Filters

List of silicon-gel Tenders

List of latest silicon-gel Tenders in Indian Tenders. Click on any silicon-gel Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for silicon-gel Tenders.

All-Tenders (8)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Central Government/Public Sector

TRN :49054084 | 10 Jun, 2025

Tender Value : 28.00 Crore

Abohar - Punjab

Tender for tender for provision of deficient married accommodation at fazilka mil stn (job no: - mwp/swc-02/2024-25); 1 lump sum price worked out by the tenderer for“building /structure works as listed in schedule ‘a’ section - i 2 sch a section- ii, internal electrification works and flame proof fittings 3 material and labour for concealed point wiring for one light point/fan point controlled by one switch (using red, black and green colour wires as colour coding) complete with 2.5 sqmm (nominal cross section area)single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt (isi marked)drawn through andincludingpvc conduit 20mm dia (medium duty, isi marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including pressed steel powder coated sunken terminal box suitable for modular switch socket (min 50mm deep and 1.6mm thick sheet, suitable size) concealed in wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/ socket / regulator etc, including provn of 2.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using cm (1:3)including fixing ofswitch/socket/regulator etc complete all as specified and as directed. (switch, socket, regulator shall be measured and paid separately under appropriate item of boq as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ). 4 -do- all as per srl no. 3 above but one three pin switch socket outlet 5 amps on the same borad 5 -do- all as per srl no. 3 above but one call bell controlled by one bell switch 6 -do- all as per srl no. 3 above but wiring with 2.5 sqmm multistranded cable and earth wire with copper conductor of size 2,5 sqmm for 5 amps point (on independent board) 7 material and labour for concealed point wiring for one socket outlet 15/20 amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 4 sqmm (nominal cross section area)single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt (isi marked)drawn through andincludingpvc conduit 25mm dia (medium duty, isi marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including pressed steel powder coated sunken terminal box suitable for modular switch socket (min 50mm deep and 1.6mm thick sheet, suitable size ) concealed in wall, including inner and outer plates (cover plate) suitable for fixing the modular switches / socket, including provn of 4 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using cm(1:3), including fixing ofswitch, socket complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of boq as supply only but cost of moudlar cover plate with frame and labour for fixing the same shall deemed to be included in the unit rate). 8 supply only modular switch 6amps, piano flush type, single pole, one way (1 module) complete all as specified and as directed by engineer-in-charge (laminated sheet top cover is included in point wiring). 9 supply only modular switch 16amps,piano flush type, single pole, one way (1 module) complete all as specified and as directed by engineer-in-charge (laminated sheet top cover is included in point wiring). 10 supply only modularsocket outlet 2 in 1, 6amps,flush type fixed on laminated sheet top cover complete all as specified and as directed by engineer-in-charge (laminated sheet top cover is included in point wiring). 11 supply only modularsocket outlet 5 in 1, 16amps,flush type fixed on laminated sheet top cover complete all as specified and as directed by engineer-in-charge (laminated sheet top cover is included in point wiring). 12 supply and fixing ceiling rose, polycarbonate, isolated body, surface bakelite 2 to 3 terminal, 240 volts, 5/6 amp, isi marked complete all as specified and as directed by engineer-in-charge. 13 supply and fixingelectric calling bell ding dong type, ac 230 volts single pole including making elctric connection complete all as specified and as directed by engr-in-charge. 14 supply only modular bell push switch, piano flush type, 6amps, single pole, one way (1 module) fixed on laminated sheet top cover (laminated sheet top cover is included in point wiring) complete all as specified and as directed by engineer-in-charge. 15 supply and hanging /fixing ceiling fan 1200 mm sweep ac supply (input voltage range ; 120 to280v), bldc type, 5 star rated, bee and isi marked super enamelled, copper winding of b class insulation, single phase, maximum 30w (± 10%), temperature rise 40 degree maximum without remote with and including capacitive regulator, 03 no blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable sizefrom ceiling rose to fan complete all as specified and as directed by engr-in-charge.note :- (i) serial number as issued by engr-in-charge of celing fan and ge office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account 16 supply and fixing exhaust fan (heavy duty) steel body, ac single phase 230v, 50hz, 900rpm, size 300mm sweep with blades and frame including new mosquito stainless steel wire mesh of guage 0.36mm with suitable wooden frame protection against birds etc mounted in suitable opening arrangement in wall and electric connection with and including three core pvc insulated pvc sheathed copper conductor flexible cable 24/0.2mm drawn in flexible pvc conduit and hanging on wall with 4 nos steel fastners 12mm dia 200mm long and making good the disturbed surface complete all as specified and as directed by engineer-in-charge.note :- (i) serial number as issued by engr-in-charge of fan and ge office name shall also be written on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account (ii) cost for making suitable cutting/opening in wall for fixing of exhaust fan including making good disturbed surface and masonary work shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 17 supply and fixed for spn 8 way, 240 volt distribution board door made out of crca mild steel sheet surface with insulated material like polyester or with powder coating surface mounting with bus bar rating 200 amps, dust and vermin proof, ip-43 protected, suitable for incorporation of mcbs and isolators etc complete all as specified and as directed by engineer-in-charge. 18 supply and fixed for spn 6 way, 240 volt distribution board door made out of crca mild steel sheet surface with insulated material like polyester or with powder coating surface mounting with bus bar rating 200 amps, dust and vermin proof, ip-43 protected, suitable for incorporation of mcbs and isolators etc complete all as specified and as directed by engineer-in-charge. 19 supply and fixed for spn 4 way, 240 volt distribution board door made out of crca mild steel sheet surface with insulated material like polyester or with powder coating surface mounting with bus bar rating 200 amps, dust and vermin proof, ip-43 protected, suitable for incorporation of mcbs and isolators etc complete all as specified and as directed by engineer-in-charge. 20 supply and fixed for tpn distribution board 4 way vertical type double door made out of crca mild steel sheet surface with insulated material like polyester or with powder coating flush/surface mounting with copper bus bar suitable rating with neutral bar and earth bar and cable tie for cable management, ip-54 protection and provision and including mccb 4 pole 160 amp, 16 ka as incomer and mcbs as outgoing, dust and vermin proof complete all as specified and as directed by engineer-in-charge. 21 supply and fixed of mcb suitable for 240 volts ac supply, spn with over load and short circuit protection and rupturing capacity not less than 10 ka, c curve as 6 to 32 amps complete all as specified and as directed by engineer-in-charge. 22 supply and fixed of mcb suitable for 240 volts ac supply, spn with over load and short circuit protection and rupturing capacity not less than 10 ka, b curve as 40 amps complete all as specified and as directed by engineer-in-charge. 23 supply and fixed of mcb suitable for 240 volts ac supply, spn with over load and short circuit protection and rupturing capacity not less than 10 ka, b curve as 6 to 32 amps complete all as specified and as directed by engineer-in-charge. 24 supply and fixing blanking plate of plastic suitable for any type of db complete all as specified and as directed by engineer-in-charge. 25 material and labour for submain wiring comprising single core, 2 runs of 4.0 sqmm nominal cross sectional area multi stranded frls copper conductor cable, pvc insulated unsheathed 1100 volts grade drawing in and including pvc conduit of size min 20mm dia isi marked and its fittings concealed in floor/roof / wall complete including provision of 01x4.0 sqmm nominal cross sectional area multi stranded frls copper conductor cable, pvc insulated unsheathed 1100 volts grade as earth wire and using color code as per is complete all as specified and as directed by engineer-in-charge. note : meter of pipe including fitting and 3 runs of single core cable shall be measured as unit runing meter. additional wire/cable required for connecting to mcb shall be included in overall cost quoted. 26 material and labour for submain wiring comprising single core, 2 runs of 6.0 sqmm nominal cross sectional area multi stranded frls copper conductor cable, pvc insulated unsheathed 1100 volts grade drawing in and including pvc conduit of size min 25mm dia isi marked and its fittings concealed in floor/roof / wall complete including provision of 01x6.0 sqmm nominal cross sectional area multi stranded frls copper conductor cable, pvc insulated unsheathed 1100 volts grade as earth wire and using color code as per is complete all as specified and as directed by engineer-in-charge. note : meter of pipe including fitting and 3 runs of single core cable shall be measured as unit runing meter. additional wire/cable required for connecting to mcb shall be included in overall cost quoted. 27 material and labour for submain wiring comprising single core, 2 runs of 10.0 sqmm nominal cross sectional area multi stranded frls copper conductor cable, pvc insulated unsheathed 1100 volts grade drawing in and including pvc conduit of size min 25mm dia isi marked and its fittings concealed in floor/roof / wall complete including provision of 01x6.0 sqmm nominal cross sectional area multi stranded frls copper conductor cable, pvc insulated unsheathed 1100 volts grade as earth wire and using color code as per is complete all as specified and as directed by engineer-in-charge. note : meter of pipe including fitting and 3 runs of single core cable shall be measured as unit runing meter. additional wire/cable required for connecting to mcb shall be included in overall cost quoted. 28 material and labour for earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including giearthing wire of size 4 mm dia by means of gi bolts/nuts/washers and protected by 15 mm bore gi light grade pipe upto test point or upto main switch board, ht/lt equipments, fixing with 02 nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore gi medium grade pipe for watering and including funnel, wire mesh, pcc chamber pit made with pcc (1:3:6) type c1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m,pit cover 40mm thick made with rcc (1:2:4) type b1 (using 20 mm graded stone aggregate) including tmt reinforcement 8mm dia @ 75mm c/c both way, ms handle 12mm dia, cover rest on ms angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate no. 3 ofssr 2009 (part-i) complete all as specified and as directed by engineer-in-charge.note:- (i) pcc chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) protection pipe and gi earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) the earth testing arrangement should be done by the contractor as per direction of engineer-in-charge. 29 supply and fixing led tube light fitting polycarbonate housing 1 x 18/20watt, appx 4 feet long, with decorative box linear, housing environment friendly, including electric connection with using 2 core flexible copper conductor cable of size 01 sqmm from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by engineer-in-charge :- (a) lumen system efficacy of luminaire should be minimum 100 lumen per watt.(b) input voltage range : 140 to 270 volts.(c) temp operating range : minus 10°c to plus 45°c(d) power factor : minimum 0.95 (e) thd : current thd max10% and voltage thd max 5%(f) ip rating : ip-20.(g) aluminium housing & integrated electronic driver(h)led driver of the same make as of the luminaire.(j) led driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) surge protection minimum 2.5 kv. (l) cct : minimum 6500k(m) cri : more than 80 (n) rated life time : 50000 burning hrs @l70 (average 10 to 12 hrs daily) 30 supply and fixing led tube light fitting polycarbonate housing 1 x 10watt, appx 2 feet long, with decorative box linear, housing environment friendly, including electric connection with using 2 core flexible copper conductor cable of size 01 sqmm from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by engineer-in-charge :- (a) lumen system efficacy of luminaire should be minimum 100 lumen per watt.(b) input voltage range : 140 to 270 volts.(c) temp operating range : minus 10°c to plus 45°c(d) power factor : minimum 0.95 (e) thd : current thd max10% and voltage thd max 5%(f) ip rating : ip-20.(g)led driver of the same make as of the luminaire.(h) led driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(j) surge protection minimum 2.5 kv. (k) cct : minimum 6500k(l) cri : more than 80 (m) rated life time : 50000 burning hrs @l70 (average 10 to 12 hrs daily) 31 supply and fixing led lamp 1x9 watt including pvc holder with complete suitable for fixation on wall/roof with body robust corrosion resistant, superior flnish and without any cracks of through holes complete all as specified and directed by engineer-in-charge 32 supply and fixing energy efficient led security light fitting of 35w pressure die cast aluminium housing/body, heat resistant clear toughened glass,better optics for uniform distribution street/roadway luminaire, with driver, including electric connection with using 3 core flexible copper conductor cable 1.5sqmm from ceiling rose to light fitting, fixing the light fitting with new bracket made out of gi tubing medium grade 32mm dia, 1.2 metre long bent to shape at 32 degree angle at half metre from bottom, including two nos clamps made out of ms flat iron size 25x3 mm with suitable nuts and bolts for fixing of bracket including painting to ms clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, complete all as specified and directed by engineer-in-charge :- (a) lumen system efficacy of luminaire should be minimum 100 lumen per watt.(b) input voltage range : 140 to 270 volts (c) temp operating range : minus 10°c to plus 50°c (d) power factor : minimum 0.95(e) thd : max10%.(f) ip rating : ip66. (g) ik rating:minimum ik07 (h) built in potted led driver of the make as of the luminaire.(j) led driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) surge protection 10 kv (inbuilt + extended) (l) cct : 5700 k. (m) cri: more than 80 (n) lens - high efficiency wide angle lens. (o) bis approved fixtures and driver (p) rated life time : 50000 burning hrs @l70 (average 10 to 12 hrs daily) 33 rigid non metallic pvc conduit 20mm dia (external) for sub main/telephone wiring inclusive of all fittings such as tees, bends, elbow, reducers, junction boxes bell mouth tube ends and all fixing accessories such as couples, bolts, nuts, saddles, pipe hooks etc complete all as specified and as directed by engineer-in-charge. 34 material and labour for mild steel boxflush mounted of size 100mm x100mmx100mm having holes for 20 mm conduit entry including 02 pin tv socket outlet flush type marked with symbol of tv and 03 mm thick plastic laminated sheeet cover and making good disturbed surfaces of walls by using cm (1:3)complete all as specified and as directed by engineer-in-charge 35 supply, installing, commissioning and testing of electric water heater (geyser) storage type abs body of capacity 25 litres, bee approved 5 star rating, 230 v , single phase, ac supply, inner tank made out of heavy duty stainless steel sheet (designed with single weld line, factory tested with hydraulic pressure as per latest is code) with glass lined coating complete with all accessories such as safety valve, thermostate, nrv, connection piece pvc connection 600mm long heavy duty suitable for hot and cold water, three core pvc insulated pvc sheathed copper conductor flexible cable, 04 nos suitable size mild steel l-hook fastener with washer for hanging the geyser and making good the disturbed surface complete all as specified and directed by engr-in-charge. 36 supply and fixing for led light fitting 1x9w/1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 37 supply and fixing earth continuity conductor or main earthing lead 32x6mm galvanised iron strip including nuts bolts and washer fixed to wall with saddles and fixing screws or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required including making good disturbed surface complete all as specified and as directed.note :- (i) conduit/pipe as required, same shall be measured & paid separately under respective item of this sch/boq. 38 subtotal 39 lump sum price worked out by the tenderer for“internal water supply works as listed in schedule ‘a’ section - iii (part-i) 40 sch a sec - iii (part-ii), internal water supply works 41 supply and fixing two way bib cock/angle stop valve with flange, cast copper alloy chromium plated, screwed down high pressure with on/off handle screwed ends suitable for 15 mm bore pipe iron pipe or for brass ferrule/unions and fixed complete all as specified and as directed. 42 supply and fixing chlorinated polyvinyl chloride (cpvc) pipe heavy duty outer dia 16 mm having thermal stability for hot and cold water supply including all new cpvc fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including cpvc solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by engineer-in- charge. note :- cutting chases if required same shall be measured and paid separately under appropriate item of boq. 43 supply and fixing chlorinated polyvinyl chloride (cpvc) pipe heavy duty outer dia 20 mm having thermal stability for hot and cold water supply including all new cpvc fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including cpvc solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by engineer-in- charge. note :- cutting chases if required same shall be measured and paid separately under appropriate item of boq. 44 supply and fixing chlorinated polyvinyl chloride (cpvc) pipe heavy duty outer dia 25 mm having thermal stability for hot and cold water supply including all new cpvc fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including cpvc solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by engineer-in- charge. note :- cutting chases if required same shall be measured and paid separately under appropriate item of boq.note for cpvc pipes : pipes inside the building shall be fixed concealed and outside the buildings shall be fixed on the surface with wall hooks as directed by engr-in-charge. 45 supply and fixing chlorinated polyvinyl chloride (cpvc) pipe heavy duty outer dia 40 mm having thermal stability for hot and cold water supply including all new cpvc fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including cpvc solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by engineer-in- charge. note :- cutting chases if required same shall be measured and paid separately under appropriate item of boq.note for cpvc pipes : pipes inside the building shall be fixed concealed and outside the buildings shall be fixed on the surface with wall hooks as directed by engr-in-charge. 46 supply and fixing single lever concealed diverter incl bath spout & shower complete all as specified and as directed by engineer-in-charge. 47 supply and fixing for brass chromium plated aquaguard/ro inlet valve or diverted valve with nozzle compatible for all type of water purifier fixing to steel pipe of socket of 15mm bore complete all as specified and as directed by engineer-in-charge. 48 supply and fixing for 40mm bore cpvc long handle vavle complete all as specified and as directed by engineer-in-charge. 49 supply and fixing health faucet fancy type, cp including 1.25 meter long 8mm dia flexible tube and including wall hook and fixing material complete all as specified and as directed by engineer-in-charge. 50 subtotal 51 lump sum price worked out by the tenderer for“road, pcc tiles andhume pipe culvert works) as listed in schedule ‘a’ section -iv (part-i) 52 sch a sec - iv (part-ii), road, pcc tiles andhume pipe culvert works 53 material and labour for premix bituminous concrete 40mm consolidated thicknesswith min 5.4 % binder content (bitumen of grade vg-30)by weight of total mix using sensor paver electronic sensing device for automatic leveling and profile control withi the specified toleranceand internal heating arrangement for the screed all as specified in table 500-17 of morth specification for road and bridge works 2013, rolled and compacted to required camber and gradient with tandem vibratory roller 8 to 12 tonne power roller to a uniform smooth surface complete all as specified and as directed by engineer-in-charge. 54 material and labour for thermo plastic paint road marking 2mm thick painting (lines, dashes, arrows, letters etc) with road safety spikeries glass beads @ 8% by weight including preparation of new or previously treated road surfaces and applying paint by using special applicator machine with heating arrangement complete all as specified and as directed by engineer-in-charge 55 supply and laying/fixing 80mm thick factory made chamfered edge cement concrete paver block of m-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & lick compacted bed farce dory meinod using fu mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete all as specified and as directed by engineer-in-chargenote:- tiles shall be approved by ge before incorporation in the work. 56 material and labour for sand cushioning, with dry and clean tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed.note:- (i) punned thickness shall be considered for payment purpose (ii) approved sand free from vegetations, grass and other deleterious substances shall be used. 57 material and labour for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed. 58 subtotal 59 lump sum price worked out by the tenderer for“(area drainageworks) as listed in schedule ‘a’ section -v 60 lump sum price worked out by the tenderer for“sewage disposal works as listed in schedule ‘a’ section - vi (part-i) 61 sch a sec - vi (part-ii), sewage disposal works 62 supply and laying dwcpe (sn8) drain pipes 180 (od)/163(id) mm dia pipe as per is-16098 (part-ii), laid in trenches on and including bed 100mm thick beding comprising of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to required slope, including all accessories/fittings/jointing ring, jointing and testing complete all as specified and as directed by engineer-in-charge.note : excavation, earth work and pedestal /anchorage if required shall be measured & paid separately under respective item of sch 63 supply and laying dwcpe (sn8) drain pipes 200 (od)/175(id) mm dia pipe as per is-16098 (part-ii), laid in trenches on and including bed 100mm thick beding comprising of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to required slope, including all accessories/fittings/jointing ring, jointing and testing complete all as specified and as directed by engineer-in-charge.note : excavation, earth work and pedestal /anchorage if required shall be measured & paid separately under respective item of sch. 64 subtotal 65 lump sum price worked out by the tenderer for“security fencing and gate works as listed in schedule ‘a’ section - vii 66 lump sum price worked out by the tenderer for “external water supply works as listed in schedule ‘a’ section-viii (part-i) 67 sch a sec - viii (part-ii),external water supply works 68 supplying, laying, jointing and testing ductileiron pipe (isi marked) class k-7, bore 150mm, confirming to is : 8329-2k, spigot & socketed ends centrifugally cast, with cement mortar lining inside and metallic zinc coating with finishing layer of bituminous paint on outside the pipe, suitable for and including rubber tyton joints (push-on joint) complete all as specified and as directed by engineer-in-charge.note : (i)earth work, di specials/ fittings shall be measured and paid separetly however cost of joining is included in overall cost quoted by the contractor. (ii) test certificate for pipes from manufacturer shall be produced. no payment shall be entertained without test certificate. 69 supply and fixing cast iron sluice valve 150 mm dia with flanged ends class pn 1.6(heavy duty isi marked) confirming to is:14846-2000, drilled type, complete with stainless steel spindle, ci gate with brass ring, iron wheel handle, complete including jointing material such as nuts, bolts, washers and rubber sheet insertion 3.0mm thick at both ends etc complete all as specified and as directed by engineer-in-charge. 70 material and labour for construction of brick masonary valve pit chamber size 90 x90 x90 cm (internal dimension) using sub class b bricks complete including excavation & earth work, returning fillig and disposal of surplus soil to distance not exceeding 50m and deposited where directed, pcc (1:3:6) type c-2 using 40 mm graded stone aggregate in foundation, coping on top in pcc (1:2:4) type b-1 using 20 mm graded stone aggregate, brick work in cement mortar (1:4), inner plaster 12 mm thick in cm (1:3) finished even and smooth and pionting flush externally as the work proceeds in the same mortar, ms sheet cover 3.15mm thick mounted on angle iron frame of size 40 x 40 x 6mm with handle and locking arrangement duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer and embeded portion of ms work duly applying black bitumenous paint before embeded complete all as specified and as directed by engineer-in-charge. 71 subtotal 72 lump sum price worked out by the tenderer for“external electrification and lightning protection works as listed in schedule ‘a’ section - ix (part-i) 73 sch a sec - ix (part-ii), external electrification and lightning protection works 74 supply and fixing lightning arresters ht 11000 v non linear expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp, confirming to is 3070 (part-i) 1985 complete all as specified and as directed by engineer-in-charge. 75 supply, installing, commissioning & testing energy efficient transformer suitable for 315 kva (level-2) step down floor mounted outdoor type 11/0.433kv, 3 phase, 50 hz ac, double wound core type copper wound, oil immersed, air naturally cooled with external cooling tubes, transformer delta connection on hv side and star connected on lv side in accordance with vector symbol dyn-11 (vector group 4) with neutral brought out on lv side with for earthing and having tapping on hv side for constant output so as to alter/vary secondary voltage (tapping range + 5 %to - 10% in equal step of 2.5 % ) changed by means of manually operated off load taps changing gear. the voltage regulation shall be as per is including first fill of transformer oil as per is-335 and including all fittings/accessories. the limit of temperature rise after continuous full load run as specified in is-1180 (part-i) 2014 and bee certified shall be suitably adjusted to suit the maximum ambient temperature of 55 degree centigrade as prevalent complete all as specified and as directed and shall be comprised with the following fittings and accessories :- 76 (a) oil conservator tank with fillings holes and cap filter type drain valve and oil level gauge. (b) silica gel breather with connecting pipe, first fill of dehydrating agent. (c) explosion relief mounted on tank with double diaphram and equalizer pipe connected to conservator air tank (pressure release valve) (d) air release valve plug (e) one cable box on lv side (secondary) consisting of 04 nos porcelain bushing with nuts, washers & bushing rods with 01 cable gland suitable for reception of taking out suitable size cable, including gland joints complete all as specified (f) explosive vent (g) 01 no 100 mm dial type thermometer vapor pressure type having range 0-120 degree centigrade with max temp indicator and resetting device incl max reading pointer washer etc. (h) thermometer pocket on tank cover (j) 04 nos plain solid ci detachable rollers (k) two nos earthing terminals marking plate. (l) rating plate and terminal marking plate(m) extra bushing for neutral outside the cable box brought out on lv side. (n) first filling of oil conforming to is and tested upto 60 kv dielectric strength (o) lifting lugs (p) oil drain valve with plug (q) one cable box on hv side (primary) consisting of 01 cable gland suitable for reception of taking in ht cable including gland joints complete all as specified (r) hand hole of sufficient size to assess interior of tank (s) dehydrating breather with first filling of dehydrating agent (t) two earthing terminal on tank body to facilitate fixing of 32x6mm gi strip. (u) rating plate with terminal marking plate (v) inspection cover. 77 supply, installation, commissioning and testing of factory made (cpri approved) lt panel board of suitable size, outdoor type (double door both side openable including locking arrangements) 415 volts, dust proof, vermin proof made out of crca sheet 3.15 mm thick powder coated and fully compartmentalized inner panel with 2 mm thick crca sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including provision of rubber beading and brass cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with separate bus bar chamber, panel shall be mounted on angle iron frame and 04 nos legs made from angle of size 50x50x6mm, legs shall be 750 mm long, 300 mm grouted in blocks of pcc (1:2:4) type b-1 (using 20 mm graded stone aggregate) with 450 mm ground clearance, frame and legs duly spray painted with seven tank process internally and externally with two coats of synthetic enamel over a coat of red oxide primer, internal wiring of panel board with solid conductor copper cable single core of suitable size, danger notice plate for lt with conventional skull and bones duly rivited/ pasted to the panel board door, complete including all connection incoming/ outgoing all as directed by engr-in-charge and comprising of following accessories:- 78 (a) copper bus bar of 800 amp capacity, 4 strip mounted on porcelain insulators. (b) mccb 4 pole with thermal magnetic release adjustable type with breaking capacity 36 ka, 500 amp (incomming).(c) mccb 4 pole with thermal magnetic release adjustable type with breaking capacity 25 ka, 125 amp - 07 (for 07 blocks).(d)mcb tpn 32 amps -01 nos (for street lights).(e) digital voltmeter 96x96mm flush secure panel mounting type 0-500v with selector switch -01.(f) digital amp meter 96x96mm flush secure panel mounting type 0-400amp with selector switch with ct -01. (g) ryb led indicating lamp set of three -01. 79 supply, installation, commissioning and testing of factory made (cpri approved) lt panel board of suitable size, outdoor type (double door both side openable including locking arrangements) 415 volts, dust proof, vermin proof made out of crca sheet 3.15 mm thick powder coated and fully compartmentalized inner panel with 2 mm thick crca sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including provision of rubber beading and brass cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with separate bus bar chamber, panel shall be mounted on angle iron frame and 04 nos legs made from angle of size 50x50x6mm, legs shall be 750 mm long, 300 mm grouted in blocks of pcc (1:2:4) type b-1 (using 20 mm graded stone aggregate) with 450 mm ground clearance, frame and legs duly spray painted with seven tank process internally and externally with two coats of synthetic enamel over a coat of red oxide primer, internal wiring of panel board with solid conductor copper cable single core of suitable size, danger notice plate for lt with conventional skull and bones duly rivited/ pasted to the panel board door, complete including all connection incoming/ outgoing all as directed by engr-in-charge and comprising of following accessories:- 80 (a)aluminium bus bar cap 150 amp capacity with heat shrinkable pvc colour sleeves - 04 nos.(b) mccb 4 pole with thermal magnetic release adjustable type with breaking capacity 36 ka, 100 amp (incomming).(c) mcb spn with thermal magnetic release adjustable type with breaking capacity 16 ka, 32 amp - 16 (outgoing).(d) digital voltmeter 96x96mm flush secure panel mounting type 0-500v with selector switch -01.(e) digital amp meter 96x96mm flush secure panel mounting type 0-400amp with selector switch with ct -01. (f) ryb led indicating lamp set of three -01. 81 supply, installation, commissioning and testing of factory made (cpri approved) lt panel board of suitable size, outdoor type (double door both side openable including locking arrangements) 415 volts, dust proof, vermin proof made out of crca sheet 3.15 mm thick powder coated and fully compartmentalized inner panel with 2 mm thick crca sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including provision of rubber beading and brass cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with separate bus bar chamber, panel shall be mounted on angle iron frame and 04 nos legs made from angle of size 50x50x6mm, legs shall be 750 mm long, 300 mm grouted in blocks of pcc (1:2:4) type b-1 (using 20 mm graded stone aggregate) with 450 mm ground clearance, frame and legs duly spray painted with seven tank process internally and externally with two coats of synthetic enamel over a coat of red oxide primer, internal wiring of panel board with solid conductor copper cable single core of suitable size, danger notice plate for lt with conventional skull and bones duly rivited/ pasted to the panel board door, complete including all connection incoming/ outgoing all as directed by engr-in-charge and comprising of following accessories:- 82 (a)aluminium bus bar cap 150 amp capacity with heat shrinkable pvc colour sleeves - 04 nos.(b) mccb 4 pole with thermal magnetic release adjustable type with breaking capacity 16 ka, 100 amp (incomming).(c) mcb spn with thermal magnetic release adjustable type with breaking capacity 16 ka, 20 amp - 07 (outgoing).(d) digital voltmeter 96x96mm flush secure panel mounting type 0-500v with selector switch -01.(e) digital amp meter 96x96mm flush secure panel mounting type 0-100amp with selector switch with ct -01. (f) ryb led indicating lamp set of three -01. 83 supply and fixing cable junction box of size 280mm x 200mm x100mm or any other higher size (suitable for pole mounting) complete with fixing accessories. junction box should be insulated and made out of polycarbonate with glass fiber re-inforced material. the polycarbonate junction box shall be environment frinedly, recyclable, uv resistant, halogen and silicon free, anti acid and anti corrosive. the junction box knock out on four side wall and following specifications and all as directed by engr-in-charge :-(a) the junction box shall be rated for degree ofip 65 (ingress protection) in accordance with iec 60529.(b) the gasket material shall be polyurethane or silicon and gasket shall be internally embedded.(c) junction box must meet the provision laid down in iec 60998-1, iec-60695-22, iec 60670-2 to 5 and grey color according to ral-9011/ 7035.(d) the manufacturer of junction box shall submit a copy of iec certificate and glow wire test for 960 degree.(e)junction box shall be fire retardant and self extiguishing in accordance with iec60695-2 to 11, din vde 0304 part-3, ul94 v-2 flammability standard. (f) the impact strength of polycarbonate enclosures /boards i.e. the degree of protection against mechanical load shall be in accordance with en 50298-98 for ik08.(g) junction box shall have 4 pole tinned copper bus bar of size 25mmx3mm complete with one number 20amp mcb sp 10ka (h) manufacturer should submit routine test certificate for junction box. (j) suitable size of mild steel clamps and screws/nut bolt shall be used for fixing of junction box.. 84 material and labour for earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including giearthing strip 32x6mm by means of gi bolts/nuts/washers and protected by 40 mm bore gi light grade pipe upto 7.5 mtr length, fixing with 02 nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore gi medium grade pipe for watering and including funnel, wire mesh, pcc chamber pit made with pcc (1:3:6) type c1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m,pit cover 40mm thick made with rcc (1:2:4) type b1 (using 20 mm graded stone aggregate) including tmt reinforcement 8mm dia @ 75mm c/c both way, ms handle 12mm dia, cover rest on ms angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate no. 3 ofssr 2009 (part-i) complete all as specified and as directed by engineer-in-charge.note:- (i) pcc chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) protection pipe and gi earthing strip upto 7.5 mtr from top of earth plate shall be included in the unit rate of this item. (iii) the earth testing arrangement should be done by the contractor as per direction of engineer-in-charge. 85 material and labour for sand cushioning, with dry and clean tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed.note:- (i) punned thickness shall be considered for payment purpose (ii) approved sand free from vegetations, grass and other deleterious substances shall be used. 86 s&f for gi steel light grade 32 mm dia bent to shape of offset angle upto 45 degree for fixing of security light fitting gi pipe 1.5 mtrs including ms clamp and nut bolts complete all as specified and as directed by engr-in-charge. 87 subtotal 88 sch a sec - x, fire fighting eqpt works 89 supply and fixing fire hydrant landing valve type a (double head outlet) gunmetal of 65 mm dia with 63 mm dia female outlet complete and 65 mm inlet with rubber blank cap and chain as per is 5290-1983, suitable for brigade hose of 63 mm with couplings conforming to is 903 (for internal hydrant at ground floor to 3rd floor and roof) complete all as specified and as directed. 90 supply, installing, commissioning and testing of fire hose cabinet to be mounted externally near the hydrant post fabricated from 16 swg mssteel of appox size 800 mm x 600 mm x 450 mm with a canopy, door with 4 mm glass encased in heavy grade rubber beading, a key box in built in the box, suitable to accommodate one hydrant valve, one branch nozzle and 30 mtrs hose reel, weather proof, finished with and including painting of two coats of synthetic enamel paint of post office red colour over a coat of red oxide primer ( sample to be approved prior to entire supply) complete all as specified and as directed. 91 supply, installing, commissioning and testingof wall mounting swinging type first aid firehose reel with drum, hanging bracket, 30 mtr long and20mm dia high pressure hose reel as per is 444 with gunmetal shut off nozzle having 5mm dia orifice. the hose reel shall be conforming to is 884-1985. drum shall be fixed on adjoining wall through anchor fasteners/cement concrete book or ms stand as per site requirement complete all as specified and as directed. 92 supply, installing, commissioning and testing of 63mm dia gun metal, short type, instantaneous pattern branch pipe to suit fire hose delivery coupling of 63 mm size complete with gm nozzle of 20 mm nominal size conforming to is 8090 complete all as specified and as directed. 93 supply, installing, commissioning and testing of gun metal body butterfly valves of size 63mm dia, is:210, pn-16, confirming to is:13095 complete all as specified and as directed. 94 supply, installing, commissioning and testing of booster pump 30 m head, 450lpm discharge, 440 v, 3 phase, 50hz confirming to is- 12469 :1988 with ci casing bronze impeller and stainless steel shaft mounted on heavy duty bearings complete all as specified and as directed. 95 supply, installing, commissioning and testing 65mm nominal bore, wall thickness 6mm, ms heavy duty (c class) flanged pipe, isi marked (is : 1239) with all necessary fittings & fabrication like tees, elbows, flanges, reducers, gaskets, nuts and bolts etc welding or screwed joints as required including fixing of pipe with necessary standard clamps structural steel supports (chilly make) as required/directed at site including painting of two coats of synthetic enamel paint of post office red colour over two coats of red oxide primer complete all as specified and as directed. 96 supply and fixing trolley mounted water stored pressure type fire extinguishers, 9 ltr capacity conforming to is:13386 with extinguishing agent :water+afff and propelling nitrogen gas, wall bracket handle fitted with high pressure flexible discharge hose with discharge throw of 2-5 mtrs.,with isi certification markcomplete all as specified and as directed. 97 supply and fixing carbon-di-oxide 3 kgs capacity fire extinguisher (light weight squeeze grip type) fitted with high pressure wire braided hose and horn shall be flat type and equipped with diffuser inside the horn, and cylinder bearing no., confirming to is:15683:2006. fire rating 3a: 89b, isi certification mark complete all as specified and as directed. 98 supply and fixing dry chemical powder fire extinguisher ( abc powder ) 9 kgs capacity stored pressure type, ce mark valve with nrv & safety release provision with epdm rubber hose, the extinguisher is internally coated with epoxy polyester and externally coated with pure polyester powder and confirming to is:15683:2006. fire rating 3a: 89b, isi certification mark complete all as specified and as directed. 99 supply and fixing mechanical foam extinguisher of 9 ltr capacity and confirming to is:15683:2006 complete all as specified and as directed. 100 supply and fixing fire buckets (dry sand)of 7 kg capacity including hanging arrangements complete all as specified and as directed. 101 supply and fixing emergency exit sign board with double side adhesive tape vinyl sticker with forex board (green and white colour) 30 cm x 10 cm complete all as specified and directed. 102 subtotal 103 lump sum price worked out by the tenderer for“lift works as listed in schedule ‘a’ section - xi (part-i) 104 sch a sec - xi (part-ii), (lift works) 105 supply, installing, commissioning and testing 13 passenger lift, having 1.0 m/s car speed, gearless motor suitable for 3- ph, 415 v, 50 hz electric power supply, conforming to is-14665, suitable to serve g + 3 upper floors with ac variable voltage & variable frequency drive (vvvf drive), complete with all standard accessories, simplex full collective operation, centre opening doors with door drive, sliding stainless steel doors, automatic rescue device (ard) system, 2d infrared sensor in full height of door & built in press and speak 3 way intercom. complete all as specified and as directed and shall conform to the following specifications: 106 type of lift : passenger lift 107 capacity of lift : 884 kg, 13 person 108 rise : up to g+3 bldg 109 stop and opening - 04 stops with all opening on the same side 110 controller type : microprocessor based 111 drive : ac vvvf drive 112 power supply : 400/415 volts (3 phase ac) 113 operation : full collective operation 114 car group : simplex type 115 machine : gearless motor located above shaft in machine room 116 traction media : steel rope 117 car finish : rear mid panel, rear corner panel, side mid panels, side corner panels, front panels all are made of stainless steel ss304 with honey comb finish 118 false ceiling finish : stainless steel with hairline finish and with provision for led lights specified here-in-after. 119 ventilation : pvc heavy duty cross flow fans 120 hand rails : stainless steel finish round handrails on rear car panels 121 flooring :20mm thick granite to be provided in the recess car cabin floor and fixing with suitable adhesive over aluminium chequered plate in one piece minimum 3mm thick. 122 car door and landing door finish : stainless steel ss-304, mirror finish outside 123 fire rated doors : fire rating - 60 minutes 124 pit depth: 1600 125 overhead : 4500 126 hoistway dimensions(w x d – mm) : 2500 mm w x 1900 mm d 127 car size (w x d x h - mm) : as per is-14665 (part 3 sec-i) : 2000, height 2200 mm 128 car & hoistway door type : central opening (co) doors 129 door opening (w x h - mm) : 900 mm w x 2000 mm h 130 door operator : vf 131 cop : cop (car operating panel) and lop (landing operating panel) in stainless steel hairline finish with display. 132 car position indicator : dot matrix type 133 hall fixtures : dot matrix type 134 hall fixture face plate : stainless steel hairline finish-ss-304 135 hall button arrangement: hall and call buttons with illumination and braille 136 car and counter weight guide as per oem recommendation 137 terminal buffers metal spring/oil buffer as per oem recommendation 138 standard features :anti-nuisance car call protection, independent service, overload device, nudging, emergency car light unit, infrared curtain door protection, door time protection, emergency alarm button, extra door time of lobby & parking door open/close button, manual rescue operation, auto fan cut off, over speed governor for car 139 also included : emergency firemen’s service, automatic rescue operation, intercom. 140 car enclosure: manufactured with stainless steel frame not less than 1.5mm with honey combfinish (ss-304) having stainless steel false ceiling with hairline finish, internal lighting arrangement with led sleek light fittings (as per manufacturer’s instructions, minimum 04 nos) operated on commercial supply and one led light fitting operated on battery with inverter as emergency light, complete internal ventilation system provided with concealed axial / cross flow fan with auto cut-off system and stainless steel grill / wire-mesh for protection 141 floor announcement system in car cabin 142 signals: (a) combined luminous hall buttons with led hall position indicators at all floors (b) led car position indicator panel of stainless steel (c) car operating panel of stainless steel with luminous buttons in car (d) car direction indicator in car & landing (e) battery operated alarm bell & emergency light (rechargeable) along with suitable maintenance free battery. (the system shall be separate from ard batteries.) (f) overload warning feature in car cabin (display / announcing type both) (g) one firemans switch to be installed at ground floor near landing door. (h) all signal fixtures & car operating panel on hairline stainless steel face plate with hairline finish (j) infrared door sensor safety edge of door for entire height. 143 safety device: (a) automatic rescue device (ard) / automatic landing device operating with maintenance-free batteries having suitable capacity. the batteries must have auto charging facilities. (b) the ard actuation time shall be less than one second after failure of power supply and when ard is operative the car shall stop at the nearest floor and then doors shall open. 144 operation: simplex, full collective automatic operation 145 machine room: located above the hoist way, details as per building drawings 146 hoist way: construction details as per building drawings 147 civil work: necessary civil work viz. making good disturbed surfaces, modification to landing space to suit car size, necessary foundation to machine(s), etc. 148 one number of wall mounted type telephone instrument installed inside of car cabin along with fixing arrangement and telephone cable of suitable size from car cabin to machine room run along with travelling cable. the telephone instrument shall be connected in the telephone db installed in the machine room 149 looking mirror of size 1200x900mm, 5.5mm thick to be provided on rear panel wall (opposite to main door) of car cabin above hand rail 150 provision of suitable size of copper conductor xlpe insulated cable from lift panel installed at ground floor to machine room will deemed to be included the rate quoted by the contractor 151 subtotal 152 lump sum price worked out by the tenderer for“excavation, earthwork and site development works as listed in schedule ‘a’ section - xii 153 schedule a section -xiii (furniture works) 154 almirah small steel as per drawing no. fd-1032 sheet no. 1/1 155 book shelf open (large) steel as per drawing no. fd-69(m) sheet no. 1/1 156 bed hard as per drawing no. fd/e6/map/08(r) sheet no. 1/1 157 chair verandah as per drawing no. fd/e6/map/11 sheet no. 1/1 158 charpoy folding ip with hard top as per drawing no. fd-388(r) sheet no 1/1 159 peg table as per drawing no. fd/map/11 sheet no. 1/1 160 rack shoe steel as per drawing no. fd/e6/map/02(r) sheet no. 1/1 161 table bed side as per drawing no. fd/e6/map/15(r) sheet no. 1/1 162 table centre as per drawing no. fd/map/08 sheet no. 1/1 163 dressing table including stool as per drawing no. fd/map-ii/07 sheet nos 1/2 & 2/2 164 chair dining jcos/ors as per drawing no. fd/map-ii/05 sheet no. 1/1 165 chair easy per drawing no. fd-229 sheet no. 1/1 166 chair writing as per drawing no. fd-280 sheet no. 1/1 167 charpoy with hard top as per drawing no. fd/map-ii/01 sheet no. 1/1 168 mirror dressing(gents) as per drawing no. fd/e6/map/16 sheet no. 1/1 169 table dining 4 persons as per drawing no. fd/map-ii/03 sheet no. 1/1 170 table with drawer (900 mm x 600 mm x 760 mm) as per drawing no. fd-283 sheet no. 1/1 171 chair school with hand board as per drawing no. fd/e6/map/05 sheet no. 1/1 172 note:-quantities of materials given on standard drawings are for guidance only. the contractor shall work out the quantities of materials required for each item of boq and quote his rate accordingly no claim shall be entertained on account of inaccuracy in the quantities of these materials and workman ship which shall be as specified in particular specifications and as approved. the drawing nos mentioned in boq item no 184 to 264 shall form part of tender document which will not be attached with tender document. the tenderers are deemed to be in possession and conversant fully with the drawing shown in standard furniture designs including amendments published by ahq, engineer-in -chief, new delhi. for reference and guidance the tenderer may study and see these drawings in the any office ofgarrison engineer in mes before quoting their rates. no claim shall be entertained regarding misinterpretation of the drawings at a later stage. 173 subtotal 174 lump sum price worked out by the tenderer for“arboriculture works as listed in schedule ‘a’ section - xiv (part-i) 175 schedule a section -xiv (part-ii) (arboriculture works) 176 material and labour for grassing with selection no.1 grass including enough watering and maintance of the lawn till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed including supplying and spreading of neem oil cakes, manure or sludge and chemical required for preparation of the ground for plantation of grass complete all as specified and as directed. 177 supply and planting of hedge and shrubbery (anarmi, ficus and the like) as directed by engineer-in-charge minimum 3 feet above gl including creation of beds by excavating 60 cm deep and 60 cm wide trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio 8:1 (8 part of stacked volume of earth after reduction of 20 % with 1 part of stacked volume of sludge or manure ater reduction by 8%) flooding with water filling with earth if necessary, watering and finally fine dressing leveling etc including stacking and disposal of material declared unserviceable and surplus earth by spreading and leveling as directed within a lead 50 m and lift upto 1.50 m complete all as specified and as directed. 178 supply and laying/fixing 60mm thick factory made chamfered edge cement concrete paver block of m-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & lick compacted bed farce dory meinod using fu mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete all as specified and as directed by engineer-in-chargenote:- tiles shall be approved by ge before incorporation in the work. 179 material and labour for sand cushioning, with dry and clean tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed.note:- (i) punned thickness shall be considered for payment purpose (ii) approved sand free from vegetations, grass and other deleterious substances shall be used. 180 supply and laying factory made kerb stone of size 30x15x45cm of m-25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed by engineer-in-charge 181 supplying following plants in poly bags 0.25 m to 0.30m dia with height 1.20 m to 1.80 m including digging holes 1.20m dia x1.2m deep in ordinary soil and refilling the same with the excavated earth mixed with manure of approved quality or sludge in ratio 2:1(2 parts of stacked volume of earth after reduction of 20% with 1 part of stacked volume of sludgeor manure after reduction by 8%) flooding with water and removal of surplus soil, with & including antitermite treatment using suitable chemicals or pesticides of approved quality, as required and making thaola all as specified and as directed by engineer-in-charge.note :- contractor shall maintain the trees till physical completion of contract.unit rate quoted is inclusive of replacement of dead trees,manures and all fertilizers mentioned above is inclusive in rate quoted. 182 neem tree. 183 canerydate palm 184 gulmohar 185 fruit bearing trees 186 plumeria 187 supplying plants flower like ticoma, rose,motia, chandni, lxora, marigold rose, vinca (any colour) as directed of height not less than 0.60m above gl including digging holes 1.20m dia x1.2m deep in ordinary soil and refilling the same with the excavated earth mixed with manure of approved quality or sludge in ratio 3:1(one part of manure & 3 part of soil) manure 200 gm per plant ,flooding with water and removal of surplus soil n.exc 1.50 km and depositing where directed with & including using suitable chemicals or pesticides of approved quality, as required and making thaola all as specified and as directed by engineer-in-charge.note :- contractor shall maintain the trees till physical completion of contract.unit rate quoted is inclusive of replacement of dead trees,manures and all fertilizers mentioned above is inclusive in rate quoted. 188 supply and fixing precast rcc 1:1.5:3 type a1 lawn bench and backsupport of size 1.50 x 0.60m of maximum three person seating capacity supporting precast rcc type a1 for back and base with including assemble the precast member with suitable nutt & bolt and placing and anchoring with hold fast 350mm - 16mm dia ms bar on concrete base (size 1.20x0.60m for each support) with 100mm thick pcc 1:2:4 type b1 over 150mm thick sub base pcc 1:4:8 type d2 complete all as specified and as directed by engineer-in charge 189 subtotal 190 schedule a section -xv ( maintance) 191 material and labour for the plants/hedge/grass by weeding, hosing, saucer making once in every month for plants/hedge, once in every 15 days for carpet grass/country grass/doob grass, bermuda grass, pruning dired ranches once in every week, depositing the material at place of dead plants of same species and height turning with dods whenever required by replacing the dead patches of grass of any type with same grass as required without any extra cost to the department all as specified and as directed. (plants of various species -678 nos (approx), hedge and shruery - 520 rm (approx) and grass - 4000 sqm( approx) 192 subtotal

Government Departments

TRN :49054816 | 06 Jun, 2025

Tender Value : 0

Vijaypur - Karnataka

Tender for supply of blood bank items & kits for the year 2024-25 to district hospital vijayapur - anti ab 1x5 ml,bloodbankitems002 1,micropipette 10microlitre to 200 microlitre adjustable,matrix low ionic strength solution 750 ml 1x1,malaria kit rapid 1x1,vdrl(rpr) kit 1x1,paper roller for elisa reader (silicon 2 inch),bloodbankitems008 2,bloodbankitems009 3,sponge balls required for blood donor,bloodbankitems011 4,blood bag single 350 ml cpda 1x1 needle with triple bevel and hot marking in donor tube,blood bag double 350 ml cpda 1x1 needle with triple bevel and hot marking in donor tube,blood bag triple 450 ml cpda 1x1 needle with triple bevel and hot marking in donor tube,bloodbankitems015 5,bloodbankitems016 6,bloodbankitems017 7,transfer blood bags 100 ml haemopack,bloodbankitems019 8,bloodbankitems020 9,anti a, anti b, anti ab, anti d blend combipack 4x12 ml (tulip or similar),bloodbankitems022 10,bloodbankitems023 11,bloodbankitems024 12,bloodbankitems025 13,anti h lectin 5 ml 1x1,anti d i g g 5 ml 1x1,glass test tube 12x75ml 1x1,bloodbankitems029 14,bloodbankitems030 15,bloodbankitems031 16,bloodbankitems032 17,bloodbankitems033 18,gel cards for forward grouping (required for card warmer model cw-2400 and card centrifuge model junior cc-0800 make - matrix gel systems) 1x24 cards,gel cards for reverse grouping (required for card warmer model cw-2400 and card centrifuge model junior cc-0800 make - matrix gel systems) 1x24 cards,gel ahg cards (required for card warmer model cw-2400 and card centrifuge model junior cc-0800 make - matrix gel systems) 1x24 cards,bloodbankitems037 19,bloodbankitems038 20,bloodbankitems039 21,blotting paper 50x65 cms,copper sulphate powder 500 gms,haemopack 100 ml paediatric blood bag

State Government

TRN :49020396 | 14 May, 2025

Tender Value : 0

Belagavi - Karnataka

Tender for tender for rate contract supply of disposable items to bims belagavi - corrugated drain.,water - bed,visualis-100-irrigation-aspiration-tubing-set-reusable,vaccum-suction-set-non-toxic-pyrogen-free-sterilised-disposable-ce/iso-certified(yankur-suction-set),urine-container-30ml,urine-collection-bag-1.5ltr,umbilical-venous-catherter-no5,umbilical-venous-catherter-no4,umbilical-venous-catherter-no3.5,umbilical-artery-catheter-5f,twin-bore-nasal-canula-adult,tracheostomy-tubes-with-no8.5-cuff-protex-or-equivalent,tracheostomy-tubes-with-no7.5-cuff-protex-or-equivalent,tracheostomy-tubes-with-no7.0-cuff-protex-or-equivalent,tracheostomy-tubes-with-no6.0-cuff-protex-or-equivalent,tracheostomy-tubes-with-no5.0-cuff-protex-or-equivalent,tracheostomy-tubes-with-no.0-cuff-protex-or-equivalent,tracheostomy-tubes-silicon-uncuff-size(pead)5.0,tracheostomy-tubes-silicon-uncuff-size(pead)4.5,tracheostomy-tubes-silicon-uncuff-size(pead)4.0,tracheostomy-tubes-silicon-uncuff-size(pead)3.5,tracheostomy-tubes-silicon-uncuff-size(pead)3.0,tracheostomy-tubes-silicon-uncuff-size(pead)2.5,tracheostomy-tubes-kit-uncuff-size4.5,tracheostomy-tubes-kit-uncuff-size4,tracheostomy-tubes-kit-uncuff-size3.5,tracheostomy-tubes-kit-uncuff-size3,tracheostomy-tubes-kit-size4.5,tracheostomy-tubes-kit-size4,t - protector,thermal-paper(high-quality)for-use-with-edan-se-1200-ecg-machine(1x100)-packa4-size,suction-catheters-no8,suction-catheters-no6,suction-catheters-no16,suction-catheters-no14,suction-catheters-no12,suction-catheters-no10,stillets-fitting-for-sizes7-endotracheal-tube,stillets-fitting-for-sizes4-endotracheal-tube,stillets-fitting-for-sizes3-endotracheal-tube,stillets-fitting-for-sizes2.5--endotracheal-tube,stillets-fitting-for-sizes2-endotracheal-tube,sterile-disposable-infusion-set(iv-infusion-set),steri-drape-for-ent,stehtoscope-peadiatric,stehtoscope-adult,stainless-steel-hydro-cannula-no.24,spinal-needle-no27g,spinal-needle-no26g,spinal-needle-no25g,spinal-needle-no24g,spinal-needle-no23g,spinal-needle-no22g,spinal-needle-no20g,spinal-needle-no18g,spc-catheter-malecot-with-stillete-fr20,spc-catheter-malecot-with-stillete-fr18,spc-catheter-malecot-with-stillete-fr16,spc-catheter-malecot-with-stillete-fr14,spc-catheter-malecot-with-stillete-fr12,spc-catheter-malecot-with-stillete-fr10,spc-catheter.,sony-thermal-glossy-paper-rolls-for-ultra-sound-typev,skin-staplers-disposable-35w-regular-size,skin-grafting-blade(humby-knife-blade),simcoe-irrigating-aspirating-cannula-22g,simco-cannula-no.22,siliconized-endotracheal-tubes-size4.5-without-cuff,siliconized-endotracheal-tubes-size4.0-without-cuff,siliconized-endotracheal-tubes-size3.5-without-cuff,siliconized-endotracheal-tubes-size3.0-without-cuff,siliconized-endotracheal-tubes-size2.5-without-cuff,siliconized-endotracheal-tubes-size2.0-without-cuff,side-port-blade-,septal-buttons,scented-masks-inflatable-cuff5,scented-masks-inflatable-cuff4,scented-masks-inflatable-cuff3,scented-masks-inflatable-cuff2,sanitary-napkin(size-extra-large),ryles-tube-no8,ryles-tube-no6,ryles-tube-no5,ryles-tube-no18,ryles-tube-no17,ryles-tube-no16,ryles-tube-no14,ryles-tube-no12,ryles-tube-no10,ryles-tube-no.-20,rubber-toniquet-no.6,rubber-toniquet-no.4,romovac-drain16,romovac-drain14,romovac-drain12,red-rubber-torniquet-4inch,red-rubber-catheter-no8,red-rubber-catheter-no7,red-rubber-catheter-no12,red-rubber-catheter-no11,red-rubber-catheter-no10,rae-ivory-pvc-nsala-tubes-with-soft-seal-cuff6,radiography-dry-laser-films-14inchx17inch(shall-give-one-cr-film-printer-free-of-cost-which-should-be-compatible-with-existing-fuji-cr-reader),radiography-computer-radiography-film-8inchx10inch(shall-give-one-cr-film-printer-free-of-cost-whichshould-be-compatible-with-existing-fuji-cr-reader),proseal-laryngeal-mask-airway-reusable-no4,proseal-laryngeal-mask-airway-reusable-no3,pigtail-catheter-8,pigtail-catheter-20,pigtail-catheter-18,pigtail-catheter-12,photo-therapy-eye-pad/goggles,phaco-tubings,peripherally-insrted--central-catheter-picc,pelvic-binder-l-size,papsmear-kit-(cytobrush-with-spatulla),oxygen-mask(adult),oxygen-mask-paediatric,ot-mask-with-tie-knot,optivantage-high-pressure-syringe-200ml,nrb-mask,north-polar-preformed-ivory-pvc-nasal-tubes-cuff8,north-polar-preformed-ivory-pvc-nasal-tubes-cuff7,north-polar-preformed-ivory-pvc-nasal-tubes-cuff6.5,nasal-splints-(internal-nasal-splints),nasal-splints-(external-nasal-splints),nasal-canula-paediatrics,nasal-02cannula-,n95-mask,micro-drip-set,measured-volume-set(coomb-set),long-arm-splint-universal,laryngscope-paediatric-conventional-4blades-set,laryngscope-adult-conventional-4blades-set,laparoscopic-tubal-ligation-band,lacrimal-stent,keratome-blade-2.8mm,iv-extension-3way-10cm,iv-extension-100cm,iobon-(antimicrobial-incise-drape-60x45-cm),iobon-(antimicrobial-incise-drape-34x35-cm),intubating-styleptes-small,intubating-styleptes-medium,intubating-styleptes-large,intubating-lma-reusable-size5,intubating-lma-reusable-size4,intubating-lma-reusable-size3,intrajagular-catheter-no10,intra-oculr-lens(foldable)no9-injector-system-preferably-2.8mm,pigtail-catheter-14,intra-oculr-lens(foldable)no8-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no6-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no5-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no23-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no22-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no21-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no20-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no19-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no17-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no16-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no15-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no14-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no13-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no12-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no11-injector-system-preferably-2.8mm,intra-oculr-lens(foldable)no10-injector-system-preferably-2.8mm,intra-ocular-lens(sf-iol)dia-13.5mm-optic6.5-size21,intra-ocular-lens(sf-iol)dia-13.5mm-optic6.5-size20,intra-ocular-lens(sf-iol)dia-13.5mm-optic6.5-size19,intra-ocular-lens(sf-iol)dia-13.5mm-optic6.5-size18,intra-ocular-lens(sf-iol)dia-13.5mm-optic6.5-size17,intra-ocular-lens(pciol)no26-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no25-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no24-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no23-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no22-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no21-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no21.5-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no20-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no20.5-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no19-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no19.5-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no18-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no17-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(pciol)no16-optic-diameter-5.25mm-and-size-13mm,intra-ocular-lens(iris-claw)size-5.5x8mm-no24d,intra-ocular-lens(iris-claw)size-5.5x8mm-no23d,intra-ocular-lens(iris-claw)size-5.5x8mm-no22d,intra-ocular-lens(iris-claw)size-5.5x8mm-no16d,intra-ocular-lens(iris-claw)size-5.5x8mm-no21,intra-ocular-lens(iris-claw)size-5.5x8mm-no20,intra-ocular-lens(iris-claw)size-5.5x8mm-no19,intra-ocular-lens(iris-claw)size-5.5x8mm-no18,intra-ocular-lens(iris-claw)size-5.5x8mm-no17,intra-ocular-lens(aciol)no19.5-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no19-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no18-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no17-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no16-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no15-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no14-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no12-optic-diameter5.25mm-and-size-13mm,intra-ocular-lens(aciol)no11-optic-diameter5.25mm-and-size-13mm,intersurgical-i-gel-no.-5.0,intersurgical-i-gel-no.-4.0,intersurgical-i-gel-no.-3.5,intersurgical-i-gel-no.-3.0,infant-feeding-tube-no9,infant-feeding-tube-no8,infant-feeding-tube-no7,infant-feeding-tube-no6,infant-feeding-tube-no5,infant-feeding-tube-no10,ijc-dialysis-catheters-dual-luman-with-ctheter-kit-curved-extension-and-laser-cut-side-slots-3.8mmx13.5,i-gel-supraglottic-airways(inter-surgical)-size2.5,i-gel-supraglottic-airways(inter-surgical)-size2,i-gel-supraglottic-airways(inter-surgical)-size1.5,i-gel-supraglottic-airways(inter-surgical)-size1,icds-bags,icd-tubes-trocer-no32,icd-tubes-trocer-no30,icd-tubes-trocer-no28,icd-tubes-trocer-no24,icd-tubes-trocer-no16,icd-tubes-trocer-no14,heparinised-syringes-(for-abg-analysis)(plastic-round-disposable-heparin-coated-abg-syringe,14g,-packet),hemolock-(weck)-clips-size-600,hemolock-(weck)-clips-size-400,hemolock-(weck)-clips-size-200,hb-strips-with-machine(should-give-one-machine-free-of-cost-for-each-500-strips),glucometer-strips-with-machine(should-give-one-machine-free-of-cost-for-each-1000-strips),folleys-catheters-no.22,folleys-catheters-no.20,folleys-catheters-no.18,folleys-catheters-no.16,folleys-catheters-no.14,folleys-catheters-no.12,folleys-catheters-no.10,folleys-catheters-no.08,folleys-catheters-no.06,folleys-catheter-three-way--22fr,folleys-catheter-three-way--20fr,folleys-catheter-silicone-two-way-18fr,folleys-catheter-silicone-two-way-16fr,folleys-catheter-silicone-two-way-14fr,extension-with-integrated-bi-way-50cm,extension-with-integrated-bi-way-25cm,extension-with-integrated-bi-way-10cm,examination-gloves(small-size),examination-gloves(medium-size),examination-gloves(large-size),examination-gloves(extra-small-size),endotracheal-tubes-size9.5with-cuff,endotracheal-tubes-size9.0without-cuff,endotracheal-tubes-size9.0with-cuff,endotracheal-tubes-size8.5without-cuff,endotracheal-tubes-size8.5with-cuff,endotracheal-tubes-size8.0without-cuff,endotracheal-tubes-size8.0with-cuff,endotracheal-tubes-size7.5without-cuff,endotracheal-tubes-size7.5with-cuff,endotracheal-tubes-size7.0without-cuff,endotracheal-tubes-size7.0with-cuff,endotracheal-tubes-size6.5without-cuff,endotracheal-tubes-size6.5with-cuff,endotracheal-tubes-size6.0without-cuff,endotracheal-tubes-size6.0with-cuff,endotracheal-tubes-size5.5without-cuff,endotracheal-tubes-size5.5with-cuff,endotracheal-tubes-size5.0without-cuff,endotracheal-tubes-size5.0with-cuff,endotracheal-tubes-size4.5without-cuff,endotracheal-tubes-size4.5with-cuff,endotracheal-tubes-size4.0without-cuff,endotracheal-tubes-size4.0with-cuff,endotracheal-tubes-size3.5without-cuff,endotracheal-tubes-size3.5with-cuff,endotracheal-tubes-size3.0without-cuff,endotracheal-tubes-size3.0with-cuff,endotracheal-tubes-size2.5without-cuff,endotracheal-tubes-size2.5with-cuff,endotracheal-tubes-size2.0without-cuff,endotracheal-tubes-size2.0with-cuff,elbow-gloves(small),elbow-gloves(medium),elbow-gloves(large),elastic-adhesive-bandage-10cmsx4/6mtr,ecg-rolls-106mm-4inch,ecg-paper-roll-size-3inch(80mm-x-20-mtrs),ecg-chest-leads-disposable,ear-foam-tips-small-size.,ear-foam-tips-big-size.,ear-foam-tips-for-paediatrics-packets,ear-foam-tips-for-adults-packets,dry-laser-films-14inchx17inch(shall-give-one-cr-film-printer-free-of-cost-which-should-be-compatible-with-existing-fuji-cr-reader),disposable-syringe-5ml-with-23g-needle,disposable-syringe-50ml-with-needle,disposable-syringe-2ml-with-23g-needle,disposable-syringe-20ml-with-needle.,disposable-syringe-1ml-26x1.5-g,disposable-syringe-10ml-with-needle,disposable-plastic-sheet,disposable-plastic-apron-material-hmhd/ldp-plastic-colour-medical-blue-length-52inch-56inch-(below-the-knee)-size-medium-blood-and-water-resistant-fits-men-and-women,disposable-ot-masks-three-layer-with-6.5inch-ear-loop-melt-blown-cloth-and-non-woven-material-colour-medical-blue-dimension-6.88-inchx-3.74inch-outside-layer-leak-proof-non-woven-abric(25gsm)middle-layer-high-density-filter-yer(25gsm)-melt-blown-fabric-bfe-more-and-equivalent-to95%inner-layer-direct-contact-skin-layer-non-woven-fabric-quad-fold-design-pleat-depth-design-5/8inch-size-universal-certification-ce-iso/astm-level1,disposable-ot-caps-25-gsm-medical-grade-polypropylene-spun-bond-non-woven-materials-with-ultrasonic-sealed-with-small-elastic-at-the-back,disposable-needle-no26g-half-inch,disposable-needle-no.-24g,disposable-needle-no.-20g,disposable-needle-no.-18g,disposable-microtone-blade-high-profile-set,disposable-mackintosh-sheet,disposable-iv-cannula-26g,disposable-iv-cannula-24g,disposable-iv-cannula-22g,disposable-iv-cannula-20g,disposable-iv-cannula-18g,disposable-iv-cannula-16g,disposable-insulin-syringe-1ml(0.25x6mm),disposable-hiv-protection-kit hiv-kits-discription.-(1) surgical-gown-1piece (2) face-mask-1piece (3) face-protector-1piece (4) head-cap-1piece (5) shoe-cover-1 piece (6) gloves-1 piece,disposable-gown,disposable-glove-7inch(pair)-disposable-sterile-isi-or-ce-marked-gloves,disposable-glove-7.5inch(pair)-disposable-sterile-isi-or-ce-marked-gloves,disposable-glove-6inch(pair)disposable-sterile-isi-or-ce-marked-gloves,disposable-glove-6.5inch(pair)disposable-sterile-isi-or-ce-marked-gloves,disposable-crescent-blades,disposable-bed-sheet-colour-medical-blue-disposable-breathable-chemical-free-skin-friendly-bacterial-and-viral-barrier-tear-and-puncture-resisitant-impervious-and-repellant-to-fluids-adhesive-strip-fitted-elastic-on-all-boundaries-sterilized-dimension-and-weight-width-160cm-length-180cm-weight-of-bedsheet-130gram-material-nonwoven-fabric-polycoated-gsm-of-non-woven-material(g/m2)-40-to-60certifications-and-reports-aami-protection-level-level-iv-certification--iso-13485-medisurge-or-equivalent,disposable-a-scopy-shaver-4.00mm,disposable-1.5inch-needle-length,-26-gauge-needle-thickness-and-2ml-syringe-with-thread-locking-system-(unilock),disafe-plus-,diaper(adult)m-l(30inch-to-50inch),diaper-newborn(2-5kg),dialyser-suitable-for-fresenius-dialyser-machine0.8(m2)inline-steam-sterilization-reusable,dialyser-suitable-for-fresenius-dialyser-machine(f6)1.3(m2)inline-steam-sterilization-reusable-,dermatome.,dcr-stents-(dacrocystorhinostomy),dark-goggle,cord-clamp,computer-radiography-film-8inchx10inch(shall-give-one-cr-film-printer-free-of-cost-whichshould-be-compatible-with-existing-fuji-cr-reader),collegen-sheet-dressing,chest-drain32,chest-drain30,chest-drain28,chest-drain24,central-venous-line7,central-venous-line6.5,central-venous-line6.0,central-venous-line5,central-venous-line4.5,central-venous-line4,central-venous-line3.5,blood_lancet.,central-venous-line3.0,central-line-triple-lumen-,central-line-double-lumen-,cannula-fixator-,caesarian-drape-sterilized-disposable-non-woven-material-disposable-breathable-chemical-free-skin-friendly-bacterial-and-viral-barrier-tear-and-puncture-resisitant-impervious-and-repellant-to-fluids-colour-medical-blue-43gsm-size-160cmx250cm-43gsm-8mms-100cmx80cm-absorbent-80gsm-10inch-hole-2inch-adhesives-with-butter-paper,bone-wax-2.5gms-each-pkt,-1-box-contains-12-pieces-per-box,blood-transfusion-set,blood-tubing-set,blood-bags-double-450-ml,blood-bags-double-350-ml,biway-cannula,biopsy-disposable-punches--3.5,biopsy-disposable-punches--3,biopsy-disposable-punches--2.5,biopsy-disposable-punches--2,b-p-blade-no11,b-p-blade-no.12,b-p-blade-no.-21,b-p-blade-no.-20-,b-p-blade-no.-15,avf-needle-17g,a-scopy-burr-4.mm,angiographic-syringe-ct-and-mr-connector-pipe-compatable,angiographic-syringe-connection-pipe-two-way/by-way,angiographic-syringe-connection-pipe-single-way,angiographic-disposable-syringe-ct-and-mri-4x12,angiographic-disposable--syringe-200ml,ambu-bag-set-autoclavable-paediatric,ambu-bag-set-autoclavable-neonatal,ambu-bag-set-autoclavable-adult,ambu-bag-reservior-750ml,ambu-bag-reservior-500ml,ambu-bag-reservior-250ml,ambu-bag-reservior-1000ml,ambu-bag-face-mask-size2,ambu-bag-face-mask-size1,ambu-bag-face-mask-size00,ambu-bag-face-mask-size0,airways-no-3,airways-no-2,airways-no-1,air-bed-,adhesive-abdomen-drape,abgel-(gel-foam),abdominal-drain-kit-size-32,abdominal-drain-kit-size-30,abdominal-drain-kit-size-28,abdominal-drain-kit-size-26,abdominal-drain-kit-size-24

Central Government/Public Sector

TRN :34426933 | 16 May, 2025

Tender Value : 0

Mumbai - Maharashtra

Tender for gem bids for colin glass cleaner 550 gms , lizol surface cleaner 500 ml , liquid hand wash with dispenser bottle pump 200 ml , hand wash refill pack 750 ml , heavy duty plastic dustpan with handle. , toilet brush round 16 x 01 cm , harpic disinfectant toilet cleaner liquid 01 ltr , dish wash liquid gel lemon 250 ml , scotch brite scrub pad small 7.5 cm x 7.5 cm , dish or wash basin plastic cleaning brush with liquid soap dispenser , stainless steel scrubber for utensils 18 grams , godrej automatic room freshers with flexi control spray 225 ml , godrej air matic refill automatic room fresheners 225 ml , godrej air power pocket 30 gms , mosquito repellent combi pack machine and pack of 02 refills , refills for mosquito repellent machines 45 ml , mosquito racket bat rechargeable , extension board with 5 meter long cord 06 socket with 06 switch , foldable umbrella black colour handle length 24 inch , portable umbrella black colour handle length 38 inch , aa duracell high power battery 1.5 v , aaa duracell high power battery 1.5 v , tissue paper napkin 30 x 30 cm 100 nos per pkt , stainless steel open top round dustbin silver colour 8 x 12 inches , gala spin mop extendable handle or stick rod with microfibre refiles , gala quick spin mop refill , plastic wiper with telescopic handle 30 cm , floor wiper with handle big size 05 feet , ceramic serving tray 12 x 18 inch , floor cleaning grass broom , hand towel 450 gms, multi colour ultra soft and super absorbent 14 x 21 inches , white phenoyl 1 ltr pack , plastic water bottel 1 ltr cello h2o , aa duracell rechargealbe high power battery 1.5 v , charging adeptor for aa duracell rechargealbe battery 1.5 v , biodegrable rat repellent garbage bag 25 x 30 inch per pack 30 , heavy duty silicone hand gloves with scrubber , plastic bucket 20 ltr , gala spin mop with bucket , steel wool grade 1 bundle , urinal pad , odoni

State Government

TRN :34428892 | 15 May, 2025

Tender Value : 0

Nagpur - Maharashtra

Tender for gem bids for beaker 50ml , beaker 100ml , beaker 250ml , funnel , filter paper no 4 , filter paper no 42 , thimble for extraction , rubber tubing , air reflux condenser , silica dish 100 ml , silica crucible 50 ml , volatile oil trap lighter than water , aluminium foil roll , specific gravity bottle -25ml , specific gravity bottle -50ml with thermometer 00c to 500c , volumetric flask 5ml , micropipette tips 1ml 10 pack of 1000 , pipette graduated cap 2 ml calibrated-class-a , pipette graduated cap 10 ml calibrated-class-a , pipette graduated cap 5 ml calibrated-class-a , pipette -bulb-cap-25 ml calibrated -class-a , pipette cap-50 ml calibrated -class-a , flat bottom flask with b-24 joint cap 250 ml , measuring cylinder cap. 10 ml calibrated , cylinder graduated cap. 25 ml calibrated , cylinder graduated cap. 100 ml calibrated , separating funnel 125 ml , separating funnel 500 ml , blue litmus paper , sugar flask , pre coated silica gel plates , burette 10ml .graduation-0.01ml calibrated-class-a , micro pipette 0.5-5 ml with respective 100no tips and tip box , micro pipette 0.1-1.0 ml respective 100no tips and tip box , micro pipette 1.0-10ml with respective 100no tips and tip box , silicone tubes , inoculation loop , measuring cylinder 100ml , test tubes culture tubes , petri plate dish , tissue roll jumbo size 5 inch roll , micro pipette 0.5-5 ml with respective 100 no tips and tip box , heat resistant gloves , nitrile gloves , corrugated box , zip lock heavy duty ldpe pouch , zip lock ldpe pouch , wide mouth bottles , narrow mouth bottles

Central Government/Public Sector

TRN :34413605 | 12 May, 2025

Tender Value : 0

Jharsuguda - Orissa

Tender for gem bids for glass ionomer cement g c fuji japan p l15 gm 10 ml 0r 8 ml , k file 40 to 80 25mm , k file no 10 to 40 25 mm , cement mixing spatula , cryers right and left set , probe , polishing strips packet of 100 , rubber bowl , mani bur size sf 11 , mani bur size sf 12 , mani bur size tf 11 , mani bur size tf 12 , mani bur size sf 12 ef , mani bur size tr 26 ef , mani bur size tf 13 ef , mani bur size ex 21 ef , mani bur size rs 11 , mani bur size br 13 , mani bur size ex 11 , mani bur size ex 12 , mani bur size ex 21 , mani bur size tf-12 , mani bur size tf-13 , mani bur size sf-13 , mani bur size tr 12 , mani bur size tr 13 , mani bur size wr 13 , inverted cone bur , oro wooden wedge box , composite nano kit , endobox , gdc periosteal elevator sabanca unit , gdc tissue retractor regwell davis , gdc serrated lower root forcep 1 unit , gdc serrated upper root forcep 1 unit , gdc lower 3rd molar extraction forcep fx 79s , s s suture cutting scissor premium quality , b p blade handle no 3 and 4 2 each , gdc mouth mirror set of 12 , gdc london college tweezer , suction tip disposable 100 unit premium quality , stright hand pc for micromotor unit , gp f1 , gp f2 , gp f3 , paper point f1 to f3 , protaper gold sx 1 set consist of 6 nos , protaper point s1 1 set consist of 6 nos , protaper gold s2 1 set consist of 6 nos , prtaper gold f1 1 set consist of 6 nos , potaper gold f2 1 set consist of 6 nos , potaper gold f3 1 set consist of 6 nos , universal single bond 3m 5 ml , edta solution , gp solvent , k file no 10 21 mm 1 set consist of 6 nos , k file no 15 21 mm 1 set consist of 6 nos , k file no 20 21 mm 1 set consist of 6 nos , h file no 15 21mm 1 set consist of 6 nos , h file no 20 21 mm 1 set consist of 6 nos , h file no 25 21 mm 1 set consist of 6 nos , h file no 30 21 mm 1 set consist of 6 nos , addition silicon flexceed , epoxy resin based root canal sealer , impression tray perforated , chlorhexidine irrigating solution 2percent , metapex , metapaste , extraction foreceps set of 12 , elevator foreceps set of 9 , periosteal elevator , etching gel 2 5 ml , edta gel 6 gm , algitex impression 750 gm , eugenol 110ml , g p point 15 40 , g p point 45 80 , lutingcement , cement carrier , dental probe , mta with multiple vials and gel 1 gm powder 2ml liquid 2ml gel , air rotar hand piece , suction cleaning and disinfection liquid

Central Government/Public Sector

TRN :34403316 | 10 May, 2025

Tender Value : 0

Agatti - Lakshadweep

Tender for gem bids for international pearl night blue , interthane 990 phb 000a white , interthane 990 signal green , thinner gta 733 , tape transparent 38 mm , soap hard yellow , rope polypropylene 08 mm , rope polypropylene 06 mm , rope polypropylene 12 mm , rope polypropylene 10 mm , teflon thread seal tape , solder lead , sand paper , rubber latex long gloves , cable electric 2 core copper a , bucket plastic 15 ltrs , brush steel wire , boric powder , bleaching powder stabilized , baygon spray , araldite adhesive , anti cockroach gel chalk , battery connection lugs , 09 v battery , envelope cloth coated 10x14 , envelope cloth coated 9x12 , envelope cloth 10x14 , envelope cloth 6x12 , envelope cloth 4x10 , pencill cll 1.5 v , m seal , safey gloves cloth , abbrassive paper 230x280 mm silicon carbride , paper napkin , candle wax 19mm 500 grms pack , teflon tape , insulation tape 25 mm , antirust spray , tape transparent 2

Statutory Bodies and Commissions/Committees

TRN :48330395 | 15 May, 2025

Tender Value : 2.00 Crore

Shillong - Meghalaya

Tender for cardiac stents and consumables, on consignment basis , group –a1 consumables & accessories, etc , puncture needle for vascular access • 18g • 6-7.5 cm long • 0.038 inch guide wire compatible • should be supplied individually packed • needle should have protected plastic tube covering , puncture needle dedicated for radial artery access • 20-22g • 3-5 cm long • 0.021 or 0.025 inch guide wire compatible • should be supplied individually packed • needle should have protected plastic tube covering , doppler puncture needle (with facility of detecting doppler signals of vascular structures) , special puncture needle with facility of detecting ultrasound images of vascular structures) , introducer sheath for adults (size 4fr.-9fr.) (standard length) • sizes 4french/5 french /6 french /7 french /8 french /9 french. • 10-11 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , introducer sheath with puncture needle for adults (size 4fr.-9fr.) (standard length) • sizes 4french/5 french /6 french /7 french /8 french /9 french. • 10-11 cm long • pack must include 18 g, 6-7.5 cm long puncture needle • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , introducer sheath for adults (size 10fr.-11fr.) (standard length) • 10fr.& 11 fr. • 10-11 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , introducer sheath for adults (size 12fr. and higher) (standard length) • 12fr/13 fr./14 fr. and higher • 10-11 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , long introducer sheath (20-30 cm long) (size 5fr.-9fr.) • sizes 5 french /6 french /7 french /8 french /9 french. • sheath should be between 20-30 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , long introducer sheath (20-30 cm long) (size 10fr.-11fr.) • 10 french & 11 french • sheath should be between 20-30 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , patient transfer and or table super absorbent sheet having loading capacity upto 150 kg size 210x80cm • composite of air formed nonwoven and cross-linked acrylate copolymer. • hotmelt adhesive based hydrocarbons, styrene, rubber copolymer and resin. • loading capacity of 150kg • dimension of 210cm x 80cm absorption capacity of 1.5 ltr , extra thin floor cover made with clean, extremely absorbent cellulose-based material having thermo-mechanic fibre connectors without adhesive and binding agents for freely and swiftly absorption of fluid, non-slip backside, retains 1.5 to 1.7 ltr of fluids • supercore having cellulose and sodiumpolycarylate bonded with thermo-mechanic fibre connectors without any adhesive and binding agents • pp-nonwoven hydrophiliated surface and rear side • quick absorption facility with long-term binding of large quantities of liquid upto 1.7 ltr • extra thin and individual cuttable • easy in use on floors, tables and beds in operating theatres during medical examinations • facility to absorb fluids from both sides • non-slip proof backside having size of 116cm x 76cm , breathable fluid and germ impermeable, skin friendly having smooth surface transfer and repositioning sheet retains upto 1.9 ltr of fluids and upto 100kg weight capacity • odourless, insoluble fluid and germ impermeable skin friendly • supercore® technolgoy composite of 76% cellulose and 24% sodiumpolyacrrylate for impressive absorbency and excellent fluid dispersion than conventional airlaids • having weight of ca. 295g • having loading capacity upto 100kg with dimension of 80 x 210cm having absorption capacity of 2900 ml/pc or 1800ml/m2 , radiation protection body contoured endoskeleton with 0.5mm lead equivalence. bilayer for protection, with mantis arms, proprietary illiac crest belt for efficient weight redistribution ensuring no weight on the shoulders and spine • bilayer with mantis arms, iliac crest belt for efficient weight redistribution to ensure no weight on shoulder and spine • made with highest quality core material product in lead and non-lead materials • having durable and flexible endoskeleton • having comfort and adjustable belt with memory foam interior and spacer mesh to help regulate users temperature • available in 0.5mm lead equivalence available in small, medium, large and x-large stocked , group –a2 , long introducer sheath (20-30 cm long) (size 12fr. and higher) • 12fr./13 fr./14 fr. and higher • sheath should be between 20-30 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , long introducer sheath (30-50 cm long) (size 5fr.-9fr.) • sizes 5 french /6 french /7 french /8 french /9 french. • between 30-50 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , long introducer sheath (30-50 cm long) (size 10 fr.-11fr.) • sizes of 10 french & 11 french • between 30-50 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , long introducer sheath (30-50 cm long) (size 12 fr. and higher) • sizes of 12 french/13 french/ 14 french and higher • between 30-50 cm long • 0.035 or 0.038 inch guide wire compatible with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , extra long introducer sheath (> 50 cm) (size 5fr.-9fr.) • 5 french /6 french /7 french /8 french /9 french. • more than 50 cm long • 0.035 or 0.038 inch guide wire compatible with haemostatic valve to prevent back leak and airaspiration • integral side port with attached 3-way stopcock • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , extra long introducer sheath (> 50 cm) (size 10 fr.-11fr.) • sizes of 10fr.& 11 fr. • more than 50 cm long • 0.035 or 0.038 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • integral side port with attached 3-way stopcock • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , extra long introducer sheath (> 50 cm) (size 12fr.and higher) • sizes of 12fr./13 fr./14 fr. and higher • more than 50 cm long • 0.035 or 0.038 inch guide wire compatible with haemostatic valve to prevent back leak and airaspiration • integral side port with attached 3-way stopcock • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • with smooth and resistance free insertion , introducer sheath dedicated for trans radial access • sizes from 4french/5french/ 6 french/7 french • between 7-11 cm long • 0.021 or 0.025 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • with integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • should have smooth and resistance free insertion , long introducer sheath dedicated for transradial access • sizes from 4french/5french/ 6 french/7 french • between 16-24 cm long • 0.021 or 0.025 inch guide wire compatible • with haemostatic valve to prevent back leak and air aspiration • with integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • should have smooth and resistance free insertion , transradial introducer kit • includes 21 g puncture needle • 0.021 inch introducer guide wire • introducer sheath sizes from 4french/5french/ 6 french/7 french • sheath size between 10-24 cm long , group - a3 , ptfe coated diagnostic guide wire - (regular length, regular stiffness) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be between 145-180 cm long • should be available as straight & j-shaped tip • should be available in variable lengths of flexible/floppy end • should be available in variable j tip sizes • should be available in fixed as well as movable core , ptfe coated diagnostic guide wire - (exchange length, regular stiffness) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be 240-300 cm long • should be available as straight or j-shaped tip • should be available in fixed as well as movable core , ptfe coated diagnostic 0.032 inch guide wire - (regular length, extrastiff shaft strength) -amplatz type • should be available in 0.032 inches size • should be between 145-180 cm long • should be available as straight & j-shaped tip , ptfe coated diagnostic 0.032 inch guide wire - (regular length, extrastiff shaft strength) -amplatz type • should be available in 0.032 inches size • should be between 240-300 cm long • should be available as straight & j-shaped tip , ptfe coated diagnostic guide wire - (regular length, extrastiff shaft strength) -amplatz type • should be available in 0.035 inches size and higher • should be between 145-180 cm long • should be available as straight & j-shaped tip , ptfe coated diagnostic guide wire - exchange length, extrastiff shaft strength) -amplatz type • should be available in 0.035 inches size and higher • should be between 240-300 cm long • should be available as straight & j-shaped tip , ptfe coated diagnostic guide wire - regular length,ultra stiff shaft strength) -amplatz super stiff type • should be available in 0.032, 0.35, 0.038 inches size • should be between 145-180 cm long • should be available as straight or j-shaped tip; should have extra ordinary or exceptional shaft strength , ptfe coated diagnostic guide wire - exchange length,ultra stiff shaft strength) -amplatz super stiff type • should be available in 0.032, 0.035 and 0.038 inches size • should be between 240-300 cm long • should have extra ordinary or exceptional shaft strength , pigtail catheter • 4french/5french/6french/7french/8french size • should be available in various lengths , angled pigtail catheter • 4french/5french/6french/7french/8french size • should be available in various lengths , group-a4 , pigtail catheter with marker • 4french/5french/6french/7french/8french size • should be available in various lengths , judkins catheter • 4french/5french/6french/7french/8french size left and right judkins catheters in various standard curves and lengths. , multipurpose catheter • 4french/5french/6french/7french/8french size multipurpose catheter in various standard curves and lengths. , amplatz catheter- 4french/5french/6french/7french/8french amplatz left (al) and amplatz right (ar) catheter in various standard curves and lengths , internal mammary catheter – • 4french/5french/6french/7french/8french in various standard curves and lengths , by- pass graft catheters- • 4french/5french/6french/7french/8french in various standard curves and lengths. , transradial diagnostic coronary catheters - • 4french/5french/6french/7french diagnostic coronary catheters of various curves and lengths dedicated for trans radial coronary angiography , nih catheter- • 4french/5french/6french/7french/8french in various standard curves and lengths. , cournard catheter- • 4french/5french/6french/7french/8french in various standard curves and lengths. , thermo dilution catheter • should be compatible with the available system , group –b1 , ptca inflation device • efficient locking system to maintain high pressure • rapid inflation and deflation • clear barrel for easy visualization of de-bubbling • luminescent analog pressure gauge (up to 30 atm) • ergomatric and user friendly hand held design , tuohy borst (haemostatic y-connector) for ptca- rotating mechanism • should accommodate virtually all interventional devices • large thumb wheel for easy maneuverability • luer connector at the guiding catheter end • rotating adapter at the guiding catheter end , tuohy borst (haemostatic y-connector) for ptca- push mechanism • should accommodate virtually all interventional devices • luer connector at the guiding catheter end • rotating adapter at the guiding catheter end • should have bleed back safety mechanism • stepwise control for open, semi-open and closed position , tuohy borst- double (haemostatic y-connector) for bifurcation ptca • two ports for insertion of interventional devices • luer connector at the guiding catheter end • rotating adapter at the guiding catheter end , large bore tuohy borst (haemostatic y-connector) , ptca guide wire torquer • should hold guide wires from 0.009-0.018 inches • ergomatric and user friendly design , ptca guide wire insertion needle • 20 g size • 10 -12 cm long • should hold up to 0.018 inch guide wire , ptca guide wire accessory kit containing • haemostatic y connector • ptca guide wire torquer • ptca guide wire insertion needle , ptca inflation device with accessory kit containing • ptca inflation device • haemostatic y connector • ptca guide wire torquer • ptca guide wire insertion needle , control syringes for ptca • clear, glass-like plastic syringe • markings up to 10 or 12 ml • palm and finger assisted easy maneuverability • plunger should have resistance free movement • should have a stopper with 0.5 ml reserve , group -b2 , connector tubing (connecting between touhy borst and manifold) • should be between 20- 50 cm • should have large i.d for easy flow of contrast • should take high pressure • should be flexible • should have male and female hubs , manifold for ptca with two side ports • large i.d for easy flow of contrast • smooth resistance free unidirection handle/knob , manifold for ptca with three side ports • large i.d for easy flow of contrast • smooth resistance free unidirection handle/knob , manifold with attached tubings • two side port manifold • one connector tubing for connecting manifold to tuohyborst • one luer lock control syringe (10 or 12 ml) for contrast injection • one large bore tubing (with flow regulating knob) for withdrawing contrast • one three way stop-cock , ptca kit: should contain the following items • one tuohyborst (haemostatic y- connector) • one two side-port manifold • one connector tubing for connecting manifold to tuohyborst • one luer lock control syringe having markings up to 10 or 12 ml for contrast injection • one ptca guide wire insertion needle • one ptca guide wire torquer • one large bore contrast tubing (with flow regulating knob) for attachment between contrast bottleand manifold side port • one pressure monitoring line (150 cm) • one three way stop-cock , femoral compression devices- disc/dome based compression , domes of femoral compression device , ptca guiding catheter- • sizes of 5fr, 6fr, 7fr and 8fr. • all possible shapes including catheters: judkins/femoral left and right, extra back up support,amplatz, voda, multipurpose, hockey stick, transradial interventions, bypass-graft/limainterventions and others • should also have availability of smaller length catheters (90 cm) • should also have availability of catheters with side holes • should also have short tip catheter , large lumen (i.d) ptca guiding cathete (6 french size) • must have i.d of more than 0.070 inch • should have all possible shapes including catheters: judkins/femoral left and right, extra back upsupport, amplatz, voda, multipurpose, hockey stick, transradial interventions, bypassgraft/lima interventions, short tip catheters and others , large lumen (i.d) ptca guiding cathete (7 french size) - • must have i.d of more than 0.080 inch • should have all possible shapes including catheters: judkins/femoral left and right, extra back upsupport, amplatz, voda, multipurpose, hockey stick, transradial interventions, bypassgraft/lima interventions, short tip catheters and others , guide extension catheter with the working length of 150 cm and guide extension segment upto 40cm with 1x1 stainless steel wire braiding with hydrophilic coating and compatible with 6f/7f and 8f femoral guide catheter , group -b3 , ptca guiding catheter for dca , ptca guide wire -regular length, regular shaft support and floppy tip , ptca guide wire -regular length, extra- support shaft and floppy tip , ptca guide wire - exchange length , ptca guide wire- hydrophilic coated, regular length , ptca guide wire- hydrophilic coated, exchange length , special ptca guide wires with elastinite core and stainless steel , shaft support • both regular and exchange length wires • should have wires with varying degree of shaft support , special ptca guide wire with dual coating • should have distal hydrophilic coating and proximal hydrophobic coating • should have wires with variable tip stiffness and variable shaft support , special ptca guide wire with multiple markers for measuring the length of stenotic segment , ptca guide wires for chronic total occlusion (cto) , group -b4 , special non-tapering ptca guide wires for cto with platinum iridiumdistal spring coil • wires available in variable distal tip stiffness, measured in terms of grams , special tapering ptca guide wires for cto with platinum iridiumdistal spring coil • wires available in variable distal tip stiffness, measured in terms of grams , special tapering ptca guide wires for cto withhydrocoathydrophiliccoating • wires available in variable distal tip stiffness , • special hydrophilic ptca guide wires for cto with super elasticalloy (ni-ti) core polyurethrane hydrophilic distal coating , special ptca guide wires for cto, dedicated for retrogradeapproach , extension (doc) wire for approved regular length ptca guide wires , penetration catheters for cto having rotational bluntpenetration , penetration devices for cto by blunt dissection using acuating jaws , ptca guide wire with bidirectional deflectable distal tip , ptca catheter with deflectable distal end • should guide the direction of ptca guide wire , cto reentry system with 2 over the wire lumens and 2 hubs, 3 exit ports for 360 degree functionality for sgr technique 18g • over the wire dual wire lumen micro catheter • 1.5f lesion entry profile* • two separate otw lumens and three exit ports 360 degree guidewire redirection option , dual lumen device for simultaneous haematoma aspiration and redirection of guidewire in true lumen in complex cto cases, 360 degree access • 2.3fx3.3f distal shaft profile and 2.6fx3.4f proximal shaft profile • 0.014” guidewire compatibility • usable length of 140cm additional exit port in the tip lumen of the exit port of the stylet lumen , trapping device for wire trapping used with otw devices with lowest shaft profile of 2f • single use device consisting of hub, shaft and balloon • highly compatible small shaft profile of 2f • designed to trap the guidewire at low inflation pressure depth marker for 90cm guide catheter , intra coronary guide extension catehter • flex zone and unique 3 zone transition for smooth trackability • highest coiling density for extra pushability • 25cm rapid exchange section • two exit markers at 95cm and 105cm working length of 150cm , group -b5 , ptca balloon (non-compliant) - • quote both monorail (rapid exchange) and otw balloons • available in all sizes from 2- 4.0 mm, variable lengths • should have a very high rated burst pressure , special large ptca balloons of more than 4 mm • variable lengths , special ptca balloon catheter with low crossing profile • must have crossing balloon profile of less than 0.025 inches , special ptca balloon catheter of less than 1.5 mm • should be available in variable balloon lengths , special otw ptca balloon for septal ablation for hocm , high pressure cto non compliant with low crossing profile (diameter 0.85mm) assorted sizes) • xr (excellent rewrap) balloon material with ultrathin marker bands • hydro-x hydrophilic coating (distal tip to exit port) • invio coating on guidewire lumen • sub-zero flex tip tapered tip with zero guidewire transition for smooth lesion • 0.85mm diameter • p-tech hypotube with excellent transitional balance, pushability and exceptional kink resistance • crossing profile of 0.0313 inches and tip entry profile 0.0208 inches available in sizes 1.5 – 5.00 mm diameter with length of 10,12,15, 20 & 30mm , group -b6 , ptca balloon for retrograde approach of cto • should be available in both regular and long lengths for retrograde approach , non compliant speciality balloon having the catheter length of 140 cm or more. tip entry profile of 0.019 inch or less and mid- balloon profile of 0.036 inch or less with 3/4 stainless steel cutting blades having a functional height of 0.005 inch. available in a working length of 6, 10 & 15mm and balloon having a working range between 6 to 12 atm. , scoring balloon catheter for ptca , dual wire ptca dilatation catheter , drug eluting ptca balloon using matrix technology , ptca bifurcation balloon , stainless steel coronary stents, premounted on balloon – , stainless steel coronary stents, premounted on balloon – , stainless steel coronary stents, premounted on balloon – , cobalt chromium balloon coronary stents, premounted onballoon – , group -b6- a , coronary stents : non-medicated coronary stent balloonmounted , non-medicated stent on stainless steel platform balloonmounted , non-medicated stent on non-stainless steel platform with uniform ultrathin struts ( up to 60 microns) balloonmounted , non-medicated stent on non-stainless steel platform with uniform thin struts ( 61 to 80 microns) balloonmounted , non-medicated stent on non-stainless steel platform with struts thickness ( > 80 microns) balloonmounted , non-medicated stent on non-stainless steel platform for coronary artery diameters all sizes including 4.5mm or more. balloonmounted , non-medicated stent on non-stainless steel platform for coronary artery disease all lengths including 8mm or less. , group -b6- b -coronary stents : non-medicated coronary stent , balloonmounted , non-medicated stent on stainless steel platform , balloonmounted , non-medicated stent on non-stainless steel platform with uniform ultrathin struts ( up to 60 microns) , balloonmounted , non-medicated stent on non-stainless steel platform with uniform thin struts ( 61 to 80 microns , balloonmounted , non-medicated stent on non-stainless steel platform with struts thickness ( > 80 microns) , balloonmounted , non-medicated stent on non-stainless steel platform for coronary artery diameters all sizes including 4.5mm or more. , balloonmounted , non-medicated stent on non-stainless steel platform for coronary artery disease all lengths including 8mm or less. , group -b6- b.coronary stents : medicated coronary stent -sirolimus eluting , balloon mounted, sirolimus eluting stent with biodurable polymer on stainless steel platform. , balloon mounted, sirolimus eluting stent with biodurable polymer on a non-stainless steel platform. , balloon mounted, sirolimus eluting stent with biodegradable polymer on stainless steel platform. , balloon mounted, sirolimus eluting stent with biodegradable polymer on cocr platform with hybrid stent design and uniform thin struts upto 65 micron, and diameter from 2.25 to 4mm of varying lengths from 10 to 40 mm. , balloon mounted, sirolimus eluting stent with biodegradable polymer on non-stainless steel platform with uniform thin struts (61-80 microns) , balloon mounted, sirolimus eluting stent with biodegradable polymer on non-stainless steel platform with uniform strut thickness greater than 80 microns. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) and diameters of 2.0mm to 4.00 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform thin struts (61 -80 microns) and diameters of 2.0mm to 4.00 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and diameters of 2.0mm to 4.00 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) and diameters of 2.25mm to 4.5 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (61-80 microns) and diameters of 2.25mm to 4.5 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and diameters of 2.25mm to 4.5 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) of varying lengths including stent length of 8mm or less. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (61-80 microns)of varying lengths including stent length of 8mm or less , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and of varying lengths including stent length of 8mm or less , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) of varying lengths including stent length of 48mm or more , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (61-80 microns) of varying lengths including stent length of 48mm or more , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and of varying lengths including stent length of 48mm or more , balloon mounted , polymer free, sirolimus eluting stent , group -b6- c - coronary stents : medicated coronary stent -drug eluting , balloon mounted, sirolimus eluting stent with biodurable polymer on stainless steel platform. , balloon mounted, sirolimus eluting stent with biodurable polymer on a non-stainless steel platform. , balloon mounted, sirolimus eluting stent with biodegradable polymer on stainless steel platform. , balloon mounted, sirolimus eluting stent with biodegradable polymer on cocr platform with hybrid stent design and uniform thin struts upto 65 micron, and diameter from 2.25 to 4mm of varying lengths from 10 to 40 mm. , balloon mounted, sirolimus eluting stent with biodegradable polymer on non-stainless steel platform with uniform thin struts (61-80 microns) , balloon mounted, sirolimus eluting stent with biodegradable polymer on non-stainless steel platform with uniform strut thickness greater than 80 microns. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) and diameters of 2.0mm to 4.00 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform thin struts (61 -80 microns) and diameters of 2.0mm to 4.00 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and diameters of 2.0mm to 4.00 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) and diameters of 2.25mm to 4.5 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (61-80 microns) and diameters of 2.25mm to 4.5 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and diameters of 2.25mm to 4.5 mm of varying lengths. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) of varying lengths including stent length of 8mm or less. , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (61-80 microns)of varying lengths including stent length of 8mm or less , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and of varying lengths including stent length of 8mm or less , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (upto 60 microns) of varying lengths including stent length of 48mm or more , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform ultrathin struts (61-80 microns) of varying lengths including stent length of 48mm or more , balloon mounted, sirolimus eluting stenton non-stainless steel platform with uniform strut thickness greater than 80 microns and of varying lengths including stent length of 48mm or more , balloon mounted , polymer free, sirolimus eluting stent , group -b6- d coronary stents : medicated coronary stent -drug eluting , balloon mounted, everolimus/zotarolimus eluting stent with biodurable polymer on stainless steel platform. , balloon mounted, everolimus/zotarolimus eluting stent with biodurable polymer on non-stainless steel platform. , balloon mounted, everolimus/zotarolimus eluting stent with biodurable polymer on non-stainless steel platform and diameters of 2.25mm or less to 4.00mm or more of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent with biodegradable polymer on non stainless steel platform. , balloon mounted, everolimus eluting stent with biodegradable polymer on cocr platform with hybrid stent design and uniform ultrathin struts ( upto 63 micron) and diameters of 2.25 to 4.00mm. , balloon mounted, everolimus/zotarolimus eluting stent with biodegradable polymer on non-stainless steel platform with uniform thin struts (61-80 microns) , balloon mounted, everolimus/zotarolimus eluting stent with biodegradable polymer on non-stainless steel platform with struts thickness greater than 80 microns. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with ultra thin struts ( upto 60 microns) and diameters of 2.0mm to 4.0mm of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform thin struts ( 61-80 microns) and diameters of 2.0mm to 4.0mm of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform strut thickness greater than 80 microns and diameters of 2.0mm to 4.0mm of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with ultra thin struts ( upto 60 microns) and diameters of 2.25 mm to 4.5mm of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform thin struts ( 61-80 microns) and diameters of 2.25 mm to 4.5mm of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform strut thickness greater than 80 microns and diameters of 2.25 mm to 4.5mm of varying lengths. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with ultra thin struts ( upto 60 microns) of varying lengths including stent length 8mm or less. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform thin struts ( 61-80 microns) of varying lengths including stent length 8mm or less. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform strut thickness greater than 80 microns and of varying lengths including stent length 8mm or less. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with ultra thin struts ( upto 60 microns) of varying lengths including stent length 48mm or more. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform thin struts ( 61-80 microns) of varying lengths including stent length 48mm or more. , balloon mounted, everolimus/zotarolimus eluting stent on non-stainless steel platform with uniform strut thickness greater than 80 microns and of varying lengths including stent length 48mm or more. , balloon mounted , polymer free, everolimus/zotarolimus eluting stent , usfda approved platinum chromium everolimus eluting des with abluminally coated bioabsorbable polymer having a thickness not more than 5?m and a bi segment shaft with a midshaft segment made of lasercut hypotube with the length >10cm and minimum of about 500 lasercuts. should be available in diameters from 2.25 to 5.00mm and lengths of 8,12,16,20,24,28,32,38 and 48mm and the total stent thickness < 90?m. , usfda approved platinum chromium everolimus eluting des specifically designed for left main and large proximal vessels with abluminally coated bioabsorbable polymer having a thickness not more than 5?m and a bi segment shaft with a midshaft segment made of hypotube with lasercuts and a 12 peak design. should be available in diameters from 3.50 to 5.00mm and lengths of 8,12,16,20,24,28 and 32 mm withthe overexpansion capability of minimum 6.00 mm. total stent thickness should be < 95?m , usfda approved platinum chromium everolimus eluting des with permanent polymer having a thickness not more than 5?m and a bi segment shaft with a midshaft segment made of lasercut hypotube with the length of 10cm and about 300 lasercuts. should be available in diameters from 2.25 to 4.00mm and lengths of 8,12,16,20,24,28,32 and 38 mm. , sirolimus coated drug eluting coronary stent. hybrid cell design, cobalt-chromium platform with biodegradable polymer, small strut thickness of 50 ?m 5f guide catheter compatible, with variable diameter and length available upto =48mm , everolimus coated drug eluting coronary stent. hybrid cell design, cobalt-chromium platform with biodegradable polymer, small strut thickness of 50 ?m 5f guide catheter compatible, with variable diameter and length available upto =48mm , sirolimus coated drug eluting tapered coronary stent with 0.5 mm difference of diameter between proximal and distal end.cobalt chromium platform with biodegradable polymer, small strut thickness, different diameter of upto 4.5mm (proximal end ) and length available upto = , group -b6- e. medicated coronary stent -paclitaxel eluting , balloon mounted, paclitaxel eluting stent with biodurable polymer on stainless steel platform. , balloon mounted, paclitaxel eluting stent with biodurable polymer on non-stainless steel platform. , balloon mounted, paclitaxel eluting stent with biodegradable polymer on stainless steel platform. , balloon mounted, paclitaxel eluting stent with biodegradable polymer on non-stainless steel platform. , balloon mounted, paclitaxel eluting stent on non-stainless steel platform and diameters of 2.0mm to 4.0mm of varying lengths. , balloon mounted, paclitaxel eluting stent on non-stainless steel platform and diameters of 2.25 mm to 4.5 mm of varying lengths. , balloon mounted, paclitaxel eluting stent on non-stainless steel platform of varying lengths including stent length of 8mm or less. , balloon mounted, paclitaxel eluting stent on non-stainless steel platform of varying lengths including stent length of 48mm or more. , group -b6- f coronary stents : medicated coronary stent -newer limus analogue ( other than sirolimus, everolimus, zotarolimus) , balloon mounted, newer limus analogue with biodurable polymer on stainless steel platform. , balloon mounted, newer limus analogue with with biodurable polymer on non-stainless steel platform. , balloon mounted, newer limus analogue with with biodegradable polymer on stainless steel platform. , balloon mounted, newer limus analogue with with biodegradable polymer on non-stainless steel platform. , balloon mounted, newer limus analogue eluting stent on non-stainless steel platform and diameters of 2.0mm to 4.0mm of varying lengths. , balloon mounted, newer limus analogue eluting stent on non-stainless steel platform and diameters of 2.25 mm to 4.5 mm of varying lengths. , balloon mounted, newer limus analogue eluting stent on non-stainless steel platform of varying lengths including stent length of 8mm or less. , balloon mounted, newer limus analogue eluting stent on non-stainless steel platform of varying lengths including stent length of 48mm or more. , balloon mounted ,newer limus analogue with abluminal drug coating. , group -b6- g other coronary stents , self - expanding drug eluting coronary stent dedicated for bifurcation lesion. , self - expanding drug eluting coronary stent dedicated for side branch access. , balloon mounted drug eluting , tapered coronary stents. , balloon mounted coronary stents covered with flexible mesh sleeve. , self expanding drug eluting coronary stents. , balloon mounted, dual drug coated drug eluting stents. , bioresorbable coronary vascular scaffold. , coronary stent graft/coronary covered stent with sandwich design of variable diameters and lengths. , coronary stent graft/coronary covered stent of variable diameters and lengths, with single stent design and 5 french guide catheter compatibility. , biodurable polymers includesibs( poly styrene-b-isobutylene -b styrene), pbma( poly-n-butyl methacrylate,peva ( polyethelene covinyl acetate), pvdf-hfp(poly vinlidine fluoride hexafluropropylene,0 pc( phosphoryicholine) siloxane copolymer and any other commercially approved biodurable polymer. , paclitaxel coated semi- compliant drug coated balloon having a drug load of less than 3 ?g/mm2 and a balanced hydrophilic hydrophobic excipient with a bi segment inner lumen shaft and a hydrophilic coating on the shaft. available in the diameters of 2.00 to 4.00 mm and lengths of 12mm, 15mm, 20mm & 30mm. working range of 6 to 14 atm for sizes upto 3.0mm & 6 to 12 atm for 3.50 mm & 4.00 mm. , biolimus aa drug eluting stent system • hybrid cobalt chromium stent • abluminal biodegradable polymer with biolimus a9 eluting stents • mid-section s-shape connectors • thin strut cobalt chromium • 1.37mm large cell opening for easy side branch access • excellent trackability and pushability together with low tip entry profile available in sizes of 2.25, 2.50, 2.75, 3.00, 3.50 & 4.00mm dia with stent length of 9, 14, 19, 24, 29, 33 & 36mm , polymer and carrier free drug coated stent with biolimus a9 (ba9) & microstructured abluminal surface, having lower peak force for better tracebility, higher pushability & large cell opening diameter • polymer free and carrier free drug coated stent • biolimus a9 (ba9) and micro structured abluminal surface • lower peak force for better traceability • higher pushability of 49 pft to increase the efficiency of the force • large cell opening diameter 1.702mm to provides better access to side branch for subsequent stents available in sizes of 2.25, 2.50, 2.75, 3.00, 3.50 & 4.00mm dia with stent length of 8, 11, 14, 18, 24, 28, 33 & 36mm , sirolimus eluting coronary side branch stent system.sizes available 2.5mm x 2.5mm,3.0mm x 2.5mm,3.5mm x 2.5mm, 3.5mm x 3.00mm 4.0mm x 3.5mm lengths 16mm, 19mm, 24mm, & 29mm , group-b10 , rotalink plus (advancer and burr) , rotational atherectomy guide wires , rotaglide lubricant , ivus catheter • should be compatible with available machine of make boston scientific , catheter for virtual histology • should be compatible with available machine , catheter for optical coherence refractometry • should be compatible with available machine , drug delivery/infusion catheter , coronary probing catheter , coronary perfusion catheter , coronary trapeer catheter , group--b11 , special micro -catheter for cto retrograde approach , thrombectomy catheters with manual suction during ptca , thrombectomy catheters with distal balloon occlusion andautomated suction during ptca , thrombectomy catheters with motorized cutting and suction during ptca , doppler wire for ptca , presssure wire for ptca , group-b12 , embolic protection devices based on filter technology/mechanism , embolic protection devices with distal balloon occlusive technology , embolic protection devices with proximal balloon occlusive technology , arterial puncture closure devices - collagen plug based , arterial puncture closure devices - suture based , disposable femoral compression devices- balloon based compression , compression devices for radial artery- balloon based compression , compression devices for radial artery- strap based compression , ptca guide wire re-entry catheter for cto , coronary micro catheter- , group –c (drugs used in cath lab during coronay interventios) , injection nikorandil (2 mg) , injection bivaluridin , injection tirofiban , injection eptifibatide , injection abciximab , group– d1 , puncture needle for vascular access for paediatric / neonatal use • 20-22g • 3-5 cm long • 0.021 or 0.025 inch guide wire compatible • should be supplied individually packed • needle should have protected plastic tube covering , intravenous cannula ‘medicut’ type for vascular access • available in 16, 18, 20, 22 g • supplied with an attached luer-lock 2 ml syringe • individually packed with easy peel off , intravenous cannula for vascular access • available in 16, 18, 20, 22 g • 20 g should allow the passage of 0.025 hydrophilic guide wire • individually packed with easy peel off , intravenous cannula for vascular access in neonates • available in 24, 26 g • individually packed with easy peel off , introducer sheaths for pediatric use (size 4-6fr.) with straight introducer wire • sizes 4french/5french/6 french • between 5.5-7.5 cm long • 0.021 inch straight introducer guide wire • with haemostatic valve to prevent back leak and air aspiration • with integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with dilator-hub lock mechanism to prevent its back-out during insertion • should have smooth and resistance free insertion , introducer sheaths for pediatric use (size 4-6fr.) with j tip introducer wire • sizes 4french/5french/6 french • between 5.5-7.5 cm long • with 0.021 inch introducer guide wire with j tip on one end and straight tip on the other end (bothends should be soft) • with haemostatic valve to prevent back leak and air aspiration • should have integral side port with attached 3-way stopcock • with suture eye for securing sheath • kink resistant • with a dilator-hub lock mechanism to prevent its back-out during insertion • should have smooth and resistance free insertion , introducer sheath of 3 french (fr.) size (for neonatal/ pediatric use) , pigtail catheter (pediatric) - • 4french/5french/6french size • smaller length for neonatal and pediatric use • must be fda approved , judkins catheter (pediatric) - • 4f/5f/6f size left and right judkins catheters in various standard curves and lengths. • must be fda approved , special judkins coronary catheter with 2.5 cm curve (pediatric) • 4f/5f/6f , group-d2 , multiprpose catheter (pediatric) • 4f/5f/6f in various standard curves and lengths , 3- french’ diagnostic catheters for neonatal use • pigtail, judkins, multipurpose, cobra and other diagnostic catheters of 3 fr. size • varying lengths and shapes , special swan ganz catheter with: • 4f catheter should allow the passage of at least 0.021 inch, 5f – 0.025 inch, 6f – 0.035 inch and 7f,8f – 0.038 inch hydrophilic guide wire • must be available in 4f, 5f, 6f and 7f and 8 fr. sizes • catheter should be tapered at tip to ensure uniform diameter of the whole catheter • 10 cm marking along catheter body to confirm insertion depth , balloon tipped angiography catheter , berman cathter • must be available in 4f, 5f, 6f and 7f sizes • should have 6 - 8 holes proximal to the balloon for dye injection • catheter should be tapered at tip to ensure uniform diameter of the whole catheter • 10 cm marking along catheter body to confirm insertion depth , reverse berman catheter • should be available in 4f, 5f, 6f & 7f sizes • catheter should be tapered at tip to ensure uniform diameter of the whole catheter • should have holes proximal to the balloon for dye injection • should have a hole at the proximal tip to allow the passage over the wire , mullins sheath without side arm • should be available in 6 fr./7 fr./ 8fr. sizes • thick and stiff dilator for guiding septal puncture , mullins sheath with side arm • should be available in 6 fr./7 fr./ 8fr. sizes , group-d3 , ptmc balloon ‘inoue type’ with accessories , ptmc balloon of ‘inoue type’ without accessories , ptmc balloon ‘inoue type’ with accessories , ptmc balloon of ‘inoue type’ without accessories- , ptmc balloon ‘inoue type’ with accessories – , ptmc balloon ‘inoue type’ without accessories – , transseptal puncture needle • infants, pediatric and adult sizes • tapering tip • standard curve • hub with angle indicator , group-d4 , asd closure devices with delivery system - • approved for pediatric/adult use • device made of biologically inert material • self-centering, detachable device with delivery cable • available in all the sizes (6 mm – 40 mm) , asd closure device without delivery system , delivery sheath for asd closure device- compatible with the device approved in item no. 27.01 , preloaded asd closure devices - • approved for pediatric/adult use • device made of biologically inert material • preloaded device with delivery cable , asd closure devices with delivery system – • device made of biologically inert material • available in all the sizes , asd closure device without delivery system , delivery sheath for asd closure device- compatible with the device approved in item no at . 27.04 , asd closure device with delivery system – • device made of biologically inert material • available in all the sizes , asd closure device without delivery system – , delivery sheath for asd closure device– compatible with the device approved in item no. at 27.08 , fenestrated asd closure devices , group-d5 , vsd closure devices with delivery system - • approved for pediatric/adult use • device made of biologically inert material • self-centering, detachable device with delivery cable • available in all the sizes , vsd closure devices without delivery system , delivery sheath for vsd closure device - compatible with the device approved in item no.at 28.01 , vsd closure devices with delivery system - • device made of biologically inert material • available in all the sizes , vsd closure devices without delivery system - , delivery sheath for vsd closure device- ce marked compatible with the device approved in item no.at28.04 , vsd closure device with delivery system – • device made of biologically inert material • available in all the sizes , vsd closure device without delivery system – delivery sheath for vsd closure device– compatible with the device approved in item no. at 28.07 , pda closure devices with delivery system - • approved for pediatric/adult use • device made of biologically inert material • self-centering, detachable device with delivery cable • available in all the sizes , group -d6 , pda closure devices without delivery system , delivery sheath for pda closure device - compatible with the device approved in item no.29.01 , pda closure devices without delivery system - • device made of biologically inert material • available in all the sizes , pda closure device without delivery system – , delivery sheath for pda closure device – compatible with the device approved in item no.at 29.04 , pda closure device with delivery system – device made of biologically inert material • available in all the sizes , pda closure device without delivery system – , delivery sheath for pda closure device- compatible with the device approved in item no. at 29.07 , group-d7 , pfo closure device with delivery system – approved for pediatric /adult usedevice made of biologically inert material • available in all the sizes , pfo closure devices without delivery system , delivery sheath for pfo closure device – compatible with the device approved in item no. at 30.01 , pfo closure devices with delivery system - • device made of biologically inert material • available in all the sizes , pfo closure devices without delivery system - , delivery sheath for pfo closure device- compatible with the device approved in item no. at 30.04 , pfo closure device with delivery system – • device made of biologically inert material • available in all the sizes , pfo closure device without delivery system , delivery sheath for pfo closure device– compatible with the device approved in item no. at 30.07 , sizing balloon for device closure – circular shape , sizing balloon for device closure – oval shaped , sizing plate for device closure , group-d8 , delivery cables for asd/vsd/pda devices , retrievers for asd/vsd/pda devices , sheath for retrival of devices , wire 0.018” regular length, regular shaft stiffness • floppy tip • straight / j shaped tip • 140-180 cm long , wire 0.018” regular length, extra- stiff shaft • floppy tip • straight / j shaped tip • 140-180 cm long , wire 0.018” exchange length, regular shaft stiffness • floppy tip • straight / j shaped tip • 240-300 cm long , wire 0.018” exchange length, extra- stiff shaft • floppy tip • straight / j shaped tip • 240-300 cm long , valvoplasty balloon catheters • varying sizes and diameters • approved for pediatric/adult use , special balloon catheter compatible with 4 french sheath • compatible with 0.018 inch guide wire • varying length and diameter , special pediatric valvoplasty balloon catheters compatible with 4 french sheath • compatible with 0.025 inch guide wire • varying length and diameter , group-d9 , valvoplasty balloon catheters (sizes 10 – 22 mm) • approved for pediatric/adult use • varying length and diameter • nominal pressure < 4 atm , balloon catheters (sizes 10 – 22 mm) • approved for pediatric/adult use • varying length and diameter • nominal pressure > 8 atm , balloon in balloon catheter • quote in all sizes , fogarty embolectomy catheter • 4fr/5fr/6 fr sizes • metal rod at tip of the catheter to enable angulations up to 60 degrees , atrial septostomy catheter • 4fr/5fr/6fr sizes , detachable balloon , vascular plugs- fda approved , vascular plugs- ce marked , vascular plugs- approved by dcgi , radiofrequency perforation accessories • compatible with beyliss system , group-d10 , pda coils made of steel • 0.035, 0.038 inches • sizes ranging from 2 x 2 to 15 x 15 , pda coils made of nitinol • 0.035, 0.038 inches • sizes ranging from 2 x 2 to 15 x 15 , pda coils made of platinum • 0.035, 0.038 inches • sizes ranging from 2 x 2 to 15 x 15 , 0.052 inch pda coils made of nitinol • sizes ranging from 2 x 2 to 15 x 15 , 0.052 inch pda coils made of platinum • sizes ranging from 2 x 2 to 15 x 15 , embolisation coils (0.018 inch) • sizes ranging from 2 x 2 to 15 x 15 , embolisation coils (0.035 inch) • sizes ranging from 2 x 2 to 15 x 15 , embolisation coils (0.052 inch) • sizes ranging from 2 x 2 to 15 x 15 , park blade septectomy catheter , group-d11 , balloon expandable pulmonary artery and aortic stents – approved for pediatric/adult use • available in various sizes , self expanding pulmonary artery and aortic stents- • approved for pediatric/adult use • available in various sizes , hydrophilic diagnostic guide wire - radifocus (regular length, regular stiffness) • must be available in 0.025, 0.032, 0.035 and 0.038 inches size • should have superelastic alloy core • should have super flexible wire tip • should be available in straight and angled tip • should be between 120-150 cm long , hydrophilic diagnostic guide wire -‘radifocus’ (exchange length, regular stiffness) • must be available in 0.025, 0.032, 0.035 and 0.038 inches size • should have superelastic alloy core • should have super flexible wire tip • should be available in straight and angled tip • should be 260 cm long , hydrophilic diagnostic guide wire - radifocus (regular length, extra-stiff) • must be available in 0.025, 0.032, 0.035 and 0.038 inches size • should have superelastic alloy core • should have super flexible wire tip • should be available in straight and angled tip o should be between 120-150 cm long , hydrophilic diagnostic guide wire - radifocus (exchange length, extra-stiff) • must be available in 0.025, 0.032, 0.035 and 0.038 inches size • should have superelastic alloy core • should have super flexible wire tip • should be available in straight and angled tip • should be 260 cm long , exchange length 0.035 inch guidewire dedicated for vsd device closure– noodle type , special introducer sheath for transseptal puncture • should include a dilator and sheath • dilator should provide smooth transition with septal puncture needle • should be available in varying sizes • radio-opaque tip marker for precise visualization of sheath • should be kink and collapse resistant • should be flexible , special long sheath with side arm having hausdorf-lock curve for asd device closure • variable lengths and sizes , special long sheaths with side arm having mullins curve, balkans curve, 180 curve and other curves • variable lengths and sizes , ptca inflation device- (maximum pressure upto 10 atm) • luminescent analog pressure gauge with maximum pressure up to 10 atm • efficient locking system to maintain high pressure • rapid inflation and deflation • clear barrel for easy visualization of de-bubbling • ergomatric and user friendly hand held design , group e -12 , disposable radiation protection pad -radial single layer, sterilized packed, non-vinyl, lead (pb)-free and light weight absorbable radial drape for protection from scattered radiation during interventional procedures like radial angioplasty, peripheral & ir etc. should have barc test certificate, and lead equivalency must be at least 0.125mmpb and attenuation shield size: 406mmx305mm mandatory document need to be submitted: • third-party environmental safety document. • clinical proof of attenuation. disposable radiation protection pad -femoral and subclavian single layer, sterilized packed, non-vinyl, lead (pb) -free and light weight absorbable femoral drape for protection from scattered radiation during interventional procedures like ep ablation, cto etc. should have barc test certificate, and lead equivalency must be at least 0.125mmpb and attenuation shield size: 406mmx305mm mandatory document need to be submitted: • third-party environmental safety document. • clinical proof of attenuation. no brainer cap non-lead single layer head cover, non-vinyl, lead (pb) -free x-ray attenuation, light weight surgical cap for radiation safety in all fluoro labs and must be fit all head sizes. should have a lead equivalency must be at least 0.125mmpb. weight should not be more than 95grams and attenuation shield size: 559mmx76mm mandatory document need to be submitted: • third-party environmental safety document. • clinical proof of attenuation , group -f1 , hydrophilic dignostic guide wire - (regular length, regular stiffness) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be available in straight and angled tip • should be between 120-180 cm long • short floppy tip 3-8 cm long , hydrophilic diagnostic guide wire - (exchange length, regular stiffness) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be available in straight and angled tip • should be 260 cm long • short floppy tip 3-8 cm long , hydrophilic diagnostic guide wire - (exchange length, regular stiffness) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be available in straight and angled tip • should be 300 cm long • short floppy tip 3-5 cm long , hydrophilic diagnostic guide wire - (regular length, extra-stiff) - • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be available in straight and angled tip • should be between 120-180 cm long • short floppy tip 3-8 cm long , hydrophilic diagnostic guide wire - (exchange length, extra-stiff) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be available in straight and angled tip • 3-5 cm long tip • should be 260 cm long , hydrophilic diagnostic guide wire - (exchange length, extra-stiff) • should be available in 0.025, 0.032, 0.035 and 0.038 inches size • should be available in straight and angled tip • 3-5 cm long tip • should be 300 cm long , ptfe coated extrastiff shaft strength wire- backup meier( regular length) • extremely stiff stainless steel shaft core • flexible short length ‘j’ shaped tip which should be highly radio-opaque . • 0.035 inches • 185 cm long , ptfe coated extra stiff shaft strength exchange wire- backup meier (exchange length) • extremely stiff stainless steel shaft core • flexible short length ‘c’ shaped tip which should be highly radio-opaque . • 0.035 inches • 300 cm long , nitinol 0.014 inch guidewire (exchange length)straight and angled • with hydrophilic coating • 260-300 cm long • with and without flexible tip , nitinol 0.018 inch guidewire (exchange length) • straight and angled • with hydrophilic coating • 260-300 cm long • with and without flexible tip , group -f 2 , heavy duty nitinol alloy extra support wire ( regular length) • 0.014 inches • nitinol alloy • with angled tip-3-5 cm long • tip with platinum/platinum alloy for optimum visualisation • with tfe coating • 180 cm long , heavy duty nitinol alloy extra support wire (exchange length) • 0.014 inches • nitinol alloy • with angled tip-3-5 cm long • tip with platinum/platinum alloy for optimum visualisation • with tfe coating • 270-300 cm long , heavy duty nitinol extra support wire( regular length) • 0.018 inches • nitinol alloy • with angled tip-3-5 cm long • tip with platinum/platinum alloy for optimum visualization • with tfe coating • 180 cm long , heavy duty nitinol extra support wire (exchange length) • 0.018 inches • nitinol alloy • with angled tip: 3-5 cm long • tip with platinum/platinum alloy for optimum visualisation • with tfe coating • 270-300 cm long , steerable high support .014 inch guidewire • ptfe/duraglide coated • distal radiopaque tip 3 cm long • straight and j curve • 180cm long , steerable high support .014 inch guide wire ( exchange) • ptfe/duraglide coated • distal radiopaque tip 3 cm long • straight and j curve • 260-300cm long , cobra catheter • 4french/5french/6french • 65-125 cm long • 021-038 compatible • in various standard curves . , sos omni catheter • 035-038 compatible • 80 cm long , tapered straight catheter • 4french/5french/6french • 70,100 cm long • .035 inch compatible , picard catheter • 4french/5french/6french • 035-038 compatible • in various standard lengths. , group -f3 , renal double curve catheter • in various standard lengths and curves , head hunter catheter • in various standard lengths and curves • 035-038 compatible • 100cm long , simmons/ sidewinder catheter • in various standard lengths and curves • 035-038 compatible • 100cm long , pre -shaped catheter for uterine artery embolisation • in various standard lengths and curves , vertebral catheter • in various standard lengths and curves , coeliac axis catheter • in various standard lengths and curves , shepherd’s hook catheter • in various standard lengths and curves , micro catheters (coiled stainless steel construction) • in various standard lengths and curves • 2-3.8f size • .010-.022 inch wire compatible • with radioopaque marker at tip , micro catheters (braided nitinol construction) • in various standard lengths and curves • 2-3.8f size • .010-.022 inch wire compatible • with radioopaque marker at tip , straight introducer sheath (standard length) with hydro philic introducer guide wire • sizes from 4french/5french/ 6 french/7 french/8frenc/9french • between 7-11 cm long • with 0.035 or 0.038 inch hydrophilic mini guide wire • with plastic cannula for arterial puncture , group -f4 , straight long introducer sheath with hydrophilic introducer guide wire • sizes from 4french/5french/ 6 french/7 french/8frenc/9french • 16 cm long • with 0.035 or 0.038 inch hydrophilic guide wire • with plastic cannula for arterial puncture , straight reinforced sheath with hydrophilic coating • sizes from 6french /7french /8frenc/9french/10french/11french • between 7-11 cm long • with 0.035 or 0.038 inch guide wire compatible • with radio-opaque tip , group -f5 , guiding catheter for peripheral vascular use – – should be braided with low friction inner layer - should have atraumatic soft tip - should be available in various tip shapes and curves for access to different parts of the peripheral vasculature, including renal double curve, cobra, multi-purpose and other shapes - should have od of 6f-8f available - should have the largest id for each od - should have lengths ranging from 55-90 cm , guiding catheter for peripheral vascular use – – should be braided with low friction inner layer - should have hydrophilic coating - should have atraumatic soft tip - should be available in various tip shapes and curves for access to different parts of the peripheral vasculature. - should have od of 6f-10f available - should have the largest id for each od - should have lengths ranging from 55-125 cm , guiding catheter for peripheral vascular use – – should be braided with low friction inner layer - should have hydrophilic coating - should have atraumatic soft tip - should be available in various tip shapes and curves for access to different parts of the peripheral vasculature. - should have od of 5f available with the largest od - should have a minimum length of 55 cm or more , long sheath for peripheral vascular access– - should be kink resistant with a reinforcement mechanism - should be low friction with inner coating to allow catheter manipulation - should have distal radio-opaque tip for enhanced visibility on fluoroscopy - should have smooth transition from dilator to sheath - should have a proximal hemostasis valve/provision for tuohyborst valve - should be color coded for size identification - should be available in various sizes of inner diameters and various lengths and have the largest id available , long sheath for carotid access – - should be kink resistant with a reinforcement mechanism - should be low friction with inner coating to allow catheter manipulation - should have distal radio-opaque tip for enhanced visibility on fluoroscopy - should have smooth transition from dilator to sheath - should have a proximal hemostasis valve/provision for tuohyborst valve - should be color coded for size identification - should be available in 4f-8f size with the largest id - should have a minimum length of 90 cm or more , long sheath for contra-lateral iliac/femoral access – - should be kink resistant with a reinforcement mechanism - should be low friction with inner coating to allow catheter manipulation - should have distal radio-opaque tip for enhanced visibility on fluoroscopy - should have smooth transition from dilator to sheath - should have a proximal hemostasis valve/provision for tuohyborst valve - should be color coded for size identification - should be available in 4f-9f size with the largest id - should have lengths ranging from 40- 110 cm , group -f6 , long sheath for renal access – - should be kink resistant - should be low friction with inner coating to allow catheter manipulation - should have distal radio-opaque tip for enhanced visibility on fluoroscopy - should have smooth transition from dilator to sheath - should have a proximal hemostasis valve/provision for tuohyborst valve - should be color coded for size identification - should be available in 5f-7f size with the largest id - should be at least 55 cm long , high pressure angioplasty balloon for peripheral vascular use – - should have rated burst pressure > 14 atmosphere - should have hydrophilic coating - should be available in various outer diameters and balloon lengths and various shaft lengths , high pressure angioplasty balloon for peripheral vascular use – - should have rated burst pressure > 14 atmosphere - should have hydrophilic coating - should be available in various outer diameters and balloon lengths , high pressure angioplasty balloon for peripheral vascular use – - should have rated burst pressure > 14 atmosphere - should have hydrophilic coating - should be available in various outer diameters and balloon lengths - should be available in various shaft lengths , high pressure angioplasty balloon for peripheral vascular use – - should have rated burst pressure > 14 atmosphere - should have hydrophilic coating - should be available in 4-10 mm (in 1 mm increments) and 12 mm diameters and 2-10 cm balloon length - should have a shaft size of 75-135 cm , high pressure angioplasty balloon for peripheral vascular use– - should have rated burst pressure > 14 atmosphere - should have hydrophilic coating - should be available in 4-12 mm diameter and 2-10 cm balloon length - should have a shaft size of 75-135 cm , high pressure angioplasty balloon for peripheral vascular use– - should have rated burst pressure > 14 atmosphere - should have hydrophilic coating - should be available in 4-12 mm diameter and 2-10 cm balloon length - should have a shaft size of 75-135 cm , peripheral balloon catheter – - should be 0.035” compatible - should be over the wire - should have a burst pressure of at least 10 atmosphere (at least 6 atmosphere for larger balloons) - should have hydrophilic coating - should be available in various sizes of od and balloon lengths - should be available in various shaft lengths , peripheral balloon catheter – - should be 0.035” compatible - should be over the wire - should be non-compliant or semi-compliant - should have hydrophilic coating - should be available in all ods of 3-10 mm and 12 mm and balloon length of 2-10 cm. - should have burst pressure of at least 10 atmosphere (the 12 mm od balloon should have a burst pressureof at least 6 atmosphere) - should pass through a maximum 6f sheath (the 12 mm od balloon should pass through a maximum 7fsheath) - should have a shaft length 80-135 cm , group -f7 , peripheral balloon catheter – - should be 0.035” compatible - should be over the wire - should have a burst pressure of at least 10 atmosphere (at least 6 atmosphere for larger balloons) - should have hydrophilic coating - should be available in various sizes of od and balloon lengths - should be available in various shaft lengths , peripheral balloon catheter – - should be 0.035” compatible - should be over the wire - should be non-compliant or semi-compliant - should have hydrophilic coating - should be available in od of 3-10 mm and 12 mm and balloon length of 2-10 cm. - should have burst pressure of at least 10 atmosphere (the 12 mm od balloon should have a burst pressureof at least 6 atmosphere) - should pass through a maximum 6f sheath (the 12 mm od balloon should pass through a maximum 7fsheath) - should have a shaft length 80-135 cm , peripheral balloon catheter – - should be 0.035” compatible - should be over the wire - should have a burst pressure of at least 10 atmosphere (at least 6 atmosphere for larger balloons) - should have hydrophilic coating - should be available in various sizes of od and balloon lengths - should be available in various shaft lengths , peripheral balloon catheter – - should be 0.035” compatible - should be over the wire - should be non-compliant or semi-compliant - should have hydrophilic coating - should be available in all ods of 3-10 mm and 12 mm and balloon length of 2-10 cm. - should have burst pressure of at least 10 atmosphere (the 12 mm od balloon should have a burst pressureof at least 6 atmosphere) - should pass through a maximum 6f sheath (the 12 mm od balloon should pass through a maximum 7fsheath) - should have a shaft length 80-135 cm , peripheral balloon catheter with large diameter - should be 035” compatible - should be over the wire - should have hydrophilic coating - should have od of 14 mm and more - various lengths of the balloon should be available - should be mounted on various shaft lengths , peripheral balloon catheter with large diameter – - should be 035” compatible - should be over the wire - should have hydrophilic coating - should an od of at least 14 mm - various lengths of the balloon should be available - should be mounted on various shaft lengths , peripheral balloon catheter with large diameter – - should be 035” compatible - should be over the wire - should have hydrophilic coating - should an od of at least 14 mm - various lengths of the balloon should be available - should be mounted on various shaft lengths , peripheral balloon catheter – - should be .014/.018” compatible - should be over the wire - should have hydrophilic coating - should be available in various balloon diameters - should be available in various lengths of the balloon - should be available in various shaft lengths , group -f9 , peripheral compliant balloon with large diameter – - should be .035” compatible - should have od ranging from 10-46 mm - should have shaft length >90 cm - should have shaft of not more than 8f size - should pass through a 12f sheath , peripheral stent balloon mounted – - should be .014/.018” compatible - should be over the wire - should be made of stainless steel alloy - should have balloon od in the range of 4-7 mm - should have balloon/stent lengths in the range of 12-25 mm - should have shaft lengths of 80-150 cm , peripheral stent balloon expandable – - should be .014/.018” compatible - should be over the wire - should be made of stainless steel alloy - should have balloon od in the range of 4-7 mm - should have balloon/stent lengths in the range of 12-25 mm - should have shaft lengths of 80-150 cm , group -f10 , peripheral stent balloon expandable - - should be .014/.018” compatible - should be for rapid exchange - should be made of stainless steel alloy - should have balloon od in the range of 4-7 mm - should have balloon/stent lengths in the range of 12-25 mm - should have shaft lengths of 80-150 cm , peripheral stent balloon expandable – - should be 035” compatible - should be made of stainless steel or cobalt chromium - should be quoted either in open cell or closed cell design - should be available in various balloon ods - should have various balloon/stent lengths available - should have a shaft length of 75-135 cm , peripheral stent balloon mounted – - should be 035” compatible - should be made of stainless steel or cobalt chromium - should be quoted either in open cell or closed cell design - should be available in various balloon ods - should have various balloon/stent lengths available - should have a shaft length of 75-135 cm , peripheral stent balloon expandable – - should be .035” compatible - should be made of stainless steel or cobalt chromium - should be quoted either in open cell or closed cell design - should be available in various balloon ods - should have various balloon/stent lengths available - should have a shaft length of 75-135 cm , peripheral stent balloon expandable – - should be .035” compatible - should be made of stainless steel - should have a tandem architecture design - should have all balloon ods from 5-10 mm in 1 mm increments - should have available various balloon/stent lengths of 20 to 55mm - should have a shaft length of 75 -135 cm , peripheral stent balloon expandable – - should be .035” compatible - should be made of stainless steel - should have a tandem architecture design - should have all balloon ods from 5-10 mm in 1 mm increments - should have available various balloon/stent lengths from 20 to 55 mm - should have a shaft length of 75 -135 cm , peripheral stent balloon expandable - should be .035” compatible - should be made of stainless steel - should have a tandem architecture design - should have all balloon ods from 5-10 mm in 1 mm increments - should have available various balloon/stent lengths from 20 to 55 mm - should have a shaft length of 75 -135 cm , peripheral stent balloon expandable – - should be .035” compatible - should be made of stainless steel - should be laser cut slotted tube with closed cell design - should have balloon ods from 5-25 mm, bare or balloon mounted - should have available various balloon stent/lengths from 2-6 cm - should have a shaft length of up to 135 cm , peripheral stent balloon expandable – - should be .035” compatible - should be made of stainless steel - should be laser cut slotted tube with closed cell design - should have balloon ods from 5-25 mm, bare or balloon mounted - should have available various balloon stent/lengths from 2-6 cm - should have a shaft length of up to 135 cm , peripheral stent balloon expandable – - should be .035” compatible - should be made of stainless steel - should be laser cut slotted tube with closed cell design - should have balloon ods from 5-25 mm, bare or balloon mounted - should have available various balloon stent/lengths from 2-6 cm - should have a shaft length of up to 135 cm , group- f11 , self-expanding peripheral stent – - should be .014/018” compatible - should be over the wire - should be made of nitinol - should have the least lesion crossing profile for all stent diameters - should be available in various stent diameters of 6-10 mm - should be available in various stent lengths from 20-40 mm - should have a shaft length of at least 110 cm , self-expanding peripheral stent – - should be .014/.018” compatible - should be over the wire - should be made of nitinol - should have the least lesion crossing profile for all stent diameters - should be available in various stent diameters of 6-10 mm - should be available in various stent lengths from 20-40 mm - should have a shaft length of at least 110 cm , self-expanding peripheral stent – - should be .014/.018” compatible - should be over the wire - should be made of nitinol - should have the least lesion crossing profile for all stent diameters - should be available in various stent diameters of 6-10 mm - should be available in various stent lengths from 20-40 mm - should have a shaft length of at least 110 cm , self-expanding peripheral stent – - should be .014/.018” compatible - should be over the wire - should be laser cut open cell nitinol tube - should have a low lesion crossing profile - should be available in all stent diameters of 6-10 mm - should be available in stent lengths of 2-6 cm - should be on a shaft length of 110-140 cm , self-expanding peripheral stent – - should be .014/.018” compatible - should be over the wire - should be laser cut open cell nitinol tube - should have a low lesion crossing profile - should be available in all stent diameters of 6-10 mm - should be available in stent lengths of 2-6 cm - should be on a shaft length of 110-140 cm , self-expanding peripheral stent – - should be .014/.018” compatible - should be over the wire - should be laser cut open cell nitinol tube - should have a low lesion crossing profile - should be available in all stent diameters of 6-10 mm - should be available in stent lengths of 2-6 cm - should be on a shaft length of 110-140 cm , self expanding peripheral stent – - should be .014/.018” compatible - should be of rapid exchange type - should be made of nitinol - should be available in stent lengths of 3-4 cm - should have a minimum shaft length of 110 cm , self expanding peripheral stent – - should be .014/.018” compatible - should be of rapid exchange type - should be made of nitinol - should be available in stent lengths of 3-4 cm - should have a minimum shaft length of 110 cm , self expanding peripheral stent – - should be .014/.018” compatible - should be of rapid exchange type - should be made of nitinol - should be available in stent lengths of 3-4 cm - should have a minimum shaft length of 110 cm , self-expanding peripheral stent – - should be .035” compatible - should be over the wire - should be made of nitinol - should be available in various outer diameters - should be of various stent lengths - should be on a shaft length of 80-140 cm , group -f12 , self-expanding peripheral stent – - should be .035” compatible - should be over the wire - should be made of nitinol - should be available in various outer diameters - should be of various stent lengths - should be on a shaft length of 80-140 cm , self-expanding peripheral stent – - should be .035” compatible - should be over the wire - should be made of nitinol - should be available in various outer diameters - should be of various stent lengths - should be on a shaft length of 80-140 cm , self-expanding peripheral stent – - should be .035” compatible - should be over the wire - should be laser cut from single nitinol tube with no welds - should be available in outer diameters of 5-14 mm - should be available in stent lengths of 2-15 cm - should be on a shaft length of 80-140 cm - should be available in various lengths of 20-100 mm , peripheral bio-degradable or absorbable metal stent - should be balloon mounted or self-expanding type - should be available in outer diameters of 4-8 mm - should be available in various lengths of 20-100 mm , group -f13 , dedicated peripheral vascular bifurcation stent - should be balloon mounted - should be available in different diameters and lengths of the stent , self expanding peripheral covered stents – - should be .035” compatible - should be over the wire - should be made of nitinol with fabric coating - should be available in various outer diameters - should be available in various stent lengths - should be on a shaft length of 80-140 cm. , self expanding peripheral covered stents – - should be .035” compatible - should be over the wire - should be made of nitinol with fabric coating - should be available in various outer diameters - should be available in various stent lengths - should be on a shaft length of 80-140 cm , self expanding peripheral covered stents – - should be .035” compatible - should be over the wire - should be made of nitinol with fabric coating - should be available in various outer diameters - should be available in various stent lengths - should be on a shaft length of 80-140 cm. , self expanding peripheral covered stents – - should be .035” compatible - should be over the wire - should be made of nitinol with ptfe coating on the inner lumen - should be available in outer diameters of 5-13 mm - should be avaiable in stent lengths of 2-15 cm - should be on a shaft length of 75-140 cm. , self expanding peripheral covered stents – - should be .035” compatible - should be over the wire - should be made of nitinol with ptfe coating on the inner lumen - should be available in outer diameters of 5-13 mm - should be avaiable in stent lengths of 2-15 cm - should be on a shaft length of 75-140 cm. , self expanding peripheral covered stents - should be .035” compatible - should be over the wire - should be made of nitinol with ptfe coating on the inner lumen - should be available in outer diameters of 5-13 mm - should be avaiable in stent lengths of 2-15 cm - should be on a shaft length of 75-140 cm. , covered stent for transjugular intrahepatic porto-systemic shunt - should be .035/038” compatible - should be made of nitinol with fabric coating - should be with or without a distal uncovered portion - should be available in various outer diameters and stent lengths - should be compatible with the quoted tips set , covered stent for transjugular intrahepatic porto-systemic shunt - should be .035/038” compatible - should be made of nitinol with ptfe coating on inner lumen - should be with a distal at least 2 cm uncovered portion - should be available in all outer diameters of 8,10,12 mm - should be available in all stent lengths of 4,5,6,7,8 cm - the delivery system should be at least 75 cm long - should be compatible with the quoted tips set , embolisation coils - should be .014/018” compatible - should be made of platinum with synthetic fibres - should be non tapering/straight - should be mr compatible - should be available in any or more of the following diameters: 2-10 mm - should be of various lengths; the length of the coil at each diameter should be stated , group- f14 , embolisation coils -should be .014/018” compatible - should be made of platinum with synthetic fibres - should be mr compatible - should taper from a larger to a smaller end - should be available in any or more of the following diameters: 3-10 mm - the diameter to tapered end for tapering type coils should be stated - should be of various lengths; the length of the coil at each diameter should be stated , embolisation coils - should be .035/038” compatible - should be non tapering/straight - should be made of platinum with synthetic fibres - should be mr compatible - should be available in the following sizes: diameter 3-15 mm and length 2-15 cm , embolisation coils - should be .035/038” compatible - should be made of platinum with synthetic fibres - should be mr compatible - should be tapering from a larger to a smaller end - should be available in following sizes: diameter 5-10 mm and length 2-15 cm - the diameter to tapered end for tapering type coils should be mentioned , embolisation coils - should be .035/038/052” compatible - should be non tapering/straight - should be made of stainless steel with synthetic fibres - should be available in the following sizes: diameter 3-15 mm and length 2-15 cm , coil pusher wire for 0.014/0.018” coils, compatible with the quoted microcatheters , polyvinyl alcohol particles for peripheral vascular embolization - should be of non-uniform size - should undergo rapid clumping in the vessels - should cause non-uniform vessel occlusion - should be available in a broad range of sizes (90 microns- 1400 microns) , microspheres for peripheral vascular embolization - should be hydrophilic - should be micro-porous and uniform sized spheres - should be non-aggregating - should be deformable for ease of passage through smaller vessels - the size of spheres should range from40-1200 micrometers , gelfoam sheet for vascular embolization , non-adhesive liquid polymer for controlled embolization - should be ethylene vinyl copolymer in dimethylsulfoxide solution - should be supplied in various concentrations for use depending on lesion morphology , adhesive liquid polymer for vascular embolization - should be n-butyl cyanoacrylate , group -f15 , tantalum powder -should be useful for improved visualization during n-butyl cyanoacrylate embolization - should be supplied as finely ground powder , lipiodol - the material should be iodised oil, containing ethyl esters of iodized fatty acids of poppy seed oil - the iodine content should be a minimum of 480 mg/ml - should useful as opacifying agent for n-butyl cyanoacrylate on fluoroscopy and an organic diluent for thisagent - should be supplied in 10 ml ampoules , sclerosant for intravenous embolization - the compound should be sodium tetradecyl sulfate - should be available in various concentrations for use depending on lesion type , sclerosant for intravenous embolization - the compound should be aetoxisclerol - should be available in various concentrations for use depending on lesion type , medical grade ethanolamine oleate for vascular embolization , detachable balloon for embolization - detachable balloons with radioopaque marker with and without self-sealing valve - 0.1 cc – 3 cc or more in capacity - please specify the make and capacity of the balloons (latex/silicon). - the catheter shaft should be of at least 120 cm in length , transjugular liver biopsy set - should include angled tip needle advanced through percutaneously introduced liver access set - should have a firing spring mechanism - needle gauge should be available in 18 and 19g and needle length should be 45-60 cm - the needle throw distance should be not more than 2 cm - should include the check-flo valve adapter, stiffening cannula curved and straight catheter and introducer sheath (upto 7f size) , transjugular intrahepatic porto-systemic shunt access set - should include a micropuncture introducer set -should include an introducer sheath that should be no more than 10f size, at least 38 cm long and 035/038”compatible - the sheath should provide maximum flexibility without getting kinked - the sheath should have proximal check flo mechanism - the sheath should have distal radiopaque tip to indicate sheath tip on fluoroscopy - the set should also include a needle of 16g and at least 50 cm long with angled tip to facilitate directiontowards portal vein - there should be a curved/angled catheter, a straight catheter and a centimeter sizing catheter incorporated in the set for the various steps of the procedure , transjugular liver access set (10f) for various diagnostic and interventional liver procedures - should include a 10f and at least 38 cm long introducer sheath - should include a stiffening cannula of at least 14 gauge and length of at least 51 cm - should include a trochar with stylet that is 035/038” compatible and at least 60 cm long , transjugular liver access set (7-9f) for various diagnostic and interventional liver procedures - should include a 7f or 9f introducer sheath that is at least 38 cm long - should include needle with angled tip that is 16f (for 9f) and 18g (for 7f) sheath - should be 035/038” compatible - the needle shoud be at least 50 cm long , group -f16 , ivc filter - for optimal filtration of ivc diameter of upto 40 mm - made of either nitinol or stainless steel - catheter carrier system inner diameter should be of maximum 12f - it should be possible to insert from either jugular or femoral access - should be for permanent use , ivc filter - for optimal filtration of ivc diameter of upto 28 mm - made of nitinol and filter length to be upto 38 mm - catheter carrier system inner diameter should be of maximum 7f size - it should be for permanent use - it should be possible to place the filter from femoral/jugular/antecubital access , ivc filter - for optimal filtration of ivc diameter of upto 28 mm - made of nitinol and filter length to be upto 55 mm - catheter carrier system inner diameter should be of maximum 10 f size - it should be for optional (permanent or retrievable) use - it should be possible to place the filter from femoral/jugular/antecubital access , ivc filter - for optimal filtration of ivc diameter of upto 30 mm - made of conichrome material and filter length not more than 50 mm - should be able to be placed either through jugular or femoral approach - should be for optional (permanent or temporary) use , percutaneous mechanical thrombectomy catheter - should allow treatment of fresh and older thrombotic occlusions of peripheral arteries - should combines mechanical fragmentation and aspiration alongwith transport of debris outside thevascular system - should be available in both antegrade or cross-over configurations - for antegrade access – maximum shaft size should be 6f - for cross-over access – maximum shaft size should be 8f , urokinase for intra-arterial thrombolysis , tissue plasminogen activator for intra-arterial thrombolysis , infusion catheter - should have multiple side ports - should provide an infusion length of 5-15 cm - should have a catheter tip occluder - should have attachment for tuohy-borst side arm adapter - should have a maximum od of 5f - should be compatible with 035/038” wire - should have a shaft length of 60-100 cm , distal embolic protection device - should be on a .014” wire - should be made of nitinol material - should not occlude flow while in placement - should completely cover the vessel circumference at the desired placement site to afford complete protection - should have the least lesion crossing profile - should be available in various sizes for adapting to the vessel size , distal embolic protection device - should be on a .014” wire - should be made of nitinol material - should not occlude flow while in placement - should be rapid exchange type - should allow use of a separate .014/018” wire for initial crossing of the lesion - should be compatible with a 6f guiding catheter (0.066” id) - should allow longitudinal wire movement with filter remaining in place - should be available in 3-7 mm sizes , group -f17 , endovascular stent graft device for treatment of thoracic aortic aneurysms and dissections - device should be with proximal barbs, with or without distal bare spring configuration, and should beeither tapered or non-tapered. - the aortic device should be available in any one or more of the following sizes: od 26-44 mm; length 4-24 cm. the device should be able to be advanced on upto 24f shaft size. - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ctangiography , endovascular stent graft device for treatment of thoracic aortic aneurysms and dissections - device should be without proximal barbs, without distal bare spring configuration, and should be eithertapered or non-tapered. - the aortic device should be available in any one or more of the following sizes: od 26-44 mm; length 4-24 cm. the device should be able to be advanced on upto 24f shaft size. - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ct angiography , endovascular stent graft device for treatment of thoracic aortic aneurysms and dissection - device should be without proximal barbs, with distal and/or proximal bare spring configurations, andshould be non-tapered. - the aortic device should be available in any one or more of the following sizes: od 26-44 mm; length 4-24 cm. the device should be able to be advanced on up to 24f shaft size. - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ct angiography , endovascular stent graft device for treatment of thoracic aortic aneurysms and dissection - device should be without proximal barbs, with distal and/or proximal bare spring configurations, andshould be tapered. - the aortic device should be available in any one or more of the following sizes: od 12-44 mm; length 4-24 cm. the device should be able to be advanced on upto 24f shaft size. - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ct angiography , endovascular stent graft device for treatment of abdominal aortic aneurysms - device should be with or without proximal barbs, with or without distal bare spring configuration, andshould be either tapered or non-tapered. - devices with or without transrenal or suprarenal fixation should be quoted. - the aortic device should be available in any one or more of the following sizes: od 12-44 mm; length 4-24 cm. the device should be able to be advanced on aupto 24f shaft size. - the limb extensions of the main device for abdominal aortic applications should be available in 12-22 mmdiameter, with or without flared ends and upto 12 cm in length - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ctangiography , endovascular stent graft device for treatment of abdominal aortic aneurysms - device should be with proximal barbs, with or without distal bare spring configuration, and should beeither tapered or non-tapered. - devices with transrenal or suprarenal fixation should be quoted. - the aortic device should be available in any one or more of the following sizes: od 12-44 mm; length 4-24 cm. the device should be able to be advanced on aupto 24f shaft size. - the limb extensions of the main device for abdominal aortic applications should be available in 12-22 mmdiameter, with or without flared ends and upto 12 cm in length - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ctangiography , endovascular stent graft device for treatment of abdominal aortic aneurysms - device should be without proximal barbs, with or without distal bare spring configuration, and should beeither tapered or non-tapered. - devices with transrenal or suprarenal fixation should be quoted. - the aortic device should be available in any one or more of the following sizes: od 12-44 mm; length 4-24 cm. the device should be able to be advanced on aupto 24f shaft size. - the limb extensions of the main device for abdominal aortic applications should be available in 12-22 mmdiameter, with or without flared ends and upto 12 cm in length -the manufacturer should agree to supply the size customized to the patient’s anatomy based on ct angiography , endovascular stent graft device for treatment of abdominal aortic aneurysms - device should be without proximal barbs, with or without distal bare spring configuration, and should beeither tapered or non-tapered. - devices without transrenal fixation should be quoted. - the aortic device should be available in any one or more of the following sizes: od 12-44 mm; length 4-24 cm. the device should be able to be advanced on aupto 24f shaft size. - the limb extensions of the main device for abdominal aortic applications should be available in 12-22 mmdiameter, with or without flared ends and upto 12 cm in length - the manufacturer should agree to supply the size customized to the patient’s anatomy based on ctangiography covered stent-graft (extender or iliac or contralateral limb) in diameters ranging from 12-22 mm and lengths ranging from 30-110 mm for over-the-wire delivery , peripheral vascular catheter for excision of artheroma- should have high rotation speed of the cutting mechanism without causing any trauma to the vessel – , group -g1 , permanent pacemakers with all leads and accessories • ssir, • all single chamber modes and basic pacing programmable parameters. • must have ventricular capture management • the size of lead must be 7 f or less. • the lead must be steroid eluting and should be both bipolar and unipolar configuration. • must have both active and passive fixation endocardial leads available. • life term replacement warranty • direct presence of parent company in india (not only through the distributors) and company mustprovide its trained technical person for each implantation when ever required and for follow upprogramming when it is required. • company must provide at least one programmer exclusively to the cardiology department. • company must quote only the latest model of devices commercially available department. , group -h1 -temporary pacing leads , temporary pacing leads (fda approved) , temporary pacing leads (ce approved) , temporary pacing leads (dcgi approved) , temporary pacing lead: woven interweaved, braided , temporary pacing leads: balloon floatable , bipolar catheter with central lumen038 wire compatible, variable length. , screw - in bipolar temporary pacing lead = 65 cm , temporary lead for internal cardio version , group -h1 -a long sheaths /introducers , long sheaths /introducers-prefaced valved long sheaths for rfa with mullins curve, multipurpose curve, other curves, 7f to 9f, at least 80- cm long, 0.038 wire compatible , long sheaths /introducers-bidirectonal, steerable long sheaths with variablereach, autolock , long sheaths /introducers-brite tip intervention sheath with tip visualization, kink resistant, cold shape able with silicon coating , long sheaths /introducers-introducer sheaths for electrophysiology, with various swartz curves sl 0-4, sr 0-4, 8f, 8.5f,9f , long sheaths /introducers-long sheaths (peel away, slit table, with breakable valve) for special applications like coronary sinus intubation, lateral vein. special curves like renal, hook shape etc , long sheaths /introducers-peel away introducer sheaths with break away hemostatic valves for pacing leads, 5f-12f, 10 cm – 30 cm, optional infusion side port, radio opaque edistal tip and multiple curves , long sheaths /introducers-multiport catheter introducer sheaths , long sheaths /introducers-pacing lead stabilizers , long sheaths /introducers-3-d braided steerable guiding introducer sheath, supporting transseptal crossing, atrial ablation procedures, with one device delivery system having all 8 steering curves (sl and sr), can accommodate multiple sheath sizes , group -h2 (diagnostic ep catheters) the vendor should quote for each catheter separately if prices differ based upon french size, curve,electrode catheter design (electrode size, electrode distance, electrode material) etc. it will be easier if the common catheters used like 6f, josephson curve, electrode configuration 2-5-2-5, stainless steelelectrodes/platinum electrodes are specified first. all cables should be quoted separately. cost mentioned for each item will be compared based on the catheter and cable. must be compatible to st jude ensite precision , quadripolar 6, any , quadripolar 5-7, mullins , quadripolar 5-7, josephson , quadripolar 5-7, his bundle , quadripolar 5-7 4-2, mullins , quadripolar 6, mullins , tripolar 5-7, any , tripolar 6, josephson , hexapolar 6, any , decapolar 5-7, any , decapolar 6, any , decapolar 5-7, any, 2-5-2 , decapolar 5-7, any, 2-2-2 , decapolar 5-7, any, 2-2-2-10-2-2-2-10-2 , ep cathters for pediatric ep work -quadripolar 4 2-5-2- , ep cathters for pediatric ep work -quadripolar 4 , ep cathters for pediatric ep work -decapolar 4 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) - , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -quadripolar 6 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -quadripolar 5-7 2-5 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -quadripolar 5 -7 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -quadripolar5 -7 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -hexapolar 6 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -decapolar 6 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -decapolar 5 -7 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -decapolar 5 -7 , woven ep diagnostic catheters (woven material with braided conducting wire, ensuring prolonged stability) -decapolar 5 -7 , woven pediatric ep catheters (woven material with braided conducting wire, ensuring prolonged stability) - , woven pediatric ep catheters (woven material with braided conducting wire, ensuring prolonged stability) -quadripolar 4 , woven pediatric ep catheters (woven material with braided conducting wire, ensuring prolonged stability) -quadripolar 4 , woven pediatric ep catheters (woven material with braided conducting wire, ensuring prolonged stability) -decapolar 4 , group –h3 [special catheters for af, flutter, etc(quote all diameters, french size, different electrodes like platinum or stainless steel)] , deflect decaduapolar (20 poles) for a flutter----all diameters , deflectable decapolar (10)(pulm. vein)---all diameters , deflectable decaduapolar (20) (pulm. vein)—all diameters , 2f multipolar (> ten electrodes) for mapping through coronary vasculature , basket catheter with accessory , crista catheter with accessories , other special ep catheters , pacing catheter with angiographic capability • variable sizes • bipolar or quadripolar with appropriate cable • cvp monitoring & angiographic facility , paediatric use: all the above catheters, sheaths, etc, for paediatric use - implying smaller french size like 4f,5f, with certification for use in children , group -h4 (ablation catheters) - (all sizes 4f to 8.5f, all curves a-k, 270, all electrode sizes and spacing, eg.) (all items differing in make/prices need to be mentioned separately. quote separately if different in terms of material, braiding, electrode material platinum or stainless steel etc) quote with appropriate connector to existing ept 1000 and stockert ablators. ept 1000 is not compatible with thermocouple and appropriate catheters/ connectors should be quoted. thermistor catheters would therefore by preferred. in addition give prices of all connector cables /accessories separately. , regular 4mm all , regular 8mm , regular 3.5mm all , regular 8mm , regular 4mm , cool tip (closed) any , irrigated tip (open) any , others any , bidirectional any , omnidirexnl any , group -h5 (catheters, cables, accessories, for carto system and thermocool infusion pump) , navistar catheters regular , navistar catheter irrigated tip , location patch carto system (refstar) , connecting cables for all catheters , access/tubings for cool flow pump and any other accessories , group -h5-a catheters, cables, accessories for endocardial solutions (esi) accessories , navex patches , balloon array , other accessories (quote each separately) , catheters/accessories for loca lisa , reusable defibrillation/transcutaneous pacing patches (suitable for equipment in cath lab, ct2, ct3, ct6) , disposable defibrillation/transcutaneous pacing patches (suitable for equipment in cath lab, ct2, ct3, ct6) , defibrillation/transcutaneous pacing patches for use in infants and children , cryo catheters (and accessories) for ablation of arrhythmias in children and adults , intra cardiac ultrasound/echo catheter for guiding rfa compatible with the existing echo machine at neigrihms (quote all prices of the catheters and accessories) , disposable electrocautery patches for rfa (suitable for stockert and ept 1000 ablators) reusable electrocautery patches for rfa (suitable for stockert and ept 1000 ablators) electrocautery pencils for use in dissection , electrocautery pencils for use in dissection , group -h6 (pacemaker lead extraction systems -mention each system price and also individual accessories) , laser guided lead extraction system with accessories (fda/ce certified) , rf guided lead extraction system with accessories (fda/ce certified) , other extraction systems (fda/ce approved) , accessories for lead extraction like locking stylet, other accessories , intracardiac echocardiographic (ice) catheter , lead locking device for lead extraction with sizing from 0.38mm to 0.58mm compatible with any make &all range of leads, with radiopaque marker at the tip, and a proximal connector and mandrel to deploy the device. , mechanical dilator sheath, with bi-directional rotating 574 degree, while extending the blade just 0.02 inches, with flexible shaft and a static outer shaft. , otherspecific items for advanced cardiac procedure , balloon - expanding type of tavi (transcatheter aortic valve implantation) with all standard accessories for implantation different sizes.available sizes:20mm,21.5mm,23mm,24.5mm,26mm,27.5mm,29mm,30.5mm,32mm , sirolimus eluting bioresorbable coronary vascular scaffold system having various diamter and length of upto 40mm , coronary intravascular lithotripsy catheter system with foot peddel . sizes available 2.5mm, 2.75 mm ,3.0mm,3.5mm& 4.0mmand length 12mm , ptca balloon (semi-compliant) - • monorail (rapid exchange) and over-the-wire (otw) balloons • available in all sizes and lengths

Related Searched Keywords : silicon gel

List of silicon-gel Tenders

Get silicon gel Tender Alert...

Related Searched Keywords : silicon gel

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us