Bidding Support

414055

Bidding Support

Warm Greetings from www.thetenders.com, the fastest growing tender information portal in India.

To Carryout Complete Farication, Supply And Installation Of Dismantling Type Hand Rails And Toe Plates, Phase#2 Rp Discharge Line Tr Enches Of Desalination Units. Idder Shall E Ensure Supplied Materials Should E Suitale For Present Harsh Sea Water Environmental Con Dition. Scope Of Work To Carryout Complete Farication, Supply And Installation Of Dismantling Type Hand Rails And Toe Plates, Phase# 2 Rp Discharge Line Trenches Of Desalination Units, Actual Volume Of The Work Shall E Checked And Confirmed Y The Idder After Site S Urvey. Further To The Survey The Idder Shall Provide Detailed Procedures With Activity Reakdown Including Method Statement And Risk Assessment For The Scope Of Work.# Site Visit Can E Made Any Working Day From Sunday To Thursday, Etween 07:30 And 14:30Hours With Prior Appointment From Concerned Department Manager Of Dewa. Contact Engineers Details. Mohammad Rafi 0529740743/048044505 Zaid Hussain: 0505805854/048044505 A.#Surface To E Coated Shall E Thoroughly Washed Using Clean W Ater To Remove All Adherent Salts, Chemical Fumes, Dust, Etc. Prior To Last Cleaning. # .#Moisture And Oil Separators Shall E Used Y The Contractor For Lasting Should E Checked Every 6 Hourly And As And When Needed For Contamination. Contaminated Filters/Separator S Should E Changed Immediately. C.#Surface Should E Free From Sharp Edges, Chemicals, Dust, Solule Salts, Grease & Oil Or Any Other Contamination Prior To Coating. D.#Prepared Surface Shall Meet The Requirements Of Sa 2.5 As Per Iso 8501E.#Any Surface Adjoini Ng The Existing Coating, The Coated Surface Shall E Roughened To Aout 25 Mm For Etter Adhesion Of Newly Applied Coatings To Existing Coating. F.#Last Cleaned Surface Shall E Coated With One Complete Application Of Primer As Soon As Practicale Or Efore Any Discolo Ration Occurs On The Surface.# G.#Any Crevices, Minor Scratches Shall E Filled With Coating Manufacturer Recommended Fillers Prior To Applying The Coatings. H.#Coating Application Shall E Y Airless Spray Only I.#Applied Coat Shall Have Minimum Dry Film Thicknes S On Each Coat. During Coating Application Wet Film Thickness, If Applicale, Shall E Measured To Confirm Desired Dft Will E Achieved . # J.#Where Coating Is To E Applied Y Rush Or Roller Contractor To Ensure Smoothfinal Appearance With Negligile Rush Marks Left I N The Applied Coating.# K.#Any Spots Or Repairs In Application Shall E Completely Coated Efore The Next Coat Is Applied, Within Recoat Interval Time.# L.#Corners And Edges Of The Surface Shall E Rounded To A Radius Of 25Mm Y Grinding Prior To Application Of Coa Tings. M.#Topcoat Color Should E As Per The Existing Color Code Only And Any Changes Will E Notified To The Contractor. N.#Repairi Ng And Remedial Works On Identified Defects Shall E According To The Touch Up And Repair Recommendations Of Coating Manufacturer Onl Y. # O.#Environment Condition Shall E Checked And Recorded Efore Starting Of Work And Every 2 Hourly On Same Day Till The Completio N Of Work. General Conditions Forenvironment Condition Shall E As Elow:-# I.#Surface Temperature Shall E Etween 10Oc And 40Oc Ii.# Relative Humidity Shall E Less Than 85%. Iii.#Surface Temperature Shall E More Than 3Oc With Respect To The Dew Point Temperature. I V.#There Shall Not E Rain Or Strong Wind That Can Affect Cleanliness Of The Surfaces. Specification Material Hand Rails With Toe Plate Ms Pipe & Ms Plate Post: Schedule 40 Ø19 To 50Mm # @Interval Of Minimum 1Mtr Top And Ottom Rail: Schedule 40 Ø19 To 50Mm # Distance Etween Top And Ottom Rail # Minimum 400Mm. Ase Plate: 10 Mm Thick Plate With Holes Toe Plate: Mild Steel, Size 4 To 10Mm Thick 75 To 150Mm Width. Fixings: M12 X 50Mm 4 No#S Per Post Coating System Specification. Surface Preparation: Hydro Last Cleaning, Manual And Mechanical Cleaning. Primer Coat: Surface Tolerant Epoxy Coating. Dft # 150 Microns Mid Coat#: Polyamide Cured Epox Y Coatings. Dft # 125 Microns Top Coat#: Polyurethane Coatings. Dft # 50 Microns Color Code For Handrails: Traffic Yellow # Ral 1023 # 325 Microns. Paint Manufacturer: Only Gloally Renowned Coatings Shall E Used S Uch As Hepmel, Jotun, Sigma, Akzanoel, Etc.

GTN :14107210
Dubai - Dubai

GLOBAL Hire Our Expertise :

  • Tender Bidding
  • Tender Consultancy
  • Tender Advisory
  • Identify Eligibility Criteria
  • Identify Penelty Clauses
  • Highlight Important Dates
  • Technical Bid Preparation
  • Offline Bid Preparation
  • Online Bid Preparation
  • Offline Bid Submission
  • Online Bid Submission
  • Track Corrigendum / Addendums
  • Attend Pre Bid Meetings
  • Consistent Liaison & Coordination
  • EMD Follow Ups

GLOBAL - bidding
image

We heartily welcome your move to excel your business to new heights.

Set Tender Alert

Activate daily alerts to know the tenders available of your work.

Get alerts

Bidding Support

Ask experts, how to fill bid forms, submit bids, participate in bids.

Get in touch

GeM Registration

Looking for GeM Registration? Get in touch with us and we will do the needful.

Registration

Digital Certificate

Get DSC for e-Tendering, e-Auction, e-bidding, Corporations / Associations / Others Tenders

Purchase now

Tender Awards

Want to know who's got the tender and are looking for subcontracting?

Connect now

Projects

Government and other private players, Real-time Updates of Project Information

Get info

International Tenders

We almost cover all the regions and countries across the world. Click to take your business to new heights.

Start now

Web Design

Get the Best Offers & Deals, expertise in developing static websites, dynamic websites and e-commerce.

Design now

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us

W B


Copyright ©2018 - Thetenders.com. Read Policies