Filters

List of power-press Tenders

List of latest power-press Tenders in Indian Tenders. Click on any power-press Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for power-press Tenders.

All-Tenders (38)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Government Departments

TRN :49022269 | 21 May, 2025

Tender Value : 8.46 Lacs

Agra - Uttar Pradesh

Tender for tender for zone-1, chhatta ward no. 27, bagh muzaffar khan, from saint john square to near garg homeo hall, hotmix road improvement work. - dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre, as per direction of engineer-in-charge. 2 supplying and stacking at site 53 mm to 22.4 mm size stone aggregate 3 supplying and stacking at site stone dust 4 preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 5 surface dressing one coat on old surface with bitumen of specified grade at the rate of 1.22 kg/ sqm of surface area with 1.10 cum of stone chippings 11.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity etc. complete: using bitumen emulsion (minimum 50% bitumen content- rs grade conforming to is : 8887) 6 providing and applying tack coat using bitumen emulsion conforming to is:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanicalbroomon bituminous surface @ 0.25kg/sqm 7 providing and laying dense graded bituminous macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of engineer-in-charge.50 to 100 mm average compacted thickness with bitumen of grade vg-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) prepared in batch type hot mix plant of 100-120 tph capacity 8 providing and laying bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of engineer-in-charge. 40/50 mm compacted thickness with bitumen of grade vg-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of aggregate) prepared in batch type hot mix plant of 100-120 tph capacity 9 providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatichermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, t&p, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of engineer-in-charge and accordance with applicable specifications. 10 reflective raised pavement markers (cat eye/ road stud) supply and flxing of raised pavement marker with made of plastic body of rpimi road stud shall be moulded from asa (acrylic styrene acrylonitrile) or hips (high-lmoact polystyrene) or acryloniilrile butadien styrene (abs) or any oiher suitable malerial approved by the engineer. the marker shall support aload of 13,635 kg tested in ccordance with astm d4280.the reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internaleflection of the lighl entring the lens face. lenses shall be mouled of methyl melhecrylate conforming io astm d78b of equivalent the slop or retro-reflecting surface shall preferably be 35+1-5 degree to base and the area of each relro _reflecling sllrface shall not be less than 13.00 sq.cm the marker height shall not be less lhan 10 mm and shall nol exceed 20 mm & width shall not exceed 130 mm. the base of the marker shall be flal within 1.3 mm all road studs shall be legibly marked wilh the name , lrade or other means of identification of the manufacture. epoxynslallations, excess adhesive around the edge of the malker, excess adheslve on the pavemenl and adhesive on the exposed surfaces of the markers shall be immedialely removed. the contractor shall submit a two year warranty for sal sfactory lleldeformance including stipulated retro-refleclance of the reflecting panel , to the engineer . ln addition a two year warranty foralisfactory infield perfonnance of the finished road marker shall also be given by lhe conlractor who carries out the work of fixing of reflective road ma*ers. ln case the markers are displaced , damaged . gel worn out or lose theireflectivity compared lo stipulated standards , the contractor would be reqlllred to replace allsuch markers within 15 days ofthe inlimation from the engineer. at his own cost the rate shall include all materlals, labour, t&p,ransportalion, insiallation and incidentals all complete as per direction of the engineer-in-charge 11 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 12 sub total 13 add/deduction rs. for estimate figure amount match 14 grand total

Co-operative

TRN :49022717 | 20 May, 2025

Tender Value : 0

Powayan - Uttar Pradesh

Tender for supply of hardware and general material and nut bolt items supply of hardware and general material and nut bolt items for season 2025-26 , description , norton make sander disk alkon gold plus. grit no. 80 size 100mm. , -do- 36 no. size 100mm , holdite in perfect liquid in ½ kg. tin. , white lead sakura make. , lead wire size 1mm in 500 gm roll. , emery cloths rough carbandom make. , carbandom make emery cloth medium. , -do- fine. , emery tape rough in 50 mtr. long size 2” carbondam make. , -do- fine , carbandom make emery paste in 400 gm rough. , -do- medium , -do – fine , annabond 112 (50 gms.) , annabond 666 (100gms). , araldite in 180 gms. , araldite in 1.8 kgs. , blue tube in 20ml. , loctite no. 270 in 50ml. , -do- no. 262 in 50ml. , rustoline in ½ ltr. tin. , teflon tape size ½” , -do- ¾” , -do- 1” , m.seal phata phat in 25gms. , graphite powder in ½ kg. tin. , braso in 100ml. , rubber hose pipe size 1” suitable for 10 kg./cm2 pressure and temperature 100 degree. , unique make complete rubber tyre coupling size px/tc/ph. , unique make spare tyresize px/tc/phdiscount. , rope pulley one groove , rope pulley two groove. , rope pulley three groove. , d-cycle cap. 2 ton. , -do- 5 ton. , -do- 10 ton. , cotton waste coloured. , garware make p.p. rope size 18mm (3/4”) with tc. , jyoti make pure rubber sheet size 1/8 , -do- size ¼ and above. , bearing sleeve jmc make different size , polyster wire sealing size 1 ton x 2 mtr. long. , -do- size 2 ton x 3 mtr. long. , -do- size 5 ton x 2 mtr. long. , indef make chain pulley block one ton capacity with 10 mtr. lift p-model with tc. , -do- 3 ton capacity with 10 mtr. lift. , rubber oil seal mykoda make different size , c.i.plumber block s.m.r make different size , tefflon rod size 50mm x 300mm. , brass shim 0.05x14”x48”. , brass shim size 0.1x14”x48” , -do- smoke grey. , -do- light grey. , -do- sky blue. , namda different size. , diamond make wire braided rubber hose pipe both side bsp fitting size ¼” x 800mm , -do- size ½” x1500mm. , audco make cock valve (plug valve) flanged end size 3” (80mm) regular pattern standard type wrench operated. , spring steel flat differentsize. , ms round different size. , en-8 rod different size. , ci pulley b-section groove no.3 size 4” dia. , -do- c-section groove no. 4 size 8” dia. , brass liner 40mesh x 2 ft. x 13.125 sft. , rubber hose pipe size ¾” for 100o temperature and working pressure 10kg/cm2 , ms perforated sheet hole size 5mm dia size width 900mm x length 2400mm x 3mm thick. , renold chain different size diamond make. , ms. square different size. , oil paper. , ms chain size 5mm , hydrolic connector size 3/8”x1/4” , -do- size 3/8”x3/8” , -do- size ¼”x1/4” , hose clamp suitable size 1”id pipe. , glass lubricator cap. ½ ltr. no.8 connection size ½” bsp. , brass shim 0.05mmx 14”x48” , -do- 0.10mm x 14”x48” , -do- 0.15mmx14”x48” , -do- 0.20mm x 14”x48” , gm solid rod different size. , brass rod different size , sight glass toughened size 210x15mm , hydrolic connector size ½”x14mm , burffi cut zali size 25mm (1”)x4ft. width x 10 gauge x51 ft. long. , glass wool , chcken wire netting 3ft. x 100 ft. , gi binding wire. , silicon bronze rod 1/8”. , double wire braidedsteam hose pipe size ¾” for pressure 21 kg. cm2 and temperature 205oc. , hindustan composite ltd. make brake liner size ¼”x3”. , loctite in 20ml no. 406 , m-seal pidite make , c.i. v belt pulley section c groove no. 4 dia size 7” , -do- section b groove no. 3 dia size 6”. , gun metal valve sant make , totem make die nut bsf size 3/8” , -do- size ½” , -do- size 5/8” , -do- size ¾” , power master tube exponder 42mm id x 45mm od. , copper rod size 1 ½” , cast steel steam valve wj make different size , copper tube pvc coating size ¼” , copper tube cutter , ss tube cutter size 16mm , copper pipe size 10mm x 1.5mm , push pull tee size 8x8x8mm , push pull connector male size ¼”xfemale size 8mm. , -do- size ½” x female 8mm. , pvc tube working pressure 12kg/cm2 size 8mm , brass connector with both side nut and female ¼” , brass nut size ¼” , brass ferrule size ¼” , brass connector size ½” male x ¼” female. , brass connector size 3/8”x1/4” , brass elbow with ferrule size ¼” , brass tee size ¼”x1/4”x1/4” , brass reducer size ½ x 1/4” , brass reducer size ½” x 3/8” , brass reducer size 3/8x1/4” , brass ferrule size 10mm , brass connector with nut and ferrule for size 10mm od , aluminium fitting make thread size ¼”x1/4” , -do- size ½”x1/4” , -do- size 3/8”x1/4” , -do- size ¾”x1/4” , aluminium elbow make thread size ¼”x1/4” , ss connector for with nut and ferrule for size 16mm od tube. , heavy duty plumber block for 22334 k bearing (634). , moscot make isi marked double rope safety belt. , indfos make pressure switchrange 0.5mm to 7 kg/cm2, ¼” bsp fittings. , hap/h.guru make pressure gauge 6” dia bottom entry ½” bsp range 0.21 kg./cm2 , -do- range 0.40 kg./cm2 , h.guru make /hap make pressure gauge dia size 2” range 0.10 kg./cm2 back fitting size ¼” , janatics make air filter regulator range 0.10 kg/cm2 with gauge glass zie ¼” , lp make butter fly valve with ss wafer size 1 1/2 “ , clamp for pipe size 1” , u clamp size ¾” , flat belt size 2”x4 ply. , elegator 45 nos. , hydroulic pipe od 20mmx15mm id suitable for 300 kg/cm pressure. , hydroulic ferrule for 20mm od tube. , hydroulic connector with nut size : 20mm , copper tube size 3/8” , brass ferrule size 3/8” , brass connector with nut size 3/8” , ci diaphragram size 80mm , ci diaphragram valve size 50mm , klinger make gauge glass size a-9 , isi marked ci butterfly valve size 40mm , isi marked ci butterfly valve size 100mm , usha martin ltd. make steel wire rope hemp core size 6/19x3/4”(e.d.inclusive agt m.vat) , isi marked nylon rope with t.c. size 20mm , multi screw driver kit.(jhalai make) , mitutoyo make dial indicator with magnetic stand. , lead wire (0.5) mm(500gram per roll) , steam valve high pressure flanged end size ½” , steam valve high pressure flanged size 1” , pu elbow size 8mm , pu connector size 8x8mm , air filter regulator complete with gauge. , cast iron globe value with ss part size 40mm , mud conveyor belt endless 600mm width 3 ply nylon 8mm thick. , sight glass toughened size 200x20mm , sight glass toughened size 100x20mm , ms sprocket 12 teeth x 50mm pitch. , dead nut size ½” , dead nut size 3/8” , brass elbow size 3/8”x3/8” , brass elbow size 3/8”x1/4” , pu tee size 8mm , gauge glass size ¾”x16” , cast iron reflex valve (horizontal +/vertical use) with gun metal working part flanged size 4”. , light resin bounded pads 1.64x1.22x50mm thick.(per sheet of 02 mtr) , becon make teco generator as per serial no. given by you. , becon make teco indicator as per your sr. no. , stainless steel nozzle for de superheating turbine type. , cast steel gauge glass assembly for reflex gauge klinger , pvc tail end flanged heavy duty size 8” , rubber insertion sheet size 5mm , pvc heavy duty end cap size 4” , power grip make heavy duty tin cutter size 12” , chisel , leader make ci butterfly valve with aisi 304 quality wafer size 4”. , leader make ci butterfly valve with aisi 304 quality wafer size 6”. , isi marked ci nrv with gm working part size 6” , teflon rod size 60mmx300mm , imported ph meter. , imported tds meter. , brass connector with 2 nut+2 ferrule 10mm , brass connector with 2 nut + 2 ferrule size 3/8”x3/8” , brass 3/8 male x ¼” female. , brass 1/4” male x 3/8 female. , brass connector complete size ¼”x1/4” , ci pulley close grain 7” -5 groove – b –section. , ci pulley close grain 10”-5 groove – b- section. , ci pulley close grain 13”-5 groove – c- section. , ci pulley close grain 16”-5 groove-c section. , brass connector with 2 nut + 2 ferrule complete. , copper coil size 3/8” od. , plaster of paris. , high pressure hose flexible with female end fitting size 3/8”x1 ½” , -do size ¼”x1 mtr. , dewrance plug sleeve set of 3 pcs size ¾” , rubber conical washer size ¾” , ci nrv with gm working part size 2 ½” , protector for gauge glass size ¾”x16” , v. belt pulley “c” section 4 groove size 7” , teflon rod size 35mmx300mm , -do-12x40 , high pressure hose pipe with both side size ½”x1 mtr. , -do- size ½”x2 mtr. , high pressure hose with bolt side size 3/8x1 mtr. , high pressure hose pipe with both side 3/8x2 mtr. , h.guru/hap make temperature gauge size 6” range 0-350c. , -do- 0-300c. with 3 mtr. capillary stem length 14” , isi marked ci sluice valve flanged end size 1 ½” , leader make gauge glass cock set size ¾” with ibr tc , m.s. nut bolt with washer , m.s. bolt full thread/half thread inch size 1/4 “ to 3/8” , -do- size 1/2 “ to 1 ½ “ , -do- mm size 6 to 10 mm , -do- mm size 12 to 24mm , ms nutsize ¼” to 1 1/2 “ , ms nut mm size 6mm to 24mm , ms washer different size , spring washer bbbb make different size . , h.t. bolt unbrako make different size , split pin champion make different size , ms rivet different size. , alluminium rivit size ¼”x1/2” , nylock nut size 1” , nylock nutsize 24mm , nylock nutsize 27mm , stainless steel allenkeybolt size 8x 25 mm , stainless steel allenkeybolt size 12 x 25 mm , stainless steel allenkeybolt size 12x40 mm , stainless steel allenkeybolt size 12x50 mm , steel screew , s.s. bolt with nut size- 5/8 x 1-1/2apl make , s.s. bolt size- 8 x 25 mm apl make , s.s. bolt size- 8 x40 mm apl make , s.s. bolt size- 8 x50 mm apl make , s.s.nut size- 8 mm apl make , g.i.bolt size- 8 x 80 mm , g.i.bolt size- 6 x75 mm , g.i.bolt size- 10 x100 mm , m.s. fastner bolt size- 12 mm

Local Bodies

TRN :49022842 | 16 May, 2025

Tender Value : 8.07 Lacs

Raebareli - Uttar Pradesh

Tender for tender for construction work of 04 m.m.i.g. buildings in amol vihar yojna - earth workinfoundation in ordinary soil ( loamclay,or sand) including lift upto 1.5 metre ( 5fts) and lead upto 30m. (100fts.)andincludingfilling watering and raming of excavatedearthintotheplinth and removal anddisposalof surplus earth and directedby the engineer - in - chargeupto a distance of 30m. ( 100 fts ) from the foundation trenches. 2 earth work in cutting or in embankment in ordinary soil, excavation to be in form of regularpitsnotexceeding1/2 mt (20) in depth and earthwork inembankmenttobein20cm (8) layers, including ramming anddressingthesurfaceto requiredlevelsandslopesand alsoincluding1.5mts(5fts)lifts and 30mt (100fts) lead. the earth from cutting to be used in makingembankmentsortobe deposited as spoil banks with in30mts(100fts)distanceas directedbytheengineerin charge,includingcartageof8km. 3 concrete with4cm. (1*1/2) gauge brick ballast, fine local sand of 1.25 fineness modulous andcementin proportion of 8: 4:1infoundationsand under floors, includingsupply of allmaterials,labourand t&p etc.requiredforpropercompletion of the work. 4 providingandlayinginposition specified grade of reinforced cement concrete, excluding cost of centering, shuttering, finishing and reinforcement in 1: 11/2 : 3 ( 1 cement, 11/2 coarse sand , 3 20mm graded stone aggregate. 5 foundations,footings,basesof columns, etc. for massconcrete 6 columns,pillars,piers,abutments, posts and struts 7 suspended floors, roofs, landings, balconies and accessplatform 8 mildsteelorironinplain worksuchasreinforced concreteorreinforced,brick work(when notincluded inan over all rates ) wroughtto required shapeasnecessary includingbendingforproper completion of the work and including supply of steel its wastagebendhooksand authorised over lapping shallbemeasured. 9 brick work in comman burnt clay (non-modular)bricks of class 150 in super structure aboveplinthlevelincluding supplyoflabour,materialand t&prequiredforproper completionofworkincement mortar 1:6 ( 1 cement: 6 coarsesand) 10 class150 brick work in1:4 cementand coarsesand mortarinsuper - structureforwallthickness 12 cms 11 12mmthickcementplasterof mix1:4(1cement:4coarsesand) 12 providing &layingof lightcinderfillingunderfloorof toilets & other sunken roofs. 13 providingandfixinginwall unplasticisedrigidpvcrain waterpipesconformingtois: 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermalexpansion,(i)singlesocketed pipes. 110 mm dia 14 providingwoodworkinframe ofdoors,windows,celerestory windowsandotherframes, wrought frames and fixed in positionwithholdfastlugsor withdashfastnersofrequired dia and lenghts (hold fast lugs or dashfastnersshallbepaidforseperately): sal wood 15 providingandfixingangleiron framesfordoors,windowsand ventilatorsofmildsteelangle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing t- ironframeortothewallwith dash fastener, including fixing of necessary butt hinges and screwsandapplyingapriming coatofapprovedsteelprimer, all complete as per the direction ofengineer-in-charge.(fordoorframes) 16 providingandfixingisimarked flush door shutter confirming to is:2202(part1)non-decorative type, core of blockboard constructionwithframeoffirst classhardwood andwell matched commercial 3 ply veneering with vertical grains or cross bands and face vineers on both facesof shutters:35mm thick including isi marked stainlesssteelbutthingeswithnecessary screws. 17 providingandfixingwiregauge shutterusinggalvanisedms wiregaugeofaveragewidthof apurture1.4mminboth directionwithwireofdia 0.63mm for doors, windows and celestorywindowswithhinges and necessary screws. 35mm thick shutter, with isi marked mspressedbutthingesbright finished of required size withsecond class teak wood. 18 steelworkweldedinbuiltup sections/framedwork, including cutting, hoisting, fixing inpositionandapplyinga primingcoatofapprovedsteel primer using structural steel etc. asrequired.ingratings,frames, guard bar, ladder, railings, brackets,gatesandsimilarworks(forwindow grills) 19 providingandfixingaluminium towerbolts,isimarked, anodised (anodic coating not lessthangradeac10asper is:1868) transperent ordyed to required colour or shed, withnecessary screws etc. complete. 150 x 10mm+ 20 250 x 10 21 providingandfixingaluminium sliding door bolts, isi marked anodised anodic coating not less thangradeac10asperis: 1868),transparentordyedto requiredcolourorshade,with nutsandscrewsetc.complete:250x16 mm 22 providingandfixingaluminium hangingfloordoorstopper,isi markedanodised(anodic coatingnotlessthangradeac-10asperis:1868)transparent ordyedtorequiredcolourand shed, with necessary screws etccomplete. twin rubber stopper. 23 mildsteelorironwork of heavy sizes and sections such as holdingdownbolts,holdfast, tie, rods gratings etc (when not included in an over all rates) wrought to required form, includingsupplyofsteel,bolts, nutsandwastageetcandtheir fixingrequiredtoproper completionofwork.(fortubular stair case railing) 24 providingandlayingvitrified floortilesindifferentsizes (thickness to be specified by the manufacturer) with water absorptionlessthan0.08%and conforming to is : 15622, of approved make, in allcolours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarsesand),includinggrouting the joints with white cement and matching pigmentsetc.,complete. size of tile 600x600 mm 25 providingand laying vitrified tilesin differentsizes (thickness tobespecifiedby manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in allcolours &shade,inskirting,riserof steps,over12mmthickbedof cement mortar 1:3 (1 cement: 3 coarsesand),includinggrouting thejointwithwhitecement& matching pigments etc.complete. size (600x600) 26 marblestoneflooringwith18 mmthickmarblestone,asper sampleofmarbleapprovedby engineer-in-charge, over 20 mm (average)thickbaseofcement mortar 1:4 (1 cement : 4 coarse sand) laid and jointedwith grey cement slurry, including rubbingand polishing complete with : udaipur green marble 27 providingandfixingfirstquality ceramic glazed wall tile confirmingtois:15622 (thickness to be specified by the manufacturer)ofapproved makeinallcolours,sheds exceptburgandy,bottlegreen, black of any size as approved by engineerincharge,inskirting, rizersofstepanddados,over 12mmthickbedofcement mortar1:3(1cement:3coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mix with pigment ofmatching shed complete. 28 providing and laying ceramic glazed floor tiles of size 300x300 mm(thicknesstobespecified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours suchaswhite,ivory,grey, fume red brown, laid on 20 mm thickcementmortar1:4(1 cement : 4 coarse sand), includingpointingthejoints with white cement and matchingpigment etc, complete. 29 providing and applying white cementbasedputtyofaverage thickness1mm,ofapproved brand and manufacturer, over the plastered wall surface to prepare the surface even andsmooth complete. 30 finishing walls with acrylic smoothexteriorpaintof required shade on new work (twoormorecoatapplied@1.67ltr/10sqmoverand includingprimingcoatof exterior primer applied @ 2.20kg/ 10 sqm) 31 wallpaintingwithacrylic emulsionpaint,havingvoc (volatile organic compound ) content less than 50 grams/ litre, of approved brand and manufacture,includingapplying additional coats wherever required, to achieve even shadeand colour. two coats 32 paintingwithsyntheticenamel paint of approved brand and manufactureofrequiredcolour togiveanevenshade:twoor morecoatsonnewworkover an undercoatofsuitable shade with ordinary paint of approvedbrand and manufacture 33 providing and fixing white vitreouschinapedestaltype water closet (european type) withseatandlid,10litrelow level white vitreous china flushingcistern&c.p. flush bend with fittings & c.i.brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proofcouplingofapproved municipaldesigncomplete, including painting of fittings and brackets, cutting and making good thewallsandfloorswherever required : w.c. pan with isi markedwhitesolid plastic seat and lid 34 providingandfixingwashbasin withc.i.brackets,15mmc.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making goodthewallswhereverrequire: whitevitreouschinawash basin size 630x450 mm with a pairof15mmc.p.brasspillartaps 35 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittingscomplete. semi rigid pipe 32 mm dia 36 providing and fixing cp brass bibcock of approved quality confirming to is: 8931 15mm nominal bore. 37 s/f of 15mm nominal bore cpvc pipe all complete. 38 providing and fixing cp brass angle valve for basin mixer and geyser points of approved quality confirming to is:8931 15mm nominal bore. 39 15mm nominal boare 40 providing and fixing cp brass shower mixer of 15 or 20mm bore including cp brass connection with angle valve of standard design and approved make confirming to is:8931 41 providing and fixing cp brassover head shower with 15 or 20 mm inlet including connection complete: 100mm diameter. 42 providing and fixing trap of selfcleansing design with screwed down or hinged grating with or with out vent arm complete, including cost of cutting chases and making good the walls and floors:100mm inlet and 100mm out let pvc 43 100mm inlet and 75mm outlet pvc 44 providing and placing on terrace (at all floor levels) polyethylene water storage tank, isi : 12701 marked, with cover and suitable locking arrangement andmaking necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 45 providing, fixing and jointing pvc pipes of different diameters with with pvc solvent cement (or as per manufacturers specifications) with or without sockets (if sockets are provided with pipe length) in vertical sewage line, waste water line and vent line with all necessary bends, angle bends, tees, elbows ms bat clamps along with all necessary fastners and bolt with cutting chases and making good the walls and floors wherever required including testing of the same all as per direction and satisfaction of engineer in charge.6kg per sqin pressure pipe75mm inner dia. 46 6kg per sqin pressure pipe110mm inner dia. 47 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, including fixing the pipe with clamps 1.00m spacing. this includes jointing the pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. 15mm nominal outer dia pipes. 48 25mm nominal outer dia pipes. 49 constructing masonary chamber 30x30x50cminside,inbrick workincementmortar1:4(1 cement:4coarsesand),with ci surface box 100x100x75 mm(inside)withhingecover fixed in cement concrete slab 1:2:4 ( 1 cement : 2 coarse sand:4 graded stone aggregate 20mm nominal size) including necessary excavation, foundationconcrete1:5:10(1cement:5finesand:10graded stoneaggregate40mmnominal size)andinsideplasteringwith cement mortar1:3 ( 1 cement : 3coarsesand)12mmthick, finishedwithafloatingcoatof neat cement complete as perstandard design: 50 supply delivery errection the fabricatedmsboardofsuitable sizeonwhichthefollowing supplieditemsshallbefixedas per the direction of enggincharge. 51 (a)supply and fixing 63 ampdoublepole(singlephase &neutral)240voltresidual currentcircuitbreakerrccb havingasensivitycurrentup to300 ma on the existing ms board complete with connection testing&commissioningetcas required. 52 (b)supplying & fixing 2+8way single door prewired sp&n mcb distribution board of sheet steel for240voltonexistingms board complete with dpmcb isolator40amp240volt1no& 25amp single pole240 volt spmcb(c)series5nos completeduly wired with 4sqmm fr pvc insulated copper conductorupto terminal box tinned copper busbar ditachable gland plate, inter connection phosphotized &powder coated includingearthingetcasreq( for power distribution ) 53 (c)supplying & fixing 2+8way single door prewired sp&n mcb distribution board of sheet steel for240voltonexistingms board complete with dpmcb isolator40amp240volt1no& 10amp single pole240 volt spmcb(c)series5nos completeduly wired with 4sqmm fr pvc insulated copper conductorupto terminal box tinned copper busbar ditachable gland plate, inter connection phosphotized &powder coated includingearthingetcasreq( for light distribution ) 54 wiring point for lightwith 1.5sq mmfrpvcinsulated multistrandsinglecorecopper conductorcableinpvcconduit concealedinthewallcomplete with modulartype switch &ceilingrose/angle/batten holderon3mmthickphenolic laminated backalite sheet etc comp in all respect 55 wiringpointforfan 1.5sq mmfrpvcinsulated multistrandsinglecorecopper conductorcableinpvcconduit concealedinthewallcomplete with modulartype switch &ceiling roseon3mmthick phenolic laminated backalite sheet &fan boxetccompin all respect 56 wiringpointfor freshairfan with 1.5sq mmfrpvc insulated multistrandsinglecorecopper conductorcableinpvcconduit concealedinthewallcomplete with modulartype switch &ceiling roseon3mmthick phenolic laminated backalite sheetetc comp in all respect 57 supply&fixing5ampmodular switch & 5amp 5pin modular socketontheexistingmodular plateandswitchboxincluding connection etc as reqd. 58 supply&fixingofpowerplug 20amp250voltflushtype modular switch& 5pin 20amp 250voltmodular socket on concealedmsbox etc.asrequered 59 supply & wiring for power pointwith2no4sqmmfrpvc insulated1100voltgrade multistrandsinglecorecopper conductor cable in 20mm dia heavydutypvcconduitwith1 no2.5sqmmfrpvcinsulated multistrandcopperconductor cable as earth continuity wire in conduit etc as required 60 wiringofcircuitalongwith earth wire with the following size of fr pvc insutated copper conductorsinglecorecablein recessed medium class 20mm dia pvc conduit as required 61 1x1.5sqmm+1x1.5sqmm 62 supply & fixing of electronic fan regulatormodular400w 120v-- 280v isi marked on existing switchboard includingmaking connection etc for proper completion of work 63 supply&burryingofsafe earthingelectrodet-19zn-zinc coated,lengthupto3000mm, outer pipe 48.4mmx3.2mm, inner pipe 26.9mmx2.6mm, terminaldia12mm,coating80- 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc)capable of reducingthe soilresistivitywith good mixture of retaining capacityandoneearthinglead of 20mmx3mmg.i. strip,up to switch board (from apron to switchboard,thecostofg.i. strip will be extra)along with 30cm square c.i. frame with hinged cover & masonary housing 64 supplying&layingof 20mmx3mm g.i. strip directly in ground&onwallasrequired complete in all respect (from apron to switch board. 65 wiring for submain withthe 2x10sqmm size fr pvc insulated copper conductor cable in recessedmediumclasspvcconduit as required 66 boring with hydraulic piling rigs with power units, providing and installingcastinsitusingleunder reamedpilesofspecifieddiameter andlengthbelowpilecapinm-25 cementconcrete,tocarryasafe working load not less than specified, excluding the cost of steel reinforcement but including thecostofboringwithbentonite solutionandthelengthofthepile to be embedded in pile cap etc. all complete.(lengthofpilefor payment shall be measured upto tothe bottom of pile cap) : 300 mm dia piles 67 s/f of kitchen sink including all labour and t&p all complete. 68 15mm thick plaster in 1:4 (1 cement and 4 coarse sand) including all labour complete. 69 s/f of gate valve including all labour and t&p all complete 70 s/f pvc bulb holder including all labour and t&p all complete 71 s/f aluminium door handle including all labour and t&p all complete 72 s/f of chequered tiles on ramp of house including all labour and t&p all complete 73 s/f flange bib cock with z spray including all labour and t&p all complete 74 s/f of kota stone on rear court yard anf front porch of house including all labour and t&p all complete 75 s/f of granite stone on kitchen top of house including all labour and t&p all complete 76 s/f of basin mixture including all labour and t&p all complete 77 s/f of 25mm cpvc pipe including all labour and t&p all complete

Government Departments

TRN :49022869 | 12 May, 2025

Tender Value : 1.60 Lacs

Pinjore - Haryana

Tender for tender for supply and installation of various items/goods at frh and ota in forest complex pinjore; 1 kent excell+ (r.o.) ? product code : 111003 ? product colour: white ? net weight : 10.70 kg ? dimensions(mm) :390(l)x200 (w)x520 (h) ? total power consumption : 60 w 1 2 voltas visi cooler 450 litres single door ? model no.: 5410719 / vc 450 ? gross volume: 450 l ? product dimension(wxdxh): 650 x 730 x 1900 ? temperature range: 0°c to 10°c ? soft aesthetic design ? wheels for easy mobility ? upto 40% energy efficient compressor ? self asthetic design ? energy efficient compressor ? anti-corrosive pre-coated body 1 3 havells monza ec 5s 10-litre storage water heater with flexi pipe ? capacity: 10 litres; ? wattage: 2000 watts; ? pressure: 8 bars ; ? bee rating: 4 star; ? waterproof degree : ipx-4 protection for longer product life 4 sujata gas stove ? 8mm ultra -thick toughened glass designed for long -lasting durability, added safety, and a premium look to enhance kitchen?s style. ? warranty: 9 years warranty on complete products including toughened glass. ? italian sabaf gas valve for longer life & easy conversion from lpg to png ? rigid, stable and sturdy pan supports with flame guard for gas saving ergonomically designed alloy knob5g designed forged brass burner with direct flame for indian style cooking ? titanium finish (black ss) drip tray ? 360° rotating brass gas nozzle for easy connection from any direction aesthetically ultra sleek design isi -certified product ? combination of 1 jumbo, 2 big, and 1 small burner for convenient cooking extra pair of jet to convert from lpg to png 1 . 5 sujata dynamix 900 watts mixer grinder ? colour : white 2 ? product dimensions 25dx60wx35h cms. ? blade material: stainless steel ? special feature compact ? capacity 1.5 cubic inches ? item weight 6000 grams 6 faber 90cm 1500m³/hr bldc motor autoclean slant chimney ? type: slant glass, wall mounted, bldc motor | black finish with 1500 m3/hr suction capacity ? control type: 9 speed touch & gesture | power: 240w ? led lights: 2 led rectangle lights ? finish: filterless matt black finish with black powder coated oil collector ? features: 80w bldc motor| noise reduction | toughened black glass and 1 metal blower ? 12 yrs on motor, 5 yrs comprehensive warranty by faber

State Government

TRN :49023607 | 16 May, 2025

Tender Value : 22.62 Lacs

Lucknow - Uttar Pradesh

Tender for tender for construction and renovation work of community center located in sector-d of kanpur road scheme - rcc repairs 2 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge. 3 75mm average thickness 4 50mm average thickness 5 25 mm average thickness 6 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 7 bars upto 12 mm diameter 8 bars above 12 mm diameter 9 drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in rcc beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer-in-charge.upto and including 12mm dia. 10 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect.epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 11 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge.note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 12 25 mm average thickness in 2 layers. 13 50 mm average thickness in 3 layers. 14 providing and laying sbr polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structuralmembers e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of rcc member.note: rates shall be for finished surface area of concrete and shall include the cost of making holes in existing rcc slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved super-plasticiser forrendering concrete as flowable self compacting and sbr polymer but shall exclude cost of reinforcement, bond coat, shear keys, centering and shuttering, strutting, propping etc (payment under this item shall be madeonly after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) 15 50mm thick in grade m 25 with cement content not less than 330 kg per cum 16 75mm thick in grade m 25 with cement content not less than 330 kg per cum 17 100mm thick in grade m 25 with cement content not less than 330 kg per cum 18 providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge.(the payment shall be made on the basis of actual weight of approved grout injected.) 19 epoxy injection grout in concrete/rcc work of approved make 20 providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the engineerin- charge.wooven pvc cloth 21 shotcreting r.c.c. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stoneaggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by engineer- in-chargenote: rates shall include the providing necessary ground wires etc. the levelling gauges, if used, shall be paid for separately. payment under this item shall be made only after proper wet curing has been done and surface hasbeen satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 22 50mm thick in grade m 25 with cement content not less than 330 kg per cum 23 75mm thick in grade m 25 with cement content not less than 330 kg per cum 24 providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of engineer-in-charge. 25 providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 26 mild steel or iron work in plain work such as in r.c.c. or r.b. (when not included in an over all rates ) including bending for proper completion of the workand including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. 27 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 28 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 29 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thic 30 waterproofing and terracing 31 providing and laying in situ five course water proofing treatment with app (atactic polypropylene) modified polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to is : 702, 3rd layer of roofing membrane app modified polymeric membrane 2.0 mm thick of 3.00 kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron hmhdpe film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron hmhdpe film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 33 miscellaneous works 34 providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, includingadditional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia m.s. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with m.s. tubes, m.s. tube challis, m.s. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of engineer-in-charge.note:- (1) the elevational area of the scaffolding shall be measured for payment purpose. (2) the payment will be made once only for execution of all items for such works. 35 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. 36 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 37 cleaning of under ground sump, over head r.c.c. tank ( independent staging) including disposal of slit and rubbish, all as per direction of engineer-in-charge.the cleaning shall consist following operations:-(i) tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits.(ii) entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water.(iii) chlorination of rcc internal surface by liquid chlorine.(iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.(v) finally the surface shall be treated with ultraviolet radiation etc. as per direction of engineer-in-charge. 38 door-window repair 39 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) 40 renewal of old putty of glass panes (length) 41 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead asper direction of engineer - in- charge. 42 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer-in-charge. 43 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar 44 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres 45 casement door double panel with french (false) mullion with zinc alloy (zamak) 3d hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.using r4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above ) x (100 mm& above) & french (false ) mullion (64mm & above) x (60 mm & above). (height above 2.5 metre) 46 toughened glass 12 mm thickness 47 finishing work 48 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 49 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 50 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 51 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 52 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 53 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 54 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 55 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 56 washrooms 57 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 58 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 59 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including isi marked stainless steel butt hinges with necessary screws 60 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 61 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 62 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Government Departments

TRN :49024029 | 21 May, 2025

Tender Value : 30.30 Lacs

Pratapgarh - Uttar Pradesh

Tender for tender for link road chamir saraiya se pure rammu tak road construction work - earthwork in cutting or embankment /pattri in ordinary soil (loam, clay or sand) excavation to be done in the from of regular pits not exeeding 0.50m in depth and earthwork in embankment to be in 20cm layers including the ramming and dressing the surface to required levles and slopes and also including 1.50meter lift and 1000meter lead as directed by e/i including labour t&p etc required for proper completion of work (as per si no-253) 2 gsb- gramular sub-base with well graded material (table 400,1) a) by mix in place method contrcution of granular sub-base by providing well graded material spreading in unform layers with motor grader/tractor mounted appropriate equipment on prepaire suface maxing by mix in place method with rotavator at omc, and compacting with smooth roller to achieve the desired density, complete as per clause 401 3 wbm g-2 (inter coat)providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening /binding materials to fill-up the interstices of coarse aggregate watering and compacting to the required dencity grading -2 as per technical specification clause 405 4 wbm g-3 - providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening to fill-up the interstices of coarse aggregate watering and compacting to the required dencity as per technical specification clause 405 5 excavation in foundation in ordinary soil 6 concrete in 1:6:12 in foundation 7 m 150 class brick work in 1:4 in foundation up to plinth 8 5 cm thick c.c thick cement concrete with all complete work 9 wbm g-3 - providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening to fill-up the interstices of coarse aggregate watering and compacting to the required dencity as per technical specification clause 405 10 providing and laying of rubber moulded reflective zig-zag 80mm thick tiles of precast compressed c.c passing minimum 30mpa compressive strength isi marked concrete block pavements having thickness 80mm as per technical specaification clause 1504 11 brick edging on both sides of metalled surface 12 cm deep & 8 cm wide with class m-150 bricks laid on edge and dry in proper grade and alignment including cost of all material, labour and t&p etc.complete and all taxes as per direction of e/i. 12 providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.75 kg / sqm using mechanical means. as per technical specification clause 502 including cost of bitumen emulsion (ss-1) 13 providing and applying tack coat with bitumen (vg-10)using bitumen pressure distributor at the rate of 0.35kg per sqm on the prepared bituminous surfacecleaned with hydraulic broom as per technical speicification clause 503 including cost of bitumen (vg-10) 14 providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line grade and level to serve as wearing coarse on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kn static roller capacity finished to required lavel and grades to be followed by seal coat as per techincal specification clause 508 including cost of bitumen 15 providing and applying seal coat type c comprising of a layer of bituminous binder followed by a cover of stone chipping of specified grading and rolling with power roller 8-10 tonne kn static roller and finishing to required level and grades as per technical specification clause 510 including cost of bitumen 16 s/f of 350 mm dia hume pipe 17 s/f of reflectivesign board,etc 18 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for1 st year maintenance cost @ 0.0 % 19 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for2nd year maintenance cost @ 0.75 % 20 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for3rd year maintenance cost @ 1.50 % 21 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for4thyear maintenance cost @ 2.25 % 22 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for5thyear maintenance cost @ 3.00 % 23 the routing maintenance of above road including earthen shoulder and interlocking road etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for 1styear maintenance cost @ 0.00 % 24 the routing maintenance of above road including earthen shoulder andinterlocking road etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for 2ndyear maintenance cost @ 0.25 % 25 the routing maintenance of above road including earthen shoulder andinterlocking road etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for 3rdyear maintenance cost @ 0.50 % 26 the routing maintenance of above road including earthen shoulder and interlocking road etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for 4rdyear maintenance cost @ 0.75 % 27 the routing maintenance of above road including earthen shoulder and interlocking road etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for 5thyear maintenance cost @ 1.00 %

Government Departments

TRN :49024051 | 21 May, 2025

Tender Value : 80.09 Lacs

Allahabad - Uttar Pradesh

Tender for tender for link road kithawar market to basti hote hue primary school tak road construction work - earthwork in cutting or embankment /pattri in ordinary soil (loam, clay or sand) excavation to be done in the from of regular pits not exeeding 0.50m in depth and earthwork in embankment to be in 20cm layers including the ramming and dressing the surface to required levles and slopes and also including 1.50meter lift and 1000meter lead as directed by e/i including labour t&p etc required for proper completion of work (as per si no-253) 2 gsb- gramular sub-base with well graded material (table 400,1) a) by mix in place method contrcution of granular sub-base by providing well graded material spreading in unform layers with motor grader/tractor mounted appropriate equipment on prepaire suface maxing by mix in place method with rotavator at omc, and compacting with smooth roller to achieve the desired density, complete as per clause 401 3 wbm g-2 (inter coat)providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening /binding materials to fill-up the interstices of coarse aggregate watering and compacting to the required dencity grading -2 as per technical specification clause 405 4 wbm g-3 - providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening to fill-up the interstices of coarse aggregate watering and compacting to the required dencity as per technical specification clause 405 5 brick edging on both sides of metalled surface 12 cm deep & 8 cm wide with class m-150 bricks laid on edge and dry in proper grade and alignment including cost of all material, labour and t&p etc.complete and all taxes as per direction of e/i. 6 excavation in foundation in ordinary soil 7 concrete in 1:6:12 in foundation 8 providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.75 kg / sqm using mechanical means. as per technical specification clause 502 including cost of bitumen emulsion (ss-1) 9 providing and applying tack coat with bitumen (vg-10)using bitumen pressure distributor at the rate of 0.35kg per sqm on the prepared bituminous surfacecleaned with hydraulic broom as per technical speicification clause 503 including cost of bitumen (vg-10) 10 providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line grade and level to serve as wearing coarse on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kn static roller capacity finished to required lavel and grades to be followed by seal coat as per techincal specification clause 508 including cost of bitumen 11 providing and applying seal coat type c comprising of a layer of bituminous binder followed by a cover of stone chipping of specified grading and rolling with power roller 8-10 tonne kn static roller and finishing to required level and grades as per technical specification clause 510 including cost of bitumen 12 s/f of 350 mm dia hume pipe 13 s/f of reflectivesign board,etc 14 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for1 st year maintenance cost @ 0.0 % 15 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for2nd year maintenance cost @ 0.75 % 16 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for3rd year maintenance cost @ 1.50 % 17 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for4thyear maintenance cost @ 2.25 % 18 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for5thyear maintenance cost @ 3.00 %

Government Departments

TRN :49024100 | 21 May, 2025

Tender Value : 48.96 Lacs

Pratapgarh - Uttar Pradesh

Tender for tender for link road sadwa chandika ke gram sabha chatarpur khanderi to raghna hote hue mishran tak road construction work - earthwork in cutting or embankment /pattri in ordinary soil (loam, clay or sand) excavation to be done in the from of regular pits not exeeding 0.50m in depth and earthwork in embankment to be in 20cm layers including the ramming and dressing the surface to required levles and slopes and also including 1.50meter lift and 1000meter lead as directed by e/i including labour t&p etc required for proper completion of work (as per si no-253) 2 gsb- gramular sub-base with well graded material (table 400,1) a) by mix in place method contrcution of granular sub-base by providing well graded material spreading in unform layers with motor grader/tractor mounted appropriate equipment on prepaire suface maxing by mix in place method with rotavator at omc, and compacting with smooth roller to achieve the desired density, complete as per clause 401 3 wbm g-2 (inter coat)providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening /binding materials to fill-up the interstices of coarse aggregate watering and compacting to the required dencity grading -2 as per technical specification clause 405 4 wbm g-3 - providing and laying spreading and compacting stone aggregates of specific sizes to water bound macadam specification incluidng spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber applying and brooming stone screening to fill-up the interstices of coarse aggregate watering and compacting to the required dencity as per technical specification clause 405 5 brick edging on both sides of metalled surface 12 cm deep & 8 cm wide with class m-150 bricks laid on edge and dry in proper grade and alignment including cost of all material, labour and t&p etc.complete and all taxes as per direction of e/i. 6 providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.75 kg / sqm using mechanical means. as per technical specification clause 502 including cost of bitumen emulsion (ss-1) 7 providing and applying tack coat with bitumen (vg-10)using bitumen pressure distributor at the rate of 0.35kg per sqm on the prepared bituminous surfacecleaned with hydraulic broom as per technical speicification clause 503 including cost of bitumen (vg-10) 8 providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line grade and level to serve as wearing coarse on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kn static roller capacity finished to required lavel and grades to be followed by seal coat as per techincal specification clause 508 including cost of bitumen 9 providing and applying seal coat type c comprising of a layer of bituminous binder followed by a cover of stone chipping of specified grading and rolling with power roller 8-10 tonne kn static roller and finishing to required level and grades as per technical specification clause 510 including cost of bitumen 10 s/f of 350 mm dia hume pipe 11 s/f of reflectivesign board,etc 12 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for1 st year maintenance cost @ 0.0 % 13 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for2nd year maintenance cost @ 0.75 % 14 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for3rd year maintenance cost @ 1.50 % 15 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for4thyear maintenance cost @ 2.25 % 16 the routing maintenance of above road including earthen shoulder and bitumenous pavement etc of to the required standards and it the manner as defined in cb condition and keep the entire road surfaceand structure in defect free condition during the entire maintenace period which begins from the actual completion data and ends after five years (including cost of material t&p labour but excluding gst) for5thyear maintenance cost @ 3.00 %

Government Departments

TRN :49026423 | 01 Jan, 0001

Tender Value : 0

Hazira - Gujarat

Tender for tender for structure dismentaling work at pwh_crm1 2000167357 10 10 10 dismantling of structure 200 to email : hitesh.prajapati@amns.in contact : name : hitesh prajapati item details : * scope of work for vendor: -dismantling existing structures as per requirement. -tools, tackles, grinding m/c etc. -supply of manpower with proper ppes -welding m/c, cutting set, cylinders. -consumables like welding electrodes, grinding wheels. -supervisor in contractor scope -job to be done as per instructions by line in-charge only. * scope of work- amns:- - essentials like electricity, water etc. - crane and hydra will be provided if required. - scaffolding or man lifter will be provided if required. - vehicle will be provided for scrap loading and disposal work. - specific penalty for safety violation and non-performance by vendor. specific penalty for nonperformance by vendor and must be cardinally measured. amns safety rule and regulation as per company policy: • all the persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(cnh). • all the workers have authorized work at height valid pass. • work should be started only after taking authorized work permit. • toolbox talk must be delivery before starting the job on daily basic. • use certified portable hand electric machine. • use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • the person who is working at height should wear certified double lanyard full body harness (safety belt) <(>&<)> locked safety belt (both clamp) with lifeline. anchoring point must be check before every use. • use only certified two lanyards connected in a y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • ensure that all persons are wearing safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / for job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • work should be carried out in close supervision of competent supervisor. • the working at height job should be allowed in daytime only • while handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • while fabrication activity ensure crane movement. crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from page 2 of 2 arcelormittal nippon steel india pvt ltd am/ns hazira plant 27th km, surat-hazira road,,hazira,394270,gujarat,india gstin 24aaace1741p1zn pan aaace1741p cin u27100gj1976ftc013787 request for quotation number 6000133471 date 05.05.2025 submission date 13.05.2025 coll req no amns deals with oems directly. we are very well equipped in every way to import / buy our goods directly from oems from any part of the world in a professional manner. we also use the vast global networks of our parent companies where necessary. we do not welcome any contact from intermediaries or indian agents of vendors. we assure all oems that you do not need to engage anyone to manage your transactions with us.kindly respond to our rfqs and deal with our officials directly without involving any agents or intermediaries. offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. contact for this rfq mr. venkat sai taneeru contact email venkat.taneeru@amns.in materials / services please acknowledge receipt of the rfq and provide your best quote for below given rfq details. sr. no pr no. pr item rfq item services for line item quantity uom technical details other details working area. • while fabrication activity near dsl side, ensure dsl power supply must be cut off <(>&<)> for that lototo must be taken for isolation of dsl power supply. • while fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • while scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • the working area need to be cleaned to avoid the slipping hazards. • ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • always carry fe near workplace. • never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • ensure loose cylinder should not be kept at shop floor. • no oxygen or acetylene gas shall be used for pressure testing purpose. • no oxygen or acetylene gas shall be used for cleaning purposes. • always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. sop no:- amnsil/crm/pwh/19/sop/05 hirac no:- amnsil/crm/pwh/16.7/hirac/39

Government Departments

TRN :49027850 | 21 May, 2025

Tender Value : 8.40 Lacs

Agra - Uttar Pradesh

Tender for tender for road work by hotmix in zone-1 chhata room no.68 noorie darwaza lady loyal hospital. - dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre, as per direction of engineer-in-charge. 2 supplying and stacking at site 53 mm to 22.4 mm size stone aggregate 3 supplying and stacking at site stone dust 4 preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 5 surface dressing one coat on old surface with bitumen of specified grade at the rate of 1.22 kg/ sqm of surface area with 1.10 cum of stone chippings 11.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity etc. complete: using bitumen emulsion (minimum 50% bitumen content- rs grade conforming to is : 8887) 6 providing and applying tack coat using bitumen emulsion conforming to is:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanicalbroomon bituminous surface @ 0.25kg/sqm 7 providing and laying dense graded bituminous macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of engineer-in-charge.50 to 100 mm average compacted thickness with bitumen of grade vg-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) prepared in batch type hot mix plant of 100-120 tph capacity 8 providing and laying bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of engineer-in-charge. 40/50 mm compacted thickness with bitumen of grade vg-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of aggregate) prepared in batch type hot mix plant of 100-120 tph capacity 9 sub total 10 add/deduction rs. for estimate figure amount match 11 grand total

Related Searched Keywords : power press

List of power-press Tenders

Get power press Tender Alert...

Related Searched Keywords : power press

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us