Filters

List of cover Tenders

List of latest cover Tenders in Indian Tenders. Click on any cover Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for cover Tenders.

All-Tenders (900)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Central Government/Public Sector

TRN :49055075 | 29 May, 2025

Tender Value : 0

Pune - Maharashtra

Tender for special repair of b veh garage of 257 fd wksp coy eme at 330 bde special repair to drain cover of strom drain line at cqa ffe aundh camp and provn of toilet block at 8 mahar under ge mh and rh khadki

Central Government/Public Sector

TRN :49055122 | 29 May, 2025

Tender Value : 40.00 Lacs

Palam - Delhi

Tender for comprehensive maintenance and certain misc b/r works in tech area at af stn palam under ge (af) palam, delhi cantt - 10; 1.00 taking down cement plaster on brick, stone or concrete surfaces of walls etc incl racking out joints hacking for key scrubbing down with water etc and removing the debris from site to out site mod land complete all as specified and directed by engr-in-charge . 2.00 m&l for 10mm thick rendering of ready mix mortar of approved make on brick work or concrete surfaces on internal walls, finished the surface even and smooth without using extra cement as on wall as whole or in patch etc complete all as specified and as directed. make- birla (hil) or its equilent. 3.00 m&l for 15mm thick rendering of ready mix mortar of approved make on brick work or concrete surfaces on external walls, finished the surface even and fair without using extra cement by using dr. fixit (wpc) @ 3% of wt of cement content complete all as specified and as directed. note:- water proofing compound shall be measured and paid seprately. 4.00 m&l for 5mm thick cement plater of ready mix mortar of approved make as on ceiling & plastering to be finished even & smooth without using extra cement complete all as specified and as directed. make- birla (hil) or its equilent. 5.00 supply only integral water proofing compound complete all as specified and as directed. 6.00 m&l for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkalic resistent primer complete all as specified and as directed 7.00 m&l for applying two coats of 100% premium acrylic emulsion paint having voc less than 50 gm/ltr and uv resistance as per is 15489-2004, alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.9 litre /10 sqm over new surfaces complete all as specified and as directed. 8.00 m&l for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkalic resistent primer complete all as specified and as directed. 9.00 m&l for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed. note:- payment for providing grooves shall be measured and paid separately. 10.00 m&l for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications complete all as specified and as directed. 11.00 demolition of cement concrete (un reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing the debris from site to out site mod land complete all as specified and as directed. 12.00 m & l for 75mm thick cement concrete (1:3:6) type c2 (using 40mm graded stone aggregate) as in plinth protection, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of pcc at every 3 metres and at every change of direction and filling the same with & including bitumen 85/25 and sand in the proportion of (1:3 ) by weight complete all as specified and as directed. 13.00 m&l for 75mm thick pcc (1:3:6) type c2 (using 40mm graded stone aggregate) as in path and paving, finished even and smooth without using extra cement complete all as specified and as directed. 14.00 m&l for 25 mm thick pcc (1:2:4) type b1 (using 20mm graded stone aggregate) as in floor, finished even and smooth with using extra cement complete all as specified and as directed. 15.00 m&l for plain cement concrete (1:3:6) type c1 (using 20 mm graded stone aggregate) as in surface channel/drain complete all as specified and as directed. 16.00 extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. 17.00 supply and fixing in repairs, sfrc drain cover any size, 75mm thick laid over existing drain complete all as specified and as directed by engr-in-charge. notes: - (i) make of sfrc manhole/drain cover and frame : (a) m/s ps concrete.(b) m/s kk manhole.(c) or equivalent as approved by ge. (ii) contractor will provide manufacturer test certificate of sfrc cover . 18.00 dismantling wall and ceiling boards ( fibre, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness, including fillets complete all as specified and as directed. 19.00 m & l for provding false ceiling of 12mm thick fine fissure board sharped finished mineral fiber accountic false ceiling tiles with back of the duly sanded and finshed with a coat of protective paint and front duly finished false system of size (600x600) mm having noise reduction co-efficient of 0.55 light reflection of 80% thermal conductivity k=0.057 w/wwc and humidity resistance of 95% fixed to true look pvc die kl -24 suspension system (hot dipped aglvanised steel section) of exposed t section consisting of perimeter wall angle of size (24x24) mm of thickness 0.45 of mm c/c universal main runner of t shape with double rotary siticing of size (38x25) mm of lenght 1200mm made from 0.33gs steel of lenght 3.60 mtr to be spced at 600x 600mm size) c/c cro runner t shape wtih double rotary siticing of size (30x24)mm of length 1200mm made 0.25 thick gs sheet spaced @ 600mm c/c (600mm 600mm) size complete all as specified and directed by engineer -in- charge. 20.00 taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and as directed. 21.00 taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 sqm but n. exc 4.0sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and as directed. 22.00 taking down shutters of any description of size n. exc 1 sqm each complete all as specified and as directed. 23.00 taking down shutters of any description of size exc 1 sqm and n exc 2 sqm each complete all as specified and as directed. 24.00 taking down shutters of any description exc 1 sqm and n exc 2 sqm each and re-fixing in the same opening after necessary repairing viz shifting of hinges/tower bolt / handle position etc complete all as specified and as directed. note:- cost of screws/nails and minor items shall be deemed to be included in the unit quoted rates. 25.00 s&f anodised aluminium powder coated frame for door, windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed 26.00 s&f anodised aluminium powder coated door shutter, aluminium section wt 0.55 kg/m including neccesary joining cleats, glazing clips, rubber neoprene packing, aluminium handle 2 nos in each door, hinges, anodised aluminium snap beading screw etc. complete all as specified and as directed. 27.00 s&f anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised, handle 2 nos in each window, aluminium fittings such as peg stays150mm long (1 no.), hinges type b-21100mm long (2 no.), suitable handle (1no.) complete all as specified and as directed. 28.00 s&f aluminium anodised with powder coating (minimum thickness of powder coating 50 micron) grill of design and parttern as approved by ge including aluminium beading complete all as specified and as directed. 29.00 s&f 5.50mm thick tinted, sheet glass of selected quality fixed to aluminium frame work complete all as specified and as directed. 30.00 m&l for 12mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & fixed with screws to timber/aluminium frame complete all as specified and as directed 31.00 s & f door closer hydraulically regulated designation no 3 universal type suitable for door shutter of 851 to 1000 mm in width of aluminum body (die cast) weight between 61 to 80 kg complete all as specified and as directed. 32.00 m&l double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete all as specified and as directed. 33.00 s & f mild steel mortic lock vertical type size 100mm 4 levers complete all as specified and as directed. 34.00 s&f aluminium tower bolt of extruded section, 150mm length of bolt and fixed with screws complete all as specified and as directed. 35.00 s&f aluminium door stopper double legged with rubber shoe 75mm long fixed to door shutters complete all as specified and as directed. 36.00 m & l 2nd class hard wood plain, solid, straight chowkhats, and frame wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed. 37.00 s&f for 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed. 38.00 s&f for factory made single extruded wpc (wood polymer composit) solid door/window and other frames/chowkhat of size 50x100 mm comprising of virgin pvc polymer of k value 58-60 (suspension grade) calcium carbonte and natural fibers (wood powder/rice husk/wheat husk) and non toxic aditives(maximum toxicity index of 12 for 100 gms) fabricated with full body threaded star headed ss screws having minimum frame density of 750 kg/cum screw withdrawl strength of 2200 n(face) & 1100n(edge) minimum compressive strength of 58 n/sqmm modules of ealsticity 900 n/sqmm and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with ms hold fast/ lugs/ss dash fasteners of required dia and length complete as per direction of enger-in-charge. make- m/s rajshree plastiwood ltd or its equivalent as per list of make. 39.00 s&f for factory made single extruded wpc (wood polymer composit) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of k value 58-60 (suspension grade) calcium carbonte and natural fibers (wood powder/rice husk/wheat husk) and non toxic aditives(maximum toxicity index of 12 for 100 gms) fabricated with full body threaded star headed ss screws having minimum frame density of 650 kg/cum screw withdrawl strength of 1800 n(face) & 900n(edge) minimum compressive strength of 50 n/sqmm modules of ealsticity 850 n/sqmm and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant. wpc to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hotmelt adhesiv on both faces of shutter and fixing with stailess steel butt hinges of required size with necessary full body threaded star headed counter sunk ss screws all as direction of enger-in-charge. make:- m/s rajshree plastiwood ltd or its equivalent as per list of makes. 40.00 dismantling of floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles and rubbish off the premises complete all as specified and as directed. 41.00 m&l for vitrified ceramic tiles 8-10 mm thick, 1st quilaty (square/rectuangular) polished, double charge shade, area of each tiles exceeding 0.36 sqm but not exc. 0.42 sqm, as in floors etc. set and jointed with neat cement slurry and pointed in white or coloured cement to match with and including over15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. 42.00 description all as per srl item no. 39.00 bove but as in skirting over 10mm thick plastering with cm (1:4) complete all as specified and as directed. 43.00 m &l for ceramic coloured/ printed non-skid tiles of size 7 to 8 mm thick( square / rectangular) area of each tile exceeding 0.06 sqm but n exc 0.16 sqm laid as in floors, set and jointed with neat cement slurry with and including over 15 mm thick screed bedding layers of cement sand mortar (1:4) and pointed with coloured cement to match with surfaces of tiles complete all as specified and as directed. 44.00 m&l for glazed ceramic coloured tiles (colour & shade as approved) of size (450x350)mm x 7mm thick as in vertical surfaces as in skirting and dado, set and jointed in neat cement slurry with amd including over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed. 45.00 s&f in repair wash hand basin, vitreous china, flat back (550x400)mm size, white including pvc waste coupling 32mm size, pvc waste pipe 32mm bore, pair of brackets of mild steel (35 x 35 x 6)mm size including one mixer cast copper alloy 15mm bore, one brass stop valve 15mm bore and one pvc connection15mm size with ptmt nuts of length 450mm long complete all as specified and as directed by engineer-in-charge. 46.00 supply & fixing in repair vitreous china ewc super constellation including flushing cistern of size (83x37x66)cm with s trap complete all as specified and as directed. 47.00 supply & fixing in repair vitreous china urinal pot white including partition, waste pipe, screw with wall fixing complete all as specified and as directed. 48.00 s&f in repairs two way wall mixer with popup waste system, hot and cold facilites and 450 mm long braidaed hoses chromium plated complete all as specified and as directed . 49.00 s&f in repair health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and as directed. 50.00 s & f in repair copper alloy cp toilet paper holder complete all as specified and as directed. 51.00 m&l for replacement of 100mm ci floor/nahani trap with grating including jointing and breaking/ dismantling any type of floor and making good cement concrete type b-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and as directed. 52.00 s&f in repair, brass chromium plated tubular towel rail, 20mm dia, d type, 60cm long between flanges complete all as specified and as directed. 53.00 taking up or down 15mm steel tubing and connections in walls, ceilins, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed. 54.00 m&l for gi tubing, 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed. 55.00 m&l for cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good cutting not exc 10 cm girth as in wall complete all as specified and as directed. 56.00 s&f in repair 15mm bore cast copper alloy, cp angle cock, screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. 57.00 s&f in repair pvc connections 15mm size with ptmt nuts of length 450mm and fixed complete all as specified and as directed. 58.00 s&f in repairs pvc connections 15mm size with ptmt nuts of length 600 mm and fixed complete all as specified and as directed. 59.00 s&f in repair cast copper alloy cp soap dish complete all as specified and directed. 60.00 s&f in repair bib taps with wall flange 15mm bore, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. 61.00 s&f in repair pillar cock, foam flow cast copper alloy, chromium plated, fancy type, 15 mm dia, capastan heads, screwed down high pressure complete all as specified and as directed. make:- cat no 8304 of make prayyag or equivalent as per list of makes. 62.00 s&f in repair plastic water closet seat cover, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. 63.00 s&f in repair pvc valveless, syphonic action type, flushing cistern low level, 10 litre capacity , white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed. 64.00 s&f in repair 610 mm long pvc waste pipe flexible type 25 mm dia suitable for couplings 32 mm / 40 mm dia complete all as specified and as directed. 65.00 s&f in repair (600 x450) mm fancy type or bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. 66.00 s&f in repairs 15 mm bore bib taps standard of ptmt any colour high pressure screwed for iron pipe and fixed complete all as specified and as directed. (minimum weight 90 gms). 67.00 s&f in repairs 15 mm two in one angle valve cast copper alloy, chromium plated with wall flange and fancy type with high pressure screwed down and with cp flange of same make complete all as specified and as directed . 68.00 m&l for 18-20mm thick granite (of jet black ) work (table rubbed and polished ) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. note:- the cost of half round moulding shall be deemed to be included in unit rate. 69.00 dismantalling water tanks and removal from site of capacity exc 250 ltr and not exc 500 ltr complete all as specified and as directed. 70.00 m &l for 500 litres capacity rotational moulded polyethene water storage tank (cylindrical vertical with closed top), white, three layers, hoisted and fixed in position complete all as specified and as directed. 71.00 supply and fixed ball brass valve high pressure with polythene float and fly nut complete to bore of pipe 20mm complete all as specified and as directed. 72.00 demolition of brick work or stone buillder built in cement mortar of any description complete all as specified and as directed. 73.00 m&l for brick work with sub class b works, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete complete all specified and as directed. 74.00 dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 75.00 s&f mild steel work such as angle iron post, flat iron in fencing including cutting as making doubble swan neck i.e. y shaped including welding with proper overlapping & welding ms plate with angle iron bottom as directed, drilling holes notching for wire etc embedded in concrete fixed vertically conforming to fe 290 grade e-165 complete all as specified and as directed. note:- embedded portion of angle iron post shall be treated with tar of coat of tar black paint and cost of the same shall be deemed to be included in unit rate. 76.00 m&l for preparation of newly steel surfaces of any description over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer of any height complete all as specified and as directed. 77.00 s&f for concertina coil with punched tape of 600 mm dia (when stretched), centre core wire of minimum 2.5 mm dia of mild steel wire conforming to is 280-2006 with galvanised coating of steel concertina coil as per requirements laid down for medium coated wire in is : 4826 hot dipped galvainsed coating of round steel wires. conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 150 rm for 10 rm of work ,minimum weight 13.5 kg for 10 rm of work including dismantling of existing concertina coil complete all as specifed and directed by engr-in-charge. (note:- the actual weight of concertina coil brought by the contractor at site shall be ascertained by boo as ordered by ge). 78.00 s&f for concertina coil with punched tape of 900 mm dia (when stretched), centre core wire of minimum 2.5 mm dia of mild steel wire conforming to is 280-2006 with galvanised coating of steel concertina coil as per requirements laid down for medium coated wire in is : 4826 hot dipped galvainsed coating of round steel wires. conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 180 rm for 10 rm of work ,minimum weight 16.5 kg for 10 rm of work including dismantling of existing concertina coil complete all as specifed and directed by engr-in-charge. (note:- the actual weight of concertina coil brought by the contractor at site shall be ascertained by boo as ordered by ge). 79.00 dismantling of fencing wire, barbed wire any type and description complete all as specified and as directed. 80.00 supply and fixing galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbed of 75mm spacing and straining and fixing to any type of standard rail, straining bolt including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured) complete all as specified and as directed. 81.00 m&l for cuting holes in brick walls exc half brick but n.exc one brick, built in cement mortar for fixing holdfasts in jambs of existing opening and making good complete all as specified and as directed. 82.00 m&l pcc (1:3:6) type c1 (using 20 mm graded stone aggregates) as in hold fast block including necessary form work complete all as specified and as directed. 83.00 s&f mild steel work framed such as grill, gratings, etc with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to fe.290.gde-e-165. complete as specified and as directed. 84.00 dismantling of fencing wire mesh, any type of any description complete as specified and as directed. 85.00 fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete as specified and as directed. 86.00 supply only chain link ms galvanised fencing, 4mm dia gi wire mesh size 100mm x 100mm complete as specified and as directed. 87.00 s&f mild steel screw bolts 12 mm dia (machine made) with hexagonal heads at one end and screwed other end to be fitted with washers (02 nos.) and one hexagonal nut, length of bolt exe 5 cm and n exe 10 cm complete as specified and as directed. 88.00 s&f mild steel fabricated round bars 10mm dia as in horizontal bars for chain link fencing incl necessary hooking at ends all as complete as specified and as directed. 89.00 excavation in post hole (or similar holes) each n.exc 0.50 cum getting out returning, filling in and ramming earth around in layers n. exc 25cm watering and removed surplus soil to a distance n. exc 50m and making good surface in soft/loose soil complete as specified and as directed. 90.00 supply and fixing in repairs, pre cast cement concrete jallies, 35 mm thick, type b0 1:2:4 (using 12.5 mm graded crushed stone aggregate) including wire fabric set and jointed in cement mortar (1:4) complete as specified and as directed. 91.00 s&f in repair aluminium composit panel (acp) sheet with 1x1.5 aluminium tube over the framed/ beam of gates. acp shall meet under mentioned technical requirements:- (i) coating on front : high quality polymer resin.(ii) core : fr core (fire retardant)(iii) thickness : 4mm(0.5 mm+3.0mm+0.5mm) (iv) weight : 7.50kg/sqm(v) width: 1200mm(vi) length: 1200 to 2400mm(vii) structure: aluminium panel are protective film,clear coating pvdf,primer coating,antirust layer,aluminium skin and polyethylene.(viii) temp resistance : between -50c to +80c(note:- the quoted rate is deemded to be included necessaryy scaffolding required and joint sealing) 92.00 s & f in repair 12mm thick toughened glass fixed with double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty and stainless steel handle purpose made on both side with locking machanism and with necessary stopper etc complete all as specified and as directed. 93.00 demolition and breaking up drain pipe 75/100mm dia ( salt glazed ware, ac or pvc) of any type complete all as specified and as directed. 94.00 s&f 75 mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete all as specified and as directed. 95.00 s&f 110 mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete all as specified and as directed. 96.00 s&f in repairs pvc(swr) bends any radius, 75 mm bore complete all as specified and as directed. 97.00 s&f in repairs pvc(swr) bends any radius, 110 mm bore complete all as specified and as directed. 98.00 hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed. 99.00 s&f sheet glass 4mm thick ordinary quality and glazing with oil putty or rubeer bedding in square n. exc 0.5 sqm in each pane complete all as specified and as directed. 100.00 s&f in repairs of sink with drainage board, made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washes and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size (915x460)mm with bowl size (410x330x160)mm complete all as specified and as directed. 101.00 s&f in repair brass chromium plated shower rose,125 mm size fixed to 15 mm bore iron pipe complete all as specified and as directed. 102.00 s&f in repair water closet vitreous china squatting pan, orissa pattern size (580x440)mm white with integral foot rests (excluding flushing cistern and flush pipe) and including with p or s trap complete including provison of lime concrete bedding fixed in repair complete all as specified and as directed. 103.00 m&l for gunniting work to rcc work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and s&f welded wire mesh fabric or wire net less than 95 x 95x 3 mm tied to existing reinforcement with nails,adhesive plaster grade for concrete and providing gunniting pressure 2.0/2.5kg/sqm with admixture 1 part of cement and 3.5 part of sand with average thickness 40 mm and making the surface even including 15mm thick plastering in cm 1:4 on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement including necessary form work to be carried out,complete all as specified.(note.- wherever reinforcement required shall be measured and paid seperately) 4. structural steel steel authority of india limited (sail) brand: sail / rashtriya ispat nigam limited (rinl) brand: rinl / tata iron & steel company (tisco, or tata steel) brand: tata / m/sjindal steels and power ltd. brand: jindal 5 factory made paneled/ glazed /gauged door shutters m/s mp wood product indore, m/s jain doors pvt ltd sonipat, goyal industiral corporation new delhi, shri krishna industries, panchkula, 6 factory made flush door shutters m/s green ply industries, m/s centuary ply, m/s dura ply. mysore chip board, archid, swastik ply wood, m/s jain doors pvt ltd 7 pvc door frame/shutters sintex, rajshri plastiwood ltd, m/s dura plast extraction pvt ltd, m/s fenesta, ecocell,accucell 8 frp door frame and shutter selected products co., sintex, rajshri plastiwood ltd, accure polytec pvt ltd ,ecocell, fiberways 9 upvc window/doors fenesta, ncl veka, madhu industries, h2o solutions, yashpoly,accucel, okotech, aseco (m/s ashish industries) 10 iron mongery mowjee, m/s kitch architectural product pvt ltd, rs industries. 11 hydraulic door closer everest, universal, godrej 12 particle board(veneered & unveneered laminated)/ block board kitply, nova pan industries, new delhi, m/s green ply industries ltd, archid ply, bhutan board, dura board mysore chip board ltd 13 plywood for general purposes dura ply, archid ply, bhutan board,archid board, century, durian, mysore chip board ltd 14 decorative laminates archid lam, sunmica, merino, lam, mysore chip board,greelam 15 terrazzo tiles ntc, nitco, eurocon, duracrete 16 glazed ceramic/non skid wall/floor tiles kajaira, johnson, agl, qutone , somany, nitco, orient bell ,vitero, sunhearrt ceramik, varmora 17 vitrified tiles (polished, unpolished & glazed, normal/ anti skid) kajaira, johnson, agl, qutone , somany, nitco, orient bell,vitero,sunhearrt ceramik, varmora 18 hdpe storage water tanks sintex, supreme,plasto,polycon 19 sanitary appliances /fittings(chinaware) hindware,parryware,cera,jaquar, kohler, prayag aproyale,somany 20 water closet seats and cover (solid bakelite) thermostat moulded toilet seat cover parryware, jaquar, prayag somani,commander,cera,neycer 21 pvc flushing cisterns hindware, commander, parryware, cera ,jaquar, johnson pedar, neycer 22 stainless steel kitchen sink with or without draining board, plate rack nirali,cera,diamond,jainco,shakti prayag, (silver shine) m/s bluestar sanitary industries 23 ball valves (horzontal plunger type) dripless faucets india, flowjet , ball valves inida. 24 shower roses chromium plated (swivel type) gem,jaquar, jal 25 bath room fancy fittings jaquar,gem,marc, jalangi 26 bib taps and stop taps (cp),pillar tap, fancy fittings jaquar, parko, gem, marc 27 bathroom cabinets jaquar, cera, commander, parryware .... more in document

Central Government/Public Sector

TRN :49055227 | 29 May, 2025

Tender Value : 29.12 Lacs

Tezpur - Assam

Tender for spl repair/replacement to ber dg sets at naa under ge (n) tezpur spl repair/replacement to ber dg sets at naa under ge (n) tezpur; 1 supply,installation,testing and commissioning of silent diesel engine driven generating set 82.5kva (66kw with 105 bhp ,pf0.8 lagging) 415v,3 phase,4wire with amf panel and enigne as per is:10001/10002 and alternator as per is: 13364 complete with relay panel and switch gears for automatic starting on main failure control panel having meter and sound proof canopy as per cpcb iv norms and fuel tank(capacity should not less than 12hr continue operation), foundation as per oem instruction etc complete all as specified and directed by engineer-in-charge . note:- (i) any left out standard accessorieswhich are not mentioned above for smooth functioning of the dg set shall be included in the quoted rate without any extra cost.(ii) the dg set shall be factory tested by the rep of accepting officer before dispatched.cost for the same shall be deemed included in the unit quoted rates. (iii) cost of testing of dg set on site as per iem direction as per ca provision is included in this rate. (iv) cost of foundation of dg set is deemed to be included in this rate and should be done as per drawing provided by manufacturer of dg set as per requirement of site. (v) cost of connection of all existing cable deemed to be included in quoted rate. 2 m&l for earthing complete with galvanised steel earth plate electrodesize 600 x 600 x 6.3 mm thick, burried directly in ground, (earth pit not less than 3.25 m deep below ground level) with top edge of the plate not less than 2.5 m below ground level connected to galvanised iron strip 32 x 6 mm as earthin lead strip by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no 3 connected to earthing test point all as specified or indicated including testing on completion, surrounded from all sides by mixture of charcoal and common salt and electrode by means of steel and gi pipe light grade 40mm dia bore for watering funnel with wire mesh. ci cover with frame, pcc chamber pit with pcc 1:3:6 type c-2 excavation and earth work all as shown in electrical plate no 3 connected to earthing test point all as specified and directed.note:-1. the unit rate includes for protection gi pipe and watering pipeof 40 mm bore including excavation for earth pit in any type of soil/ disintegrate rock.2. contractor has to bring agriculture soil from outside of defence land and fill in earth pit to achieve desired result as the soil resistiviy is very high.3.the cost ofgi strip of size 32 x 6 mm from top of earth plate upto 7.5 meter above ground level is deemed to be included in the unit rate of above item.4. all the joints in gi strip and connection with earth plate to be weldedand in addition by proving brass nut bolt and washer.5. cost of welding and nut bolts are deemed to be included in the unit rate. 6. contractor has to disposeoffthe excavated soil in open land up to a distance of600 mtr from earth pit.

Local Bodies

TRN :49055298 | 16 May, 2025

Tender Value : 2.00 Lacs

Sikar - Rajasthan

Tender for tender for in mahanarega and other development schemes (if required) rate contract for the supply of construction materials/services for new construction and repair works to be done in the year 2025-26. - ghadhla kankar jhajhrha mud masala , lime , cement , fine aggregate , fly ash , sand gravel , grit stone brick , stone pattiya , precast tiles , vitrified , cement interlocking wood with fitting , iron , structural steel , winding wire , iron girder , barbed wire , iron net , glass color paint , modular socket outlet , enamel paint ., bitumen tax board , g i sheet , sheet , pipe , road roller , truck , vehicle hiring , compressor , dumper , tractor with scraper , ghisai machine operator , cultivator , manpower services , rolling shutter, ferro cover , tiles , stone , kerb stone , pipe , putti , , varnish , flange , g i band , sluice valve , submersible pump set , sing phase head , handpump , connecting rods , fly ash brick , ordinary soil , hard soil , disintegrated rocks etc

State Government

TRN :49055303 | 20 May, 2025

Tender Value : 3.49 Lacs

Howrah - West Bengal

Tender for construction of drain with cover from raj chandrapur primary school to welfair socity

Central Government/Public Sector

TRN :49055340 | 31 May, 2025

Tender Value : 49.00 Lacs

Pune - Maharashtra

Tender for tender for welcome maint to offrs md accn under age br-i of ge (south) pune; 1 m&l for preparation of old decorative surfaces of ceiling including cornices (plastered or un-plastered) by brooming down and scrapping wherever necessary and applying one coat of white wash complete all as specified and directed 2 m&l for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered)of any description, sand papered and dusted and applying one coat of oil bound distemper of any tint complete all as specified and directed. 3 m&l for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered)of any description, sand papered , and dusted including complete removal of existing surface of walland applying two coats of oil bound distemper over and including a coat of 2mm thick wall care putty complete all as specified and directed 4 m&l for preparation of old painted wooden surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed 5 m&l for preparation of old painted steel surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed 6 m & l for preparation of surface of any description (plastered and old decorated) over 10 cm width or girth including removing of existing treatment completely and applying two coats of weather proof exterior paint complete all as specified and directed 7 m&l for preparation of old painted surfaces of walls by brooming down or steel wire brushing , scraping down soot, moulds, moss and efflorescent salt etc surface of any description (plastered and old decorated) over 10 cm width or girth and applying one coatof weather proof exterior paint complete all as specified and directed 8 m & l for preparation of surface of any description (plastered and old decorated) over 10 cm width or girth and applying one coat of luster paint complete all as specified and directed 9 m & l for french polishing on surfaces of any description, exceeding 10 cm width or girth over and including a coat of a coat of wood filler including cleaning and preparation of old wooden surfaces complete all as specified and directed 10 m & l for applying two coatsof oil bound distemper on walls over and including a coat ofpriming with chalk whitening including preparation of new plaster surfaces complete all as specified and directed 11 m&l for applying three coats of white washon ceiling and including preparation of new plaster surface complete all as specified and directed 12 m&l for applying two coats of cement base paintover and including a coat of alkali resistant primer on walls including preparation of new plaster surfaces complete all as specified and directed 13 m & l for preparation of brooming down or steel wire brushing, scraping down soot, moulds, moss and efflorescent salt etc and applying one coat of cement base paint over and including a coat ofalkali resistant primer on walls including preparation of oldsurfaces complete all as specified and directed 14 taking down cement plaster from old brick / stone masonry walls etc. including racking out joints, hacking for keys and scrubbing down with water complete all as specified and directed. 15 m&l for 15 mm thick plaster in cm 1:3 on concrete surfaces finished even and smooth using sagol finish on ceiling complete all as specified and directed 16 demolition of brickwork masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed. 17 m&l for old sizefly ash bricks, straight or curved on plan exc. 6 m mean radiusbuilt in cm 1:6 complete all as specified and directed 18 m&l for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 complete all as specified and directed 19 m&l for rendering 20 mm thick plaster in two layers on stone masonry surfaces or on other than fair faces of brick / pcc block masonry of walls (first layer 10 mm thick in cement mortar 1:6 and second layer 10mm thick in cm 1:6) and finishing the surface even and smooth without using extra cement complete all as specified and directed. 20 m&l for rendering 20 mm thick plaster in two layers on stone masonry surfaces or on other than fair faces of brick / pcc block masonry of walls (first layer 10 mm thick in cement mortar 1:6 and second layer 10mm thick in cm 1:4 mixed with wpc as per manufacturer’s instructions) and finishing the surface even and smooth without using extra cement complete all as specified and directed.note :- wpc shall be measured and paid separately as supply only under respective item of boq. 21 m&l for rendering 15 mm thick on fair faces of brick work / concrete surfaces in cement mortar 1:4mixed with water proofing compound as per manufacturer’s instructions, finished even and smooth without using extra cement complete all as specified and directed.note :- wpc shall be measured and paid separately as supply only under respective item of boq. 22 m&l for rendering 15 mm thick on fair faces of brick work in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed 23 m&l for pcc 1:3:6 type c-1, (using 20mm graded stone aggregate) of75mm thick, laid in alternate bays as in path and plinth protection including finishing the surfaces even andsmooth using extra cement, complete all as specified and directed 24 s&f in repairs pvc connection 60cm long 15mm dia with 2 nos. pvc nuts repairs complete all as specified and directed. 25 demolition of cement concrete in ground floor and pavings n. exc. 15 cm thickness (below or above gl), complete all as specified and directed. 26 demolition cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 27 m&l glazed coloured digital printed ceramic tiles of size 600x300x7-8mm thick in vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour tiles with and including 15mm thick backing coat in cm 1:4 including triangular filleting in cm 1:4 on top edges including dismantling of old unserviceable tiles including backing coat of any description and removal of debries & dismantled materials complete all as specified and directed 28 m & lfor water proofing treatment to sunken slab, walls,etc. shall be carried out as specified below and as directed by engineer-in-charge:-(a) dismantling & remove the existing lean concrete completely and clean the sunken portion of toilet / baths / wcs / kitchen thoroughly remove laitance, dirt, dust etc.(b) form angle fillet of size 40 mm x 40 mm along the junction of wall and floor by using polymer modified mortar (“ dr fixit” pidicrete urp” or equivalent).(c) sanitary pipes entering through walls and floor shall be sealed with “dr fixit bathseal tape” and the gaps to be grouted with non-shrink cementitous grout “dr fixit bathseal grout” or equivalent. nahani traps etc to be fitted securely and the gaps around it to be grouted in the same manner.(d) apply one coat of a bitumen-modified polymer coating “dr fixit bathseal plus” or equivalent on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet and applying second coat of the same coating on the angle fillets and allow it to dry completely. contd...... 29 (e) in the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. extend the coating upto150mm above the ffi. above ffi, another cementitious waterproofing waterproof coating “dr fixit pidifin 2 k” or equivalent to be further applied right upto 2.1 m to waterproof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hoours and allow to dry completely.(f) after 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed m 15 type b0 mixed with integral wpc (liquid) laid to stope 1:60 towards outer face of wall. provide 40 mm od upvc pipe at the lowest point with 300 mm projection beyond the outer face of the wall. then fill up the sunken portion with lean concrete 1:5:10 type e2.(g) after completing plumbing work in the toilet/wc/bath/kitchen, floor, tiling work (floor and dado) to be carried out by using suitable tile adhesives and ready to make tile grouts of approved makes such as dr fixit, fosroc sika, mc buchemie, roff, etc. note: lean concrete 1:5:10 type e-2 shall be measured and paid separately under respective item of boq. 30 m&l for pcc 1:5:10 type e-2 using 40 mm graded brick aggregate as in filling sunken portion, complete all as specified and directed. 31 m&l for 25 mm thick pcc 1:2:4 type b-1 (using 20mm graded stone aggregate) as in leveling course or pcc padding, finished the surfaces fair & even, complete all as specified and directed. 32 m&l for cleaning and removing all scale and dirt, etc, from tanks n. exc. 500 ltrcapacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed. 33 m&l for cleaning and removing all scale and dirt, etc, from tanks exc. 500 ltrs but n. exc. 1000 ltrcapacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed. 34 m&l for cleaning and removing all scale and dirt, etc, from tanks exc. 1000 ltrs but n. exc. 2000 ltrcapacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed. 35 m&l for granite (of any type) work (table rubbed and polished) 18-20mm thick as in steps, jambs, pillars, window- cills,cookingplatforms, as counters of any radiuos and like setting in neat cement slurry including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 20mm thick screed / backing coat in cement mortar (1:4)including dismantling of old unserviceable slab / tiles including screed bed of any description and removal of debries & dismantled materials complete all as specified and directed 36 rounding (half) of edges of granite stone slabs , as in steps, cooking plateform slab and other similar situations complete all as specified and directed. 37 s&f in repair cascade type (coloured) floor mounted single piecewater closet withpp soft close slim seat cover , hinges, dual flush cistern fittings, fixing accessories and accessories set , size 365 x 675 x740 mm, strap -220 mm pipe etcconnected to pipe complete all as specified and directed by engr in charge confirming to cat no. esc-wht-851s220sppsm essco (jaquar)or of equivalent make as specified here-in-after complete all as specified and directed 38 s&f in repairs glass coner assembly cosisting of 5.5 mm thicksheet glassround(9 x 9 ) with satinless steel railing, complete all as specified and directed 39 s&f inrepairs satinless steel robe hook (khuti) with5hook, complete all as specified and directed 40 s&f in repairs sink cock with swinging casted spout with aerator(wall mounted model) conforming to cat no. orb-105347 essco (jaquar) or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 41 s&f cp towel ring round with round flange conforming to cat no acn-1121 bn of jaquar / 9218 of prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 42 s&f in repairs brass chromium plated shower rose 100 dia with 235 mm long arm with or without swivel joints, including fixing to steel pipe or union, complete all as specified and directed 43 s&f in repairs brasscp wall mixer3- in-1 system with provn for both hand shower and overhead shower complete with 115 mm long bend pipe connecting legs and wall flange (without hand & ovwer shower ) conforming to cat no.ste-107281 stellaessco (jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 44 s&f in repairs cp 15 mm fancy long body bib taps brasswith wall falnge & aeratorconforming to cat no. sqt- 512kn essco ( jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 45 s&f in repairs soap dish cat no. acn-1131n jaquar / ba-259 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 46 s&f in repairs cp toilet paper holder conforming to cat no. acn-1151 n of jaquar / ba-38 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 47 s&f in repairs cp towel rail 20mm dia and600mm long including brackets conforming to cat no. acn-111n of jaquar/ ba-20 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 48 s&f in repairs health faucet cat no. ald-583kn of jaquar/ bea-85 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 49 s&f in repairs angular type stop cock with flangeconforming to cat no.apr -101053 essco of (jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 50 s&f in repairs cp 2 way bib cock with wall flange conforming to cat no. ste-107041,essco ( jaquar) , cera orequivalent cat part of makes as specified here-in-after, complete all as specified and directed 51 s&f in repairs cp pillartaps swan longneckwith aerator15mm bore fancy type with wall flange conforming to cat no orb -105001n essco ( jaquar) or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 52 s&f in repairs stainless steel towel rack with lower hangers, 600mm long conforming to cat no. can-1181fhs of jaquar or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 53 taking up or down steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and directed for following size of pipe :-(a). 15mm bore. 54 (b). 20mm bore. 55 s&f of following dia gi pipe, medium grade including with all fitting & fixtures, fixed on walls and ceilings or laid in floors etccomplete all as specified and directed.(a). 15mm bore 56 (b). 20mm bore. 57 re-fixing only following dia gi pipe, medium grade including with all fitting & fixtures, fixed on walls and ceilings or laid in floors etccomplete all as specified and directed.(a). 15mm bore 58 (b). 20mm bore. 59 m&l for cutting chases, pinning in, concrete, block /brick or stone walling & making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing and making good, cutting n. exc. 10 cm girth, complete all as specified and directed. 60 s&f pvc (swr) 110mm bore pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall including dismantling of old unserviceable breaking up drain pipes pvc or ac set in cm or solvent,complete all as specified and directed.note for item nos. 55 & 56:- rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building. 61 s&f pvc (swr) 75mm bore pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall including dismantling of old unserviceable breaking up drain pipes pvc or ac set in cm or solvent,complete all as specified and directed. 62 s&f pvc (swr) bends any radius 110 mm bore complete all as specified and directed. 63 s&f pvc (swr) bends any radius 75 mm bore complete all as specified and directed. 64 s&f pvc (swr) vent cowl 110mm bore, complete all as specified & directed. 65 s&f in repairs pvc (swr) branch piece, (double y) equal or unequal of 110 mm bore, complete all as specified and directed 66 s&f in repairs pvc (swr) branch piece, (double y) equal or unequal of 75mm bore, complete all as specified and directed 67 s & f 110mm pvc (swr) wc connector bent type complete all as specified and directed. 68 s&f pvc (swr), 75mm dia outlet floor trap, plain with grating including jointing with solvent cement, fixed to cement concrete type b1 1:2:4, complete all as specified and directed. 69 s&f pvc (swr), 75mm dia outlet multi floor trap, plain with grating including jointing with solvent cement, fixed to cement concrete type b1 1:2:4, complete all as specified and directed. 70 m&l for cutting, screwing & threading of existing 15mm bore steel tubing for alterations or additions (each cut measured) complete all as specified and directed 71 m&l for cutting, screwing & threading of existing 20mm bore steel tubing for alterations or additions (each cut measured) complete all as specified and directed 72 m&l for cutting, screwing & threading of existing 25/32mm bore steel tubing for alterations or additions (each cut measured) complete all as specified and directed 73 taking down chowkhat or frames n. exc. 1.5 sqm each with shutter without taking off shutter from the frame complete all as specified and directed. 74 taking down chowkhat or frames exc. 1.5 sqm but n. exc. 4 sqm each with shutter without taking off shutter from the frame complete all as specified and directed. 75 taking down shutters of any description exc. 1 sqm and not exc. 2 sqm each and remove from site, complete all as specified and directed. 76 s&f in repairs vitreous china, squatting pan, orissa pattern, size 580 x 440 mm white, with integral foot rest, including concrete bedding and pvc flushing cistern 10 ltr capacity including all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed. 77 s & f in repairs, vitreous china wash basin, white, flat back, size 550 x 400 mm with brackets, inc. cutting for & pinning in ends of brackets, including32 mm dia brass cpwastecouplingand32 mmdia low density polyethylene(ldpe) pressure rating 6 kg / cm² as waste pipe complete all as specified and directed 78 s&f in repairs vitreous china wash down water closet pan, pedestal white, including fixing bolts etc including pvc seat cover white with flat bottom including ms, cp or aluminium anodised hinge devices including pvc low level flushing cistern 10 ltr capacity with all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed. 79 s&f in repairs ewc seat cover of any pattern including cover and mild steel chromium plated hinging devices of any colour, complete all as specified and directed. 80 s&f in repairs, stainless steel plate rack of size 36 inch x 30 inch x 10inch, made out of 0.63mm thick stainless steel sheet (grade 304), s s screws and round pipe,fixed to wall with screws complete all as specified and as directed 81 s&f in repairs flexible waste pipe of 32 mm dia suitable for wash hand basins, sink etc of suitable length, complete all as specified and directed 82 s & f in repairs spindles of any size suitable for concealed mixer valves, stop valves, angle cock, fancy taps including knob heads complete all as directed by engineer-in-charge. 83 s & f in repairs kitchen or laboratory sinks made of stainless steel 1mm thick sheet with plugs, washers, and wastes coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, bowl size 560x460mm including coupling etc complete all as directed by engineer-in-charge. 84 s&f in repair high density 40mm bore polyethylene pipes (hdpe) of pressure rating 6 kg/cm2 fixed to wall or in floors with necessary socket, elbow & bendetc complete fixedto wall or in floors etc complete all as specified and directed. 85 s&fin repair pvc low level flushing cistern 10 ltrs capacity with and including all internal fitting, pair of bracket, including inlet / outlet pvc pipe connections etc. complete all as specified and directed 86 m&l for joint free non-skid ceramic coloured tiles 7 to 8 mm thick area of each tiles exceeding 0.11 sqm but not exceeding 0.18 as in floors, set an jointed in neat cement slurry and pointed in white or coloured cement to match including laid over and including 20 mm thick screed bed in cm 1:6 including taking of old existing unserviceable tiles of any type including screed bed and removing of debries & dismantled materials etc. complete all as specified and as directed 87 m&l for coloured vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.16 sqm but not exceeding 0.36 sqm as in flooring, set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over and including 20mm thick screed bed in cm 1:6 with including taking of old existing unserviceable tiles of any type including screed bed and removing of debries & dismantled materials etc. complete all as specified and as directed 88 s&f in repairs 20mm dia aluminium powder coated, fancy type curtain rod medium grade fixed in and including bracket, stops roller etc complete all as specified and directed 89 s&f stainless steelfency type caps / side bulbs etc. suitable for 20mm dia curtain rod pipe complete all as specified and directed. 90 s & f pressed steel frames for doors with one & more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified size of frame 125 x 60mm including ms hold fast - 6 nos. and ms cold rolled 100mm size butt hinges welding to existing ms frame including pcc bed block in 1:2:4 type b1 for hold fast and cement concrete 1:3:6 type c1 (12.5mm graded stone aggregate) for filling in ms hollow frame complete all as specified and directed. 91 s & f pressed steel frames for doors with one & more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified size of frame 125 x 60mm including ms hold fast - 3 nos. and ms cold rolled 100mm size butt hinges welding to existing ms frame including pcc bed block in 1:2:4 type b1 for hold fast and cement concrete 1:3:6 type c1 (12.5mm graded stone aggregate) for filling in ms hollow frame complete all as specified and directed. 92 s&f pvc door frame of size 50mm x 47 mm made out of 5mm plain colour pvc sheet reinforced with ms square tube, suppling & fixing in opening as per specification and drawing. 93 supply and fixing factory made solid pvc shutters,30 mm thick (style) consisting of frame made out of ms tube for top and bottom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strips of 20mm width stuck inside with solvent cement for stiles and plain cover pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panneling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rail with suitable pvc sheet beading, and joined together with solvent cement, supply and fixing in the frame at site as per specification and drawing. 94 s&f 300 mm long aluminium alloy, anodised , sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy fixed complete all as specified and directed. 95 s&f 200 mm long aluminium, anodised, barrel tower bolts of extruded section isi marked complete all as specified anddirected. 96 s&f 100mm size extruded aluminium anodised alloy handles, fabricated type, isi marked complete all as specified anddirected. 97 s&f pvc (swr) gully trap 125x110mm, setting and jointing with solvent cement, complete all as specified and directed. 98 s&f 100 mm long butt hinge, alum electroplated, heavy weight, cold rolled mild steel and fixed complete all as specified and directed. 99 s&f in repairs 600 x 450mm beveled edge lookingmirror of selected quality glass, mounted on 6 mm thick ac built board or commercial ply board and fixed to wooden plug with chromium plated brass screws and cup washer etc. complete all as specified and as directed 100 s&f aluminium powder coatedthree track sliding window with two or more shutters with & including 4mm thick tinted glass, one shutter of stainless steel wire cloth 0.36 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle, lock etc using pvc beadingetc using following sections of `jindal aluminum ltd or equivalent in ajit india pvt ltd or crystal bombay, as approved fixing to stone masonry walls with & including ist class teak wood plugs of size 20mmx20mm at an interval of 0.5m around the track including drilling holes etc complete all as specified and directed:(a) frame bottom20620(b) frame top& side 20681(c) shutters top & bottom 20844(d) shutter inter lock 20724(e) handle (side) for 20606 shutters 101 s&f ventiltors / louvers with partially guaged shutter using 5 mm thick x 10 cm wide frostedglass strips andby using of following aluminium powder coated sections conforming to catalogue of jindal or of equivalent make including with rubber beading etc, complete all as directed by engr-in-charge.(a) sp20048(b) glazing clips19352 102 s & f150 mm length floor door stopper of brassbody and tongue, hard drawn steel spring complete all as specified and directed. 103 s&f of 18/19 mm thick block board, grade i quality exterior grade type with decorative face veneer on both faces including lapping of edges fixed with screws to timber frame work as in cb partition and shelf and other works complete including dismantling of old unserviceable boards of any type complete all as specified and directed 104 s&f continuous (piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm, complete all as specified and directed. 105 s&f in replacement 100 mm brass fancy type cupboard handle fixed with nuts, screws and washer of brass polished, complete all as specified and directed. 106 s&f in repairs magnet catches and striking plate, complete all as specified and directed 107 removing building materials etc to a distance exceeding 5 km, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed. 108 m&l for gypsum ceiling board,pre-painted, perforated finish, 600x600x8 to 9mm thick in size of approved brand / make, laid over and including grid work of size 595 x 595mm, made out of 0.5mm thick g.i. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle, hung from ceiling by using 2 mm thick g.i. suspension wires spaced at 1200 mm on main runners including making niches for fans & light , complete all as specified and directed 109 all as per item no.103 but repair only to the existing false ceilings of any description complete all as directed by engr-in-charge 110 dismantling of wall / ceiling boards including snap grid of any thickness including cover fillets, complete all as specified and directed. 111 s&f 4 mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beadings in square n. exc 0.5 sqm in each pane, including hacking out old broken glass if any (any thickness, quality & size), complete all as specified and directed. 112 m&l for machine cut cudappah stone slab one side pre-polished, 30-40mm thick as in kitchen platform base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15 mm thick screed bedding layer in cm 1:4 including dismantling of old unserviceable slab / tiles including screed bed of any description and removal of debries & dismantled materials complete all as specified and directed 113 s&f of 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sideincluding 5mm thick,1st class hw (tw) beading all around on edging andcomplete all as specified and directed by engr-in-charge 114 m&l for 35mm thick iind class hard wood glazed and skeleton shutters, openrebated and prepare to receive glass (with sash bars), guage etc divided into squares with plain, chamfered or rounded, mitered and rebated sash bars any number, size of members of shutters as specifie in clause 8.24(a) of ssr part-i 2009, complete all as specified and directed. 115 m&l for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description exc. 10 cm width or girth, including preparation of surfaces, complete al as specified and directed. 116 m&l for applying two coats of synthetic enamel paint over acoat of red oxide primer on new steel surfaces exc. 10 cm width or girth, including preparation of surfaces, complete al as specified and directed. 117 m&l for 2nd class hard wood wrought plain fillets square, rectangular or triangular in section clean sawn secured with screws, sectional area exc. 13 sqcm but n. exc. 25 sqcm etc complete including dismantling of timber fillets from cabinet / cupboard frame, complete all as specified and directed 118 s & f in repairs gun metal, globe gate valves(class i), with iron wheel head,screwed both ends for iron pipe, isi marked, all as specified and directed for the following bore dia of pipe:-(a) 15mm bore. 119 (b) 20mm bore. 120 (c) 25mm bore. 121 s&f 25/32mm bore ball valve high pressure of ptmt with epoxy coatedaluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms), complete all as specified and directed. 122 s&f 20mm bore ball valve high pressure of ptmt with epoxy coatedaluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms), complete all as specified and directed. 123 s&f 15mm bore ball valve high pressure of ptmt with epoxy coatedaluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 142 gms), complete all as specified and directed. 124 supply only liquid water proofing compound, complete all as specified and directed. 125 s&f in repair for stainless steel wire cloth 0.36nominal dia of wire and average width of aperture 1.4mm and fixedwith stainless steel staple to wooden / steel frames, complete all as specified and directed

State Government

TRN :49055368 | 20 May, 2025

Tender Value : 2.00 Lacs

Alwar - Rajasthan

Tender for tender for supply of stationary - white paper rim, carbon paper, photostat paper rim, paper, allpin, paper cutter, cello tape, file cover, file tag, stapler, stapler pin, file pad, stamp pad, stamp pad ink, gum bottle, envelope, register, strip file, cello tape, pen, calculator, display stand for table, spiral diary, punching machine, duster, clip board, rubber band, note sheet, etc.

State Government

TRN :49055381 | 23 May, 2025

Tender Value : 1.49 Lacs

Medinipur East - West Bengal

Tender for construction of concrete cover drain from rafikul khna house to jahedul khan house at dhalhara paschim

Central Government/Public Sector

TRN :49055382 | 27 May, 2025

Tender Value : 38.20 Lacs

Lahul And Spiti - Himachal Pradesh

Tender for tender for provn of 04x50 kl grp water tank with connected items for water storage at sumdo in the area of age e/m (we) pooh under ge 863 ews; 1 excavation in trenches not exc 1.5 meter wide and not exc 1.5 metre in depth and getting outin soft/loose soil, for laying underground pipe etc, complete all as specified and directed . 2 returning, filling in incl spreading ,levelling watering and well ramming in layer n exc 25cm thick each layer , in soil, complete all as specified and directed . 3 removing excavated surplus materialto a distance n exc 50m and depositing where directed at level n. exc 1.5m above the starting point in any type of soil, complete all as specified and directed . 4 supply and laying 100 mm bore gi tubing medium grade including all fixture/ fittings for connection laid in trenched as per site requirement and directed by engr-in-charge. 5 supply and fix valves, sluice, flanged of class 1.6 pn, 100 mm (4”) dia complete all as specified and directed . 6 supply and fix non return sluice valve 100 mm dia complete all as specified and directed . 7 construction of brick masonary valve pit of size 600x600x600mm (internal dimension) incl necessary earth work and ms sheet 3 mm thick cover with angle iron frame 40 mm x 40 mm x 6mm including provision of suitable hold fasts to hold the frame, locking arrangement and lifting handle, duly painted with two coats of synthetic enamel paint over a coat of red oxide primer all as shown in drg held with ge office incl of tapping of 100 mm gi pipeline from existing 100 mm gi pipeline complete all as specified directed. 8 supply fixing and testing monoblockpump sets, electric driven 415 v, tp suitable foroutdoor type rating capacity7.5hp kw (5.5) inclusive of 40 metre head pump model kds 8.30 ++ code no d12010750210 size in mm 80x65 including star delta starterall as directed by engr-in-charge. 9 s&f of smc/grp panel tank for water storage confirming with is 14399:1996 (part i & ii) and is-4249:1967 for fire retardant & nsf uk certified of 50,000 ltr capacity of size 5.00x5.00x2.00 mtr complete including necceassary connection of all inlet, outlet pipes with pump &all other neccessary fitments requiredat site for installation on ground complete all as specified and directed by engr-in-charge.note : standard non – insulated smc panels hot pressed moulded uv stabilized made from sheet moulding compounds (smc) composing of glass fiber and formulationsmc panels - made by hot pressed process mouldedbottom panel - smc panel 1000 x1000 x 70 mm, convex shapedrain panel & outlet panels - smc panel 1000 x1000 x 70 mm special design for complete drainside panel - smc panel 1000 x1000 x 70 mm, 1000 x 500 x 70mmceiling panel - smc panel 1000 x1000 x 70 mmmanhole -smc panel 1000 x1000 x 70 mm with 700 mm x 700 mm locable lid.thickness of the panels - as per is 14399 (part i & ii) 10 special accessories:corner frame - hdg steel vertical corner angle at four cornerssealing tape – non toxic 3mm thick with high level of resistance to ageing and superior recovery from compression (make : norseal by saint gobain)steel bolts for panel joints - hdg nut-bolts – 8.8 grade – m12 x 40mm – 8 nos. per sideair vent – pvc - air vent dia 100mm with insect proof mesh in sidewater level indicators - aluminium body level indicator – transparent tube typeexternal reinforcement - isi marked painted c channel supports at every 1-meter except in the corner of steel with anti corrosive paint and it is tie with top external painted tie rods.internal roof supports - frp square hollow section for roof supports – 50x50x5mmladders external ladder with wall mounting arrangementinternal ladder frp (if tank height is more than 1 meter)connection fixing - inlet/ outlet/ overflow/ drain inlet, outlet, overflow & drain – 50nb (as per table d – bs10)g.i. flange type with 9” long thread and nipple.base frame grillage - as per site condition, suitable for tank size and capacity. made out from m.s. channels/ beams with anticorrosive paints.base frame shall be measured & paid separately under relevant items. 11 pcc 1:3:6 type c-2 using 40mm stone agg as in foundation, filling and mass concrete on retaining walls complete all as specified and directed by engr-in-charge. 12 material and labour for providing pcc 1:2:4 type b1 using 20 mm graded stone aggregate as in platform, filling and mass concrete, complete all as specified ansd as directed. 13 pre-cast cement concrete hollow block masonry type 1:3;6, exc. 10 cm in width and setting in cement mortar 1:6,complete all as specified and directed by engr-in-charge. 14 m&l rendering 15mm thick on brick masonary in internal surfaces in cm 1:4 finished even and smooth with sagol finishcomplete all as specified and directed.

Government Departments

TRN :49055388 | 21 May, 2025

Tender Value : 8.06 Lacs

Agra - Uttar Pradesh

Tender for tender for zone-1, ward no.-92, rawatpara roshan mohalla, work of preparing the floor along with repair of office building. - demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. 2 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge.15.7.4 in cement mortar 3 cleaning of the site for warkable etc. all complete. (non scheduled) 4 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:4 (1 cement : 4 coarse sand) (dsr 2023 sh-6.4.1 ) 5 brick work 7 cm thick with common burnt clay f.p.s. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. (dsr 2023 sh-6.8 ) 6 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,taircases and spiral stair cases above plinth level up to floor fiveevel, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).(dsr 2023 sh-5.3 ) 7 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more(dsr 2023 sh-5.22.6) 8 centering and shuttering including strutting, propping etc. and removal of form work for :columns, piers, abutments, pillars, posts and struts(dsr 2023 sh-4.3.3 ) 9 12 mm cement plaster of mix : 1:4(1 cement: 4 fine sand)(dsr 2023 sh-13.1.1 ) 10 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(dsr 2023 sh-10.1 ) 11 providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.fire retardant plywood conforming to is: 5509(dsr 2023 sh-9.126.2 ) 12 providing and fixing isi marked is:1341 m.s. pressed butt hinges bright finished with necessary screws etc. complete :)75x47x1.70 mm (dsr 2023 sh-9.55.3 ) 13 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side ofdhesive bonding quality conforming to is : 2046 type s including cost of adhesive of approved quality. 1.0 mm thick (dsr 2023 sh-9.127.2 ) 14 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre (dsr 2023 sh-13.41.1 ) 15 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture(dsr 2023 sh-1021sub head : 13 finishing13.48.3 ) 16 providing & fixing white vitreous china water closet squatting pan (indian type) along with “s” or “p” trap including dismantling of old wc seat and “s” or “p” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. long pattern w.c pan of size 580x440 mm (dsr 2023 sh-14.80.1) 17 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require white vitreous china flat back wash basin size 450x 300 mm with single 15mm c.p. brass(dsr 2023 sh-17.7.7) 18 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is: 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required(dsr 2023 sh-17.5.1 ) 19 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c. automatic flushing cistern, with fittings, standard size g.i./ pvc flush pipe for back and front flush with standard spreader pipes with fittings, g.i clamps and c.p. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: single squatting plate with 5 litre p.v.c. automatic flushing cistern(dsr 2023 sh-17.6.1 ) 20 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(dsr 2023 sh-11.55.1 ) 21 providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to isi : 12701, colour of opaque white or as approved by engineer-in- charge. the rate includes making necessary holes for inlet, outlet & over flow pipes. the base support i/c fittings & fixtures for tank shall be paid separately 22 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge100 mm nominal size dia 23 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge150 mm nominal size dia 24 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one stepcpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work - exposed on wall 15 mm nominal dia pipes 25 providing and fixing ptmt bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms 26 providing and fixing ptmt stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms) 27 mirror of superior make glass 60x45 cm 28 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 29 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 30 supply and fixing of light fitting switch board. (none sheduled) 31 supply and fixing wiring of light point. (none sheduled) 32 s/l/j of 20mm dia pvc cunduct pipe etc. all complete. 33 supply & fixing of wiring sub main. 34 supply & fixing of plug point 15mm. 35 lettering & painting of wall etc. all complete. 36 supply & fixing of 27watt. cfl etc. all complete. 37 carriage of materials by manual labour including loading, unloading and stacking for lead less than 01-50 mtrm.207.34+30.42 every 50 additonal meter 38 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 39 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 40 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.) 41 chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : light shade pigment using white cement 42 marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :raj nagar plain 43 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)(dsr 2023 sh-10.28 ) 44 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (dsr 2023 s h) 45 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 46 making ornamental painting with special design make by specialist painter laying of two coat birla white putty and design by asian paint including all material etc. all complete. (nn approved) 47 sub total 48 add/deduction rs. for estimate figure amount match 49 grand total

Related Searched Keywords : cover

List of cover Tenders

Tender for special repair of b veh garage of 257 fd wksp coy eme at 330 bde special repair to drain cover of strom drain line at cqa ffe aundh camp and provn of toilet block at 8 mahar under ge mh and rh khadki

Tender for construction of drain with cover from raj chandrapur primary school to welfair socity

Tender for construction of concrete cover drain from rafikul khna house to jahedul khan house at dhalhara paschim

Get cover Tender Alert...

Related Searched Keywords : cover

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us