Filters

List of wire-mesh-shutter Tenders

List of latest wire-mesh-shutter Tenders in Indian Tenders. Click on any wire-mesh-shutter Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for wire-mesh-shutter Tenders.

All-Tenders (33)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49021208 | 12 May, 2025

Tender Value : 0

Bhandara - Maharashtra

Tender for material supply for all type construction work and electric water supply material for year 2025-26 (under all fund) , sand , sand local , soft murun , hard murun , metal 100 mm , metal 80 mm , metal 40 mm , metal 20 mm , metal 10 mm , dust , rcc pipe 200 mm with colar , rcc pipe 300 mm with colar , rcc pipe 450 mm with colar , rcc pipe 600 mm with colar , rcc pipe 800 mm with colar , rcc pipe 900 mm with colar , rcc pipe 1000 mm with colar , cement 53 grade isi mark , still 6 mm , still 8 mm , still 10mm , still 12 mm , still 16 mm , centring tar , vibrator needle , water trankar & tractor troali , backhoe loader , vibrator roller , simple steering road roller , mixchar machine , excavator 70 to 120 , excavator 120 to 220 , fiori 1 cubic meter , fiori 2 cubic meter , centring plate , waterproof compound , acrylic polymer modified liquid , acrylic polymer modified waterproofing powder , fibre glass mesh , plastic emulsion paint , water proof cement paint , lead / zink base oil paint , oil bound distemper , primer , washabe oil bound distemper , putty , birla white cement , terpentine , wood primer , information board still with painting , single lef door 16 mm thik , single lef door 32 mm thik , solid panel pvc internal door shutter , door kittas , door fremas , aluminium fixedwindows (two track sliding ) , aluminium fixedwindows (three track sliding ) , aluminium fixedwindows with mosquito net (three track sliding ) , chequered tiles , caramic tiles , vetrifide tiles , cota stone , marble tiles , granite tiles , red bricks (hat bhatta) , red bricks (round bhatta) , bricksfly aish , peving block 60 mm , peving block 80 mm , rcc compound poles 8ft , rcc compound poles 6 ft , pvc nahani , gally trap15*10 mm , swr pipe 110 mm , screw down bib 15mm , ladies ceramic urinal , wall mounturinal , water close pan complit , indian orissa pan , basin pan , water storage tank500 ltr , water storage tank 1000 ltr , water storage tank 2000 ltr , steel work , mild steel hollow pipe , mild steel i section beam , mild steel c section beam , mild steel angle , cenring kills , nut bolt and washer , profile sheet isi 0.50 mm , profile sheet fancyisi 0.50mm , g.i. sheet , stenless steel seatting bench , mild steel seatting bench , rcc bench , barbed wire / fenshing wire , electric brecker machine , nal toti 1/2 , firweel 1/2 isi , mdpe pipe15 mm , mdpe fta 15 mm , mdpe mta15 mm , mdpe fta lbow 15 mm , mdpe mtalbow 15 mm , mdpe joindar 15 mm , upvcpipe 1/2 isi , upvcmta 1/2 isi , upvcfta 1/2 isi , upvclbow1/2 isi , upvcsoket1/2 isi , water meter isi , pvc pipe 2 4kg isi , pvc pipe 2.5 4kg isi , pvc pipe 3 4kg isi , pvc pipe 4 4kg isi , pvc pipe 5 4kg isi , pvc pipe 6 4kg isi , pvc pipe 3 6 kg isi , pvc pipe 4 6 kg isi , l bo 2 6kg isi , l bo 2.5 6kg isi , l bo 3 6kg isi , l bo 4 6kg isi , l bo 5 6kg isi , l bo 6 6kg isi , pvc bend 2 6kg , pvc bend 2.5 6kg , pvc bend 3 6kg , pvc bend 4 6kg , pvc bend 5 6kg , pvc bend 6 6kg , t 2 6kg isi , t 2.5 6kg isi , t 3 6kg isi , t 4 6kg isi , t 5 6kg isi , t 6 6kg isi , soket2 6kg isi , soket2.5 6kg isi , soket3 6kg isi , soket4 6kg isi , soket5 6kg isi , soket6 6kg isi , mta soket2.5isi , mta soket3isi , mta soket4isi , fta soket2.5isi , fta soket3isi , fta soket4isi , mentanance soket 2 6kg isi , mentanance soket 2.5 6kg isi , mentanance soket 3 6kg isi , mentanance soket 4 6kg isi , mentanance soket 5 6kg isi , mentanance soket 6 6kg isi , saydal 2 6kg , saydal 2.5 6kg , saydal 3 6kg , saydal 4 6kg , saydal 5 6kg , saydal 6 6kg , ball valve pvc 1/2 , ball valve pvc 2 , ball valve pvc 2.5 , ball valve pvc 3 , ball valve pvc 4 , ball valve pvc 5 , ball valve pvc 6 , end cap 1/2 , end cap 1/3 , end cap 2 , end cap 2.5 , end cap 3 , end cap 4 , end cap 5 , end cap 6 , reducer 2/2.5 , reducer 2.5/3 , reducer 3/4 , reducer 4/5 , reducer 5/6 , solution 100 ml , solution 200 ml , solution 500 ml , solution 1 ltr , solution 5 ltr , m sill 100 ml , m sill 200 ml , hole tite 200ml , hole tite 500ml , ruber paking , nut bolt , gi pipe 2isi , gi pipe 2.5isi , gi pipe 3isi , gi l bo 2 isi , gil bo 2.5isi , gi ;l bo 3isi , gi bend 2 , gi bend 2.5 , gi bend 3 , gi t 2isi , git 2.5isi , gi t 3isi , gi soket2isi , gi soket2.5isi , gi soket3isi , flange 2isi , flange 2.5isi , flange 3isi , flange 4isi , flange 5isi , flange 6isi , cid pipe 3 , cid pipe 4 , cid pipe 5 , cid foot bend pipe 3 , cid foot bend pipe 4 , cid foot bend pipe 5 , cid pipe t3 , cid pipe t 4 , cid pipe t5 , cid pipe soket3 , cid pipesoket 4 , cid pipe soket5 , swich valve 2 , swich valve 2.5 , swich valve 3 , swich valve 4 , swich valve 5 , non return valve 2 , bliching , syntax water tank , 1 hp monoblock pump , 1 hp submarshiblepump , 1.5 hp submarshiblepump , 2 hp submarshiblepump , 3 hp submarshiblev4 pump , 5 hp submarshible v4pump , 3 hp submarshible v6pump , 5 hp submarshible v6pump , 7.5 hp submarshiblev6 pump , 1 hp monoblock pump , wire 1 mm isi mark , wire 1.5 mm isi mark , wire 2.5 mm isi mark , wire 4 mm isi mark , service wire 2.5 mm isi mark , service wire 4 mm mark , electric isulation tape , water proffing tape , main switch 15 amp mark , main switch 32 amp mark , main switch 63 amp mark , kitcat 15 amp , kitcat 32 amp , kitcat 63 amp , led bulb 12 watt mark , led bulb 15 watt mark , led bulb 18 wattmark , led bulb 24 wattmark , cfl bulb 30 wattmark , cfl bulb 45 wattmark , moduler bord box 10x12 , moduler bordbox 12x15 , moduler bord box 15x18 , moduler bordbox 4x4 , moduler bordbox 4x6 , moduler bord sweech , moduler bord soket , moduler bord indicator , moduler bord regulator , moduler bord 10x12 , moduler bord 12x15 , moduler bord 15x18 , moduler bord 4x4 , moduler bord 4x6 , m.c.b 15 amp mark , m.c.b 20 amp mark , m.c.b 32 amp mark , m.c.b box , aluminium wire 1.5 mm isi mark , aluminium wire 2.2 mm isi mark , febrication wire 1 mm isi mark , febrication wire 1.5 mm isi mark , cflbulb holder , electric fittingpipe , electric fittingcassing patti , wall mounted fan , fan isi , wire 1/18 isimark , wire 3/20 isimark , wire 7/20 isimark , cable 2 cor isimark , cable 3 cor isimark , cable 4 kovar isimark , led street light 25 watt isi mark , led street light 30 watt isi mark , led street light 45 watt isi mark , led street light 150 watt isi mark , led street light pipe fiting , high mass light 100 vat isi mark , high mass light 150 vat isi mark , high mass light 200 vat isi mark , high mass light 250 vat isi mark , pvc drum 200 ltr , taplon tape , jeevan drop , sodium hypochlorite solution , pvc dust been , pvc dust been , rcc dust been , jarman katori , pendent holder , meter peti , regulator for fan , phenoly , sodium hypochlorite solution , metal door with frame

State Government

TRN :49021348 | 13 May, 2025

Tender Value : 0

Nagpur - Maharashtra

Tender for material supply for all type construction work for year 2025-26 (under all fund) , sand (kanhan) , sand local , soft murun , hard murun , metal 100 mm , metal 80 mm , metal 40 mm , metal 20 mm , metal 10 mm , dust , rcc pipe 300 mm with colar , rcc pipe 450 mm with colar , rcc pipe 600 mm with colar , rcc pipe 800 mm with colar , rcc pipe 900 mm with colar , rcc pipe 1000 mm with colar , cement 53 grade isi mark , still 6 mm , still 8 mm , still 10mm , still 12 mm , still 16 mm , centring tar , vibrator needle , water trankar & tractor troali , backhoe loader , vibrator roller , simple steering road roller , mixchar machine , excavator 70 to 120 , excavator 120 to 220 , fiori 1 cubic meter , fiori 2 cubic meter , centring plate , waterproof compound , acrylic polymer modified liquid , acrylic polymer modified waterproofing powder , fibre glass mesh , plastic emulsion paint , water proof cement paint , lead / zink base oil paint , oil bound distemper , primer , washabe oil bound distemper , putty , birla white cement , terpentine , wood primer , information board still with painting , single lef door 16 mm thik , single lef door 32 mm thik , solid panel pvc internal door shutter , door kittas , door fremas , aluminium fixedwindows (two track sliding ) , aluminium fixedwindows (three track sliding ) , aluminium fixedwindows with mosquito net (three track sliding ) , chequered tiles , caramic tiles , vetrifide tiles , cota stone , marble tiles , granite tiles , red bricks (hat bhatta) , red bricks (round bhatta) , bricksfly aish , peving block 60 mm , peving block 80 mm , rcc compound poles 8ft , rcc compound poles 6 ft , pvc nahani , gally trap15*10 mm , swr pipe 110 mm , screw down bib 15mm , ladies ceramic urinal , wall mounturinal , water close pan complit , indian orissa pan , basin pan , water storage tank500 ltr , water storage tank 1000 ltr , water storage tank 2000 ltr , steel work , mild steel hollow pipe , mild steel i section beam , mild steel c section beam , mild steel angle , cenring kills , nut bolt and washer , profile sheet isi 0.50 mm , profile sheet fancyisi 0.50mm , g.i. sheet , stenless steel seatting bench , mild steel seatting bench , rcc bench , barbed wire / fenshing wire , electric brecker machine

Local Bodies

TRN :49021689 | 15 May, 2025

Tender Value : 86.00 Lacs

Bikaner - Rajasthan

Tender for tender for supply of construction materials gp 20 bd fy 2025-26 - 2 cement ppc3 gravel4 stone 40mm grit (broken by crusher) (cut voids 1/11)5 stone 20mm grit (broken by crusher)6 stone 12/10/6mm grit (broken by crusher)7 brick ballast8 gravel (cut voids 1/6) including transportation from shobhasar quarry9 brick (22x11x7.5 cm) first class10 masonry beradda (rr)11 polished kota stone (one side polished) upto 900 sq. cm12 polished kota stone (one side polished) from 901 to 2300 sq. cm13 polished kota stone (one side polished) more than 2300 sq. cm14 stone chokhat single paitam size 100x75 mm15 jodhpur stone strips upto 1.5 m length, minimum 40 mm thick16 stone strips 1.5 m to 2.40 m length, minimum 50 mm thick17 stone strips 2.4 m to 3.0 m length, minimum 65 mm thick18 stone strips above 3.0 m length, minimum 75 mm thick19 precast tiles glazed size-30x45 cm20 precast tiles mosaic size-40 mm thick21 precast tiles vitrified size-60x60 cm22 cement interlocking block m-30 grade, 60 mm thick23 cement interlocking block m-30 grade, 80 mm thick24 factory made doors (30 mm thick, solid core single leaf)25 structural steel iron (tor steel thm 415/500 for reinforcement)26 winding wire 18 gauge27 iron girders28 conical iron/square iron rods/leaf/angle iron29 iron mesh (24 gauge, 14 mesh)30 glass 3 mm thick31 colour paint enamel paint32 distemper (water bound)33 for lime-paint (aaras/kali)34 primer (for iron/wood)35 g.i. sheet 22 gauge (0.80 mm)36 p.v.c. pipe 90 mm diameter (with ring)37 p.v.c. pipe 110 mm diameter (with ring)38 p.v.c. pipe 140 mm diameter (with ring)39 p.v.c. pipe 110 mm (2.5 kg/sq.cm) with coupler40 centering, shuttering (planking and rigging) for laying rcc roof, slabs, balcony, lintel etc. upto 4.5 m height and removal shuttering ply41 shuttering steel42 transportation of soil for various distances including loading, unloading and stacking of material (length of transportation will be calculated by nearest route and not by road)

State Government

TRN :49022392 | 13 May, 2025

Tender Value : 31.44 Lacs

Gangapur - Maharashtra

Tender for providing electrical installation in, premises street light, water pump and fire extinguisher for the newly constructed zilla parishad primary health center (p .h .c)main building (g.f+f.f) [under scheme d.p.c. (general) year 2022-23, 34512595 construction expantion & m/ce & repairs of p.h.c/ phsc) at village,lasur stationtq. gangapurdist. chhatrapati sambhajinagar.= 1 supplying and erecting 25 mm dia. corrugated flexiblepolypropyleneconduit 2 supplying anderectingpvctrunking (pvccasing-n-capping)ofsize25 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 3 supplying anderectingpvctrunking (pvc casing-n-capping)ofsize20 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 4 supplying anderectingpvctrunking (pvccasing-n-capping)ofsize32 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 5 supplying anderectingpvctrunking (pvccasing-n-capping)ofsize40 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 6 supplying and erecting mains with 2x1.5 sq.mm frlshcopperpvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wg-ma/bw 7 supplying and erecting green earth wire 1x1.5 sq.mm frlshcopperpvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wg-ma/bw 8 supplying and erecting mains with 2x2.5 sq.mmfrlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 9 supplying and erecting green earth wire 1x2.5 sq.mmfrlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 10 supplying and erecting mains with 4x2.5 sq.mmfrlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 11 supplying and erecting mains with 2x4 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 12 supplying and erecting mains with 4x4 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 13 supplying and erecting green earth wire 1x4 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 14 supplying and erecting mains with 4x6 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 15 supplying and erecting pvc insulated pvc round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi strandedcopper industrial cable for voltage grade up to 1.1 kv 16 supplying and erecting pvc insulated pvc round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi strandedcopper industrial cable for voltage grade up to 1.1 kv 17 supplying and erectingceiling rose / batten holder / slanting holder / hanging cord switch / hanging bell push / pendant holder bakelite base 6a. erected on filled polypropylene board or polished double wooden block/ pvc junction box. 18 supplying and erectingmodular type switch 6a / 10a duly erected on provided plate and box with wiring connections complete. 19 supplying and erectingmodular type switch 16aduly erected on provided plate and box with wiring connections complete. 20 supplying and erectingmodular type bell-push with indicator 2 modules 6a / 10a, duly erected on provided plate and box with wiring connections complete. 21 supplying and erectingmodular type 3 pin 6amultisocket with safety shutter, duly erected on provided plate and box with wiring connections complete. 22 supplying and erectingmodular type 3 pin 6 / 16amultisocket with safety shutter,duly erected on provided plate and box with wiring connections complete. 23 supplying and erectingmodular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. 24 supplying and erecting modular type blanking plate one module, duly erected on provided plate & box. 25 supplying and erecting pvc surface modular switch box with double mounting plate for 2module duly erected. 26 supplying and erecting pvc surface modular switch box with double mounting plate for 3module duly erected. 27 supplying and erecting pvc surface modular switch box with double mounting plate for 6module duly erected. 28 supplying and erecting pvc surface modular switch box with double mounting plate for 12module duly erected. 29 supplying and erecting 16 / 20 / 25 a starter (modular range) 2 module for ac unit on provided box complete & duly concealed with necessary material and connected. 30 point wiring for light/bell/exhaust fan in pvc trunking (casing-capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthingand required accessories as per specification no: wg-pw/sw 31 point wiring for ceiling fan in pvc trunking (casing-capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthingand required accessories as per specification no: wg-pw/sw 32 wiring for plug on board withswitch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification no: wg-pw/cw 33 supplying and erectingled square / circular max. 11 w down lighter/panel light having pressure die-cast aluminium housing,polystyrene diffuser havingsystem lumens output of min. 1200 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50,including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 34 supplying and erectingled square / circular max. 14 w down lighter/panel light having pressure die-cast aluminium housing,polystyrene diffuser havingsystem lumens output of min. 1500 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50,including driver,having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 35 supplying and erectingled square / circular max. 18 w down lighter/ panel light having pressure die-cast aluminium housing,polystyrene diffuser having system lumens output of min. 2000 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50, including driver,having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 36 supplying and erectingledpanel light(600mm x 600mm) max. 30 whaving crca powder coated housing,polystyrene diffuser havingsystem lumens output of min. 3600 lumens, min. efficacy of 120 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50including driver,having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 37 supplying and erecting anodized aluminium corridor / passage / mirror light led fitting (2 feet) max. 12wwith high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/w, cri>80, cct upto 6000k, beam angle of 110 deg., ripple<5%,thd<10%,p.f. >0.95, operating range of200-270v, surge protection of 2 kv, life class of 50,000 hrs. at l70b50, including driver with end caps on provided pvc block / wooden board with 3 years warranty. 38 supplying & erecting inverter led batten 10w tube light fitting with polycarbonate housing, heat sink, integrated hf electronic driver, min. 2600 mah lithium ion battery with charging time of 8-10 hours and backup time of min. 3 hrs. with minimum 25% of initial watts having luminous efficacy of 100 lumen/watt,cri>80, cct of 6500k and thd<=20% havinguseful life of minimum 25000 hrs. with overheating protection with 2 years warranty. 39 supplying & erecting inverter led batten 20w tube light fitting with polycarbonate housing, heat sink, integrated hf electronic driver, min. 2600 mah lithium ion battery with charging time of 8-10 hours and backup time of min. 3 hrs. with minimum 25% of initial watts having luminous efficacy of 100 lumen/watt,cri>80, cct of 6500k and thd<=20% havinguseful life of minimum 25000 hrs. with overheating protection with 2 years warranty. 40 supplying and erecting ding dong / electronic musical type call bell with heavy duty coilsuitable to operate on 230v a.c. supply erected on polished double wooden block/sunmica block of suitable size. 41 supplying and erecting integrated led street light fitting26 to 30w ip65 & ik08 class having single piece pressure die-cast aluminium housing ,having system lumens output of min. 2600 lumens, min. efficacy of 100 lumen/w, cri>70, cct upto 6500k, thd<10%, p.f. >0.95, operating range of140-270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50,including driver complete with 3 years warranty as per specification nofg-odf/fls2. 42 supplying and erecting integrated led street light fitting 40 to 50w ip65 & ik08 class having single piece pressure die-cast aluminium housing,havingsystem lumens output of min. 4400 lumens, min. efficacy of 110 lumen/w, cri>70, cct upto 6500k,thd<10%, p.f. >0.95, operating range of140-270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50, including driver complete with 3 years warranty as per specification nofg-odf/fls2. 43 supplying and erecting integratedled street light fitting 100-110w ip65 & ik08 class having single piece pressure die-cast aluminium housing,havingsystem lumens output of min. 11000 lumens, min. efficacy of 110 lumen/w, cri>70, cct upto 6500k, thd<10%, p.f. >0.95, operating range of140-270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50,including driver complete with 3 years warranty as per specification nofg-odf/fls2. 44 supplying & erecting integral post top lantern fixtures (mushroom type) suitable for led lamp upto 12 w consisting of clear acrylic top cover, cast aluminium pole cap complete with accessories on provided pole /bracket as per specification no. fg-odf/ptl 45 supplying and erecting street light wall bracket made from 40 mm. dia ‘ g.i. pipe 1.2 m. in total length complete as per specification no. fg-bkt/wb 46 supplying & erecting 3w, 230v integral type led lamp suitable for b-22 / e-27 base.(night lamp) 47 supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. fg-fn/cf 48 supplying and erecting bracket fan 400 mm. sweep a. c. 230 volts 50 cycles 1350 rpm. oscillating type, plastic or metal blades chrome plated guard with speed regulator and moisture proof treatment to winding and with ‘e’ class insulation. 49 supplying and erecting fresh air cum exhaust fan of light duty 250 v a.c. 50 cycles 300mm. 1400 rpm rust proof body & blades, wire mesh, duly erected, complete. 50 supplying and erecting exhaust fan heavy duty 230 v a.c. 50 cycles 375/380 mm. 1400 rpm complete erected in position as per specification no. fg-fn/exf 51 supplying and erectingenergy saving ceiling fan 230 v a.c. 50 cycles 1200 mm complete erected in position as per specification no. fg-fn/cf 52 supplying and erecting fan hook of 10 mm. m.s. round bar grouted in rcc slab with making the site as original. 53 providing recess in brick wall suitable for erection of exhaust fan up to 450mm. sweep complete with grouting of nut, bolts, plastering and colour washing to match the colour of the wall for the wall thickness of 225 mm. 54 supplying & erecting 22 swg g.i sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 400 mm as per specification no fg-fas/msc 55 supplying and erecting midget type 3.0 litres instant type water heater of rustproof & shockproof abs plastic body, high grade ss inner tank & 3kw heating element with corrosion & hard water protection, with minimum 3 safety protections (i.e. thermostat & thermalcut-out, function valve) complete with 6.5 bar pressure withstanding capacity 230/250v, 50hz, a.c. supply with inlet and outlet, with 3 core pvc flexible copper wire leads duly tested and marking sr. no. and date of erection complete. 56 supplying and erecting chromium plated heavy duty brass stop cock for inlet pipe of water heater (15mm. dia). 57 supplying & erecting 15mm brass non return valve for inlet pipe of storage water heater. 58 providing fiber reinforced pvc flexible pipe upto 1m length with brass locking nuts and washers and clips at both ends suitable for hot water and cold water both (1 set of 2 nos.) complete. 59 supplying, installing, testing & commissioning split type variable speed invertertechnology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3tr to 1.6tr capacity having iseer minimum 3.8 to maximum 4.39 suitable to operate on 250v, 50 hz, a.c. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant r32 having copper condenser, minimum 2.5pm filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dba at position as per specification no. apac/ wac 60 supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7tr to 2.0tr capacity having iseer minimum 3.8 to maximum 4.39 suitable to operate on 250v, 50 hz, a.c. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant r32 having copper condenser, minimum 2.5pm filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dba at position as per specification no. apac/ wac 61 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigerant having 22swg thickness and inner dia/size 12mm complete. 62 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigeranthaving 22swg thickness and inner dia/size 16mm complete. 63 supplying, erecting, testing and commissioning self contained water cooler 230/250v 50hz nominal cooling capacity of 80 litres per hour and storage capacity 120 litres with partially stainless steel body as per specification no. ap-wcr/wc 64 supplying, erecting, testing and commissioning self contained water cooler 230/250v 50hz nominal cooling capacity of 150 litres per hour and storage capacity 150 litres with partially stainless steel body as per specification no. ap-wcr/wc 65 supplying and erecting ultra violet storage type water purifier (ro+uv+uf) with softener for safe drinking water consisting of uv germicidal tube of 8w capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230v, single phase a.c. supply with uv fail & filter change indication system .(for tds more than 200) 66 supplying, installing, testing and commissioning of single phase, 230v, 50 hz, 1400 to 1600va digital pure sine waveinverter with backup time of ........ hrs. based on insulated gate bipolar transistor (igbt) technology completeas per specification no.ap-inv 67 supplying and erecting 12v/180ah tubular battery with battery terminal wire, duly charged with 36 months warranty complete 68 supplying and erecting fully automatic line voltage stabilizer buck and boost type for operation on input voltage 160-270v and output voltage 200-250v rated for 3kva maximum load and with voltmeter, selector switch, 6a/16a flush type 3 pin socket for output and with 3 core copper flexible cord and 3 pin 6/16a plug top with overload & short circuit protection complete. 69 supplying and erecting switch disconnector fuse (sdf) switch 415v, 100a,open execution, four poleac23 a rated with terminal shrouds on both sides and phase barriers along with telescopic shaft for depth adjustments and door interlock and padlock complying to is/iec 60947-3 part-1/3hrc - din type fuse, insulation voltage 1000 vfor enclosing in panel with rotary handle for on / off operation (without hrc fuse) 70 supplying & erecting three phase, 415v, street light control panel up to the max load of 6kw, tpn mcb 40a,powder coated crca 14 swg sheet, outdoor type, having ip54,ik10 protection, suitable rating contactor, 24 hrs. astronomical time switch with minimum 5 years battery back up,auto/manual selector switch, on/off push buttons, indicator lamps, control wiring, metering device, etc. for automatic operation, with overcurrent, short circuit, earth fault protectionon provided iron frame / cc foundation. 71 supplying, erecting & marking spmcb 0.5a to 5a, c-series with rated short - circuit breaking capacity (icn) 10kain provided distribution board as per specification no. sw-swr/mcb 72 supplying, erecting & marking spmcb 6a to 32a, c-serieswith rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 73 supplying, erecting & marking spmcb 6a to 32a, b-series with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 74 supplying, erecting & marking dpmcb 6 a to 32 a, b-series with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 75 supplying, erecting & marking tpmcb 6a to 32a, with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 76 supplying, erecting & marking tpmcb 40a to 63a, with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 77 supplying, erectingand marking double pole isolator only switch version of miniature circuit breakerof40awith required wiring connections and lugs etc. in provided distribution board. 78 supplying, erecting and markingfour pole isolators only switch version of miniature circuit breakers of 40a in provided distribution board. 79 supplying, erecting and markingfour pole isolators only switch version of miniature circuit breakers of 63ain provided distribution board. 80 supplying&erectingtriplepole and neutral distribution board (tpndb), sp/tp mcbs total 4 ways /12 poles, with door, 1.2mm thickness surface/flushmounted, ip 43 protection on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb 81 supplyingand erecting single pole and neutral distributionboard (spndb), with 2 ways for incoming and 6 ways (6 poles) for outgoing sp mcbs, with door, 1.2mm thickness surface / flush mounted, ip 43 protection on iron / gi frame as per specification no. sw-swr/mcbdb 82 supplying & erecting crca sheet metal one way enclosures of 1.2mm thickness suitable for dp mcb /tp mcb/fp mcb/rccb/rcbo complete erected on angle iron/gi frame. 83 supplying & erecting triple pole and neutral distribution board (tpndb), 3 pole/4 pole mccb as incomer & outgoing sp mcb (36 poles) or tp mcb of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb1 84 providing & erecting 4 pole mccb, 415 v, 100a, rated short-circuit breaking capacity 25 ka (ics=100% of icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/uv/trip alarm contact.mccb with phase barriers on both sides, insulation withstand capacity 800v, no line-load bias in provided enclosure/panel as per specification no. sw-swr/mccb (rate of 3 pole mccb +20% for 4 pole mccb= 5309x20%+5309=6370.80) 85 supplying and erecting cupboard for enclosing switchgears orforany other purposemadefromselected marine plywood planks 19 mm thick duly varnished/ painted from inside and from outside with brass hinges and locking arrangement with suitable lock with keys in duplicate. cupboard shall be duly grouted with suitable size of iron work in wall at the bottom. (size of cupboard 0.5x1x2+0.5x1x2+1x1x2= 4 sq.mtrs.) 86 supplyinganderectingiron, sheet metal work consisting of crcasheets, varioussectionsofiron,plates, chequeredplates,rods,bars,mspipes,etc. forpanel board or any other purpose with bending, cutting, drilling and welding completeerectedatthepositionwith necessarymaterialsdulypaintedwith one coat of red oxide and two coats of enamelpaint to match the switchgears or as per directions by the authority. ( 50x50x4mm angle @ 3.4 kgs x 6 mtrs.= 20.40 kgs i,e 20 kgs. 87 supplying and erecting 525 v 3 phase, 50 hz., mpp type capacitor having minimum overcurrent capacity of 1.8 in,peak inrush current capacity 300 inand minimum life 150000 hourskvarbank of all polypropylenecondensers (app)withthestandard capacities of 2, 3, 5, 7, 10, 12.5 and 15 kvarunitsofp.f. correctionforoperationon 3 phase 50 hz. with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and providedwithterminalcoverbox completeerected onprovidediron bracketoronfloordulytestedby licensee.( original p.f=0.8 desired p.f = 0.95 for this multiplying factor is 0.421. so 0.421 x 46.440 = 19.55 i.e 10 kvar x 2= 20 kvar) 88 supplying, erecting & terminating fr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 2 core 6sq. mm. aluminium conductor completeerected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb-lt/al 89 supplying, erecting & terminatingfr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 3½ core50 sq. mm. aluminium conductor completeerected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb-lt/al (double run) 90 supplying, erecting & terminatingfr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 4 core6sq. mm. aluminium conductor completeerected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb-lt/al 91 supplying & erecting g.i. pipe‘a’ class 50 mmdia.erectedfor enclosingxlpearmouredcable on wall/poleas per specification no. cb-ce 92 supplying andlaying (including excavation of suitable width & depth up to 90 cm) 50 mmoutside dia. double wall corrugatedpipes(dwc) ofhdpe for enclosing cable below ground/road surface, to required depth complete. 93 supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mmoutside dia. double wall corrugatedpipes (dwc) ofhdpe for enclosing cable below ground/road surface, to required depth complete. 94 supplying & erectingcast iron cable indicatorplate buried along with route of cable for pvc / xlpe armoured cableas per specification no. cb-cip 95 supplying & erecting frp box of size 150mm x 125mm x 100 mm, 2.7 mm thickcomplete on pole/wallas per specification no. cb-sb 96 providing & erecting 8 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 135 mm a/f, top 70 mm a/f on provided foundation as per specification no. oh-pl/opl 97 providing and erecting galvanised 1000mm single arm sword type bracket with frp dome and ball as per specification no. oh-pl/pbkt 98 providing and erecting galvanised 1000mm double arm sword type bracket with frp dome and ball as per specification no. oh-pl/pbkt 99 providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results asper specification no. ea-ep 100 providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results asper specification no. ea-ep 101 providingpipetype earthing with 40mm. dia. g.i. pipe or 20 mm dia. g.i. rodcomplete with all materials testing and recording the results as per specification no. ea-ep 102 supplying and erecting gi strip of required size used for earthing on wall and/or any other purpose with necessary gi clampsfixed on wall painted with insulating and non-corrosive bond with requiredjointsas per specification no. ea-ep.(25x3mm strip. perpole 1.5 mtrs. so for 13 poles 13nos.x1.5mtrs.= 19.5 mtrs. weight of strip @0.590kgs/mtr. so 19.50mtrs.x0.590kgs.=11.51 kgs.) 103 supplying and erecting minimum three & above star rated 1 phase, 230 v, 50 hz, submersible pump set of 1.5 kw/2hp suitable for erection on open well, pump having delivery head from 29to 7 m and discharge from 30 to 600 litres. . per minute& pipe of suction 50 mm/delivery 50 mm diameter erected with necessary h type clamps as per specification no. wp-osp 104 supplying & erecting flat flexible 3 core 4 sq.mm pvc sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 105 supplying & erecting automatic control panel for 1 ph, 230 volt, a.c. submersible/centrifugal pump set up to 3 hp consisting of dol starter of suitable relay range s.p.p., combined ammeter/ voltmeter, phase indicating lamp enclosed in crca powder coated vibration proof enclosure with ip 54 protection. 106 supplying & erecting carbon dioxide (co2) fire extinguisher of 4.5 kg. capacity cartridge type conform to is 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. m. s. flat with nut & bolts routed in wall complete. 107 making cement concretefoundationin 1:3:6 cement concrete,(20 to 25) mm. stone metal duly plastered with necessary curing forcomplete. (02x02x02 foundation for main control panel stand and for street light control panel 0.2x0.2x0.2mtr.=0.16 cu.mtrs.) 108 makingm- 20 grade reinforced cement concretefoundation by considering the safe soil bearing capacity at site as 10 t/sq.mat 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical gi pole). 109 supplying and erecting isi mark gi pipe 50 mm dia.‘b’ class at position with accessories complete as per specification no. cw-plb/gp. 110 supplying and erecting high density polythene pipe isi mark 50 mm. dia. suitable for pressure of 6 kg. / cm2 connected tojet/submersible pump with required material complete. 111 supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete. 112 supplying and erecting non return valve 50 mm dia in position made of gun metal complete. 113 lum sump provision towards service connection charges1 no.3 phase @ rs. 55000/-/per total rs.55,000/-

State Government

TRN :49023607 | 16 May, 2025

Tender Value : 22.62 Lacs

Lucknow - Uttar Pradesh

Tender for tender for construction and renovation work of community center located in sector-d of kanpur road scheme - rcc repairs 2 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge. 3 75mm average thickness 4 50mm average thickness 5 25 mm average thickness 6 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 7 bars upto 12 mm diameter 8 bars above 12 mm diameter 9 drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in rcc beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer-in-charge.upto and including 12mm dia. 10 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect.epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 11 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge.note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 12 25 mm average thickness in 2 layers. 13 50 mm average thickness in 3 layers. 14 providing and laying sbr polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structuralmembers e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of rcc member.note: rates shall be for finished surface area of concrete and shall include the cost of making holes in existing rcc slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved super-plasticiser forrendering concrete as flowable self compacting and sbr polymer but shall exclude cost of reinforcement, bond coat, shear keys, centering and shuttering, strutting, propping etc (payment under this item shall be madeonly after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) 15 50mm thick in grade m 25 with cement content not less than 330 kg per cum 16 75mm thick in grade m 25 with cement content not less than 330 kg per cum 17 100mm thick in grade m 25 with cement content not less than 330 kg per cum 18 providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge.(the payment shall be made on the basis of actual weight of approved grout injected.) 19 epoxy injection grout in concrete/rcc work of approved make 20 providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the engineerin- charge.wooven pvc cloth 21 shotcreting r.c.c. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stoneaggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by engineer- in-chargenote: rates shall include the providing necessary ground wires etc. the levelling gauges, if used, shall be paid for separately. payment under this item shall be made only after proper wet curing has been done and surface hasbeen satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 22 50mm thick in grade m 25 with cement content not less than 330 kg per cum 23 75mm thick in grade m 25 with cement content not less than 330 kg per cum 24 providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of engineer-in-charge. 25 providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 26 mild steel or iron work in plain work such as in r.c.c. or r.b. (when not included in an over all rates ) including bending for proper completion of the workand including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. 27 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 28 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 29 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thic 30 waterproofing and terracing 31 providing and laying in situ five course water proofing treatment with app (atactic polypropylene) modified polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to is : 702, 3rd layer of roofing membrane app modified polymeric membrane 2.0 mm thick of 3.00 kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron hmhdpe film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron hmhdpe film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 33 miscellaneous works 34 providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, includingadditional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia m.s. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with m.s. tubes, m.s. tube challis, m.s. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of engineer-in-charge.note:- (1) the elevational area of the scaffolding shall be measured for payment purpose. (2) the payment will be made once only for execution of all items for such works. 35 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. 36 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 37 cleaning of under ground sump, over head r.c.c. tank ( independent staging) including disposal of slit and rubbish, all as per direction of engineer-in-charge.the cleaning shall consist following operations:-(i) tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits.(ii) entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water.(iii) chlorination of rcc internal surface by liquid chlorine.(iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.(v) finally the surface shall be treated with ultraviolet radiation etc. as per direction of engineer-in-charge. 38 door-window repair 39 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) 40 renewal of old putty of glass panes (length) 41 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead asper direction of engineer - in- charge. 42 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer-in-charge. 43 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar 44 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres 45 casement door double panel with french (false) mullion with zinc alloy (zamak) 3d hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.using r4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above ) x (100 mm& above) & french (false ) mullion (64mm & above) x (60 mm & above). (height above 2.5 metre) 46 toughened glass 12 mm thickness 47 finishing work 48 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 49 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 50 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 51 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 52 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 53 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 54 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 55 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 56 washrooms 57 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 58 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 59 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including isi marked stainless steel butt hinges with necessary screws 60 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 61 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 62 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

corporations/Associations/Others

TRN :49024378 | 10 May, 2025

Tender Value : 7.20 Lacs

Kanpur - Uttar Pradesh

Tender for tender for 38-construction of mokshdham at gram chakothi block- chakothi - boring of 25cm dia piles of double under reamed of 50cm dia of bulb and 3.60 meter depth in b.c. soil with hand operated auger machine 2 r.c.c . work in cement coarse sand and 20mm gauge stone gride in proportion 1:2:4 in piles grade beam excluding supply of reinforcement and also including supply of all material labour t&p centeringand shuttering etc. 3 r.c.c . work in cement coarse sand and 20mm gauge stone gride in proportion 1:2:4 in columns excluding supply of reinforcement and also including supply of all material labour t&p centeringand shuttering etc. 4 m-150 brickwork in 1:6 cement and fine sand mortor including cost of material , labour, t&p complete 5 m-150 brickwork in 1:6 cement and fine sand mortor including cost of material , labour, t&p complete in super structure 6 r.c.c . work in cement coarse sand and 20mm gauge stone gride in proportion 1:2:4 in lintel t-beam, slab excluding supply of reinforcement and also including supply of all material labour t&p centeringand shuttering etc. lintel 7 m.s. work in r.c.c. incluing supply of steel its wastage and hooks and authorised overlap 8 earth work in filling by cartage of earth from 1.00km by tractor trolly. 9 12mm thick plaster work in 1:4cement and fine sand mortor 10 coarse sandfilling under floor 11 laying of pcc in 1:6:12 cement ,sand and 40mm stone ballast in base concrete 12 laying of 80mm thick rouble moulded interlocking concrete pavment as per drawing and design clause 1501 13 p/applying white cemnent based putty of avg. thickness 1mm of appd. brand over the plastered wall surface to prepare to surface even and smooth 14 finishing wall tex tured exterior paint of required shad : new work ( two or more coat) @3.28ltr /10sqm over and including priming coat of exterior primer applied @2.20kg /10sqm 15 12 mm thick plaster in 1:2 cement and coarse sand mortor over slab 16 site clearence before and after completion the work 17 imformation board + photography 18 installation of hand pump 19 tranpotation of handpump material and t&p from divi. store to site of work 20 hiring charge of necessary t&p and equipment requried for instalation of handpump cutter , wire rope lamps wooden planks ,loading arrengment for palm and presser for com. days including excavation of pit and water etc. complete 21 p/ of india mark hand pump machine and pipe etc 22 standerd deepwell hand pump machine complete 23 140mm pvc pipe 8kg per sqm 24 p/ o 32mm diameter gi pipe b class all completion 25 to make vertical bore 150mm dia boring by hand boring in following depthsin soil mixed with morum /shingle /kankar the depth of bore shall be according to strata condition this shall be decited by eng. i/c 26 0-30m 27 31-50 28 51-60 29 s/f of end cap 110 mm dia required including all material labour t&p 30 s/f of nylon meshrequired including all material labour t&p 31 preparation of assembly as per eng. i/c and lowering of assembly consisting of110mm dia pvc pipe 6kg/sqcm, 1 kg /sqcm, 10 kg /sqcm and testing ets vertically along with stainer pipe fitted at bottom . 32 0-45m 33 45- above bgl 34 s/filling coarse sand arround stainer ( up to 3 mtr. from the bottom of stainer and filling of bentonite between bore hole and casing pipe including all material labour t&p 35 lowring of 32mm dia gi pipe with ets cutting , threding etc. com. 36 development of drilled bore hole sand till free yield of water is achieved in newly constructed bore hole including all material labour t&p etc. com. and installation of india marka ii hndpump (padestal) its position and its centering 37 disaffection by chlorination work of development work of after handpump installation after devlopment including supply of all chemicals required. 38 const. of pcc plateform in 1:2:4 of size 1.85 mtr. dia as deparmental type design for india marka handpumpe 39 const. of pccdrain in 1:2:4as deparmental type design complete 40 embossing on pedestal as per direction of eng.i/c 41 provision for testing of water sample in district water qlty.lab of newly installed handpumpe

Local Bodies

TRN :49028253 | 15 May, 2025

Tender Value : 50.00 Lacs

Barmer - Rajasthan

Tender for supply of building material and equipment in gp barasan ps gudamalani-ghadla/kankar/jhajhra 2 mortar-soil/mud masala 3 lime from kali kiln for masonry work 4 cement 5 p.p.c. 6 white cement 7 fine aggregate 8 sand/gravel 9 fly ash 10 surkhi 11 stone dust (in masonry work) 12 ballast of stone/brick (for other than road work) 13 stone 40mm measured (grit broken by hand) (cut voids 1/11) 14 stone 40mm grit (broken by crusher) (cut voids 1/11) 15 stone 20mm grit (broken by crusher) 16 stone 12/10/6mm grit (broken by crusher) 17 brick ballast 18 material for road work (including 5 km lead) 19 63-40 mm stone crushed stone gravel (cut voids 1/11) 20 63-40 mm hand broken stone aggregate(cut voids 1/11) 21 90-45 mm. hand broken stone aggregate(cut voids 1/11) 22 quarry rubbish(cut voids 1/6) 23 gravel(cut voids 1/6) 24 kankar(cut voids 1/6) 25 binding material (pi 4-6)(cut voids 1/6) 26 brick (22.5 x 11 x 7.50 cm) 27 first class (i st class) 28 second class (ii class) 29 soling/ kharanja/ masonry stone 30 masonry beradda (rr) 31 masonry radda (cr) 32 kharanja soling (for flooring work upto 15cm height) 33 kharanja soling (for road/ kharanja work upto 23cm height) 34 jodhpuri type stone strips/arches/cuts (length 2-3, width 10-12,thickness 2.5-3.5) 35 stone chips (flaky material)(3-4 thick & length and width 1-2) 36 sandstone(dpc,sill,coping,lintel,tand,almirha etc) 37 upto 25mm thickness 38 upto 25-40mm thickness 39 upto 40-50mm thickness 40 upto 50-75mm thickness 41 upto 75-100mm thickness 42 upto 100-150mm thickness 43 flooring / patti pattan katla stone 44 flooring katla upto 35mm thick, min. 3 sqft or more area 45 patti pattan katla 60-75mm thickness, min. 3 sqft or more area 46 unpolished rough kota stone 47 900 sq. cm 48 upto 901 to 2300 sq. cm. 49 above 2300 sq. cm. 50 polished kota stone(one side polished) 51 upto 900 sq. cm. 52 upto 901 to 2300 sq. cm. 53 above 2300 sq. cm. 54 marble stone(makrana adanga 20mm thick) 55 upto 900 sq. cm. 56 upto 901 to 2300 sq. cm. 57 above 2300 sq. cm. 58 marble chips 59 marble powder 60 marble stone(rajnagar ii quality/local 20mm thick) 61 upto 900 sq. cm. 62 upto 901 to 2300 sq. cm. 63 above 2300 sq. cm. 64 stone frame 65 single paitaam size 100 x 75 mm. 66 double pattam size 125 x 75 mm. 67 stone plates 68 up to 1.5 m length, minimum 40mm thick 69 1.5 m to 2.40 m length, minimum 50mm thick 70 2.4 m to 3.0 m length, minimum 65mm thick 71 above 3.0 m length, minimum 75mm thick 73 glazed size-30x45 cm 74 mosaic size-40mm thick 75 vitrified size-60x60 cm 76 interlock tiles/brick/block for road work 77 cement interlocking block m-30grade, 60mm thick 78 cement interlocking block m-30grade, 80mm thick 79 cement interlocking block m-30grade, 100mm thick 80 fr pvc insulated copper conductor single core cable isi marked 81 1.50 sq. mm. 82 2.50 sq. mm. 83 0.50 sq. mm. 84 1.00 sq. mm. 85 4.00 sq. mm. 86 6.00 sq. mm. 87 local wood with fittings (for doors, windows and furniture) 88 mango 89 acacia 90 others 91 factory made doors (30mm thick, solid core single leaf) 92 structural steel 93 iron (tor steel fe 415/500 for reinforcement) 94 winding wire 18 gauge 95 iron girders 96 conical iron/ square bars/ leaf/ angle iron 97 barbed iron wire (size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage 98 mesh 99 iron mesh (24 gauge, 14 mesh) 100 cement concrete mesh akash patal 40mm thick 101 glass 102 3mm thick glass 103 colour paint 104 enamel paint 105 distemper (water bound) 106 lime - for whitewashing (aras / kali) 107 primer (for iron / wood) 108 petroleum products 109 diesel hsd 110 movil oil 111 bitumen shalitex board (25 mm thick) 112 plain sheet 113 g.i. sheet 22 gauge (0.80 mm) 114 g.i. sheet 24 gauge (0.63 mm) 115 m.s. sheet 22 gauge (0.80 mm) 116 m.s. sheet 24 gauge (0.63 mm) 117 corrugated sheet 118 g.i. sheet 1 mm thick 119 gi sheet 22 gauge(0.80 m.m.) 120 asbestos cement sheet 6mm(2.5/2.75x1m) 121 other sheets 122 pvc sheet 1mm thick (coloured/plain) 123 green yellow literof expo sheet(183x90) 124 pipes 125 gi 15mm diameter(b class) 126 gi 20mm diameter(b class) 127 gi 25mm diameter(b class) 128 a.c. 75mm diameter 129 a.c. 100mm diameter 130 p.v.c. 90mm diameter diameter(with ring) 131 pvc 110 mm. diameter(with ring) 132 pvc 140 mm. diameter(with ring) 133 pvc 110 mm.(2.5kg/sq.cm) with coupler 134 sanitary 135 indian w.c. 136 orrisa w.c. 137 european w.c. 138 foot rest 139 porcelain urinal 430350300 mm with coupler, bracket and pvc waste pipe 140 wash-basin 450*300 mm with coupler, bracket and pvc waste pipe 141 stone beam (s.w.) pipe 100 mm. diameter, 0.6 m. long 142 c.p. pillar cock (dia 15 mm) (is mark) 143 c.p. bib cock (dia 15 mm) (is mark) 144 c.p. grating of 125 mm. diameter 145 r.c.c. np3 hum pipe with collar 146 1200 mm dia 147 1000mm dia 148 750mm dia 149 600mm dia 150 450mm dia 151 300mm dia 152 steel conduit isi marked 153 20 mm. diameter 154 25 mm dia 155 charcoal 156 p.v.c. water tank with cover (conforming to is:12701-1989) 157 13/0.20 mm twin core pvc sheathed, flat flexible copper cable 158 steel fasteners 6 mm x 75 mm 159 pvc conduit isi marked 160 25 mm diameter 161 20 mm diameter 162 junction box 163 20 mm two way 164 20 mm one way 165 25 mm two way 166 20 mm one way (pvc) 167 module gi box 168 for 3 modules 169 for 2 modules 170 module base & cover plate 171 for 2 modules 172 3 for module 173 modular switch one way, isi marked 174 sp 15/16 ampere 175 sp 5/6 ampere 176 modular socket outlet, isi marked 177 3 pin 5/6 ampere 178 6 pin 15/16 ampere 179 mcb db 180 2+ 2 way, spn, single door 181 2+4 way, spn, single door 182 2+6 way, spn, single door 183 gi pipe (medium grade) 184 15.00 mm diameter 185 40.00 mm diameter 186 copper wire 8 swg (4.00 mm dia.) (0.117 kg/m) 187 ci/ms cover plate, frame with locking arrangement attached to 188 diesel road roller 8 to 10 ton 189 truck 9 ton 190 tractor (25-40 hp) 191 tractor trolley 192 tractor water tanker capacity 4000 liter water 193 cement concrete mixer 5-7 cubic feet 194 pumping set 15 h.p . 195 niddle/plate vibrator with operator 196 camel cart/bullock cart with driver 197 grinding machine with operator (big, motor driven) 198 compressor 199 hydraulic excavater/jcb ( bucket capacity 0.4 cum) 200 dumper 201 scraper 202 shuttering of wooden plank, with installing tp along with bat and other materials on site, removing it after the prescribed period 203 installing shuttering ply along with bat and other materials on tp site, removing it after the prescribed period 204 shuttering iron plate along with bat and other materials along with tp installation at site, removal after specified period 205 water and pumping charges (filling) 206 grinding machine with operator (small, hand operated) 207 installing iron form for well (diameter 3m, height 75cm) along with tp at site, removing after specified period 208 cultivator

State Government

TRN :49029493 | 15 May, 2025

Tender Value : 32.33 Lacs

Gautam Buddha Nagar - Uttar Pradesh

Tender for construction of e-library room in village begmabad yea. wc-06 - earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom.lifts up to 1.50 m including getting out theexcavated soil and disposal of surplus excavated soil as directed with in a lead of 50m. (most/a.r./yeida) 2 supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos/ lindane emulsifiable concentrate of 20%. (dar/2.34.1/based on uppwd/sor-2020)) 3 diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) : treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 coarse sand) to match the existing floor: with chlorpyriphos/lindane e.c. 20% with 1% concentration (dar/2.35.3.1/based on uppwd/sor-2020)) 4 2.5 cm thick damp proof course with cement and approved coarse sand 1:1½ with and including water proofing as ordered by the engineer incharge in the proportion as specified by the manufacturer including supply of all materials, labour, tools & plants etc. required for proper completion of the work and including proper curing & shutterings as necessary. (uppwd/sor-2020/361) 5 applying a coat of residual petroleum bitumen of grade of vg-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 6 cement concrete with 4cmgauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all material, labour, tools&plants etc required for proper completion of the work. 7 b/w with bricks of class 150 in foundation & plinth in cm 1:4 (based on up pwd sor 2020) cement mortar 1:4 ( 1cement :4coarse sand) 8 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 9 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 10 extra for providing and placing in position 2 nos 6mm dia. m.s. bars at every third course of half brick masonry.uppwd-sor-2020-dar-18/6.15/ 11 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately). all works upto plinth level 12 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately).all works above plinth level upto floor v level 13 centringand shutteringincluding strutting, propping etc. andremoval of form for : foundation footings, base of column 14 centringand shutteringincluding strutting, propping etc. andremoval of form for : lintels, beams, plinth beam, grinder 15 centringand shutteringincluding strutting, propping etc. andremoval of form for : suspended floors, roofs, landings 16 columns, pillars, piers, abutments, posts and struts. (dar/5.9.6/based on uppwd/sor-2020)) 17 edges of slabs and breaks in floors and walls:under 20 cms wide. (dar/5.9.16.1/based on uppwd/sor-2020)) 18 earth work in rough excavation , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per(a.r. )for all kind of soil. 19 steel rainforcement for r.c.c. work including straightening, cutting bending, placing in position and binding all complete upto plinth level thermo-mechanically treated bars of grade fe-500d or more./cold twisted bars. (dar/5.22.6/based on uppwd/sor-2020)) 20 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 21 6mm cement plaster of mix: 1:3 (1 cement : 3 coarse sand)based on up pwd sor 2020 dar-18/13.17 22 15mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 23 finishing walls with acrylic smooth exterior paint of required shade: new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 24 distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade 25 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.dar-18/13.26 26 painting with synthetic enemel paint of approved brand and manufacture to give an even shade: two or more coats on new work. 27 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110mm dia 28 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm (dar/12.42.3.2/based on uppwd/sor-2020) 29 bend 87.5° 110 mm bend (dar/12.42.5.2/based on uppwd/sor-2020) 30 shoe (plain) 110 mm shoe (dar/12.42.6.2/based on uppwd/sor-2020) 31 providing and fixing unplasticised -pvc pipe clips of approved design to unplasticised - pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm (dar/12.43.2/based on uppwd/sor-2020) 32 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.(dar/12.44/based on uppwd/sor-2020) 33 steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.dar-18/10.25.2 34 providing and fixing water closet squatting pan (indian type w.c. pan with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests.up pwd sor-2020-dar 18/17.1.1 35 providing and fixing wash basin with c.l. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:uppwd sor-2020-dar 17.7.1 36 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.20mm od pipes. (dar/18.8.2/based on uppwd/sor-2020) 37 25mm od pipes. (dar/18.8.3/based on uppwd/sor-2020) 38 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 39 32 mm nominal bore. (dar/18.17.2/based on uppwd/sor-2020) 40 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer-in-charge over the rcc slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) after two days of proper curing applying a second coat of cement slurry using 2.75kg! sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge. d) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to is: 2645 and approved by engineer-in-charge including laying glass fibre doth of approved quality in top layer of plaster and finally finishing the surface with trowe’ with neat cement suvr an making pattern ot 300x300 mm square 3mm deep. e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer-in-charge: dar18/22.7.1 41 providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked with cover and suttable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank dar 18/ 18.48 42 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - iii) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.(dar 2018-4.17)based on uppwd sor/2020 43 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600mm (dar/11.41.2/based on uppwd/sor-2020)) 44 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dar/8.31/based on uppwd/sor-2020)) 45 providing and fixing brass bib cock of approved quality: 15 mm nominal bore (dar/18.15.1/based on uppwd/sor-2020)) 46 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 47 providing and fixing nahani trap 75x100mmincluding all complete. 48 20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand-dar-18/13.6.1/p-902 49 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30mm thick including isi marked stainless steel butt hinges with necessary screws. (dar/9.21.2/based on uppwd/sor-2020)) 50 extra for providing isi marked stainless steel butt hinges instead of m.s. pressed butt hinges bright finished of required size with necessary screws. (shutter area to be measured). (dar/9.14/based on uppwd/sor-2020)) 51 renewing panes of glass in door, window & ventilators or fixing in the new work with 3mm thick glass panes fixed with brads & putty includung supply of all material , labour , tools & plants required for proper completion of workuppwd sor 2020/p26/806 52 prroviding and fixing isi mark 3 layer prelaminated particle board conforming to grade 2 type-iii of is-12823/20b laminated with 0.6-0.8 mm thick laminate conforming to is-2046/1995 and balancing lamination of 0.5 mm thick on the back side (size 700750430) including all complete 53 supply of work sb collection office/visitor chain with sheat dxwxh 400400450 mm padded with polyurithane foam complete 54 supply wook at site sb collection executive table of 3 layer prelaminated particle board (wood product) of grade 2 type 2 of is-12823/latest 1830 mm 950 mm 750mm including all complete 55 supplying and filling in plinth with jamuna sand under floors, including watering, ramming, consolidating and dressing complete. dar-18/2.27 56 providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as f7d, f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 57 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design with common burnt clay f.p.s. (non modular) bricks of class designation 7.5.(dar/18.33.1/based on uppwd/sor-2020) 58 providing, laying and jointing glazed stoneware pipes class sp-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (dar/19.1.1/based on uppwd/sor-2020) 59 providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round s.w. pipes including bed concrete as per standard design : (dar/19.2.2/based on uppwd/sor-2020) 60 providing and fixing square-mouth s.w. gully trap class sp-1 complete withc.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (dar/19.4.1/based on uppwd/sor-2020) 61 providing and fixing heavy class ss gratingof approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and ft, ut & fd.size 150 mm x 150 mm 62 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.(dar/17.73.2/based on uppwd/sor-2020)) 63 providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. (dar/17.31/based on uppwd/sor-2020)) 64 providing and fixing ptmt soap dish holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (dar/18.65/based on uppwd/sor-2020)) 65 providing and fixing chicken wire mesh (murga jali) 24 gauge and 20 mesh at junction of rcc and masonry walls including fixing in position with steel nails of 25 mm in length as approved at required as directed by engineer-in-charge, scaffolding etc. complete. (ar/yeida//based on uppwd/sor-2020))½x24 gauge 66 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.(dar/9.101.1/based on uppwd/sor-2020))single rubber stopper 67 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:250x10mm(dar/9.97.2/based on uppwd/sor-2020)) 68 providing and fixing aluminium handles,isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.125 mm (dar/9.100.1/based on uppwd/sor-2020)) 69 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour.25mm nominal bore, weighing not less than 62 gms. (dar/18.75.3/based on uppwd/sor-2020)) 70 providing & fixing of cp heavy duty bottle trap 32mm. (complete complying with relavent standard specification and as directed by the competent authority.) for wash basin&urinal 71 providing and fixing 1 mm thick m.s. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm m.s. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and t- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer up pwd sor-2020-dar-18/10.4 72 construction of granular sub-base by providing close graded material, mixing in mechanical mix plant at omc, carriage of mixed material to work at site, spreading uniform layers with motor grader on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 for grade-1 material. (morth/(ar/yeida/based on uppwd/sor-2020) 73 providing and laying 60mm thick i.s.i. mark factory made cement concrete interlocking concrete paver block made by block making machine with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over and including average 50mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per the direction of engineer-in-charge with conforming to is-15658 and irc:sp:63. (ar/yeida/ based on uppwd/sor-2020) 74 wiring point for light in 1.5 sq. mm. pvcinsulated singlecorecopperconductor cable (inpvcconduit with 1.5sq.mm. frlsh pvc insulated multistrand copperconductor cable as earth wire drawn inside conduit.)and5 amp.flush typeswitch& ceiling rose/angle/batten holderfixedwith3mmthickphenolic laminate backalitesheet withbrass machinescrews andcup washers mounted overexisting m.s.switch boardbox/junction boxwith supplyofallmaterial, labour& t&p etc. requiredforproper completion of the work complete in all respect, as directed by engineer in charge pwd-2018 ps no-174c 75 supply and wiring of submains with 2 nos. of 2.5 sq. mm. frlsh pvc insulated1100 vgrade multistrand singlecore copper conductorcable in 25mm dia heavy duty (2mm thick) pvc conduitwith2 nos 2.5 sq.mm.frlsh pvc insulated multistrand copperconductor cable asearth continuity wire drawn in conduit complete in all respect, as directed by engineer in charge pwd-2018 ps no-261c 76 supply and fixing of power plug with 20 amp./250 voltflush type modularswitchand 5 pin 20 a/250 voltflush typeuniversal modular socket switch on concealed m.sboxincluding supply of allmaterial, labourt&petc. complete in all respect, as directed by engineer in charge .pwd-2018 ps no-1139a 77 s&f surface/flush mounting 8 ways spn distribution board with additional metal door without mcb complete in all respect, as directed by engineer in charge. pwd-2018 ps -1024a 78 s&f of 6 amp to 32 amp. mcb (10 ka) c curve complete in all respect, as directed by engineer in charge.pwd-2018ps -1002cat-a 79 s&f of 40amp. dp mcb (10 ka) c curve complete in all respect, as directed by engineer in charge. pwd-2018 ps no-1010 cat-a 80 providing and fixing circular/ hexagonal cast iron or m.s. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ m.s. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. (dar/10.18/based on uppwd/sor-2020))

Boards / Undertakings / PSU

TRN :48996540 | 13 May, 2025

Tender Value : 1.47 Crore

Matunga - Maharashtra

Tender for repair, renovation, and reconfiguration of lab 1 at the computer engineering and it engineering department, first floor, vjti, matunga, mumbai.= 1 dismantling of existing partitions, wall paneling, etc., all complete as per site requirements, and stacking the usable materials within building premises as directed by the architect/consultant/ engineer-in- charge, etc. complete. (lead upto 100 meters) 2 removal of cement tiles, existing flooring, wall tiles,marble, polished shahabad flooring, dado with or without bed concrete, including stacking the materials as directed, with all leads, lifts, etc., complete. (lead upto 100 meters) 3 dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc. complete. ( lead upto 100 meters) 4 scraping the old paint from the plastered internal surface using a dust-free vacuum paint scraper, followed by coating the entire surface with a mixture of whiting or glue and linseed oil, including the provision of scaffolding, as directed. (the scraping of old paint should be done until the neeru finish of the plaster is achieved.) lead and lift upto 100 meters etc. complete. 5 removing old paint from steel and other metal surfaces and making the surfaces even with hand scrapping, scaffolding etc. complete. 6 removing the existing cement plaster of any thickness without causing dust nuisance, stacking the debris up to a distance of 100 meters, cleaning the site, etc. complete. 7 providing and applying an anti-corrosive chemical to exposed reinforcement of r.c.c. members such as beams, columns, and slabs. this includes one coat of alkaline rust converter (feovert, rusticide, or equivalent) after cleaning the surface with a wire brush, followed by two coats of anti-corrosive, epoxy-based, two-component, zinc-rich primer (materemaco p 130 of basf, phenolic ipnet rb, polyalk flxoprime, or equivalent) for rebar protection on exposed reinforcement. additionally, apply a concrete-penetrating corrosive inhibitor (epco kp-100, polalk ep 113, masterseal 1414 of basf, fosroc, or equivalent) over the adjoining concrete surface. etc. complete. 8 providing and applying a bond coat of approved epoxy resin (masterbrace 1414 of basf, epi bond of krishna conchem, or equivalent) before polymer plaster or concrete to ensure a perfect bond between old concrete and new concrete/polymer plaster surfaces. the bond coat should be applied within half an hour after preparation, conforming to astm c881 type 2. this process includes the use of nylon brushes, scaffolding, labor, etc. complete. 9 providing and applying ready-mix polymer-modified cement mortar with an average thickness of 15mm, using polymer in one or more layers, in a proportion of 1:5:15 (polymer, cement, and quartz sand) as per the manufacturers specifications. the surface should be cured after 72 hours of application using wet gunny bags, etc. complete. 10 providing and applying ready-mix polymer-modified cement mortar with an average thickness of 30mm-50mm, using polymer in one or more layers, in a proportion of 1:5:15 (polymer, cement, and quartz sand) as per the manufacturers specifications. the surface should be cured after 72 hours of application using wet gunny bags, etc. complete. 11 providing and applying a 30mm thick self-curing ceramic polymer microconcrete of an approved make, having a compressive strength above m30, non-shrink, and impermeable, as a filling mortar for load-carrying r.c.c. members in two layers on cleaned concrete surfaces, including honeycomb areas (using manual or mechanical means). the mortar shall be prepared by mixing nicosil c80 and fresh 53-grade cement with the required water-cement ratio to achieve the desired consistency. the application and finishing shall be done by manual trowelling. curing shall be carried out after the initial setting time, in accordance with the manufacturers specifications. the work shall be executed in line with the specifications and as directed by the engineer-in-charge. the work must be carried out by a certified applicator, and the work shall be guaranteed for 5 years. the guarantee shall be provided on a rs. 500/- stamp paper. (the bond coat, as per item no. 08 in the boq, is to be applied before the coating.) 12 providing and applying 12mm thick internal/external ready-mix plaster conforming to is: 4031 (part-4) 1988 and is: 383-1970, in a single coat using cement mortar in a proportion of 1:4, with a special type of polymer additive (approximately 0.4%), on all types of surfaces in all positions, including scaffolding and curing. the plaster shall be followed by a smooth finishing coat of gypsum plaster of 6mm thickness, ensuring an even, smooth surface suitable for painting. complete with necessary curing, scaffolding, and all other related works. 13 providing and applying a priming coat over new/old steel and other metal surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt, and other foreign matter. the surface shall be scoured with wire brushes, fine steel wool, scrapers, and sandpaper, with scaffolding as required, etc. complete. 14 providing and applying priming coat over new wood and wood-based surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt, and other foreign matter, sanding, knotting, scaffolding, etc., complete. (brands such as asian paints, dulux paints, nerolac, berger, royal, or equivalent make.) 15 providing and applying two coats of synthetic enamel paint of approved color to new/old structural steel work and woodwork in buildings, including scaffolding if necessary, cleaning, and preparing the surface (excluding primer coat). etc. complete.(brands such as asian paints, dulux paints, nerolac, berger, royal, or equivalent make.) 16 removing and refixingof doors and windows with frames and stacking the materials as directed, including all leads, lifts, labour, fitting etc., complete. (lead up to 100 meters) 17 providing and laying in pattern 600 mm x 600 mm vitrified tile flooring of 8 to 10 mm thickness and confirming to is 15622-2006 ( group bla) of approved make,quality, shade and pattern for flooring . the tile flooring shall be laid in pattern with 2 mm spacers & tiles fixed in cement mortar of 1:4. the rate shall be including floor chipping to attaining required levels, epoxy grouting of joints using approved matching colour tile grout of epoxy grout, necessary protection of the laid floor, acid wash cleaning for any stains before handover. etc. complete as per the drawing, specification and to complete satisfaction of the engineer. rate to include the wastages as per the pattern indicated in the layouts. brands like kajaria, johnson or similar etc. groove shall be filled with grout of approved shade ( brands like laticrete etc.) as dicectedby the engineer-in-charge. etc. complete. basic rate for tile material- rs. 1440/- per sq.m. 18 providing and fixing skirting, including labor, materials, and all related work, etc., complete. rate for skirting of height up to 150 mm. 19 vinyl flooring for hod cabin:providing and fixing approved color homogeneous flooring, 4mm thick with interlocking system, single-layered flexible spc vinyl flooring (spica by tusker vinyl floorings) in roll form, over the provided i.p.s. or kota stone flooring. the flooring will be fixed using approved adhesive, and all joints will be soldered with pvc rods as per the manufacturer’s specifications. the work will be completed as directed, ensuring proper leveling and cleaning. the roll width will be a minimum of 2.0 meters, and the weight of the pvc flooring will be 90 kg per 30 sqm. as directed and approved by engineer in charge. etc complete. basic rate for vinayl flooring material- rs. 900/- per sq.m. 20 providing and laying vitrified mirror/glossy/matte finish tiles of size 590 mm to 605 mm x 590 mm to 605 mm with a thickness of 8 to 10 mm, conforming to is 15622:2006 (group b1a) from an approved make, shade, and pattern, for dado and skirting in the required positions. the tiles shall be fixed in 1:4 cement mortar, including neat cement float, filling of joints, curing, cleaning, and all related work, etc., complete. basic rate for tile material- rs. 790/- per sq.m. 21 providing second-class burnt brick masonry with conventional/i.s. type bricks in cement mortar 1:6 in the superstructure, including striking joints, raking out joints, watering, scaffolding, and all related work, etc., complete. 22 lowering the debris obtained from breaking and removing cement plaster/burnt brick masonry from the first floor by any means, without causing dust nuisance or damage to the structure. the debris shall be stacked as directed by the engineer-in-charge, including cleaning the site, etc., complete. (lead up to 100 meters.) 23 removing and disposing of debris from the site to a dumping ground outside the vjti premises (in accordance with municipal rules), etc. complete. as directed by the engineer-in-charge. (minimum 6 cu.m debris per trip) 24 providing anti-termite treatment to the wooden frames of doors and windows of the existing building as per i.s. 6313 (part-iii), by drilling 6 mm dia. holes at the four corners on one side and the four corners on the other side, at a downward angle of approximately 45 degrees at the junction of the woodwork and masonry. injecting 150 ml of chlorodane 5% w.c. into each hole and sealing with putty, etc., complete, with a 2-year guarantee on bond paper. 25 providing and applying waterproof melamine polish of the required finish to the woodwork by spray machine, including knotting and preparing an even surface by scraping, applying french polish, scaffolding if required, etc., complete.note: the work is to be executed only with prior approval from the superintending engineer. (brands such as asian paints, mrf melamine or equivalent.) etc. complete. 26 providing and fixing ss t/u/l strip profiles for walls, ceilings, tiles, flooring, main doors, interior decoration, bathrooms, and living rooms, including transportation, wastage, labor, etc., complete.shape: t/u/l profilematerial: ss 304 grade stainless steeldimensions: 8 mm to 12 mmlength: 2440 mm (8 feet), 3048 mm (10 feet)type: t-sectionfinish: polishedposition: interiorcolor options: gold, rose gold, black, silver, champagne, antique hairline, antique copperthickness: 2 mm to 8 mmnote: the shape, pattern, color, and design will be directed by the architect/consultant/or engineer in charge. basic rate for material- rs. 850/- per number. 27 providing and fixing ss t/u/l strip profiles for walls, ceilings, tiles, flooring, main doors, interior decoration, bathrooms, and living rooms, including transportation, wastage, labor, etc., complete.shape: t/u/l profilematerial: ss 304 grade stainless steeldimensions: 16 mm to 32 mmlength: 2440 mm (8 feet), 3048 mm (10 feet)type: t-sectionfinish: polishedposition: interiorcolor options: gold, rose gold, black, silver, champagne, antique hairline, antique copperthickness: 2 mm to 8 mmnote: the shape, pattern, color, and design will be directed by the architect/consultant/or engineer in charge. basic rate for material- rs. 850/- per number. 28 providing and fixing sign boards foor doors:specification for waterproof signage boards (12 x 4 inch)size: 12 inches (l) x 4 inches (h) (with size tolerance is plus or minus 1%)material: high-quality, durable acrylic or pvc boardfinish: glossy or matte finish for clear readabilitywaterproof: weather-resistant, suitable for both indoor and outdoor usedesign: custom text, graphics, or logo engraving/printingmounting: wall-mountable with adhesive backing or screw mountscolors: available in multiple colors with contrast for visibility (e.g., white, black, silver)application: ideal for office cabins, rooms, labs, and other signage needsthis durable, waterproof signboard ensures clear and professional signage in various environments. including wastage, etc. complete. basic rate for material- rs. 460/- per number. 29 providing and fixing of 3d wall panels that can be painted as well.size of each panel: 2 x 2 feet.colour: any color, design, or pattern.features: lightweight, fire-resistant, easily diy, 100% recycled.made from natural bamboo plant fiber, etc., complete. basic rate for material- rs. 450/- per number. 30 providing and fixing wooden decorative fluted wall panels/louvered wall panels:material: high-quality wood (mdf, plywood, or hardwood) with a decorative veneer finish.dimensions: 8 feet x 4-5 inchesthickness: 8 mm - 12 mmdesign: fluted design with vertical or horizontal grooves for a decorative effect.color: multicolor/any colour. (customizable to match interior themes).shape: rectangular panels for seamless installation, etc., complete. basic rate for material- rs. 850/- per number. 31 providing and fixing machine cut mirror polished 16 mm to 20 mm thick telephone black / amba white / cat bary brown / rbi red / ocean brown granite stone partition with rounding the edges etc. complete. one side polishbasic rate for granite material- rs. 2530/- per sq.m. 32 providing and fixing oval-type under-counter wash hand basin of 16-inch x 22-inch size and of special color shade, having telephonic black/colored granite of 180mm thick stone black kadappa framework, including chromium-plated coupling bottle trap. the wash basin should be of cera company or equivalent, model no. 3448, as per the detailed drawing or as directed by the engineer-in-charge, etc., complete. (counter size 1.20m x 0.60m). (brands such as jaquar,kohler or equivalent make.) basic rate for wash basin - rs. 6000/- per number. 33 providing and constructing a granite kitchen platform with the installation of a stainless steel sink (600mm x 450mm) as per the detailed drawing, including vertical polished kadappa stone supports (25 to 30mm thick) on both sides, with a kadappa top (35 to 40mm thick) and a polished granite top (16 to 20mm thick). the platform will feature granite strips at the front and both sides, with two vertical granite supports (15 cm height). the top granite will be 75 cm x 40 cm, including cutting and opening for the sink of the required size in both kadappa and granite. the platform size is 5.00 m x 0.60 m, with a height of 0.75 m, etc. complete with all required finishing. basic rate for ss sink- rs. 6000/- per number. 34 supply and installation of 600x600mm modular metal perforated grid ceiling system (cg-01)the ceiling system shall be supplied and installed as per the specifications provided in the tender document, and in accordance with the directions and approval of the engineer-in-charge. the scope includes complete installation with all necessary materials, components, and finishing to ensure proper execution etc. complete. 35 providing and installation of aluminum frame works for partition with ply on both sides and laminate finish: providing and fixing partition aluminum frame work consist of 25mm x 50mm x 1.2mm thick extruded aluminium box section framework at spacing not exceeding 600mm centre to centre both ways (horizontal and vertical). the framework shall be secured at floor structural ceiling and sill/ lintel level with 25 x 50mm x 1.2mm thick horizontal aluminium section. framework to be secured to floor / walls / columns / ceiling / beams using 75mm metal screws and dowels.acoustic infill: providing & fixing acoustic insulation of approved make to g.i./ aluminum/ ms/ wooden frame partition of 50mm thick rockwool of density 48 kg/m with blanket wrapped in rp tissue suitably affixed to partition framework using where necessary gi binding wire duct tape as indicated in the drawing.outer skin:- providing and fixing 18mm plywood of brands like greenply, century or equivalent. finished with 1 mm thick laminate of approved shade applied on plywood of brands like formice, royal touche or equivalent brand.note: rate is as per aluminum framework with both side ply and laminate. etc. complete. 36 providing and fixing of laminate cladding with ply backing:providing and fixing 12mm bwr plywood (brand: greenply, century, or equivalent), directly fixed to the column. a 1mm thickness laminate of an approved shade, applied on the plywood surface. laminate brands: formica, royal touche, or equivalent. etc complete. 37 providing and installation of glass partition (toughened glass): providing 12mm toughened fixed glass partition including all patch fittings, ensuring smooth and even flush joints between glasses, fixing the same in positions to true line and level, finishing the wall joints with clear silicon sealants, cleaning the surface and ensuring that there are no scratch marks on the glass etc. complete as per drawing and specifications, glass brands should be dorma, ozone or equivalent. 38 providing and installation of glass partition (dgu glass): double-glazed unit glass with air spacer of 6 to 16mm, 95% transparency, etc. complete as per drawing and specifications, dorma or ozone or equivalent. 39 providing and installation of 12mm thick clear toughened glass door with film as required. (d2 - 0.91 x 2.10 m) specification:hardware: door to be complete with hardware to each leaf as follows: hinges: 8 nos. ss ball bearing butt hinges. door closer: concealed door closer with hold open. lock set: dead lock as approved.door handles:900mm ht. 36mm dia d type offset handle on both sides in approved powder coating. door stop: floor mounted door stopper as approved seals: drop down floor seal as approved. security system: na note: all the metal profile sections and hardware finish should match the frame. brands like dorma or ozone or equivalent. etc. complete as per drawing and specifications. 40 providing and installation of d1 - double door two-way sliding motorized door, suitable for door openings up to 1.20 meters with a maximum door weight of 100kg (both leaves). the door offers environmental protection with a working temperature range of -20°c to +50°c and is rainproof. it has a standard opening time of 3-8 seconds, with a remote control operating distance of 100 to 200 feet (depending on line of sight). the opening size is 2.4m x 2.10m, and the glass door size is 1.2m x 2.10m. brands like dorma, ozone, or equivalent, to be installed as per drawing and specifications. etc. complete. 41 providing and installation of d3 - 1.09m x 2.10m (single shutter) 12mm toughened glass door with fixed side panels, including all patch fittings, locking mechanisms, and ensuring smooth, even flush joints between the glass panels. the door is to be fixed in position to true line and level, with wall joints finished using clear silicone sealant. the surface should be cleaned and inspected to ensure there are no scratch marks on the glass. installation to be completed as per drawing and specifications, with brands like dorma, ozone, or equivalent. etc. complete. 42 pop punning: providing and applying of plaster of paris punning(1st quality isi approved pop) over plastered with minimum thickness of 8mm-12mm to existingwall surfaces, ceilings & concrete members etc., to be finished in line and plumb with smooth surface ready to receive paint base. rate to be inclusive of edge protection (gi), fibre mesh for service conduits,hacking wall surfaces for better bonding, cleaning, scrubbing the surface, providing grooves if necessary etc., complete as per architects/consultant/engineer-in-charges approval. brands like gyproc, armstrong, shera or equivalent etc. complete. 43 plastic emulsion paint (leed compliant, low voc): providing and applying plastic emulsion paint finish to walls, partitions, and ceiling surfaces of approved make, color, texture, and shade in two coats, with surface and finish acceptable to the engineer in charge to be achieved within these two coats. any additional coats, if required, shall be at the contractors cost. the work includes preparing existing surfaces by scraping away loose particles, dust, etc., washing and scrubbing, filling cracks with crack filler and binder, cleaning and making the surface dust-free, applying water-based rj london putty as directed, rubbing with sandpaper to smooth the surface, and applying one coat of primer as recommended by the approved paint manufacturer. the work also includes providing necessary scaffolding, cleaning, and protecting the site until handover, as well as masking and protecting all service devices such as switchboards, detectors, etc. the work is to be completed at all heights and leads, as per specifications or as directed by the architect/engineer in charge/consultant. brands like asian paints, berger, or equivalent are acceptable. etc. complete. 44 providing and applying premium decorative wallpaper high-end or custom designs (special finishes, custom patterns)specifications: material: non-woven fabric or vinylroll size: 21 inches wide x 33 feet long (covers 55 sq ft)pattern: various styles (floral, geometric, etc.)finish: matte, gloss, or texturedinstallation: peel & stick or pastefeatures:scratch & water-resistanteasy to clean (wipeable)fade-resistanteco-friendly, voc-freeideal for: living rooms, offices, and accent wallsmaintenance: clean with a damp cloth, no harsh chemicalscustom options: available in various colors and patterns, custom designs upon request. basic rate for wallpaper rs. 600/- per sqm. 45 standing platform (300-450 mm from ffl):construction of a standing platform at a height of 300 mm to 450 mm from the finished floor level (ffl), as per approved dimensions. the platform will be made of 18 mm thick wood (century, greenlam, or equivalent) and finished with wood polish (asian paint wood tec, mrf, or equivalent).materials:frame: mild steel or aluminum, powder-coated for corrosion resistance.surface: high-quality plywood, mdf, or approved materials with a non-slip finish.support: sturdy metal beams or supports for stability.features:height: 300 mm to 450 mm from ffl, as per design.finish: non-slip surface with smooth edges and protective coating.safety: non-slip tread and optional guardrails. etc. complete. 46 stage flooring: supply and installation of interlocking rubber tile flooring at the stage area as per the specifications and drawings provided. the flooring will consist of a 6.0 mm synthetic sport surface, including a =1.50 mm pur protect® treated vinyl surface layer, calendared and grained, supported by a pvc density single closed-cell foam, and reinforced with a fiberglass grid structure. it will feature sanosol treatment for fungistatic and bacteriostatic properties. the flooring will meet the following standards: weight: 3.7 kg/m², impact resistance (en 1517) =8 n/m, abrasion resistance (en iso 5470-1) =350 mg, shock absorption (en14808) =25% (labosport result = 28%), indentation resistance (en 1516) =0.5 mm, ball bounce (en 12235) =90%, vertical deformation (en 14809) =3.5 mm, sliding coefficient (en 13036-4) 80–110, fire (en 13501-1) cfl-s1, anti-viral activity (human coronavirus 229e) – iso 21702 (99.37% after 2 hours), energy return (nf p 90 203) =0.31 m/s, tvoc after 28 days <100 micrograms/m³ (iso 16000-6), floor score®, ce marking, en14904 compliant for multi-sports use, reach compliant, and singapore green label certified. the supply and installation will include making good any damaged surfaces using standard fillers such as birla white cement, cement-based grout, epoxy grout, or mortar, and repainting to match the color.all work will be completed in accordance with the specifications, design, drawings, and the direction of the engineer-in-charge. 47 providing and fixing of overhead storage as per the specifications and drawings provided in the tender document. etc. complete. 48 providing and fixing of surface storageas per the specifications and drawings provided in the tender document. etc. complete. 49 providing and fixing on-site a lab table as per the specifications and drawings provided in the tender document. etc. complete. 50 providing and fixing of office desk/table in faculty lounge as per the specifications and drawings provided in the tender document. etc. complete. 51 providing and fixing of office desk/table in office for hod as per the specifications and drawings provided in the tender document. etc. complete. 52 supply and installation ofhod cabin chair as per the specifications and drawings provided in the tender document. etc. complete. 53 supply and installation of faculty lounge chairs as per the specifications and drawings provided in the tender document. etc. complete. 54 supply and installation of study chairs for labs as per the specifications and drawings provided in the tender document. etc. complete. 55 supply and installation of foldable desklet tables for the seminar hall as per the specifications and drawings provided in the tender document. etc. complete. 56 removingthe exisitng light fixures, fans, wires, cables, swith boards and distribution boards etc. complete. 57 point wiring for independent plug, concealed type in min 20 mm isi marked hms pvc conduit with 1.5 sq.mm (2+1e) fr grade copper wires, modular type switch and socket, earthing and required accessories as per specification no wg-pw/sw. (brands for conduits precision/finolex/pressfit. and for cable barnds should be polycab/finolex/havells. etc. complete 58 point wiring for independent plug, concealed type in min 20 mm isi marked hms pvc conduit with 2.5 sq.mm (2+1e) fr grade copper wires, modular type switch and socket, earthing and required accessories as per specification no wg-pw/sw. (brands for conduits precision/finolex/pressfit. and for cable barnds should be polycab/finolex/havells. etc. complete 59 supplying and erecting flush type shockproof plug socket 6a & 16a (6 pin) with 16a / 25a switch combined with indicator lamp and fuse with gang box on wooden board.make /brand (roma/ legrand,/ greatwhite) etc. complete 60 supplying and erecting isi mark modular type 3 pin 6a / 16a multi socket with safety shutter, duly erected on providedplate and box with wiring connectionsetc.complete. brand : roma/gretwhite/legrand) etc. complete 61 supplying and erecting pvc surface modular double mounting plate 3 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) 62 supplying and erecting pvc surface modular double mounting plate 4 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 63 supplying and erecting pvc surface modular double mounting plate 6 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 64 supplying and erecting pvc surface modular double mounting plate 8 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 65 supplying and erecting pvc surface modular double mounting plate 12 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 66 supplying and erecting regular/ standard model ceiling fan of 1400mm with sweep complete erected in position as per specification no. fg-fn/cf brand /orient/polycab/crompton etc. complete 67 supplying and erecting flush-type ceiling fan regulators and electronic step regulators for ceiling fans (600mm, 900mm, 1200mm, and 1400mm sweep), complete with installation on the provided switchboard. make/brand: roma, legrand, or greatwhite. 68 providing and fixing 36 watt 2x2 light fitingsupplying and erecting square shaped crca /die-cast aluminium powder coated housing led panel light (slim edge-lit) 600x600mm suitable for 36 w-40w includingmotion sensor led light with provision for plane front frame with translucent cover fixed to the housing etc.complete .brand philips/havels/wipro etc. complete 69 supplying and erecting 16 to 32 a dpmcb suitable to fix in 2 module of modular switch in provided box complete & duly concealed with necessary material and connected. (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 70 supplying & erecting triple pole and neutral distribution board (tpndb), 3 pole/4 pole mccb as incomer & outgoing sp mcb (24 poles) or tp mcb of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb1 (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 71 providing & erecting 3 pole mccb, 415 v, 100a, rated short-circuit breaking capacity 25 ka (ics=100% of icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/uv/tripalarm contact. mccb with phase barriers on both sides, insulation withstand capacity 800v, no line-load bias in provided enclosure/panel as per specification no. sw-swr/mccb (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 72 supplying, erecting & commissioning 4 pole rccb 63a, electromagnetic type with 30/100/300 ma sensitivity with earth leakage trip indication complete as per specification no. sw-rccb/rccb. (make/ brand: legrand/ schneider/ l&t/ indo asian) 73 supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, nylon rip cord & grey colour sheathed with fr pvc, conforming to itd specification s/ws 113c laid in provided pvc casing capping/conduit as per specification no. wg-tw etc. complete. cables brands should be polycab/finolex/havells. etc. complete 74 supplying and installing cat-6 cable suitable for networking as per specification no. wg-coc/nc. cables brands should be polycab/finolex/havells. etc. complete. 75 supplying & erecting mains with 2 x 2.5 sq.mm. and earth wire 1.5 sq.mm frlsh pvc copper wire in hms pvc conduit min. 20mm dia. as per specification no: wg-ma/pc.etc complete. brand :polycab/finolex/havels) etc. complete 76 supplying, erecting & terminating xlpe armoured cable 3 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.cb-lt/cu(brand: polycab/ finolex/ havells)note - the quantity of wires for looping the required number of air conditioning units has to be calculated by the contractor with respect to the provided architectural working drawing. etc. complete 77 providing & erecting hot dipped galvanised cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) gi sheet of 150 mm width & 20 mm height complete with necessary hardware. cable tray brands should be profab or equivalent. etc. complete 78 supplying and erecting pvc box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification no: wg-ma/box. etc. complete (make/ brand: legrand/ schneider/ l&t) 79 supply & fixing of aluminum box section to be laid on the floor with all excavation, re-cementing & refinishing civil works to make good in line with the existing floor level respective junctionbox to be fabricated in 16 swg gi sheet with cut out as required for terminating the box sections. shall include pvc conduits from jb to work station powerpoints i)150 x 150x 50 mmgijunction box with cover & cut outs etc. complete. (make/ brand: legrand/ schneider/ l&t) 80 supply of a.c split unit (2 ton) :supply of ac split unit as per the specifications, and drawings provided in tender document. make (carrier/ voltas/ bluestar/ samsung) etc. complete 81 supply of 2 ton casatte ac:2 ton inverter casette ac. cooling capacity 3200-8000 watt. offers uniform 360 degree round airflow, with 4 star energy rating. etc. complete. make (carrier/ voltas/ bluestar/ samsung) etc. complete 82 installation of 2 ton ac split unit etc. complete 83 installation of 2 ton ac cassette unit etc. complete 84 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigerant having 22swg thickness and inner dia/size 22mm complete. etc. complete. material selection should be high quality and from reputed brand as directed by engineer in charge. 85 supply & installation electrical communication cable between indoor to outdoor units.cables brands should be polycab/finolex/havells. etc. complete. 86 providing and fixing in position ms frame stand for a.c. units, floor or wall mounted, with vibration isolation pads and frame to be made out of required ms sections strong enough to hold the weight of the ac unit,and should be lockable, including fixing in position using necessary scaffolding, ladder etc, and painting with two or more coats ofapproved enamel paint on a coat of red oxide etc. complete 87 insulated condensate water drain piping constructed out of pvc / hdpe hard pipeswith 6mm thick nitride insulation, fitting, accessories, bends, elbows, tees, flanges, tapings, wall sleeves, hangers, supports, anchors fasteners and concealed in brickwork or flooring. etc. complete(make: finolex/ astral/ prince) 88 supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided pc / copper pipes having 9 mm thickness and inner diameter / sizes 28 mm for solar water heater/ac system. etc. complete. material selection should be high quality and from reputed brand as directed by engineer in charge. 89 supplying & erecting crca sheet metal enclosures of 1.2mm thickness with 20a, 2 pin plug & earth socket and 20a, 3 pin plug top with 20a/30a single pole mcb having rated short - circuit breaking capacity (icn) 10ka complete erected on angle iron/ gi frame. etc. complete 90 carrying out core cutting of size 3 to 5 dia x 15 length in the c.c./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original. etc. complete 91 supply and installation of roller blindsas per the specifications and drawings provided in the tender document. etc. complete. basic cost for blind cloth fabric material rs.900/- per sq.m. 92 carrying out test for ceramic tiles / vitrified tileswater absorption, modulus of rupture (set of 6 tiles) etc. complete. 93 carrying out test for plywood: determination of resistance to dry heat,determination of moisture content,determination of density,thickness of plywood. etc. complete. 94 carrying out test for test for glue adhesion for plywood etc. complete. 95 carrying out test for hollow / solid /aac blocksdensity test. (set of 3 blocks), compressive strength. (set of 3 blocks), water absorption test (set of 3 blocks) etc. complete. 96 providing and fixing 15 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 97 providing and fixing 20 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 98 providing and fixing 25 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 99 providing and fixing on walls/ceiling/floor 32mm dia cpvc pipe with necessary fittings, remaking good the demolished portion, etc., complete. including removing existing pipeline if necessary and conveying and stacking the same in pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 100 providing and fixing 75 mm dia stabilizer pipe/p.v.c. soil vent/waste pipe with necessary fixtures and fittings, such as bends, tees, single junctions, slotted vent, clamps, etc., complete. 101 providing and fixing 100 mm dia stabilizer pipe/p.v.c. soil vent/waste pipe with necessary fixtures and fittings, such as bends, tees, single junctions, slotted vent, clamps, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 102 providing and fixing 10 cm pvc nahani trap with grating, etc., complete. (brands such as astral, finolex, prince or equivalent make.) basic rate for nahani trap is rs. 380/- 103 providing and fixing c.p. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete. basic rate for pillar cock is rs. 1250/- per number 104 providing and fixing of exhaust fan 150mm crompton/havels/usha or equivalent etc. complete. basic rate for exhasut fan is rs.1000/- per number 105 providing and fixing stainless steel round napkin hanger for bathroom/towel holder for wash basin/napkin holder/bathroom (chrome) b. heavymaterial stainless steel product dimensions 17l x 5w x 19h centimetersfinish type chromeinstallation type wall-mounted shape round including fitting etc. completed.basic rate for material is rs. 320/- 106 providing and fixing premium front glass shelf - bathroom shelf/kitchen shelves wall mounted with frosted and toughen (tradition 6 x 18) chrome including fitting etc. complete. basic rate for material is rs. 650/- 107 providing and installation of 6 mm thick mirror with 6 mm thick ply backing, as per design. the mirror will be supported by stainless steel finished buttons, etc., complete. (the glass brand should be saint-gobain, borosil, or an equivalent make) basic rate for mirror is rs. 1250/- per sq.m. 108 supply and installation of nsd make smoke detectormodel:66a, certification: ce & ertl etc. complete. 109 supply and installation of nsd make heat detectormodel:66h, certification: ce & ertl etc. complete. 110 supply and installation of response indicator make: nsdmodel: p.s (mini) etc. complete. 111 supply and installation of manual call point (m.s) make nsd 112 supply and installation of 08 zone fire alarm panel make nsd(excel) etc. complete. 113 supply and installation of flasher hooter make nsdmodel no: ms17flash etc. complete. 114 supply and installation of supply & laying 1.0 sq. mm x 2 core copper armored isi cable for alarmsystem. with accessories per meter. brand/make :polycab/finolex/havellls) etc. complete. 115 supply and installation of high quality co2 fire extinguisher (6 kg)type:carbon dioxide (co2) fire extinguisher (for electrical fires and flammable liquids)capacity: 6 kgfire rating: class b (flammable liquids) class c (electrical fires)material: cylinder: steel or aluminum alloyfinish: red powder-coated for durabilityoperating pressure: 55 bardischarge time: approx. 8-10 secondsdischarge range: 3-5 feettemperature range:operating: -10°c to +60°c storage: -30°c to +60°cmounting: includes wall bracket certification: is 15683 (india) / ul/ce certified etc. complete.note: the rates for all fire safety alarm items include the complete supply, installation, commissioning, transportation, freight, and all associated costs. 116 providing architectural/ interior design services : scope of work as below:drawings preparation: 3d views, floor plans, furniture layout, electrical layout, ceiling layout, and partition layout.color scheme & material selection: guidance on colors and material choices for finishes, flooring, and furniture.quality control: ensure standards for structural, civil, electrical, fire safety, furniture work and hvac work.interior planning: optimize lab functionality and aesthetics, including furniture, partition design, and system planning (electrical, hvac, fire safety).modifications: suggest changes to designs based on site conditions and client feedback.coordination & monitoring: ensure project progress and timely completion by working closely with contractors. deputation of interior designer degree/diploma/certificate course having knowledge of autocad and 3d home or equivalent for the full period of the work. designes. monitor on-site execution, ensuring design adherence. taking joint measurements.preparing statements for extra items and excess quantities.compliance & safety: ensure adherence to safety codes and regulations. etc. complete.

State Government

TRN :48899058 | 14 May, 2025

Tender Value : 1.85 Lacs

Kolkata - West Bengal

Tender for e-tender for repairing, painting, floor cleaning ,polishing, electrical wiring & wood work of mess at bt lines, 29/1 bt road, during the year 2024-2025.= 1 estimate for repairing, painting, floor cleaning,polishing, electrical wiring & wood work of mess at bt lines, 29/1 bt road, during the year 2024-2025. 2 stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 3 cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, i.r.c. fabric mesh or x.p. m. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting i.r.c or x. p. m. & cost of all handling and scaffolding complete as per direction of engineer-in -charge. b) 25 mm thick 4 a) applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per manufacturers specification [cement to be supplied by the department] 5 cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the engineer - in - charge 6 plaster (to wall, floor, ceiling etc.) with sand and cement mortar including round off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/stagingwhere necessary (ground floor). [excluding cost of chipping over concrete surface](i) with 1:6 cement mortar(c) 15 mm thick plaster 7 (ii) with 1:4 cement mortar (c) 10 mm thick plaster 8 (b) rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand (1.5mm thick) 9 acrylic distemperto interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface. two coats 10 supplying best indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (in all floors for internal wall & upto 6 m height for external wall) (i) 3 mm thick (weighing 7.4 kg/sq.m) 11 dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m(a) upto 150 mm. thick 12 ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant is codes. a) pakur variety 13 supplying, fitting & fixing 1st quality ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(a) floor with sand cement mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 kg/sq.m & joint filling using white cement slurry @ 0.20kg/sq.m. (a) area of each tile upto 0.09 sq.m (i) coloured decorative 14 (b) wall with sand cement mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 kg/sq.m & joint filling using white cement slurry @ 0.20kg/sq.m. (a) area of each tile upto 0.09 sq.m (i) coloured decorative 15 (a) painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary:(a) on timber or plastered surface:with super gloss (hi-gloss)- (iv) two coats (with any shade except white) 16 labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (concrete and brick work for mending damage will be paid separately) (a) upto area 2.5 sq.m 17 wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, iron butt hinges and m.s clamps. (the quantum should be correted upto three decimals). (c) sal : siliguri. 18 supplying, fitting and fixing m.s. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction. (cost of concrete will be paid separately) (c) 40mm x 6mm, 125mm length 19 iron butt hinges of approved quality fitted and fixed with steel screws, with isi mark. (viii) 100mm. x 75mm. x 3.50mm 20 supplying,fitting & fixing of 2-track / 3-track aluminium sliding window of all aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to is 733-1983 & is 1285-1975, annodised conforming to is 1868-1983, fitted with all other accessories viz. pvc roller, epdm gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of engineer-in-charge. 10-12 micron thickness annodizing film for 2-track window: members for bottom frame @ 0.875 kg per mtr. and for top and side frame @ 0.778 kg per mtr. and for shutter bottom and top member @ 0.472 kg per mtr., style side member @ 0.493 kg per mtr. and interlock member @ 0.612 kg per mtr. [note : for estimate purpose construction wing may consider weight of 2- track aluminium window @ 5.5 kg per sq.m.and 3-track aluminium window @ 6.5 kg per sq.m] 21 polishing only of old marble or terrazo work with oxalic acid powder using 33 gms/ sq.m. by manual labour / machine where necessary. 22 supply & fixing 240 v, 6 a, 3 pin modular type plug socket (legrand/l&t) with 6a modular type switch, without plug top on 4 module gi modular type switch board with 3 module top cover plate flushed in wall incl. s&f switch board and cover plate and making necy. connections with pvc cu wire and earth continuity wire etc. (for seperate plug) 23 distribution wiring in 1.1 kv grade 2x22/0.3 (1.5 sqmm) single core stranded fr pvc insulated & unsheathed copper wire (brand approved by eic) partly in 20mm size pvc rigid conduit fr (precision make) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for vertical run embedded in wall],with 1x22/0.3 (1.5 sqmm) single core stranded fr pvc insulated & unsheathed copper wire for ecc, to light/fan/call bell points with modular type switch (brand approved by eic) fixed on modular gi switch board complete with 2 no. suitable size “ph & n” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [pvc rigid conduit only for horizontal run & above false ceiling and vertical run concealed](b) average run 6 mtr 24 (a) supply & fixing 240 v, 6 a, 3 pin modular type plug socket (brand approved by eic) with 6a modular type switch, without plug top on 4 module gi modular type switch board with 3 module top cover plate flushed in wall incl. s&f switch board and cover plate and making necy. connections with pvc cu wire and earth continuity wire etc. 25 supply & fixing 240 v, 3 nos. 16 a, 3 pin modular type plug socket with 3 nos. 16a modular type switch (brand approved by eic), 20a modular switch type sp mcb (c-curve) and indicator without plug top on 12 module gi modular type switch board with 12 module top cover plate flushed in wall incl. s&f switch board and cover plate and making necy.connections with pvc cu wire and earth continuity wire etc. 26 supplying,fitting and fixing approved brand 32 mm dia.p.v.c. waste pipe, with pvc coupling at one end fitted with necessary clamps.(iii) 900 mm long 27 sub total 28 gst 18% 29 lwc 1%

Related Searched Keywords : wire mesh shutter

List of wire-mesh-shutter Tenders

Get wire mesh shutter Tender Alert...

Related Searched Keywords : wire mesh shutter

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us