Bidding Support

007721

Bidding Support

Warm Greetings from www.thetenders.com, the fastest growing tender information portal in India.

Supplying, Installation, Testing And Commissioning Of The Passanger Cum Bed Elevator Having Following Main Features: 20 Passengers Cum Bed, Stops, Mr Rated Speed Adjustable Up To /Sec With Dlp, As Per Rajasthan Pwd Specification For Electrical Work 2012 & Is 14665 Part I To V With Relevant Rules For Lifts Having Following Main Features Amotor: Gearless Lift Drive Comprising Of High Starting Torque Lift Duty, 3 Phase 440 Volts A.C. Permanent Magnetic Synchronous Motor Of Proper Rating With High Effciency Shall Be Used. Warrenty/Gaurenty From Motor Oem For Minimum 5 Years. B Opration / Drive : Mocrocessor Based/ Plc, Ac Variable Voltage Variable Frequency Variable Speed V3f Vector Control Drive With Encoder Feedback Closed Loop System Shall Be Used For Lift Car And Door Operation Which Shall Be Full Collective Selective Opreration Hall Call Demand Response, Up/Down Hall Stop, Main Up/Down Contactor With Overload And Phase Reversal Relay And Safety Control. Warrenty/Gaurenty From Motor Oem For Minimum 5 Years. C Traction Medial Main Hoist Flat Coated Steel Belt/ Rope. Thimbles Of Spring Permit Adjusment Of Uniform Tensionfor Smooth Opration Of The Elevator Pulse Belt Montoring System To Avoid The Cut In The Belt. D Car : Car Should Be With Ms Platform With Bracings Of Adquated Size And To Sustain The Impact Load Cabin Pluse Passangenrs With Safety Factor Of Fire For Steel With Anti Skid Pvc Flooring And Side Panels Should Be To Stainless Steel With Hair Line Finish Of Sheet Of Grade 304 Duty With S.S. Handreails . Car Celling Shall Be Steel Finish With Aesthetic Appearances With Led Celling Light . The Size Of The Car Shall Be Taken As Per Available Lift Well Size And Relevant Bis Code Of Lifts. Car Panel Will Also Be Of Ss 304 Grade Finished With Emergency Stop Device, Emergency Alarm, Mechanical Door Safety Device, Full Length Infra-Red Curtain In Car Door . Facility Of Auto /Attended Mode . All Car Panel Buttons And All Floor Switches Must Be With Brail Language As Per Lift Act. Agency Shall Also Provide & Install One No.2 Mp. Ir, Ip Based Ceiling Mounted Dome Camerain The Car Complete With Connection Cable & Accessories To Be Cinnected With Existing Cctv System In The Building . The Inspection Unit Shall Be Provided At The Top Of The Car. E Landing Doors : All Landing Door Shall Be Fully Automatic Centre Opening /Telescopic Made Of Hair Line Finish Stanless Steel Grade 304 With Key Holes And Infrared Curtainds With Unloking Facility From Outside. F Emergency Light : Appropriate Rechargable Battery Oprarated Led Emergency Light In The Car And Along With Alarm Switch Shall Be Provided. G Ard : Automatic Rescue Device Ard Shall Be Provided According To Passenger Capacity With Smf Batteries Of Good Quality After Pre Approval Of Engineer In Charge. H Audio - Visual Indication : Audio Visual Indication In Lift Car . Showing Over Loading Such That Doors Kept Open Till Excess Load Is Removed. I Scrolling Indicators : Digital Scrolling Indicator System For Up-Down Arrow With Floor Position Indicator Shall Be Provided Inside The Car And At All Stops /Floors. J Buffers: Spring Buffers /Pu Buffers Shall Be Provided. K Car Fan : Energy Efficient Car Fanlblower With Automatic Sleep Timer Shall Be Provided. L Voice Annunciator : Voice Annunciator With Suitable Music Shall Be Provided In Lift Car. M Self Diagnostics System For Operational And Safety Parmeters Shall Be Provided In Control Panel N Mechanical / Electronic Over Speed Governor, Door Key Holes In The Floor Doors, Firman Switch Shall Be Provided. O Lift Machine Hoisting Arrangment In The Lift Machine Room, Counter To Balance Promote Smooth And Aconomic Operation With Steel Guide Rails For The Car & Counter Weight, Trap Door, Lifting Hooks As Required And Monkey Ladders For Lift Pit Should Be Provided By The Agency Along With All Other Steet Structure Works, Foundations For The Machine Etc As Per Required. P Warrenty/Gaurenty Period From Lift Oem For Complete Item Must Be Submitted In Technical Bid By The Bidder.Appropriate Test Certificate Test At Site, Test At Manufactures Work Place & Performance Test From Oem Shall Be Submitted By The Bidder After Successfull Installation.Lift Make And Model Shall Be Approved By Engineer In Charge Before Execution As Per Specification, Terms & Conditions And Eligibility Criteria. Wiring Of Light Point/ Fan Point/ Exhaust Fan Point/ Call Bell Point As Per Pwd Specification For Electrical Works With Isi Marked 1.5 Sq. Mm Nominal Size Fr Pvc Insulated Unsheathed Flexible Copper Conductor 1.1 Kv Grade Is:694 And 1.5 Sq. Mm Nominal Size Fr Pvc Insulated Unsheathed Flexible Copper Earth Conductor 1.1 Kv Grade Is:694 In Recessed Isi Marked Mms Is:9537 P - Iii Vergin Material Pvc Conduit & Its All Accessories J.B., Bends Etc., Round Tiles, 18 Swg G.I. Box With Earth Terminal, 6 A Switch, 3 Pin Ceiling Rose/ Lamp Holder / 3 Point Connector, 3.0 Mm Thick Isi Marked Phenolic Laminated Sheet Is : 2036 - 1995, Al. Alloy/ Cadmium Plated Iron Screws 20 Mm Cup Washers Etc. All As Per Pre Approved By Engineer In Charge, Making Connections, Testing Etc. Complete As Required. For Specification Of Copper Conductor, Phenolic Laminated Sheets & Electrical/ Wiring Accessories Refer Chapter E - 04, E - 05 & E - 07 . For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Short Point Up To 3 Mtr. Wiring Of 3/5 Pin 6 Amp. Light Plug Point As Per Pwd Specification For Electrical Works With Isi Marked 1.5 Sq. Mm Nominal Size Fr Pvc Insulated Unsheathed Flexible Copper Conductor 1.1 Kv Grade Is:694 And 1.5 Sq. Mm Nominal Size Fr Pvc Insulated Unsheathed Flexible Copper Earth Conductor 1.1 Kv Grade Is:694 In Recessed Isi Marked Mms Is:9537 P - Iii Vergin Material Pvc Conduit & Its All Accessories J.B., Bends Etc., Round Tiles, 18 Swg G.I. Box With Earth Terminal Of Required Size, 6 A Switch, 3/5 Pin 6 A Socket, 3.0 Mm Thick Isi Marked Phenolic Laminated Sheet Is : 2036 - 1995, Al. Alloy/ Cadmium Plated Iron Screws 20 Mm Cup Washers Etc. All As Per Pre Approved By Engineer In Charge, Making Connections, Testing Etc. Complete As Required. For Specification Of Copper Conductor, Phenolic Laminated Sheets & Electrical/ Wiring Accessories Refer Chapter E - 04, E - 05 & E - 07. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . On Board Providing & Fixing Of Ik09 Recessed/Surface Mounting Heavy Duty Horizontal Type Sheet Steel Of 1.6 Mm Thick Distribution Board As Per Pwd Specification For Electrical Works Isi Marked Conforming To Is-13032 & Is-8623 / Conforming To Iec 61439-3. Phosphatised/ Powder Painted Complete With Suitable Rating Insulated Copper Bus Bar, Shorting Link, Neutral Link, Earth Link, Connecting Wire Of Suitable Rating And Din Bar, Masking Sheet, Including Making Internal Db Terminations With Copper Lugs And With Detachable Gland Plate, Including Making Connections, Testing Etc. As Required.Oem Shall Have Submit Nabl / Cpri / Erda Accrediated Lab Test Reports Before Execution & All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Ip-43 Double Door Three Phase 4 Way 12 O/G + 8 I/C Providing & Fixing Of 240/415 V Ac Mcb With Positive Isolation Of Breaking Capacity Not Less Than 10 Ka B/ C Tripping Characteristic As Per Type Of Load And Site Requirement 4Kv Impulse Withstand Voltage, As Per Pwd Specification For Electrical Works With Isi Marked Is 88281996 / Conforming To Iec 60898-1 2002, Iec 60947-2, Low Watt Losses, Trip Free Mechanisum, Energy Limiting Of Class 3 As Per Iec, Minimum Phase Termination Capacity Of 35Sq.Mm., Conductorline Load Reversibility, Label Holding Facility, Ip 20 Contact Protection And Fitted With Existing Distribution Board/Sheets, Min. Operation 20, 000 Upto 32 A Rating And 10, 000 Upto 63 A, 5000 For 80 A Rating Including Making Connections, Testing Etc. As Required. . Oem Shall Have Submit Nabl / Cpri / Erda Accrediated Lab Test Reports Before Execution & All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Single Pole Mcb 6 A To 32 A Rating Four Pole Mcb 50-63 A Rating Providing & Fixing Of 240/415 V Residual Current Circuit Breaker Rccb As Per Pwd Specification For Electrical Works With Isi Marked Is:12640-1 / Conforming To Iec 61008 -1, Rated Conditional S/C Current Of 10 Ka, Truly Current Operated And Shall Operate On Cbct Mechanisum, Provision For Pad Lock, Min. Operation 10, 000 Upto 63 A Rating And 5000 For 100 A Rating, Minimum Phase Termination Capacity Of 50 Sq.Mm. Rigid Wire, Ip 20 Contact Protection With Existing Distribution Board / Sheet Including Making Connections, Testing Etc. As Required.Oem Shall Have Submit Nabl / Cpri / Erda Accrediated Lab Test Reports Before Execution & All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Four Pole 100/300 Ma Sensitivity 40 A Rating Sitc Of Chemical Gel Earthing System Of Dual Pipe Technology Made Of With B Class G I Pipe As Per Is 1239 Part-1:2004 Of Medium Duty Of Following Sizes As Per Points Mentioned A, B, C, D, E Below :- A Filled With Anti Corrosive Conductive Compounds With The Permanent Sealings At Both The Ends, Cpri/ Erda Tested With Rms Capacity Of Minimum 35- 40 Ka For Withstanding 1 Second . B To Ensure The Moisture Content And Electrical Conductivity, 25 Kg For 2000 Mm & 50 Kgs For 3000Mm Of Resistance Lowering Earth Enhancement Material Shall Be Used As A Backfill Compound. The Compound Shall Be Tested Form Nabl Acredeated Lab For Low Resistivity Less Than 0.12 Ohm - Meter & High Conductivity In Nature With Carbon As A Major Content As Per Referance Of Is 3043-1987, Ieee 80-2013 Clause 14.5D, Ieee 837 & Ier 1956 With Latest Amendemnts ©Heavy Duty Weather Proof Poly-Propylene Earth Pit Chamber With Lockable Jam Free Lid Suitable For Safe Working Load 5000 Kg Or More Of Size Top Dia. 225 To 260 Mm, Bottom Dia 300 To 350 Mm. And Height 250 To 300 Mm. D Testing Of Earth Resistance For Value Of 5 Ohms Or Less As Required & Must Record By Engineer In Charge During Site Visit And Ensure To Enter In Measurment Book. E Self Certificate For Confirming Above Standards From Oem Is Mandatory. All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . With Pipe In Pipe Technology Outer Pipe Dia. / Inner Pipe Dia. Minimum 100 Mm Dia Borewell Gi Pipe 3000 Mm Long, 80 / 50 Mm, Terminal 50 Mm X 6 Mm Gi Strip Supply & Laying Following Size Earth Wire In Horizontal Or Vertical Run In Ground/Surface/Recess Including Riveting, Soldering, Saddles, Making Connection With Gi/Cu Thimble Etc. As Required. All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . 8 Swg Copper Wire Providing & Fixing Of Ip40 Led Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back Lit Smd Mid Power Led Downlight With Die-Cast Aluminum Housing & Heat Sink For Heat Dissipation With Uv Stabilized Non Yellowish Diffuser With Internal/ External Bis Complience 2.5 Kv Surge Protected Isolated Driver, With Short & Open Circuit Protection, Having Efficiency > 85% And In Compliance To Iec Standards. System Lumen Efficacy Of = 120 Lm / Watt, Thd < 10 %, P.F.=0.95, Cri >80, Life Time Of Minimum 50000 Burning Hours With, 70% Of Intial Lumen Maintaned Till Life Ends, Cct 3000°K / 4000°K / 5700°K /6000°K/6500°K As Per Ansi Bin, Maximum Power Consumption Should Not More Than The Specified Rating And Fixture Shall Be Of Bis Standard And Trade Mark Certificate T.C.. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen Printing On Housing. Oem Must Have Its Own In House Nabl Lab Setup For All Testing Facilities For Led Fixtures. Lm79/Lm80 Certificate / Report From Oem Shall Be Submitted. All As Per Pre Approved By Engineer In Charge . Foe Additional Technical Parameters Of Product/ Work, Refer Annexure A Attacheded With This Bsr. Recessed Mounting Led Downlight 6/7W Providing & Laying P.V.C. / Xlpe Insulated & P.V.C. Sheathed Un-Armoured / Armoured Aluminium Cable Of 1.1 Kv Grade As Per Pwd Specification For Electrical Works In Existing Rcc / Hume / Stoneware / Pvc Pipe/ Open Duct/Cable Trench With Filling Of Excavated Earth In Trench, On Existing Cable Trays Or On Surface Etc. Including Making Necessary Connection, Testing Etc. As Required Of Size And As Per Points A, B, C, Mentioned Below:- A Material :- H4- Grade Aluminium Conductor Of Purity >99.6 % & As Per Is:1554 P-I / Is :7098 P - I B Conductor Shall Have Electrolytic Aluminium Confirming To Is 8130, Is 3975-1999 For Armouring Of Cables In Armoured Cable Items, Is 5831 For Sheath, Is 10810 Part 0 To 64 For Testing Procedures . C Oem Must Have Iso 9001 & 14001 Certifications For Quality Assuarance & Its Own In House Nabl Lab Setup For All Testing Facilities For Cables . Appropriate Type Test Certificate / Oem Test Report Shall Be Submitted . All Above As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Armoured Cable 25.0 Sq. Mm 4 Core Providing & Fixing Of Energy Efficient Direct Fit Retrofit Polycarbonate /Extruded Al Base Housing & Diffuser Smd Mid Power Led Tube With Integral Driver, On Existing Fixture. Power Consumption Of 18W / 20W System Lumen Efficacy = 110 Lm/Watt Output, Internal Surge Protection Of 2.5 Kv, Thd < 15%, P.F.=0.95, Cri >80, Life Time Of Minimum 35000 Burning Hours With, 70% Of Intial Lumen Maintaned Till Life Ends, Cct 3000°K / 4000°K / 5700°K /6000°K/6500°K As Per Ansi Bin, Maximum Power Consumption Should Not More Than The Specified Rating And Fixture Shall Be Of Bis Standard And Trade Mark Certificate T.C.. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen Printing On Housing. Oem Must Have Its Own In House Nabl Lab Setup For All Testing Facilities For Led Fixtures. Lm79/Lm80 Certificate / Report From Oem Shall Be Submitted. All As Per Pre Approved By Engineer In Charge . Foe Additional Technical Parameters Of Product/ Work, Refer Annexure A Attacheded With This Bsr. 4, 18/ 20 Watt Led Tube Without Batten Extruded Al Base Supply & Laying Following Size Earth Strip In Horizontal Or Vertical Run In Ground/Surface/Recess Including Riveting, Soldering, Saddles, Jointing Shall Be Done By Overlapping And With 2 Set Of Brass For Cu Strip / Gi For Gi Strip Nut Bolt & Spring Washer Spaced At 50Cm Making Connection Etc. As Required. All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Copper Strip Providing And Fixing Of Iso Certified Company Made Bee Star Rated Copper Wounded Double Ball Bearing Capacitor Start, Aluminium Body Andmetallic Blade Ceiling Fan As Per Pwd Specification For Electrical Works, Conforming To Is:374-2019, & Is:1885 -P-V- 1981. With Down Rod Up To 30 Cm With Secondary Support Safety Cable, Cotter Pin With 3 X 1.5 Sq.Mm Pvc Insulated Flexible Copper Conductor Making Connection Testing Etc. As Required. Appropriate Oem Test Certificate Shall Be Submitted By Contractor. All As Per Pre Approved By Engineer In Charge. For Additional Technical Parameters Of Products/ Work, Refer Annexure A Attached With This Bsr . Sweep Bee 2 Star Rated

TRN :21897141
State Government / Civil Work
Achalpur - Maharashtra

INDIAN Hire Our Expertise :

  • Tender Bidding
  • Tender Consultancy
  • Tender Advisory
  • Identify Eligibility Criteria
  • Identify Penelty Clauses
  • Highlight Important Dates
  • Technical Bid Preparation
  • Offline Bid Preparation
  • Online Bid Preparation
  • Offline Bid Submission
  • Online Bid Submission
  • Track Corrigendum / Addendums
  • Attend Pre Bid Meetings
  • Consistent Liaison & Coordination
  • EMD Follow Ups

INDIAN - bidding
image

We heartily welcome your move to excel your business to new heights.

Set Tender Alert

Activate daily alerts to know the tenders available of your work.

Get alerts

Bidding Support

Ask experts, how to fill bid forms, submit bids, participate in bids.

Get in touch

GeM Registration

Looking for GeM Registration? Get in touch with us and we will do the needful.

Registration

Digital Certificate

Get DSC for e-Tendering, e-Auction, e-bidding, Corporations / Associations / Others Tenders

Purchase now

Tender Awards

Want to know who's got the tender and are looking for subcontracting?

Connect now

Projects

Government and other private players, Real-time Updates of Project Information

Get info

International Tenders

We almost cover all the regions and countries across the world. Click to take your business to new heights.

Start now

Web Design

Get the Best Offers & Deals, expertise in developing static websites, dynamic websites and e-commerce.

Design now

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us

W B


Copyright ©2018 - Thetenders.com. Read Policies