Filters

List of tool Tenders

List of latest tool Tenders in Indian Tenders. Click on any tool Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for tool Tenders.

All-Tenders (80)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49024279 | 14 May, 2025

Tender Value : 0

Firozabad - Uttar Pradesh

Tender for tender for repair work in government high school niyamatpur firozabad under alankar yojana - dismantling doors and windows leaves including chaukhats but excluding hold fasts and including stacking of materials as directed by engineer-in-charge within a distance of 60 meters (200 feet) ch-17 -si no. 15 (705) 2 dismantling existing plaster including disposal of refuse as directed by engineer-in-charge within a distance of 60 meters. ch-17 -si no. 16 (706) 3 earthwork in excavation in trenches for foundation pipes cable etc. in ordinary soil, including lift upto 1.5 m lead upto 50 m and dressing of sides and ramming of bottom and disposal of surplus excavated earth including all labour, t&p etc. for proper completion of work, as directed by engineer incharge. (si. no. 251) 4 class-150 brick work in 1:3 cement and coarse sand of 1.25 fm mortar in super structure including necessary moulding and cutting of bricks as required including supply of all materials, labour and t&p etc. required for proper completion of the work thickness of wall of half brick thick.ch-6 -si no. 2(6.1) 5 providing and laying in cement concrete 1:1.5:3(1cement:1.5 fine sand:3 graded brick aggregate 20 mm nominal size) and curing complete including cost of formwork in foundation and floors. (si. no. 275) 6 providing and laying in cement concrete 1:4:8 (1cement:4fine sand:8graded brick aggregate 40 mm nominal size) and curing complete including cost of formwork in foundation and floors. (si. no. 275) 7 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) door chaukhats above 1.5 sq.m. and upto 5 sq.m. 8 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) window chaukhats above 1.5 sq.m. and upto 5 sq.m. 9 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) ventilator chaukhats above 1.5 sq.m. and upto 5 sq.m. 10 provinding and fixing glass panes with putty and glazing clips in steel doors, windows,clerestory windows all complete with : 4.0 mm thick panes.ch-9 -si no. new(14) 11 mild steel or iron work in heavy sizes such as built up gates record rack, roof work, gates etc. brought to required form including drilling holes revitting or welding where necessary, and also including supply of steel bolts, nuts, wastage etc. and their fixing require for proper completion of the work. ch-10 -si no. 2, (503) 12 mild steel and iron work of small size and section such as holding down woods, hold fasts tierods, grating, etc. (when not included in and over all rates) brought to required form including supply of steel and its wastage including cost of bolts, nuts if required for proper completion of work including fabrication of holes in door chaukhats and nosing. ch-10 -si no. 3, (502) 13 providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.with out base concrete ch-14 -si no. 24 (11.41) same as above but for 600x600mm size. 14 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : ch-13 -si no. 18(14.1) (b) with cement mortar 1:4 (1cement: 4 coarse sand) 15 12 mm cement plaster 1:4 (1 cement and 4 finesand) in single coat on fair side of single or half brick wall for interior plastering upto floor two level including internal rounded angels chamfers, and/or rounded angles not exceeding 80 mm. in girth and finished even and smooth. no extra for mixing any additive. (ch. 13 item no. 13.4 newly surface. 16 finishing walls with one coat of waterproof cement paint of approved quality on previously old treated surface with this paint to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powder material including curing and cost of all materials. ch. 15 item no. 19.29 17 finishing walls with one coat of waterproof cement paint of approved quality on previously old treated surface with this paint to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powder material including curing and cost of all materials. ch. 15 item no.662 18 providing & applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ch. 15 item no. 31-new 19 one priming coat & two coat oil distemper on new work including supply of all materials, labour, t&p etc. required for proper completion of work. paint to be used should confirm isi no. 103-1950. (si. no. 9+10-682) chapter -16 20 painting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.( ch-15 ,2-19.29 +3-642) 21 painting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.( ch-15 si no 3-642 ) 22 providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests. 23 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c. p. brass pillar taps 24 supply & fixing of 11 cm (4) internal dia. pvc down pipes complete with rosehead, bends and gratings & including supply of necessary m.s. clamps 2.5cmx 3 mm1x 1/8) fixed to walls, with & includiug supply of 15cm (6) long 6 mm(1/4) dia. nails & including supply of all material labour and t&p etc. required for proper completion of the work & also including repair of plaster,pointing etc. if damaged during fixing of pipes. details of 30 length. toilet waste water 25 note - 1. cost of maintenance of road for five years will be paid as per g.o. no. 17/2024 sa-113/23-1-2024-23-1099/113/2023 date 16-01-2024 2. the departmental road roller if spare, shall be made available to the contructior at site @ rs. 2500 per day shall be made from contractors bell for idle period 3.payment of maintenance shall be made as per final execution of civil work wich may vary from the boq.

State Government

TRN :49026360 | 21 May, 2025

Tender Value : 0

Kangra - Himachal Pradesh

Tender for tender for supply of building material sand, gravel, crusher, crusher sand, boulder, gutka rate cft broken stone brick abble, brick dom per number. settering iron and wood per sqf, cement opening civil supply sign board making 3x2, 4x3 per bag from sidhpur sarkari store, material hauled by horses concrete bench length 5 feet long with back, water cooler 40 liter with water tank include installation charge., sb merry go round with steel seat, sb chain swing double, sb slider (10ft), sb sea double, sb rainbow(6ft) monkey bar, sb bridge ladder, leg shaper double, waist trimmer double, triple twister, air walker, single skier, bicycle, push up bar, abdominal board, jcb, chairs on rent per hour, tea cup and samosa rate per hour, cake mixer per hour, wall painting 3x2, 4x3 rate per foot. des work level per foot tess work material tin seat, channel, angle, sq pipe, round pipe per kg door window wood and aluminum rft office furniture cupboard, table, ceiling fan chairs plastic

Government Departments

TRN :49026423 | 13 May, 2025

Tender Value : 0

Hazira - Gujarat

Tender for tender for structure dismentaling work at pwh_crm1 2000167357 10 10 10 dismantling of structure 200 to email : hitesh.prajapati@amns.in contact : name : hitesh prajapati item details : * scope of work for vendor: -dismantling existing structures as per requirement. -tools, tackles, grinding m/c etc. -supply of manpower with proper ppes -welding m/c, cutting set, cylinders. -consumables like welding electrodes, grinding wheels. -supervisor in contractor scope -job to be done as per instructions by line in-charge only. * scope of work- amns:- - essentials like electricity, water etc. - crane and hydra will be provided if required. - scaffolding or man lifter will be provided if required. - vehicle will be provided for scrap loading and disposal work. - specific penalty for safety violation and non-performance by vendor. specific penalty for nonperformance by vendor and must be cardinally measured. amns safety rule and regulation as per company policy: • all the persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(cnh). • all the workers have authorized work at height valid pass. • work should be started only after taking authorized work permit. • toolbox talk must be delivery before starting the job on daily basic. • use certified portable hand electric machine. • use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • the person who is working at height should wear certified double lanyard full body harness (safety belt) <(>&<)> locked safety belt (both clamp) with lifeline. anchoring point must be check before every use. • use only certified two lanyards connected in a y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • ensure that all persons are wearing safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / for job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • work should be carried out in close supervision of competent supervisor. • the working at height job should be allowed in daytime only • while handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • while fabrication activity ensure crane movement. crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from page 2 of 2 arcelormittal nippon steel india pvt ltd am/ns hazira plant 27th km, surat-hazira road,,hazira,394270,gujarat,india gstin 24aaace1741p1zn pan aaace1741p cin u27100gj1976ftc013787 request for quotation number 6000133471 date 05.05.2025 submission date 13.05.2025 coll req no amns deals with oems directly. we are very well equipped in every way to import / buy our goods directly from oems from any part of the world in a professional manner. we also use the vast global networks of our parent companies where necessary. we do not welcome any contact from intermediaries or indian agents of vendors. we assure all oems that you do not need to engage anyone to manage your transactions with us.kindly respond to our rfqs and deal with our officials directly without involving any agents or intermediaries. offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. contact for this rfq mr. venkat sai taneeru contact email venkat.taneeru@amns.in materials / services please acknowledge receipt of the rfq and provide your best quote for below given rfq details. sr. no pr no. pr item rfq item services for line item quantity uom technical details other details working area. • while fabrication activity near dsl side, ensure dsl power supply must be cut off <(>&<)> for that lototo must be taken for isolation of dsl power supply. • while fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • while scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • the working area need to be cleaned to avoid the slipping hazards. • ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • always carry fe near workplace. • never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • ensure loose cylinder should not be kept at shop floor. • no oxygen or acetylene gas shall be used for pressure testing purpose. • no oxygen or acetylene gas shall be used for cleaning purposes. • always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. sop no:- amnsil/crm/pwh/19/sop/05 hirac no:- amnsil/crm/pwh/16.7/hirac/39

State Government

TRN :49029493 | 15 May, 2025

Tender Value : 32.33 Lacs

Gautam Buddha Nagar - Uttar Pradesh

Tender for construction of e-library room in village begmabad yea. wc-06 - earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom.lifts up to 1.50 m including getting out theexcavated soil and disposal of surplus excavated soil as directed with in a lead of 50m. (most/a.r./yeida) 2 supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos/ lindane emulsifiable concentrate of 20%. (dar/2.34.1/based on uppwd/sor-2020)) 3 diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) : treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 coarse sand) to match the existing floor: with chlorpyriphos/lindane e.c. 20% with 1% concentration (dar/2.35.3.1/based on uppwd/sor-2020)) 4 2.5 cm thick damp proof course with cement and approved coarse sand 1:1½ with and including water proofing as ordered by the engineer incharge in the proportion as specified by the manufacturer including supply of all materials, labour, tools & plants etc. required for proper completion of the work and including proper curing & shutterings as necessary. (uppwd/sor-2020/361) 5 applying a coat of residual petroleum bitumen of grade of vg-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 6 cement concrete with 4cmgauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all material, labour, tools&plants etc required for proper completion of the work. 7 b/w with bricks of class 150 in foundation & plinth in cm 1:4 (based on up pwd sor 2020) cement mortar 1:4 ( 1cement :4coarse sand) 8 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 9 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 10 extra for providing and placing in position 2 nos 6mm dia. m.s. bars at every third course of half brick masonry.uppwd-sor-2020-dar-18/6.15/ 11 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately). all works upto plinth level 12 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately).all works above plinth level upto floor v level 13 centringand shutteringincluding strutting, propping etc. andremoval of form for : foundation footings, base of column 14 centringand shutteringincluding strutting, propping etc. andremoval of form for : lintels, beams, plinth beam, grinder 15 centringand shutteringincluding strutting, propping etc. andremoval of form for : suspended floors, roofs, landings 16 columns, pillars, piers, abutments, posts and struts. (dar/5.9.6/based on uppwd/sor-2020)) 17 edges of slabs and breaks in floors and walls:under 20 cms wide. (dar/5.9.16.1/based on uppwd/sor-2020)) 18 earth work in rough excavation , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per(a.r. )for all kind of soil. 19 steel rainforcement for r.c.c. work including straightening, cutting bending, placing in position and binding all complete upto plinth level thermo-mechanically treated bars of grade fe-500d or more./cold twisted bars. (dar/5.22.6/based on uppwd/sor-2020)) 20 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 21 6mm cement plaster of mix: 1:3 (1 cement : 3 coarse sand)based on up pwd sor 2020 dar-18/13.17 22 15mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 23 finishing walls with acrylic smooth exterior paint of required shade: new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 24 distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade 25 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.dar-18/13.26 26 painting with synthetic enemel paint of approved brand and manufacture to give an even shade: two or more coats on new work. 27 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110mm dia 28 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm (dar/12.42.3.2/based on uppwd/sor-2020) 29 bend 87.5° 110 mm bend (dar/12.42.5.2/based on uppwd/sor-2020) 30 shoe (plain) 110 mm shoe (dar/12.42.6.2/based on uppwd/sor-2020) 31 providing and fixing unplasticised -pvc pipe clips of approved design to unplasticised - pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm (dar/12.43.2/based on uppwd/sor-2020) 32 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.(dar/12.44/based on uppwd/sor-2020) 33 steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.dar-18/10.25.2 34 providing and fixing water closet squatting pan (indian type w.c. pan with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests.up pwd sor-2020-dar 18/17.1.1 35 providing and fixing wash basin with c.l. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:uppwd sor-2020-dar 17.7.1 36 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.20mm od pipes. (dar/18.8.2/based on uppwd/sor-2020) 37 25mm od pipes. (dar/18.8.3/based on uppwd/sor-2020) 38 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 39 32 mm nominal bore. (dar/18.17.2/based on uppwd/sor-2020) 40 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer-in-charge over the rcc slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) after two days of proper curing applying a second coat of cement slurry using 2.75kg! sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge. d) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to is: 2645 and approved by engineer-in-charge including laying glass fibre doth of approved quality in top layer of plaster and finally finishing the surface with trowe’ with neat cement suvr an making pattern ot 300x300 mm square 3mm deep. e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer-in-charge: dar18/22.7.1 41 providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked with cover and suttable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank dar 18/ 18.48 42 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - iii) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.(dar 2018-4.17)based on uppwd sor/2020 43 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600mm (dar/11.41.2/based on uppwd/sor-2020)) 44 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dar/8.31/based on uppwd/sor-2020)) 45 providing and fixing brass bib cock of approved quality: 15 mm nominal bore (dar/18.15.1/based on uppwd/sor-2020)) 46 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 47 providing and fixing nahani trap 75x100mmincluding all complete. 48 20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand-dar-18/13.6.1/p-902 49 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30mm thick including isi marked stainless steel butt hinges with necessary screws. (dar/9.21.2/based on uppwd/sor-2020)) 50 extra for providing isi marked stainless steel butt hinges instead of m.s. pressed butt hinges bright finished of required size with necessary screws. (shutter area to be measured). (dar/9.14/based on uppwd/sor-2020)) 51 renewing panes of glass in door, window & ventilators or fixing in the new work with 3mm thick glass panes fixed with brads & putty includung supply of all material , labour , tools & plants required for proper completion of workuppwd sor 2020/p26/806 52 prroviding and fixing isi mark 3 layer prelaminated particle board conforming to grade 2 type-iii of is-12823/20b laminated with 0.6-0.8 mm thick laminate conforming to is-2046/1995 and balancing lamination of 0.5 mm thick on the back side (size 700750430) including all complete 53 supply of work sb collection office/visitor chain with sheat dxwxh 400400450 mm padded with polyurithane foam complete 54 supply wook at site sb collection executive table of 3 layer prelaminated particle board (wood product) of grade 2 type 2 of is-12823/latest 1830 mm 950 mm 750mm including all complete 55 supplying and filling in plinth with jamuna sand under floors, including watering, ramming, consolidating and dressing complete. dar-18/2.27 56 providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as f7d, f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 57 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design with common burnt clay f.p.s. (non modular) bricks of class designation 7.5.(dar/18.33.1/based on uppwd/sor-2020) 58 providing, laying and jointing glazed stoneware pipes class sp-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (dar/19.1.1/based on uppwd/sor-2020) 59 providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round s.w. pipes including bed concrete as per standard design : (dar/19.2.2/based on uppwd/sor-2020) 60 providing and fixing square-mouth s.w. gully trap class sp-1 complete withc.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (dar/19.4.1/based on uppwd/sor-2020) 61 providing and fixing heavy class ss gratingof approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and ft, ut & fd.size 150 mm x 150 mm 62 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.(dar/17.73.2/based on uppwd/sor-2020)) 63 providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. (dar/17.31/based on uppwd/sor-2020)) 64 providing and fixing ptmt soap dish holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (dar/18.65/based on uppwd/sor-2020)) 65 providing and fixing chicken wire mesh (murga jali) 24 gauge and 20 mesh at junction of rcc and masonry walls including fixing in position with steel nails of 25 mm in length as approved at required as directed by engineer-in-charge, scaffolding etc. complete. (ar/yeida//based on uppwd/sor-2020))½x24 gauge 66 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.(dar/9.101.1/based on uppwd/sor-2020))single rubber stopper 67 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:250x10mm(dar/9.97.2/based on uppwd/sor-2020)) 68 providing and fixing aluminium handles,isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.125 mm (dar/9.100.1/based on uppwd/sor-2020)) 69 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour.25mm nominal bore, weighing not less than 62 gms. (dar/18.75.3/based on uppwd/sor-2020)) 70 providing & fixing of cp heavy duty bottle trap 32mm. (complete complying with relavent standard specification and as directed by the competent authority.) for wash basin&urinal 71 providing and fixing 1 mm thick m.s. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm m.s. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and t- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer up pwd sor-2020-dar-18/10.4 72 construction of granular sub-base by providing close graded material, mixing in mechanical mix plant at omc, carriage of mixed material to work at site, spreading uniform layers with motor grader on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 for grade-1 material. (morth/(ar/yeida/based on uppwd/sor-2020) 73 providing and laying 60mm thick i.s.i. mark factory made cement concrete interlocking concrete paver block made by block making machine with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over and including average 50mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per the direction of engineer-in-charge with conforming to is-15658 and irc:sp:63. (ar/yeida/ based on uppwd/sor-2020) 74 wiring point for light in 1.5 sq. mm. pvcinsulated singlecorecopperconductor cable (inpvcconduit with 1.5sq.mm. frlsh pvc insulated multistrand copperconductor cable as earth wire drawn inside conduit.)and5 amp.flush typeswitch& ceiling rose/angle/batten holderfixedwith3mmthickphenolic laminate backalitesheet withbrass machinescrews andcup washers mounted overexisting m.s.switch boardbox/junction boxwith supplyofallmaterial, labour& t&p etc. requiredforproper completion of the work complete in all respect, as directed by engineer in charge pwd-2018 ps no-174c 75 supply and wiring of submains with 2 nos. of 2.5 sq. mm. frlsh pvc insulated1100 vgrade multistrand singlecore copper conductorcable in 25mm dia heavy duty (2mm thick) pvc conduitwith2 nos 2.5 sq.mm.frlsh pvc insulated multistrand copperconductor cable asearth continuity wire drawn in conduit complete in all respect, as directed by engineer in charge pwd-2018 ps no-261c 76 supply and fixing of power plug with 20 amp./250 voltflush type modularswitchand 5 pin 20 a/250 voltflush typeuniversal modular socket switch on concealed m.sboxincluding supply of allmaterial, labourt&petc. complete in all respect, as directed by engineer in charge .pwd-2018 ps no-1139a 77 s&f surface/flush mounting 8 ways spn distribution board with additional metal door without mcb complete in all respect, as directed by engineer in charge. pwd-2018 ps -1024a 78 s&f of 6 amp to 32 amp. mcb (10 ka) c curve complete in all respect, as directed by engineer in charge.pwd-2018ps -1002cat-a 79 s&f of 40amp. dp mcb (10 ka) c curve complete in all respect, as directed by engineer in charge. pwd-2018 ps no-1010 cat-a 80 providing and fixing circular/ hexagonal cast iron or m.s. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ m.s. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. (dar/10.18/based on uppwd/sor-2020))

State Government

TRN :49005623 | 26 May, 2025

Tender Value : 18.56 Crore

Jayal - Rajasthan

Tender for tender for widening and strengthening on kasnau (sh-92a) to dehri - tarnau - merwas - upto mataji road - 1 part a road work clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per morth specification clause 201. by mechanical means in area of non-thorny jungle 2 excavation in soilwithdozer with lead upto 100 mexcavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. 3 construction of embankment with material obtained from roadway cuttingconstruction of embankment with approved materials deposited at site obtained from roadway cutting and excavation from drain and foundation or other structures graded and compacted to meet requirement of tables 300-1 and 300-2 as per morth specification clause 305.3 4 construction of embankment with material obtained from borrow pitsconstruction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300-1 and 300-2 with a lead upto 50 m as per morth specification clause 305.3 5 granular sub-base with well graded material (table 400-1)by mix in place methodconstruction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavatorat omc, and compacting with smoothwheelroller to achieve thedesired density, complete as per morth specification clause 401. for grading iiimaterial 6 crusher run macadam baseproviding crushed run stone aggregate greading conforming to table 400-14 depositing on a prepared surface by hauling vehicles, spreading and mixing witha motor grader, watering and compacting with a threewheel 80-100 kn static roller as per morth specification clause 407 to form a layer of sub-base/base by mixing plant method with 53 mm maximum size of aggregates 7 wet mix macadamproviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing thematerial with water at omc in mechanical mixer (pug mill), carriage of mixed material by tipper to site, layingin uniform layers in sub-base/base course on a well prepared sub-base and compacting with smoothwheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per tables 400-12 & 400-13 and morth specification clause 406. by mechanical means with all lead 8 prime coatproviding and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base(wbm/wmm) including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per morth specification clause 502 9 tack coatproviding and applying tack coat with bitumen emulsion (rs-1)using emulsiondistributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per morth specification clause 503. 10 tack coatproviding and applying tack coat with bitumen emulsion (rs-1)using emulsion distributor at the rate of 0.20 to 0.30 kg per sqm on the prepared bituminous surface cleaned with hydraulic broom as per morth specification clause 503. 11 providing and laying dense graded bituminous macadam with 100-120 tph batch type hmp producing an average output of 75 tones per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5 percentby weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specifications clause 505 complete in all respects. bitumen (vg-30)grading - ii (26.50 mm (nominal size)) 12 providing and laying bituminous concrete with 100-120 tph batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6per centof mix and filler,transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specifications clause 507 complete in all respectsfor grading-ii(13 mm nominal size) bitumen (vg-30) 13 providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per morth specification clause 510.by mechanical means bitumen (vg-30) 14 providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per morth specification clause 511type b bitumen (vg-30) 15 part b c.c. pavement work dry lean cement concreteconstruction of dry lean cement concrete sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. 16 construction ofun-reinforced , plain cement concrete pavement m-40 (grade), thickness as per design, over a prepared sub base, with 43/53 grade cementas per clause 602.2.2 , coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a in fullyautomatic batching plant andtransported to site intransit mixer for having continous agitated mixer, manufactured as per approved mix designincluding pumping of r.m.c. from transit mixer to site of laying , with all lead and lift including cost of admixtures in recommended portion as per is 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using fixed form paver and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using water finishing to lines and grade as per drawingand morth specification clause 602 including vaccum dewatering process with all required equipments (dowel bars will be paid seprately). 17 providing and fixing of dowel bars of mild steel confirming to is : 432 of specified length and diameters as per morth specification irc 15 & 58 including cutting, placing in position across transverse joint with proper spacing, providing with pvc sleeve complete as per drawing, technical specification and as per direction of the engineer-in-charge. 18 part c protection wallearthwork in excavation for structures as per drawing and morth specifications clause 304.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. ordinary soil upto 3 m depth 19 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 20 stone masonry work in cement mortar in foundation complete as per drawing and morth specifications clauses 1402, 1405, 2102 & 2104. random rubble masonry in 1:6 cement mortar 21 plastering with cement mortar (1:4), 20 mm thick on stone work. 22 providing pcc m-20 architectural coping on the top of wing wall, return wall etc. complete as per drawing and morth specification clauses 1313, 1411 and 2206.650 mm thick 23 part d c.d.workearthwork in excavation for structures as per drawing and morth specifications clause 304.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. ordinary soil upto 3 m depth 24 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 25 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c. grade m 20nominal mix (1:2:4) 26 providing and fixing stone slab covering over drains (kota/bijoliya quarry) having thickness 75 mm to 150 mm including filling of joints in cement mortar 1:3 with 50 mm thick cement concrete flooring in 1:2:4 mix complete with good finish as per approved drawings and specifications.for drain opeining size 300 to 450 mm stone patty drain cover size 800mm x 600mm x 75mm 27 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 28 providing and laying reinforced cement concrete pipe np3 as per design in single row providing and laying reinforced cement concrete pipe np3 for culverts on first class bedding of granularmaterial in single row includingfixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 2905. 29 600 mmdia 30 300 mm dia 31 part f road saftykilometrestonereinforced cement concrete m15grade kilometre stone/local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and morth specification clause 801 32 5th kilometre stone (precast) 33 ordinary kilometer stone (precast) 34 200 m stone (precast) 35 traffic signsretro-reflectorised traffic signsproviding and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 801.3.1, fixed over aluminium sheeting, 1.5 mm thick supported on gi pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and morth specification clause 801 36 600 mm equilateral triangle 37 600 mm circular 38 600 mm x 450 mm rectangular 39 900 mm side octagon 40 direction and place identification signs upto 0.9 sqm size boardretro-reflectorised traffic signsproviding and erecting direction and place identification retro-reflectorised sign asper irc:67 made of encapsulated lens type reflective sheeting vide clause 801.3.1. fixed over aluminium sheeting, 2 mm thickwith areanot exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and morth specification clause 801. direction and place identification signs upto 0.9 sqm size board 41 direction and place identification signs with size more than 0.9 sqm size boardretro-reflectorised traffic signsproviding and erecting direction and place identification retro-reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 801.3.1, fixed over aluminium sheeting, 2 mm thickwith areaexceeding 0.9 sqm supported on dia gi pipe firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and morth specification clause 801 42 marking centre line and stop lines etc. on road as per irc pattern with thermoplastic paint of approved quality and make with 8% glass beads laid on the road surface at temperature 160 c with a special applicator machine complete with a special applicator machine complete with labour material and traffic diversion arrangements. 43 supplying and fixing of cat’s eye made of aluminium alloy size 75x100x22 mm having 21 biconvex lenses embedded in circular disk of abs plastic on each side. 44 providing and fixing mukhya mantri sadak yojana/ mahatma gandhi rajya sadak yojana informatory sign board with logo for roads funded by state road fund having m.s. definition plate of 1.60 mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. the logo shall be made out of 1.6mm thick circular plate duly framed with ms angle 25x25x5 mm on back and fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. the size of definition plate shall be 1500x600mm and embedding the posts by m-15 cement concrete block45 cm x 45 cm x 60 cm, 60 cm below ground levelincluding lettering / writing and painting etc. complete in all respect.as per morth specification clause 801. 45 supply of swiss type of hazard marker, made out of 2 mm thick m.s. sheet size of box is 15x15 cm with hold fast at bottom, the body is painted in orange stoving enamel paint with white/high intensity grade micro-prismatic type sheeting, on all four side.

State Government

TRN :48961517 | 21 May, 2025

Tender Value : 4.69 Crore

Jayal - Rajasthan

Tender for construction of sankhwas bypass--1 part a road work boundary pillar reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and morth specification clause 807 2 clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per morth specification clause 201. by mechanical means in area of non-thorny jungle 3 excavation in soilwithdozer with lead upto 100 mexcavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. 4 construction of embankment with material obtained from borrow pitsconstruction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300-1 and 300-2 with a lead upto 50 m as per morth specification clause 305.3 5 carriage of material from quarry / crusher to work site including loading, unloading and stacking all complete. 6 crusher run macadam baseproviding crushed run stone aggregate greading conforming to table 400-14 depositing on a prepared surface by hauling vehicles, spreading and mixing witha motor grader, watering and compacting with a threewheel 80-100 kn static roller as per morth specification clause 407 to form a layer of sub-base/base(b) by mixing plant method(i) with 53 mm maximum size of aggregates 7 granular sub-base with well graded material (table 400-1) by mix in place method construction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavatorat omc, and compacting with smoothwheelroller to achieve thedesired density, complete as per morth specification clause 401.for grading iiimaterial 8 wet mix macadamproviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing thematerial with water at omc in mechanical mixer (pug mill), carriage of mixed material by tipper to site, layingin uniform layers in sub-base/base course on a well prepared sub-base and compacting with smoothwheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per tables 400-12 & 400-13 and morth specification clause 406. by mechanical means with all lead 9 prime coatproviding and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base(wbm/wmm) including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per morth specification clause 502 10 tack coatproviding and applying tack coat with bitumen emulsion (rs-1)using emulsiondistributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per morth specification clause 503. 11 providing and laying dense graded bituminous macadam with 100-120 tph batch type hmp producing an average output of 75 tones per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5 percentby weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specifications clause 505 complete in all respects. bitumen (vg-30) grading - ii (26.50 mm (nominal size)) 12 providing and laying bituminous concrete with 100-120 tph batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6per centof mix and filler,transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specifications clause 507 complete in all respects for grading-ii(13 mm nominal size) bitumen (vg-30) 13 part b protectionearthwork in excavation for structures as per drawing and morth specifications clause 304.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. ordinary soil upto 3 m depth 14 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 15 stone masonry work in cement mortar in foundation complete as per drawing and morth specifications clauses 1402, 1405, 2102 & 2104. random rubble masonry in 1:6 cement mortar 16 providing pcc m-20 architectural coping on the top of wing wall, return wall etc. complete as per drawing and morth specification clauses 1313, 1411 and 2206.650 mm thick 17 plastering with cement mortar (1:4), 20 mm thick on stone work. 18 providing and laying reinforced cement concrete pipe np3 as per design in single row providing and laying reinforced cement concrete pipe np3 for culverts on first class bedding of granularmaterial in single row includingfixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 2905. 19 600 mmdia 20 300 mm dia 21 providing and laying precast reinforced cement concrete box culvert section of m-40 grade designed for aa class loading as per irc specifications including to effect of impact, eq etc. complete on firm base of 200mm thick lean concrete of m-10 grade with aggregate of size 40mm nominal of following internal size the work includes required safety measures cost of design of rcc precast box and its proof checking from iit / nit / government engineer college complete in all respect as per specifications size 1.00 m x 1.00 m 22 part c road furniturekilometrestonereinforced cement concrete m15grade kilometre stone/local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and morth specification clause 801 23 5th kilometre stone (precast) 24 ordinary kilometer stone (precast)

Central Government/Public Sector

TRN :34439631 | 16 May, 2025

Tender Value : 0

Nasikcity - Maharashtra

Tender for gem bids for 6 pcs mini pliers set , 3 pcs pliers set , rubber hammer , rubber plastic hammer , combination spanner set , 14 pcs screwdriver set , mini hacksaw , 9 pcs hex key , 6 inch adj wrench , 8 inch adj wrench , 6 pcs needle file set , electricians scissors , 115 pcs tools set drill , 12 pcs 1 4 inch socket set , flexible screwdriver set 12 pcs , hacksaw frame big , 4v cordless screwdriver , snap off and cutter blade , tool box plastic 16 inch , tool box metal 18 inch , wire stripper , 55 pcs screwdriver bits set , tweezer set 10 pcs anti static , 9 pcs hex key set , cordless blower 20v , cordless vacuum cleaner 20v , cordless mini cut-off tool 20v , grinder cordless , laminate router trimmer 500w , finishing sander , air compressor 24 lit , air spray gun , 5 pcs extractor set , high pressure washer 1200w , soldering station 60w , digital multimeter , lithium ion battery pack 2.0 ah 20 volt , lithium ion battery pack 4.0 ah 20 volt , mini grinder , jig saw , jig saw blade set , 7 pcs pliers set , thermocol foam cutting machine , f clamps 50x 250mm , f clamps 50x150mm , cg clamps 6 inch , cg clamps 4 inch , grinding wheel 4 inch set of 10

Central Government/Public Sector

TRN :34430866 | 15 May, 2025

Tender Value : 0

Jammu - Jammu And Kashmir

Tender for gem bids for cover assy , driven plate for clutch , tie rod end , oil filter , primary chain set , door handle outer rh , door trim pad , shaft drive , fork ms , sleeve for wire 6mm od , gear spur internal 33teeth , main bearing set , gear shift , assy ball joint lh , hose tmo 2 , rear hub bearing

Central Government/Public Sector

TRN :34428022 | 16 May, 2025

Tender Value : 0

North 24 Paragana - West Bengal

Tender for gem bids for purchase of spares lock washer,dowel pin(sl-313),washer,cotter pin,washer,screw,clip(price list sl-510),bracket,washer(price list sl-239),washer,ball socket/cap,o ring,spring,spring,spring(obm 30 hp mariner page no 39 sl no 47),washer (obm 30 hp mariner prop shaft),cap,spring,gasket,coller,roll pin,spacer(page-03),check valve,bushing,gasket,seal,o ring,fitting,spring,shim set(0.1,0.15,0.3,0.5),oil seal,nut,bushing,oil seal-upper,upper thrust plate,shift rod joint(include with complete housing),spacer,clamp,oil seal -lower,bolt,washer,o ring,gasket,link rod,bushing(page-07),wave washer,holder(price list sl-54),friction plate,bushing,water plug,oil seal,washer,insert,set plate,lock plate,impeller,float needle,throttle shaft,hose rubber arrow (p--20),reverse lock rod,lanyard switch,trim tab,gear shift,bushing,diaphragm,thrust hub,ball bearing,labyrinth seal,cam rod (long),fuel connector engine end,actuator arm(page-11),flushing plug,lever assy,water pump housing - upper,valve bleed,water pump repair kit,lower mount(p-31),needle bearing,rod,guage and cap assy (mariner plate fuel tank),tilt tube,hand lever,shift lever (black),upper end cap,reed block assembly,exhaust cover,buttom yoke(black),crankshaft,coil plate assembly,bottom cowl (black),driveshaft (long)(sl-484),remote control,drive shaft housing (short-black),starter motor,gear housing (basic- black)

Central Government/Public Sector

TRN :34428901 | 15 May, 2025

Tender Value : 0

North 24 Paragana - West Bengal

Tender for gem bids for purchase of spares damper lower(115 hp p-9),screw, end cap mounting,lock washer, wiring harness clamp screw,nut, rotor shaft to distributor housing (ms sl no-,strap(115 hp p-11),clip(115 hp p-15),washer((115 hp p-37),boot, high tension cable to coil,clip(115 hp p-15),plug,spark(ngk lkr6e) (p-8),washer(115 hp p-7),bush(115 hp p-37),o ring adaptor stem (ms sl no-158),bush shift lever(115 hp p-37),fetting(115 hp p-28),clip(115 hp p-13),washer(115 hp p-10,washer(115 hp p-3),nut(115 hp p-29),bolt 6 x 12 mm (p-7),element assy, oil cleaner (p-4),boot, high tension cable (ms sl no-47),nut, throttle control lever screw (ms sl no-77),bolt 16x50 mm(115 hp p-10),element,filter,hose(115 hp p-15),hook engine cover rr stbd ((p-7),grommet, high tension cable to coil (ms sl no-46),hook engine cover rr port(p-7),housing tiller handle,brush and spring assy (ms sl no-49),gasket, distributor cap,diaphragm assy (ms cat sl-140),spring (ms sl no- 96),cushion(p-12),clamp, fuel line attaching (ms sl no-147),hose(115 hp p-15),adjuster throttle(p-37),hose(115 hp p-28),gasket, transfer port cover (ms sl no-186),fitting, fuel outlet (ms sl no-144),hose , economizer (ms sl no-128),bearing set connecting rod(p-19),check valve assy (ms cat sl-139),cover water pressure valve(p-15),grip, handle(p-37),switch assy emergency,stop, rubber starter motor (ms sl no-100),fuel line adaptor to fuel pump 05 (ms cat sl-148),lever shaft(115 hp p-37),buzzer(p-37),water pump housing(115 hp p-27),lever hook rr port(115 hp p-7),lever hook rr stbd (p-7),switch assy trim (115 hp p-37),injector (p-13),gasket engine holder(p-21),ignition coil assy (p-26),rotor distributor (ms cat sl-42),bkt tilter handle(p-35),bracket,swivel(p-39),propeller (3x13x17-kl)(p-59),separator assy(p-13)

Related Sub Industries : Machine Tools

List of tool Tenders

Get Tool Tender Alert...

Related Sub Industries : Machine Tools

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us