aemake , c.t. 600/5 amp af2 make l&t , amp meter pedastal type 0-30 amp to 60 amp , amp meter 300/5 amp size 144x144ae make , volt meter 0-600 amp , amp meter 200/5 amp 96:96 ae make erh/rc , volt meter o-150 size 144x144 ae make , amp meter square mounted 75x75 mm2400 /5 amp ct operated ae make , hylimerod ½ “/ ¾” , mcb 6 amp. mps/ ind.copp 10 amp , k.w. meter range 0-300 ct-400/5 amp 3 pole 415 volt size 144x144 , stay wire , stay insulator ¾”x4” , terminal connector 2-5 mm elemex make , a.c.s.r. conductor , digital multimeter frequency meter make- ae/abb/ l & t. , carbonbushsize100x20x20 mm , ------- d0 ------ but 20x20x20 mm , digital multimeter electronic , model 9a, dmm-18,meea meter pvt ltd. , baokelite fuse (cut-out)63 amp .standard make , ------- do---- but 16 amp , fuse for a.v.r. , slipring 150 kw/100 hpmake ke/l&t , bengin , meggarr 1100 volt motwani i make , hylumsheet ½” , switchgear items itemmake meeho , super enamalled copper wire devidayal/htp/bic , cables lugs dowell’s make , condenser80mfd asian/usha make , fiber glass sheet all size , cotton tape size ½”steel grip , d.c.c. allu wire all size , change over switch 63 amp standard makel & t , -------d0--- but 100 amp , hrc fuse type gsa 50 amp , spare kit sd-15 kilburn make , serew driver 12” taparia male , ------ do---- but 10” , film paper 14 miles lrs/ uokho , soldering iron 65 wattom/rc , soldering wire 21 swg , fixed & moving contract kit r-5,50 hp, 460 v , magnetic coil for spare kit make gikfun / hoby magnet , s.t. holder 300/500 watt jyoti make , pvc copper unarmoured flexible cable 1.5mm*15crore,500v national make 151mark , twin twist copper wire 14/76 2crore 151mark each coil of 91.44mtrs , pvc allu wire 2.5mm 2crore 151mark (coil of 91.44mtrs , lamps &tubescrompton/bajaj make/ ancher , fittings& accessoriies crompton /bajaj make/ ancher , hn type fuse base 630 amp e.e. make om/rc , ------ d0---- but 400 amp , t.p. fuse base d~ type 500 v. 63 amp, bch make , --------- d0------------ but 25 amp , fuse cap for above 63 amp bch. make , ---------- do--- but 25 amp , guage ringfor above 63amp , tpn switch 32 amp havells make/crompton , ------- do------ but 63 amp , power contactor 20 amp 415 v.bch. make , -------- d0------ but 25 amp , --------- d0 ----- but 40amp , no volt coil 20 amp bch. make , ------- d0----- 40 amp , o.l. relay 8 to 13.5 amp bchmake , ------- d0 ---- but 13.5 to 20 amp , slipring assembly asi make for 170 hp motor , heater element 2000 watt best quality , motor cannectionlead , fuse wire 20/25 amp , compensatingcablek type , leatheriesed paper , porcilinkitkat 100 amp , diode w-400,d-170 forwand for weling machine , p.t.bulb 100 watt crompton/ phillips , urica wire 10 sws , amp motor 144x144,0-5 amp dc-75 mv. , amp motor 21/2,0-5 amp dc. , volt meter 21/2x21/2 0-150 vdc , suppressor superstar for 1500 kw alternator , combination plier-8 make taparia , screw driver-8 , crc-226 ml-300/ 400 , multi meter meco , slipring id-73 od-205lenth-142 , proximitly switch 30 vdc , p.t. holderanchor , st holder 100 wattanchor , pvc tape 3/4steelgrip , condensor 2.5 mfd havells , condensor 3.15 mfd havells , condensor 4 mfd havells , condensor 6 mfd havells , proximitly switchdia 18 mm 200 ma/ stronger , smps 240 volt input-24 volt d.c.2.5 amp. omron , push bottan station10 way make ae , condensor 10 mfd havells , glass tape steelgrip , volt meter 4 500 volt , amp meter 4 150/8 amp0 ctr , c.t. 60/5 amp ae/l&t , c.t. 30/5 amp , c.t. 800/5 amp , amp meter 4 60/5 amp ae/rc make , diod 321 farward ruttonsha/ axeit make , diod 321 reverse ruttonsha/ axeit make , clamp meter a/c d/c 1000 amp. , potentio meter 10 k make rc , amp.meter dc-6 0-10 amp. , glass fuse-30 mm 10 mm with fuse , remote push botton set complet. make kamcon , heavy dutty magger 500 watt yokins/ risabh , teflon tape champion , soldring iron 25 watt , amp meter ctr 600/5 amp dia-3.5 ae/rc , carbon brush copper- 21.5 x 32 x 52 , continiuty tester with celltaparia , phase tester taparia , mcb 10 amp. dpanchor/ abb , mcb 10 amp. sp anchor/ abb , mcb 32 amp. tp anchor/ abb , mcb 63 amp. tp anchor/ abb , mcb 6 amp. sp anchor/ abb , mcb 6 amp. dp anchor/ abb , hydaulic thruster for cane unloder , pvc copper sumbersible flate cable-35 mm x 3 core , copper flexible wire-23/76 havells/ rr cable , w/s flexible copper wire-23/76 x 2 core havells/ rr cable , copper wire 2.5 mm x 1 core havells/ rr cable , copper wire 4 mm x 1 core havells/ rr cable , copper lug- 16 mm h.d dowells , copper lug- 25 mm h.d dowells , copper lug- 35 mm h.d dowells , copper lug- 50 mm h.d dowells , alu. lugs- 25 mm h.d dowells , alu. lugs- 35 mm h.d dowells , alu. lugs- 50 mm h.d dowells , alu. lugs- 70 mm h.d dowells , alu. lugs- 95 mm h.d dowells , alu. lugs- 150 mm h.d dowells , alu. lugs- 240 mm h.d dowells , sv choke 250 wattbajaj/ philips , sv choke 400 wattbajaj/ philips , pvc copper wire 1 mm x 2 core rrcable/ havells , led light- 14 watt bajaj/ philips/ cropton , pt. bulb 100 watt bajaj/ philips/ cropton , st bulb-100 wattphilips/ cropton , pvc copper wire 1.5 mm x 2 core havells/ rrcable , pvc copper wire 2.5 mm x 2 core havells/ rrcable , pvc copper wire 4 mm x 3 core havells/ rrcable , pvc copper subnersibile flate cable-35 mm x 3 core , copper flexible wire-23/76 , w/s flexible copper wire-23/76 x 2 core , pvc copper wire 2.5 mm x 2 core , ignitor for s.v. lamp bajaj / surya , s.v. lamp 250 watt bajaj , s.v. lamp 400 watt bajaj

Central Government/Public Sector

TRN :49025658 | 22 May, 2025

Tender Value : 0

Gorakhpur - Uttar Pradesh

Tender for supply of ,disconnecting and earthing device 8-pole two way, no -off on load 63amp, 750vac (1 000v insulation ), four nos. auxiliary contact (2no + 2nc) with heavy handle and pad locking arrang ement in earth position, without sheet steel/ stainless steel enclosure, suitable for ac 23 duty, confirm ing to is:13947/iec 60947, as per bill of material of rcf spec. no. edts-355 (rev.-1). accepted make & model: cat no. 73342sib032logbss of m/s l&t/salzer or m1370827407 of m/s schaltbau, suitable for eog lhb non ac coaches.%u201d l&t-salzer/schaltbau or any other make. the make and model of equipment of any other make and model of equipment /component can only be considered with pri or approval of rdso/rcf. [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

TRN :49025789 | 03 Jun, 2025

Tender Value : 0

Ajmer - Rajasthan

Tender for supply of disconnecting and earthing devicedisconnecting and earthing device,disconnecting and earthing device, 8-pole, 2-way, no-off on load, 63a, 750v ac (1000v insulation), 2no + 2nc with heavy handle & pad locking arrangement in earth positi on, mounted in a stainless steel enclosure suitable for ac-23 duty, confirming to is: 13947/ iec -60947, as per sr. no. 15 item no. 12 a1, of bill of material of rcf specification no. edts-3 55(rev.1) & confirming to rcf specification no. edts-355(rev.1) suitable for use in set of pan el of non-ac lhb type eog coaches. [ warranty period: 30 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ] carriage stores depot ajmer, rajasthan 57.00 numbers

Central Government/Public Sector

TRN :49026223 | 14 Jul, 2025

Tender Value : 0

Gorakhpur - Uttar Pradesh

Tender for supply of disconnecting and earthing device 8-pole two way, no -off on load 63amp, 750vac (1000v insulation ), four nos. auxiliary contact (2no + 2nc) with heavy handle and pad locking etc.disconnecting and earthing device 8-pole two way, no -off on load 63amp, 750vac (1000v insulation ), four nos. auxiliary contact (2no + 2nc) with heavy handle and pad locking etc.,disconnecting and earthing device 8-pole two way, no -off on load 63amp, 750vac (1 000v insulation ), four nos. auxiliary contact (2no + 2nc) with heavy handle and pad locking arrang ement in earth position, without sheet steel/ stainless steel enclosure, suitable for ac 23 duty, confirm ing to is:13947/iec 60947, as per bill of material of rcf spec. no. edts-355 (rev.-1). accepted make & model: cat no. 73342sib032logbss of m/s l&t/salzer or m1370827407 of m/s schaltbau or any other make, suitable for eog lhb non ac coaches. note :- any other make and model of equipment/ component can only be considered with prior approval of rdso/ rcf. [ warranty period: 30 months after the date of delivery ] ]

corporations/Associations/Others

TRN :49026548 | 27 May, 2025

Tender Value : 15.15 Lacs

Baghpat - Uttar Pradesh

Tender for tender for providing led street light network in dark zone at iidc baghpat. - supply & fixing 90 w led street light having die cast aluminium body and diffuser with driver set suitable for 90 watt confirming to ip 66 protection complete in all respect with surge protection device. minimum cat aa (crompton/philips with 5 year warrenty against defects,damaged & missing)make: cormpton/philips/bajaj/wipro. 2 supply & fixing steel tubular pole 9.50 metre long designated 410 sp-39 in 1:3:6 cement concrete foundation including excavation back filling etc. complete in all respect. 3 s/f of street light junction box made of smc material complete with 4 way terminal block, cable gland etc. 4 s/f of 6 amp to 32 amp sp mcb (10ka) b curve 5 supply & fixing 32mm dia,1.20m long gi bend pipe with 02 nos. clamp of 50x6mm ms flat suitable for fixing street light on st pole including cost of men and t&p. 6 supply & fixing upsida logo plate(retro-reflective) on st pole including cost of clamp and nut & bolt as per design of e/i. 7 supply & fixing pole earthling of pole by inserting ms rod 20x2500mm in vertically ground level and connecting the pole with the help of 6 swg gi wire including cost of all material, men and t&p. in industrial area as per upsida/uppcl technical specification. 8 s/e of d clamps of 38mm x 6mm flat iron for wall/ roof type service bracket with bolts, nuts etc, complete in all respects including painting with aluminium paint 9 supply & fixing of 100 x 110 mm shackle insulator /100 x 80 mm pin insulator including g.i. bolts/ spindle nuts etc.complete in all respect.as pre uppwd sch. no. 621 10 supply, sagging & tensioning of 6 swg gi earth wire including cost of material, men and t&p 11 suppy,laying & drawing of3x1.5 sq mm pvc insulated copper cable for street/flood lights connection in existing pipe/surface/air as required including cost of material, men and t&p. (havells/polycab/grandlay) 12 supplying and laying of 25 sq.mm 3.5 core aluminium conductor pvc insulated, armoured, served, sheathed cable 1100 v grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand alround and protected with burnt bricks on sides and on top complete in all respects. uppwd sch 510(j)-507 13 supply and laying of 16 sq mm 2 core aluminium conductor pvc insulated , armoured , served ,sheathed cable 1100 v grade in existing pipe/surface/pole etc.( havells/polycab/grandley) schedule 501©-507 14 supply & fixing of 25 sq. mm 3.5 core cable socket/lug with insulated tape in cable termination complete in all respect. 15 supply & fixing of 16 sq. mm 2 core cable socket/lug with insulated tape in cable termination complete in all respect. 16 supply & fixing of 25 sq. mm 3.5 core brass nickle plated compression gland for pvc insulated cable complete in all respect. 17 supply & fixing of 16 sq. mm 2 core brass nickle plated compression gland for pvc insulated cable complete in all respect. 18 providing & fixing 35mm x6mm g.i. earth strip on surface or in recess including cost of gi saddle/al. alloy/cadmium/pvc fastener etc.plated iron screw etc. as required for connections. 19 supply and fixing of ms/gi clamp as per design suitable for fixing shackle insulator, made out for 50x6mm m.s. flat including nut, bolt & washer.(for tun and t-points ) 20 supply , sagging & tensoning of overhead line with insulated acsr weasel conductor including binding etc complete in all respects. 21 supply,sagging,tensioning,jointing and binding of acsr weasel conductor including cost of aluminium tape binding wire and jointing sleeves complete in all respects including materiai,men an t&p for proper completion of work . 22 cleaning & spray painting of st bend pole and power st pole ( upto 7 mtr height in case of shut down) with one coat of red oxide primerand two coat of aliminium paint/pu paint as per direction of engineer incharge including cost of all material, men and hydraulic cran,other t&p ( burger/nerolac/asian mark) 23 painting letter ( pole no. ) 2.5 cmm up to 8.0 cm size complete on street light pole/panel/other electrical properties under upsida including cost of all material , men and t&p. uppwd civilsor sch item mno.817, ch-26 24 supply & fixing of 16 mtr high mast shaft of approved make with rising system hot dip glavanized inside & out sidedip,heavingpolesheetthickness3mm.topdia minium 150 mm, bottom dia 360 mmbase plate 32 mm thicksuitable forwindvelocity asperis 875part 3& havingnocircumferentialweld,withaccessoriesfor highmastsuchasheadframesuitablefor6to12 luminaries&its controlgearboxes 1.5hppowertool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch,including making suitable foundationaspermanufaturedrawing/sitereuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect. (bajaj/philips/wipro/crompton/bp & approved make in uppwd) all respect (bajaj/philips/wipro/bp & approved make in ppwd) with upsida acrylic glow shine prescribed logo 25 supply & fixing of factory wired integral 200 w led flood light luminaries with die cast aluminium housing built with driver set confirming to ip 66 protection complete in all respect, cat.-aa (bajaj/philips/wipro/crompton/approved make in uppwd) with labour. 26 supply and fixing 25a tpn capacity of automatic street light cubicle control panel painted with anticorrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering insteument & instrument box with cts etc. complete in all respect. (with labour) 27 supply and wiring of submain with 2 number 2.5 sqmm frlsh pvc insulated single core multistranded copper conductor cable in existing conduit complete in all respects complete. 28 supplying and laying of 16 sq.mm 4 core aluminium conductor pvc insulated, armoured, served, sheathed cable 1100 v on serface the cable run shall be fixed on ms clamps etc of suitable size or as directed by the e.i. grade at a complete in all respects cable laying in existing pipe. (havells/polycab/grandley) 29 supply & laying of 63 mm hdpe pipe isi marked along with all accessories like socket, bend, couple etc. confirming to is 14930 part il complete with fitting and cutting jointing etc direct in grownd 75 cm below ground level including excavition and refilling the trench but excluding sand cushining and protective covering etc. 30 supply & fixing of 16 sq. mm 4 core brass nickle plated compression gland for pvc insulated cable complete in all respect. 31 supply & fixing of 16 sq. mm size pin or plan type copper tin plated socket/lug to cable leads with insulated tape and making connection to point complete in all respect. 32 supply & fixing of 50 mm dia gi pipe b class for climbing up the cable from ground to over head line lt pole complete with gl fitting including material, labour and t&p as per upsidc sch item no. 25a. 1(ls 6.0 mtr for each hm) 33 supply and laying of 32mm x6mm g.i. earth strip from earth electroded directly in the ground level as required on surface or in recess including cost of gl saddle/al. alloy/cadmium/pvc fastener etc.plated iron screw etc. as required for connections. (5m for each) 34 s/b of 40 mm dia x 4.5 mtr. long g.i. pipe vertically for earthing having 12 mm dia. holes spaced 75 mm apart drilled upto 2 mtr, from the bottom complete with earthing lead of no.6 to 8 swg gi wire in g.i.pipe upto appron upto switch board 30 cm square box with hinged cover masonary enclosure. funnel of top, alternate layers of charcoal and salt at least 150 mm thick alround etc. as per direction e/i complete in all respect as per drawing uppwd sch. no. 701 35 supply & erection of stay set at 3.5 metres away from the pole complete with galvanised 19 mm dia x1.80 metre long stay rod, 30 cm x 30 x 6.3 mm anchor plate, thimble stay clamps, stay insulator, 19 mm 600 mm double screw tightener, 7/3.5 mm g.i. stay wire etc. in 1:3:6 cement concrete complete in all respect. 36 supply & fixing of led light strip with driver on street light pole at central verge road no. 1 &2 including cost work t&p men and material complete in all respect. the led strip should be in tri colour as red, white and green (each colour 6 mtr.respectively.) with 01 year warranty against defects/damage/missing. 37 supply and wiring of sub main with 02 nos.of 2.5 sq.mm frlsh pvc insulated 1100 v grade single core multistrand copper conductor cable in existing conduit complete with supply of all material labour and t&p required for proper completion of work as directed e/i 38 fabrication, supply and fixing of work information board in m.s. frame made by 50mm dia square pipe of stainless steel grade ss-304 & 16 mm thick base plate with back supporting of bracing by ms flat of 25x6mm and 2.85 mtr long supporting leg made from 65mm pipe ss-304 grade with proper grouting arrangement. the board should be retro reflective type in green color with white letters as required and shall be fixed at a height of 1.2 meter from ground by providing 0.45x0.45x0.60 mtr cement concrete stone pad as per drawing enclosed.the borad should be installed within 07 day of signing of contract boand.)

Local Bodies

TRN :49010361 | 19 May, 2025

Tender Value : 0

Gorakhpur - Uttar Pradesh

Tender for the municipal corporation has a tender information to determine the rate for all the festivals like moharram dussehra deepavali chhath puja christmas kartik purnima and makar sankranti etc _ item 02- temporary supply & fixing erection & removal of steel tubular pole sp 27.temporary supply & fixing erection & removal of d. clamp.temporary supply & fixing erection & removal of 75mm shackle insulator.temporary supply / sagging over hand line acsr vessel conductor wire erection & removal.temporary supply & fixing erection & removal of stay set complete

Boards / Undertakings / PSU

TRN :48996540 | 13 May, 2025

Tender Value : 1.47 Crore

Matunga - Maharashtra

Tender for repair, renovation, and reconfiguration of lab 1 at the computer engineering and it engineering department, first floor, vjti, matunga, mumbai.= 1 dismantling of existing partitions, wall paneling, etc., all complete as per site requirements, and stacking the usable materials within building premises as directed by the architect/consultant/ engineer-in- charge, etc. complete. (lead upto 100 meters) 2 removal of cement tiles, existing flooring, wall tiles,marble, polished shahabad flooring, dado with or without bed concrete, including stacking the materials as directed, with all leads, lifts, etc., complete. (lead upto 100 meters) 3 dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc. complete. ( lead upto 100 meters) 4 scraping the old paint from the plastered internal surface using a dust-free vacuum paint scraper, followed by coating the entire surface with a mixture of whiting or glue and linseed oil, including the provision of scaffolding, as directed. (the scraping of old paint should be done until the neeru finish of the plaster is achieved.) lead and lift upto 100 meters etc. complete. 5 removing old paint from steel and other metal surfaces and making the surfaces even with hand scrapping, scaffolding etc. complete. 6 removing the existing cement plaster of any thickness without causing dust nuisance, stacking the debris up to a distance of 100 meters, cleaning the site, etc. complete. 7 providing and applying an anti-corrosive chemical to exposed reinforcement of r.c.c. members such as beams, columns, and slabs. this includes one coat of alkaline rust converter (feovert, rusticide, or equivalent) after cleaning the surface with a wire brush, followed by two coats of anti-corrosive, epoxy-based, two-component, zinc-rich primer (materemaco p 130 of basf, phenolic ipnet rb, polyalk flxoprime, or equivalent) for rebar protection on exposed reinforcement. additionally, apply a concrete-penetrating corrosive inhibitor (epco kp-100, polalk ep 113, masterseal 1414 of basf, fosroc, or equivalent) over the adjoining concrete surface. etc. complete. 8 providing and applying a bond coat of approved epoxy resin (masterbrace 1414 of basf, epi bond of krishna conchem, or equivalent) before polymer plaster or concrete to ensure a perfect bond between old concrete and new concrete/polymer plaster surfaces. the bond coat should be applied within half an hour after preparation, conforming to astm c881 type 2. this process includes the use of nylon brushes, scaffolding, labor, etc. complete. 9 providing and applying ready-mix polymer-modified cement mortar with an average thickness of 15mm, using polymer in one or more layers, in a proportion of 1:5:15 (polymer, cement, and quartz sand) as per the manufacturers specifications. the surface should be cured after 72 hours of application using wet gunny bags, etc. complete. 10 providing and applying ready-mix polymer-modified cement mortar with an average thickness of 30mm-50mm, using polymer in one or more layers, in a proportion of 1:5:15 (polymer, cement, and quartz sand) as per the manufacturers specifications. the surface should be cured after 72 hours of application using wet gunny bags, etc. complete. 11 providing and applying a 30mm thick self-curing ceramic polymer microconcrete of an approved make, having a compressive strength above m30, non-shrink, and impermeable, as a filling mortar for load-carrying r.c.c. members in two layers on cleaned concrete surfaces, including honeycomb areas (using manual or mechanical means). the mortar shall be prepared by mixing nicosil c80 and fresh 53-grade cement with the required water-cement ratio to achieve the desired consistency. the application and finishing shall be done by manual trowelling. curing shall be carried out after the initial setting time, in accordance with the manufacturers specifications. the work shall be executed in line with the specifications and as directed by the engineer-in-charge. the work must be carried out by a certified applicator, and the work shall be guaranteed for 5 years. the guarantee shall be provided on a rs. 500/- stamp paper. (the bond coat, as per item no. 08 in the boq, is to be applied before the coating.) 12 providing and applying 12mm thick internal/external ready-mix plaster conforming to is: 4031 (part-4) 1988 and is: 383-1970, in a single coat using cement mortar in a proportion of 1:4, with a special type of polymer additive (approximately 0.4%), on all types of surfaces in all positions, including scaffolding and curing. the plaster shall be followed by a smooth finishing coat of gypsum plaster of 6mm thickness, ensuring an even, smooth surface suitable for painting. complete with necessary curing, scaffolding, and all other related works. 13 providing and applying a priming coat over new/old steel and other metal surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt, and other foreign matter. the surface shall be scoured with wire brushes, fine steel wool, scrapers, and sandpaper, with scaffolding as required, etc. complete. 14 providing and applying priming coat over new wood and wood-based surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt, and other foreign matter, sanding, knotting, scaffolding, etc., complete. (brands such as asian paints, dulux paints, nerolac, berger, royal, or equivalent make.) 15 providing and applying two coats of synthetic enamel paint of approved color to new/old structural steel work and woodwork in buildings, including scaffolding if necessary, cleaning, and preparing the surface (excluding primer coat). etc. complete.(brands such as asian paints, dulux paints, nerolac, berger, royal, or equivalent make.) 16 removing and refixingof doors and windows with frames and stacking the materials as directed, including all leads, lifts, labour, fitting etc., complete. (lead up to 100 meters) 17 providing and laying in pattern 600 mm x 600 mm vitrified tile flooring of 8 to 10 mm thickness and confirming to is 15622-2006 ( group bla) of approved make,quality, shade and pattern for flooring . the tile flooring shall be laid in pattern with 2 mm spacers & tiles fixed in cement mortar of 1:4. the rate shall be including floor chipping to attaining required levels, epoxy grouting of joints using approved matching colour tile grout of epoxy grout, necessary protection of the laid floor, acid wash cleaning for any stains before handover. etc. complete as per the drawing, specification and to complete satisfaction of the engineer. rate to include the wastages as per the pattern indicated in the layouts. brands like kajaria, johnson or similar etc. groove shall be filled with grout of approved shade ( brands like laticrete etc.) as dicectedby the engineer-in-charge. etc. complete. basic rate for tile material- rs. 1440/- per sq.m. 18 providing and fixing skirting, including labor, materials, and all related work, etc., complete. rate for skirting of height up to 150 mm. 19 vinyl flooring for hod cabin:providing and fixing approved color homogeneous flooring, 4mm thick with interlocking system, single-layered flexible spc vinyl flooring (spica by tusker vinyl floorings) in roll form, over the provided i.p.s. or kota stone flooring. the flooring will be fixed using approved adhesive, and all joints will be soldered with pvc rods as per the manufacturer’s specifications. the work will be completed as directed, ensuring proper leveling and cleaning. the roll width will be a minimum of 2.0 meters, and the weight of the pvc flooring will be 90 kg per 30 sqm. as directed and approved by engineer in charge. etc complete. basic rate for vinayl flooring material- rs. 900/- per sq.m. 20 providing and laying vitrified mirror/glossy/matte finish tiles of size 590 mm to 605 mm x 590 mm to 605 mm with a thickness of 8 to 10 mm, conforming to is 15622:2006 (group b1a) from an approved make, shade, and pattern, for dado and skirting in the required positions. the tiles shall be fixed in 1:4 cement mortar, including neat cement float, filling of joints, curing, cleaning, and all related work, etc., complete. basic rate for tile material- rs. 790/- per sq.m. 21 providing second-class burnt brick masonry with conventional/i.s. type bricks in cement mortar 1:6 in the superstructure, including striking joints, raking out joints, watering, scaffolding, and all related work, etc., complete. 22 lowering the debris obtained from breaking and removing cement plaster/burnt brick masonry from the first floor by any means, without causing dust nuisance or damage to the structure. the debris shall be stacked as directed by the engineer-in-charge, including cleaning the site, etc., complete. (lead up to 100 meters.) 23 removing and disposing of debris from the site to a dumping ground outside the vjti premises (in accordance with municipal rules), etc. complete. as directed by the engineer-in-charge. (minimum 6 cu.m debris per trip) 24 providing anti-termite treatment to the wooden frames of doors and windows of the existing building as per i.s. 6313 (part-iii), by drilling 6 mm dia. holes at the four corners on one side and the four corners on the other side, at a downward angle of approximately 45 degrees at the junction of the woodwork and masonry. injecting 150 ml of chlorodane 5% w.c. into each hole and sealing with putty, etc., complete, with a 2-year guarantee on bond paper. 25 providing and applying waterproof melamine polish of the required finish to the woodwork by spray machine, including knotting and preparing an even surface by scraping, applying french polish, scaffolding if required, etc., complete.note: the work is to be executed only with prior approval from the superintending engineer. (brands such as asian paints, mrf melamine or equivalent.) etc. complete. 26 providing and fixing ss t/u/l strip profiles for walls, ceilings, tiles, flooring, main doors, interior decoration, bathrooms, and living rooms, including transportation, wastage, labor, etc., complete.shape: t/u/l profilematerial: ss 304 grade stainless steeldimensions: 8 mm to 12 mmlength: 2440 mm (8 feet), 3048 mm (10 feet)type: t-sectionfinish: polishedposition: interiorcolor options: gold, rose gold, black, silver, champagne, antique hairline, antique copperthickness: 2 mm to 8 mmnote: the shape, pattern, color, and design will be directed by the architect/consultant/or engineer in charge. basic rate for material- rs. 850/- per number. 27 providing and fixing ss t/u/l strip profiles for walls, ceilings, tiles, flooring, main doors, interior decoration, bathrooms, and living rooms, including transportation, wastage, labor, etc., complete.shape: t/u/l profilematerial: ss 304 grade stainless steeldimensions: 16 mm to 32 mmlength: 2440 mm (8 feet), 3048 mm (10 feet)type: t-sectionfinish: polishedposition: interiorcolor options: gold, rose gold, black, silver, champagne, antique hairline, antique copperthickness: 2 mm to 8 mmnote: the shape, pattern, color, and design will be directed by the architect/consultant/or engineer in charge. basic rate for material- rs. 850/- per number. 28 providing and fixing sign boards foor doors:specification for waterproof signage boards (12 x 4 inch)size: 12 inches (l) x 4 inches (h) (with size tolerance is plus or minus 1%)material: high-quality, durable acrylic or pvc boardfinish: glossy or matte finish for clear readabilitywaterproof: weather-resistant, suitable for both indoor and outdoor usedesign: custom text, graphics, or logo engraving/printingmounting: wall-mountable with adhesive backing or screw mountscolors: available in multiple colors with contrast for visibility (e.g., white, black, silver)application: ideal for office cabins, rooms, labs, and other signage needsthis durable, waterproof signboard ensures clear and professional signage in various environments. including wastage, etc. complete. basic rate for material- rs. 460/- per number. 29 providing and fixing of 3d wall panels that can be painted as well.size of each panel: 2 x 2 feet.colour: any color, design, or pattern.features: lightweight, fire-resistant, easily diy, 100% recycled.made from natural bamboo plant fiber, etc., complete. basic rate for material- rs. 450/- per number. 30 providing and fixing wooden decorative fluted wall panels/louvered wall panels:material: high-quality wood (mdf, plywood, or hardwood) with a decorative veneer finish.dimensions: 8 feet x 4-5 inchesthickness: 8 mm - 12 mmdesign: fluted design with vertical or horizontal grooves for a decorative effect.color: multicolor/any colour. (customizable to match interior themes).shape: rectangular panels for seamless installation, etc., complete. basic rate for material- rs. 850/- per number. 31 providing and fixing machine cut mirror polished 16 mm to 20 mm thick telephone black / amba white / cat bary brown / rbi red / ocean brown granite stone partition with rounding the edges etc. complete. one side polishbasic rate for granite material- rs. 2530/- per sq.m. 32 providing and fixing oval-type under-counter wash hand basin of 16-inch x 22-inch size and of special color shade, having telephonic black/colored granite of 180mm thick stone black kadappa framework, including chromium-plated coupling bottle trap. the wash basin should be of cera company or equivalent, model no. 3448, as per the detailed drawing or as directed by the engineer-in-charge, etc., complete. (counter size 1.20m x 0.60m). (brands such as jaquar,kohler or equivalent make.) basic rate for wash basin - rs. 6000/- per number. 33 providing and constructing a granite kitchen platform with the installation of a stainless steel sink (600mm x 450mm) as per the detailed drawing, including vertical polished kadappa stone supports (25 to 30mm thick) on both sides, with a kadappa top (35 to 40mm thick) and a polished granite top (16 to 20mm thick). the platform will feature granite strips at the front and both sides, with two vertical granite supports (15 cm height). the top granite will be 75 cm x 40 cm, including cutting and opening for the sink of the required size in both kadappa and granite. the platform size is 5.00 m x 0.60 m, with a height of 0.75 m, etc. complete with all required finishing. basic rate for ss sink- rs. 6000/- per number. 34 supply and installation of 600x600mm modular metal perforated grid ceiling system (cg-01)the ceiling system shall be supplied and installed as per the specifications provided in the tender document, and in accordance with the directions and approval of the engineer-in-charge. the scope includes complete installation with all necessary materials, components, and finishing to ensure proper execution etc. complete. 35 providing and installation of aluminum frame works for partition with ply on both sides and laminate finish: providing and fixing partition aluminum frame work consist of 25mm x 50mm x 1.2mm thick extruded aluminium box section framework at spacing not exceeding 600mm centre to centre both ways (horizontal and vertical). the framework shall be secured at floor structural ceiling and sill/ lintel level with 25 x 50mm x 1.2mm thick horizontal aluminium section. framework to be secured to floor / walls / columns / ceiling / beams using 75mm metal screws and dowels.acoustic infill: providing & fixing acoustic insulation of approved make to g.i./ aluminum/ ms/ wooden frame partition of 50mm thick rockwool of density 48 kg/m with blanket wrapped in rp tissue suitably affixed to partition framework using where necessary gi binding wire duct tape as indicated in the drawing.outer skin:- providing and fixing 18mm plywood of brands like greenply, century or equivalent. finished with 1 mm thick laminate of approved shade applied on plywood of brands like formice, royal touche or equivalent brand.note: rate is as per aluminum framework with both side ply and laminate. etc. complete. 36 providing and fixing of laminate cladding with ply backing:providing and fixing 12mm bwr plywood (brand: greenply, century, or equivalent), directly fixed to the column. a 1mm thickness laminate of an approved shade, applied on the plywood surface. laminate brands: formica, royal touche, or equivalent. etc complete. 37 providing and installation of glass partition (toughened glass): providing 12mm toughened fixed glass partition including all patch fittings, ensuring smooth and even flush joints between glasses, fixing the same in positions to true line and level, finishing the wall joints with clear silicon sealants, cleaning the surface and ensuring that there are no scratch marks on the glass etc. complete as per drawing and specifications, glass brands should be dorma, ozone or equivalent. 38 providing and installation of glass partition (dgu glass): double-glazed unit glass with air spacer of 6 to 16mm, 95% transparency, etc. complete as per drawing and specifications, dorma or ozone or equivalent. 39 providing and installation of 12mm thick clear toughened glass door with film as required. (d2 - 0.91 x 2.10 m) specification:hardware: door to be complete with hardware to each leaf as follows: hinges: 8 nos. ss ball bearing butt hinges. door closer: concealed door closer with hold open. lock set: dead lock as approved.door handles:900mm ht. 36mm dia d type offset handle on both sides in approved powder coating. door stop: floor mounted door stopper as approved seals: drop down floor seal as approved. security system: na note: all the metal profile sections and hardware finish should match the frame. brands like dorma or ozone or equivalent. etc. complete as per drawing and specifications. 40 providing and installation of d1 - double door two-way sliding motorized door, suitable for door openings up to 1.20 meters with a maximum door weight of 100kg (both leaves). the door offers environmental protection with a working temperature range of -20°c to +50°c and is rainproof. it has a standard opening time of 3-8 seconds, with a remote control operating distance of 100 to 200 feet (depending on line of sight). the opening size is 2.4m x 2.10m, and the glass door size is 1.2m x 2.10m. brands like dorma, ozone, or equivalent, to be installed as per drawing and specifications. etc. complete. 41 providing and installation of d3 - 1.09m x 2.10m (single shutter) 12mm toughened glass door with fixed side panels, including all patch fittings, locking mechanisms, and ensuring smooth, even flush joints between the glass panels. the door is to be fixed in position to true line and level, with wall joints finished using clear silicone sealant. the surface should be cleaned and inspected to ensure there are no scratch marks on the glass. installation to be completed as per drawing and specifications, with brands like dorma, ozone, or equivalent. etc. complete. 42 pop punning: providing and applying of plaster of paris punning(1st quality isi approved pop) over plastered with minimum thickness of 8mm-12mm to existingwall surfaces, ceilings & concrete members etc., to be finished in line and plumb with smooth surface ready to receive paint base. rate to be inclusive of edge protection (gi), fibre mesh for service conduits,hacking wall surfaces for better bonding, cleaning, scrubbing the surface, providing grooves if necessary etc., complete as per architects/consultant/engineer-in-charges approval. brands like gyproc, armstrong, shera or equivalent etc. complete. 43 plastic emulsion paint (leed compliant, low voc): providing and applying plastic emulsion paint finish to walls, partitions, and ceiling surfaces of approved make, color, texture, and shade in two coats, with surface and finish acceptable to the engineer in charge to be achieved within these two coats. any additional coats, if required, shall be at the contractors cost. the work includes preparing existing surfaces by scraping away loose particles, dust, etc., washing and scrubbing, filling cracks with crack filler and binder, cleaning and making the surface dust-free, applying water-based rj london putty as directed, rubbing with sandpaper to smooth the surface, and applying one coat of primer as recommended by the approved paint manufacturer. the work also includes providing necessary scaffolding, cleaning, and protecting the site until handover, as well as masking and protecting all service devices such as switchboards, detectors, etc. the work is to be completed at all heights and leads, as per specifications or as directed by the architect/engineer in charge/consultant. brands like asian paints, berger, or equivalent are acceptable. etc. complete. 44 providing and applying premium decorative wallpaper high-end or custom designs (special finishes, custom patterns)specifications: material: non-woven fabric or vinylroll size: 21 inches wide x 33 feet long (covers 55 sq ft)pattern: various styles (floral, geometric, etc.)finish: matte, gloss, or texturedinstallation: peel & stick or pastefeatures:scratch & water-resistanteasy to clean (wipeable)fade-resistanteco-friendly, voc-freeideal for: living rooms, offices, and accent wallsmaintenance: clean with a damp cloth, no harsh chemicalscustom options: available in various colors and patterns, custom designs upon request. basic rate for wallpaper rs. 600/- per sqm. 45 standing platform (300-450 mm from ffl):construction of a standing platform at a height of 300 mm to 450 mm from the finished floor level (ffl), as per approved dimensions. the platform will be made of 18 mm thick wood (century, greenlam, or equivalent) and finished with wood polish (asian paint wood tec, mrf, or equivalent).materials:frame: mild steel or aluminum, powder-coated for corrosion resistance.surface: high-quality plywood, mdf, or approved materials with a non-slip finish.support: sturdy metal beams or supports for stability.features:height: 300 mm to 450 mm from ffl, as per design.finish: non-slip surface with smooth edges and protective coating.safety: non-slip tread and optional guardrails. etc. complete. 46 stage flooring: supply and installation of interlocking rubber tile flooring at the stage area as per the specifications and drawings provided. the flooring will consist of a 6.0 mm synthetic sport surface, including a =1.50 mm pur protect® treated vinyl surface layer, calendared and grained, supported by a pvc density single closed-cell foam, and reinforced with a fiberglass grid structure. it will feature sanosol treatment for fungistatic and bacteriostatic properties. the flooring will meet the following standards: weight: 3.7 kg/m², impact resistance (en 1517) =8 n/m, abrasion resistance (en iso 5470-1) =350 mg, shock absorption (en14808) =25% (labosport result = 28%), indentation resistance (en 1516) =0.5 mm, ball bounce (en 12235) =90%, vertical deformation (en 14809) =3.5 mm, sliding coefficient (en 13036-4) 80–110, fire (en 13501-1) cfl-s1, anti-viral activity (human coronavirus 229e) – iso 21702 (99.37% after 2 hours), energy return (nf p 90 203) =0.31 m/s, tvoc after 28 days <100 micrograms/m³ (iso 16000-6), floor score®, ce marking, en14904 compliant for multi-sports use, reach compliant, and singapore green label certified. the supply and installation will include making good any damaged surfaces using standard fillers such as birla white cement, cement-based grout, epoxy grout, or mortar, and repainting to match the color.all work will be completed in accordance with the specifications, design, drawings, and the direction of the engineer-in-charge. 47 providing and fixing of overhead storage as per the specifications and drawings provided in the tender document. etc. complete. 48 providing and fixing of surface storageas per the specifications and drawings provided in the tender document. etc. complete. 49 providing and fixing on-site a lab table as per the specifications and drawings provided in the tender document. etc. complete. 50 providing and fixing of office desk/table in faculty lounge as per the specifications and drawings provided in the tender document. etc. complete. 51 providing and fixing of office desk/table in office for hod as per the specifications and drawings provided in the tender document. etc. complete. 52 supply and installation ofhod cabin chair as per the specifications and drawings provided in the tender document. etc. complete. 53 supply and installation of faculty lounge chairs as per the specifications and drawings provided in the tender document. etc. complete. 54 supply and installation of study chairs for labs as per the specifications and drawings provided in the tender document. etc. complete. 55 supply and installation of foldable desklet tables for the seminar hall as per the specifications and drawings provided in the tender document. etc. complete. 56 removingthe exisitng light fixures, fans, wires, cables, swith boards and distribution boards etc. complete. 57 point wiring for independent plug, concealed type in min 20 mm isi marked hms pvc conduit with 1.5 sq.mm (2+1e) fr grade copper wires, modular type switch and socket, earthing and required accessories as per specification no wg-pw/sw. (brands for conduits precision/finolex/pressfit. and for cable barnds should be polycab/finolex/havells. etc. complete 58 point wiring for independent plug, concealed type in min 20 mm isi marked hms pvc conduit with 2.5 sq.mm (2+1e) fr grade copper wires, modular type switch and socket, earthing and required accessories as per specification no wg-pw/sw. (brands for conduits precision/finolex/pressfit. and for cable barnds should be polycab/finolex/havells. etc. complete 59 supplying and erecting flush type shockproof plug socket 6a & 16a (6 pin) with 16a / 25a switch combined with indicator lamp and fuse with gang box on wooden board.make /brand (roma/ legrand,/ greatwhite) etc. complete 60 supplying and erecting isi mark modular type 3 pin 6a / 16a multi socket with safety shutter, duly erected on providedplate and box with wiring connectionsetc.complete. brand : roma/gretwhite/legrand) etc. complete 61 supplying and erecting pvc surface modular double mounting plate 3 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) 62 supplying and erecting pvc surface modular double mounting plate 4 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 63 supplying and erecting pvc surface modular double mounting plate 6 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 64 supplying and erecting pvc surface modular double mounting plate 8 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 65 supplying and erecting pvc surface modular double mounting plate 12 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 66 supplying and erecting regular/ standard model ceiling fan of 1400mm with sweep complete erected in position as per specification no. fg-fn/cf brand /orient/polycab/crompton etc. complete 67 supplying and erecting flush-type ceiling fan regulators and electronic step regulators for ceiling fans (600mm, 900mm, 1200mm, and 1400mm sweep), complete with installation on the provided switchboard. make/brand: roma, legrand, or greatwhite. 68 providing and fixing 36 watt 2x2 light fitingsupplying and erecting square shaped crca /die-cast aluminium powder coated housing led panel light (slim edge-lit) 600x600mm suitable for 36 w-40w includingmotion sensor led light with provision for plane front frame with translucent cover fixed to the housing etc.complete .brand philips/havels/wipro etc. complete 69 supplying and erecting 16 to 32 a dpmcb suitable to fix in 2 module of modular switch in provided box complete & duly concealed with necessary material and connected. (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 70 supplying & erecting triple pole and neutral distribution board (tpndb), 3 pole/4 pole mccb as incomer & outgoing sp mcb (24 poles) or tp mcb of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb1 (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 71 providing & erecting 3 pole mccb, 415 v, 100a, rated short-circuit breaking capacity 25 ka (ics=100% of icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/uv/tripalarm contact. mccb with phase barriers on both sides, insulation withstand capacity 800v, no line-load bias in provided enclosure/panel as per specification no. sw-swr/mccb (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 72 supplying, erecting & commissioning 4 pole rccb 63a, electromagnetic type with 30/100/300 ma sensitivity with earth leakage trip indication complete as per specification no. sw-rccb/rccb. (make/ brand: legrand/ schneider/ l&t/ indo asian) 73 supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, nylon rip cord & grey colour sheathed with fr pvc, conforming to itd specification s/ws 113c laid in provided pvc casing capping/conduit as per specification no. wg-tw etc. complete. cables brands should be polycab/finolex/havells. etc. complete 74 supplying and installing cat-6 cable suitable for networking as per specification no. wg-coc/nc. cables brands should be polycab/finolex/havells. etc. complete. 75 supplying & erecting mains with 2 x 2.5 sq.mm. and earth wire 1.5 sq.mm frlsh pvc copper wire in hms pvc conduit min. 20mm dia. as per specification no: wg-ma/pc.etc complete. brand :polycab/finolex/havels) etc. complete 76 supplying, erecting & terminating xlpe armoured cable 3 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.cb-lt/cu(brand: polycab/ finolex/ havells)note - the quantity of wires for looping the required number of air conditioning units has to be calculated by the contractor with respect to the provided architectural working drawing. etc. complete 77 providing & erecting hot dipped galvanised cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) gi sheet of 150 mm width & 20 mm height complete with necessary hardware. cable tray brands should be profab or equivalent. etc. complete 78 supplying and erecting pvc box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification no: wg-ma/box. etc. complete (make/ brand: legrand/ schneider/ l&t) 79 supply & fixing of aluminum box section to be laid on the floor with all excavation, re-cementing & refinishing civil works to make good in line with the existing floor level respective junctionbox to be fabricated in 16 swg gi sheet with cut out as required for terminating the box sections. shall include pvc conduits from jb to work station powerpoints i)150 x 150x 50 mmgijunction box with cover & cut outs etc. complete. (make/ brand: legrand/ schneider/ l&t) 80 supply of a.c split unit (2 ton) :supply of ac split unit as per the specifications, and drawings provided in tender document. make (carrier/ voltas/ bluestar/ samsung) etc. complete 81 supply of 2 ton casatte ac:2 ton inverter casette ac. cooling capacity 3200-8000 watt. offers uniform 360 degree round airflow, with 4 star energy rating. etc. complete. make (carrier/ voltas/ bluestar/ samsung) etc. complete 82 installation of 2 ton ac split unit etc. complete 83 installation of 2 ton ac cassette unit etc. complete 84 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigerant having 22swg thickness and inner dia/size 22mm complete. etc. complete. material selection should be high quality and from reputed brand as directed by engineer in charge. 85 supply & installation electrical communication cable between indoor to outdoor units.cables brands should be polycab/finolex/havells. etc. complete. 86 providing and fixing in position ms frame stand for a.c. units, floor or wall mounted, with vibration isolation pads and frame to be made out of required ms sections strong enough to hold the weight of the ac unit,and should be lockable, including fixing in position using necessary scaffolding, ladder etc, and painting with two or more coats ofapproved enamel paint on a coat of red oxide etc. complete 87 insulated condensate water drain piping constructed out of pvc / hdpe hard pipeswith 6mm thick nitride insulation, fitting, accessories, bends, elbows, tees, flanges, tapings, wall sleeves, hangers, supports, anchors fasteners and concealed in brickwork or flooring. etc. complete(make: finolex/ astral/ prince) 88 supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided pc / copper pipes having 9 mm thickness and inner diameter / sizes 28 mm for solar water heater/ac system. etc. complete. material selection should be high quality and from reputed brand as directed by engineer in charge. 89 supplying & erecting crca sheet metal enclosures of 1.2mm thickness with 20a, 2 pin plug & earth socket and 20a, 3 pin plug top with 20a/30a single pole mcb having rated short - circuit breaking capacity (icn) 10ka complete erected on angle iron/ gi frame. etc. complete 90 carrying out core cutting of size 3 to 5 dia x 15 length in the c.c./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original. etc. complete 91 supply and installation of roller blindsas per the specifications and drawings provided in the tender document. etc. complete. basic cost for blind cloth fabric material rs.900/- per sq.m. 92 carrying out test for ceramic tiles / vitrified tileswater absorption, modulus of rupture (set of 6 tiles) etc. complete. 93 carrying out test for plywood: determination of resistance to dry heat,determination of moisture content,determination of density,thickness of plywood. etc. complete. 94 carrying out test for test for glue adhesion for plywood etc. complete. 95 carrying out test for hollow / solid /aac blocksdensity test. (set of 3 blocks), compressive strength. (set of 3 blocks), water absorption test (set of 3 blocks) etc. complete. 96 providing and fixing 15 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 97 providing and fixing 20 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 98 providing and fixing 25 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 99 providing and fixing on walls/ceiling/floor 32mm dia cpvc pipe with necessary fittings, remaking good the demolished portion, etc., complete. including removing existing pipeline if necessary and conveying and stacking the same in pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 100 providing and fixing 75 mm dia stabilizer pipe/p.v.c. soil vent/waste pipe with necessary fixtures and fittings, such as bends, tees, single junctions, slotted vent, clamps, etc., complete. 101 providing and fixing 100 mm dia stabilizer pipe/p.v.c. soil vent/waste pipe with necessary fixtures and fittings, such as bends, tees, single junctions, slotted vent, clamps, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 102 providing and fixing 10 cm pvc nahani trap with grating, etc., complete. (brands such as astral, finolex, prince or equivalent make.) basic rate for nahani trap is rs. 380/- 103 providing and fixing c.p. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete. basic rate for pillar cock is rs. 1250/- per number 104 providing and fixing of exhaust fan 150mm crompton/havels/usha or equivalent etc. complete. basic rate for exhasut fan is rs.1000/- per number 105 providing and fixing stainless steel round napkin hanger for bathroom/towel holder for wash basin/napkin holder/bathroom (chrome) b. heavymaterial stainless steel product dimensions 17l x 5w x 19h centimetersfinish type chromeinstallation type wall-mounted shape round including fitting etc. completed.basic rate for material is rs. 320/- 106 providing and fixing premium front glass shelf - bathroom shelf/kitchen shelves wall mounted with frosted and toughen (tradition 6 x 18) chrome including fitting etc. complete. basic rate for material is rs. 650/- 107 providing and installation of 6 mm thick mirror with 6 mm thick ply backing, as per design. the mirror will be supported by stainless steel finished buttons, etc., complete. (the glass brand should be saint-gobain, borosil, or an equivalent make) basic rate for mirror is rs. 1250/- per sq.m. 108 supply and installation of nsd make smoke detectormodel:66a, certification: ce & ertl etc. complete. 109 supply and installation of nsd make heat detectormodel:66h, certification: ce & ertl etc. complete. 110 supply and installation of response indicator make: nsdmodel: p.s (mini) etc. complete. 111 supply and installation of manual call point (m.s) make nsd 112 supply and installation of 08 zone fire alarm panel make nsd(excel) etc. complete. 113 supply and installation of flasher hooter make nsdmodel no: ms17flash etc. complete. 114 supply and installation of supply & laying 1.0 sq. mm x 2 core copper armored isi cable for alarmsystem. with accessories per meter. brand/make :polycab/finolex/havellls) etc. complete. 115 supply and installation of high quality co2 fire extinguisher (6 kg)type:carbon dioxide (co2) fire extinguisher (for electrical fires and flammable liquids)capacity: 6 kgfire rating: class b (flammable liquids) class c (electrical fires)material: cylinder: steel or aluminum alloyfinish: red powder-coated for durabilityoperating pressure: 55 bardischarge time: approx. 8-10 secondsdischarge range: 3-5 feettemperature range:operating: -10°c to +60°c storage: -30°c to +60°cmounting: includes wall bracket certification: is 15683 (india) / ul/ce certified etc. complete.note: the rates for all fire safety alarm items include the complete supply, installation, commissioning, transportation, freight, and all associated costs. 116 providing architectural/ interior design services : scope of work as below:drawings preparation: 3d views, floor plans, furniture layout, electrical layout, ceiling layout, and partition layout.color scheme & material selection: guidance on colors and material choices for finishes, flooring, and furniture.quality control: ensure standards for structural, civil, electrical, fire safety, furniture work and hvac work.interior planning: optimize lab functionality and aesthetics, including furniture, partition design, and system planning (electrical, hvac, fire safety).modifications: suggest changes to designs based on site conditions and client feedback.coordination & monitoring: ensure project progress and timely completion by working closely with contractors. deputation of interior designer degree/diploma/certificate course having knowledge of autocad and 3d home or equivalent for the full period of the work. designes. monitor on-site execution, ensuring design adherence. taking joint measurements.preparing statements for extra items and excess quantities.compliance & safety: ensure adherence to safety codes and regulations. etc. complete.

Related Searched Keywords : steel pole

List of steel-pole Tenders

Get steel pole Tender Alert...

Related Searched Keywords : steel pole

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us