Filters

List of stone-chips Tenders

List of latest stone-chips Tenders in Indian Tenders. Click on any stone-chips Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for stone-chips Tenders.

All-Tenders (66)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Government Departments

TRN :49054035 | 02 Jun, 2025

Tender Value : 49.84 Lacs

Aizawl - Mizoram

Tender for supply and stacking of stone chips 13.20 mm, stone chips 11.20 mm, stone chips 6.70 mm and sand at km 100 (hmp site) on sairang-tuipuibari road for re-surfacing work approved for fy 2025-26 under 74 rcc/24 brtf of project pushpak in mizoram state , material for re-surfacing works (10.620 km cl-9) on sairang-tuipuibari road (to be supplied at km 100.00 on s-t road) , supply and stacking of stone chips of size 13.20 mm for bm 75 mm thk works all as specified in particular specification in ca. , supply and stacking of stone chips of size 11.20 mm for bc 30 mm thk works all as specified in particular specification in ca. , supply and stacking of stone chips of size 6.70 mm for bm 75mm & bc 30 mm thk works all as specified in particular specification in ca. , supply and stacking of sand for bm 75 mm & bc 30 mm thk works all as specified in particular specification in ca.

State Government

TRN :49055068 | 16 May, 2025

Tender Value : 21.14 Lacs

Dhanbad - Jharkhand

Tender for renovation of electromechanical equipment at rural pipe w/s scheme mairanwatandunder d.w.&s. mechanical division, dhanbadfor , cost towards lifting of 20 h.p. wpil ltdv.t. pump set with6” dia column pipe (total 50ft) from intake well and lowering the same after repairing with all labour tools and tackles , cost towards dismanteling of 20 h.p. wpil make v.t. pump, cleaning and checking, repairing and changing of following parts such as (for each pump) (a) pump shaft of s.s materials(25mm dia) as per sample 2 nos. (b) impeller intermediate bush of s.s materials as per sample 2 nos. (c) impeller key/collet -2nos. (d) line shaft sleeve of size 25mm x 150 mm long s.s materials 5 nos.(e) line shaft socket of size 50mmx120mm long of s.s materials 5 nos.(f) line shaft of s.s materials (size 1.5m x 25 mm dia)- 3nos(g) cost for making and fiting cast iron spider bearing with rubber cutless bush suitable of 6” dia coloumn pipe 4 nos. (h) top shaft of s.s materials of size 25 mm dia as per sample 1 nos. (i) check nut with locking arrangement 01 nos.(j) neckring bush of g.m -3 nos. (k) coloumn pipe high tension bolt with nut, washer as per sample 40 nos.(l) rubber insertion/packing paper as per requirementsand testing on load , cost towards overhauling of 20 h.p. sq cage induction motor operated on 415v 3 phase, 50c/s, 1450rpm, dismantling cleaning and heating, varnishing reassembly, testing etc all complete , cost towards rewinding of 20 h.p. sq cage vertical hallow shaft induction motor operated on 415v, 3 phase, 50hz, 1450 rpm with s/f of super enameled copper wire of suitable gauge, other insulating materials, heating varnishing assembly of the motor and testing on full load(wt of copper wire – 9kg , cost for repairing of motor control panel and changing of its damaged spare such as mnx-50 contactor-3 nos, c.t. coil – 3 nos, voltmeter-1 no, amp meter- 1 nos, 63 no mccb -63 amp. - 1 nos. etc all complete and testing on full load , cost for s/f of 40 watt led light (1 no each outside & inside of pump house) with bracket and required copper wire. , cost for transportation of materials for repairing from p/p to work shop to vice versa. , wtp phase-i supplying all labour tools and tackles for taking out old and damaged c/f pump set with all accessories demolition of foundation for installation of new hsc centrifugal pump sets , cost towards s.i.t.c of electrically driven horizontal spilt casing c/f pump set make (kirloskar/wpil/mathe& plate/jyoti) coupled with tefc sq. cage induction motor make(kirloskar/crompton/jyoti/abb) operated on 3 phase , 415 ± 10% volts 50 hz, 1470 rpm mounted on common fabricated base plate with suitable size of cidf sluice valve-1 no cidf nr valve- 1 no, foot valve- 1 no, pressure gauge- 1 no, tyre coupling – 1no etc all complete head-57mtr, discharge 36m3/hr , supplying all labour tools and tackles for making p.c.c foundation- 1 no of size4 x 3 x 3’ with all materials such as cement, sand, stone chips, foundation bolt- 6 nos. etc all complete and plastering and punning over exposed surface for each pump set , cost towards supplying & laying of 10 mm2x3 core pvc insulated and pvcsheathed 1.1 kv grade unarmored copper cable make polycab/kei/universal?isi marked reputed make (from mcp to motor) for both pump set. , cost towards making cable mouth for 10 mm2x3 core pvc insulated &pvc sheathed 1.1kvgrade unarmored copper cable - , cost for repairing of motor control panel and changing of its damaged spare such as contactor mnx-50 – 3 nos,c.t. coil 3 nos. volt meter – 1 no. ampere meter – 1 no. 63amp-1 no. mccb – 1 no etc all complete and testing on full load , cost for laying of delivery pipe line with supply & fitting of 5” dia heavy duty g.i. pipe 3mtrflenge 5 nos. bend 1 nos. nut, bolt rubber insertion, cutting and welding of pipe in required size with all labour tools & tackles , cost for s/f of 40 wt led light (1 no each outside & inside of pump house) with bracket and required copper wire. , cost for providing priming arrangement with supply & fitting of 500 ltr p.v.c tank -1 no , 1”diap.v.cpipe9 mtr, 1”valve-2 nos., elbow- 4 nos., tee- 1 no, socket-3nos etc all complete , wtp phase-ii supplying all labour tools and tackles for taking out old and damaged c/f pump set with all accessories demolition of foundation for installation of new hsc centrifugal pump sets , cost towards s.i.t.c of electrically driven horizontal spilt casing c/f pump set make (kirloskar/wpil/mather & plate/jyoti) coupled with tefc sq. cage induction motor make(kirloskar/crompton/jyoti/abb) operated on 415 ± 10% volts 50 hz, 1470 rpm mounted on common fabricated base plate with suitable size of cidf sluice valve-1 no, cidf nr valve- 1 no, foot valve- 1 no, pressure gauge- 1 no, tyre coupling – 1no etc all complete [head-57mtr, discharge 36m3/hr] , supplying all labour tools and tackles for making p.c.c foundation- 1 no of size 4’ x 3’ x 3’with all materials such as cement, sand, stone chips, foundation bolt- 6 nos. etc all complete and plastering and punning over exposed surface , cost for laying of delivery pipe line with supply & fitting of 5” dia heavy duty g.i. pipe 3 mtr flange 5 nos., tee-1no ,bend 1 nos. nut, bolt rubber insertion, cutting and welding of pipe in required size with all labour tools & tackles , cost towards overhauling of 20 h.p. sq cage induction motor operated on 415v, 3 phase, 50c/s, 1500rpm ,dismantling clearing and heating, varnishing reassembly, testing etc all complete , cost for s/f offloor/wall mounted cubical l.t. power control panel fabricated with ms sheet and painted, dust and vermin proof, proper ventilated consisting of proper distribution 100 amp copper bus-bar 4 pole- 1 set, 100amp mccbl&t/siemens make for incoming feeder- 1nos , 63amp mccb -2nos for outgoing , (1 no for each pump sets) suitable capacity of fasd starter l&t/ bch/schnidermake-2nosm, 0-500v voltmeter with seleetor switch – 2 nos., phase indicating neon lamp- 9 nos. s.p.p. --- doing internal wiring with proper gauge of copper wire etc all complete job and testing on load , cost towards supplying & laying of 10 mm2x3 core pvc insulated and pvcsheathed 1.1 kv grade unarmored copper cable make polycab/kei/universal isi marked reputed make (from mcp to motor) , cost towards making cable mouth for 10 mm2x3 core pvc insulated &pvc sheathed 1.1kv grade unarmored copper cable , cost towards supply & laying of 3.5 corex 70sq mmpvc insulated and pvc sheathed armored aluminum cable of 1100 v grade isi marked make havells/polycab/finelen/gemscab/any reputed make , cost for s/f of 40wt led light (1 no each outside & inside of pump house) with bracket and required copper wire. , cost for providing priming arrangement with supply & fitting of 500 ltr p.v.c tank -1 no , 1”diap.v.cpipe9 mtr, 1”valve-2 nos., elbow- 4 nos., tee- 1 nos , socket-4nosetc all complete , cost for transporting of taken out pump set and other materials from pump plant to store at dhanbad

State Government

TRN :49055100 | 16 May, 2025

Tender Value : 38.90 Lacs

Dhanbad - Jharkhand

Tender for renovation of electro mechanical system at rural pipe water supply scheme at ojhadih katania under d.w and s mechanical division dhanbad , supplying all labour tools and tackles for taking out old and damage 10 h.p. v,t, pump set from intake well with all accessories, demolltion of mounting chanel for installation of new v,t. pump sets , s.i.t.c of electrically driven vertical turbine pump sets kirloskar/wpil/ mather&plate/jyotimake having discharge capacity of raw water 55 m3/h against total head of 25 mtr coupled with vertical hollow shaft sq. cage induction motor make (kirloskar/abb)/jyoti) operated on 415 ± 10% volts, 50 hz, 1460 rpm with sole plate, discharge head m.s. d.f. coloumn assembly random length of 5ft, total 50 ft s.s. line shaft s.s. socket, spider bearing with rubber cut less bush, cidf sluice valve- 1 no, cidf nr valve- 1 no pressure guage – 1 no etc all complete note- motor capacity should have 20% above of the pump , supplying all labour tools and tackles for making pcc foundation 2’x2’x1’ with all materials such as sand, stone chips, cement, foundation bolt etc all complete including fixing of sole plate for installation of new v.t. pump sets , providing floor/wall mounted cubical l.t power control panel fabricated with ms sheet and painted dust & vermin proof, proper ventilated consisting of a. proper distribution 63 amp copper bus bar 4 pole- 1 set b. microprocessor based tpn mccb 63 amp l&t/siemens/abb make with earth fault relay for incoming feeder – 1 nos c. mccb 32 amp tp l&t/siemens/abb make for outgoing feeder-2 nos d. 32a dp mcb for lighting – 1 nos. e. 0-500 v voltmeter with selector switch – 1 set ct operated ampere meter 0-50 with ct – 3 set, phase indication neon lamp- 6 nos. f. s.p.p – 2 nos. doing internal wiring with proper gauge of copper wire etc all complete job and testing on load – 1 set , cost towards supplying and laying of 6 mm2 x 3 core pvc insulated and pvc sheathed, 1.1 kv grade unarmouredcopper cable of reputed make and isi marked doing connection from panel to both motor , cost towards supplying and laying of 70 sq. mm x 3.5 core pvc, insulated and pvcshethed, 1.1 kv grade armouredalluminium cable of reputedmake and isi marked for doing connection from pole to main switch to panel , cost towards making cable mouth for a. 6 mm2 – 24 nos. , b. 50 mm2 – 16 nos. , supply & fixing 3 ton capacity triple gear chain pulley block with 6 mtr lifting chain of reputed make & i.s.i. marked , cost for making new common header with supply and fitting of 6” dia heavy duty g.i. pipe 6 mtr, 6”dia bend-2 nos., 6”dia tee- 1 no, 6” dia flange-12 nos., rubber insertion – 10 kg nut bolt washer – 10 kg with cutting of pipe in required length and and doing welding as required length and doing welding as required all complete job with materials and labours charges. , making chemicalwith required materials and labour tool & tackles , supply & laying of 8 swg copper/g.i. wire for making earthing connection into from earthing station to panel to motor , cost for supply and fitting 100 amp tpn main switch/switch disconnector and doing all line connection , sitc of 40kva servo control automatic voltage stabilizer suitable for input voltage 220v to 450v and out-put voltage 415v ± 1% 3phase 50hz with copper wound transformer (oil cooled) as mentioned below. the stabilizer self function satfictorilyeven if in coming supply is unbalanced between phases within range of 10% . the stabilizer should be constructed in cubical box, with bidirectional wheels for easy handle, necessary monitors in user’s control on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise /low push button etc. suitable capacity termination strips and bus-bars for incoming and outgoing cable should be provided. all 3 phases shall be independently monitored and corrected . following protections and indication shall be incorporated as per isi 9815 a) over voltage/under voltage b) single phasing c) cut off contactor with electronig output sensing unit d) suitable change over switch and earthing , cost for adding transformer oil of reputed make isi certified upto level , cost for supplying and fitting of 40watt led light with its bracket and doing wiring connection etc all complete , supplying all labour tools and tackles for taking out old and damaged c/f pump set with all accessories, demolition of foundation for installation of new hsc c/f pump set , sitc of electrical driven horizental split casing c/f pump set [make: kirloskar/wpil/jyoti/ mather & plate] having discharge capacity of clear water 55 m3/h against a total head of 72mtr coupled with tefc squirrel cage induction motor[make: kirloskar/abb/jyoti] operated on 415v, 3 phase, 50hz, 1460rpm mounted on common ms fabricated base plate with suitable size of cidf sluice valve-1no, cidf nr valve-1no, foot valve-1no, pressure gauge-1no, tyre coupling-1set etc all complete , supplying all labour tools and tackles and making pcc foundation of 4’ x 3’ x 3’ with all materials such as cement, send, stone chips, foundation bolt-6nos etc all complete and plastering and punning over exposed surface. , providing floor/wall mounted cubical l.t power control panel fabricated with ms sheet and painted dust & vermin proof, proper ventilated consisting of g. proper distribution 100 amp copper bus bar 4 pole- 1 set h. microprocessor based tpn mccb/ 100 amp l&t/siemens/abb make with earth fault relay for incoming feeder – 1 nos i. mccb 63 amp tp l&t/siemens/abb make for outgoing feeder-2 nos j. 32a dp mcb for lighting – 2 nos. k. 0-500 v voltmeter with selector switch – 1 set ct operated ampere meter 0-100 with ct – set phase indication neon lamp- 6 nos. l. s.p.p – 2 nos. doing internal wiring with proper gauge of copper wire etc all complete job and testing on load – 1 set , cost towards supplying and laying of 6 mm2 x 3 core pvc insulated and pvc sheathed, 1.1 kv grade unarmouredcopper cable of reputed make and isi marked doing connection from panel to both motor , cost towards supplying and laying of 50 mm sq. x 3.5 core pvc insulated and pvc sheathed, 1.1 kv grade armoured aluminium cable of reputedmake and isi marked for doing connection from pole to main switch to panel , cost towards making cable mouth for a. 6 mm2 – 24 nos. , b. 50 mm2 – 16 nos. , cost for making new common header with supply and fitting of 6” dia heavy duty g.i. pipe 6 mtr 6”dia bend-2 nos. 6”dia tee- 1 no 6” dia flange-12 nos. rubber insertion – 10 kg nut bolt washer – 10 kg with cutting of pipe in required length and doing welding as required length and doing welding as required length and doing welding as required all complete job with materials and labours charges , making chemical earthing with required materials and labour tool & tackles , suuply& laying of 8 swg copper/g.i. wire for making earthing connection into from earthing station to panel to motor , cost for supply and fitting 100 amp tpn main switch/switch disconnector and doing all line connection , providing& erecting of 60kva servo control automatic voltage stabilizer suitable for input voltage 220v to 450v and out-put voltage 415v ± 1% 3phase 50hz with copper wound transformer (oil cooled) as mentioned below. the stabilizer self function satfictorilyeven if incomming supply is unbalanced between phases within range of 10% . the stabilizer should be constructed in cubical box, with bidirectional wheels for easy handle necessary monitors in user’s control on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise /low push button etc. suitable capacity termination strips and bus-bars for incoming and outgoing cable should be provided. all 3 phases shall be independently monitored and corrected . following protections and indication shall be incorporated as per isi 9815 a) over voltage/under voltage b) single phasing c) cut off contactor with electronig output sensing unit d) suitable change over switch and earthing , cost for adding transformer oil of reputed make isi certified upto level , cost for transporting of taken out pump set and other materials from pump plant to store dhanbad

Government Departments

TRN :49055388 | 21 May, 2025

Tender Value : 8.06 Lacs

Agra - Uttar Pradesh

Tender for tender for zone-1, ward no.-92, rawatpara roshan mohalla, work of preparing the floor along with repair of office building. - demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. 2 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge.15.7.4 in cement mortar 3 cleaning of the site for warkable etc. all complete. (non scheduled) 4 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:4 (1 cement : 4 coarse sand) (dsr 2023 sh-6.4.1 ) 5 brick work 7 cm thick with common burnt clay f.p.s. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. (dsr 2023 sh-6.8 ) 6 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,taircases and spiral stair cases above plinth level up to floor fiveevel, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).(dsr 2023 sh-5.3 ) 7 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more(dsr 2023 sh-5.22.6) 8 centering and shuttering including strutting, propping etc. and removal of form work for :columns, piers, abutments, pillars, posts and struts(dsr 2023 sh-4.3.3 ) 9 12 mm cement plaster of mix : 1:4(1 cement: 4 fine sand)(dsr 2023 sh-13.1.1 ) 10 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(dsr 2023 sh-10.1 ) 11 providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.fire retardant plywood conforming to is: 5509(dsr 2023 sh-9.126.2 ) 12 providing and fixing isi marked is:1341 m.s. pressed butt hinges bright finished with necessary screws etc. complete :)75x47x1.70 mm (dsr 2023 sh-9.55.3 ) 13 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side ofdhesive bonding quality conforming to is : 2046 type s including cost of adhesive of approved quality. 1.0 mm thick (dsr 2023 sh-9.127.2 ) 14 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre (dsr 2023 sh-13.41.1 ) 15 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture(dsr 2023 sh-1021sub head : 13 finishing13.48.3 ) 16 providing & fixing white vitreous china water closet squatting pan (indian type) along with “s” or “p” trap including dismantling of old wc seat and “s” or “p” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. long pattern w.c pan of size 580x440 mm (dsr 2023 sh-14.80.1) 17 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require white vitreous china flat back wash basin size 450x 300 mm with single 15mm c.p. brass(dsr 2023 sh-17.7.7) 18 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is: 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required(dsr 2023 sh-17.5.1 ) 19 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c. automatic flushing cistern, with fittings, standard size g.i./ pvc flush pipe for back and front flush with standard spreader pipes with fittings, g.i clamps and c.p. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: single squatting plate with 5 litre p.v.c. automatic flushing cistern(dsr 2023 sh-17.6.1 ) 20 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(dsr 2023 sh-11.55.1 ) 21 providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to isi : 12701, colour of opaque white or as approved by engineer-in- charge. the rate includes making necessary holes for inlet, outlet & over flow pipes. the base support i/c fittings & fixtures for tank shall be paid separately 22 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge100 mm nominal size dia 23 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge150 mm nominal size dia 24 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one stepcpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work - exposed on wall 15 mm nominal dia pipes 25 providing and fixing ptmt bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms 26 providing and fixing ptmt stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms) 27 mirror of superior make glass 60x45 cm 28 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 29 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 30 supply and fixing of light fitting switch board. (none sheduled) 31 supply and fixing wiring of light point. (none sheduled) 32 s/l/j of 20mm dia pvc cunduct pipe etc. all complete. 33 supply & fixing of wiring sub main. 34 supply & fixing of plug point 15mm. 35 lettering & painting of wall etc. all complete. 36 supply & fixing of 27watt. cfl etc. all complete. 37 carriage of materials by manual labour including loading, unloading and stacking for lead less than 01-50 mtrm.207.34+30.42 every 50 additonal meter 38 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 39 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 40 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.) 41 chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : light shade pigment using white cement 42 marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :raj nagar plain 43 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)(dsr 2023 sh-10.28 ) 44 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (dsr 2023 s h) 45 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 46 making ornamental painting with special design make by specialist painter laying of two coat birla white putty and design by asian paint including all material etc. all complete. (nn approved) 47 sub total 48 add/deduction rs. for estimate figure amount match 49 grand total

State Government

TRN :49055818 | 21 May, 2025

Tender Value : 7.81 Lacs

24 Paraganas South - West Bengal

Tender for settler with abr at ramchandrapur near rabin mudi shop- 1 earth work excavation of foundation trenchs or drain in all sorts of soil including mix soil excluding laterite or sand stone includinga) depth of excavation not exceeding 1,500 mm 2 (b) depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring. 3 (a) filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) 4 single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. 5 ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant is codes. (i) pakur variety 6 ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant is codes.(i) pakur variety 7 ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant is codes.(i) pakur variety 8 reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) for works in foundation and upto roof of ground floor/upto 4 m (i) tor steel/mild steel i. sail/tata/rinl 9 hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) 10 brick work with 1st class bricks in cement mortert(1:4) a)in foundation and plinthb) in super structure, in all floor. 11 plastering at wall with sand and cement morterincluding rounding off or chamfaring corner (1:6) 20 mm th. 12 net cement punning about 1.5 mm thick in wall dado window floor drain etc. 13 supply of upvc pipes (b type) & fittings conforming to is-13592-1992.(a) (i) single socketed 3 meter length (b) 110 mm inlet/outlet of hpgf 14 labour for fitting and fixing u.p.v.c. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or r.c. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the engineer in-charge. (payment will be made on centre line measurement of the total pipeline including specials.(a) above ground (ii) 110 mm dia. 15 supply of upvc pipes (b type) & fittings conforming to is-13592-1992.(b) fittings (ii) plain tee (b) 110 mm 16 supplying, fitting and fixing in position c.i. manhole/ pit cover with rim. (b) square- 600 mm x 600 mm x 50 kg (approx.) 17 supply of upvc pipes (b type) & fittings conforming to is-13592-1992. providing & supplying cowl 18 c.i. sluice valve with flanged ends drilled to as per i.s. 1358/62 and having all cast iron components as per i.s. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 mt per sq. cm. spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to i.s. 780/71, painted black all over with asphalt base paint tested to 21 kg (hydraulic pressure) per sq. cm., valve opening to anticlockwise direction, fitted and fixed complete. 19 providing and laying of filter media with granularmaterials/stone crushed aggregates/brickaggregates /river bed materials satisfying therequirements laid down in clause 2504.2.2 of mort&h 20 earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (payment to be made on the basis of measurement of finished quantity of work)(a) with earth obtained from excavation of foundation 21 surfacedressingof the ground inany kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. 22 18% cgst & sgst 23 1 % labour cess

State Government

TRN :49055823 | 21 May, 2025

Tender Value : 4.49 Lacs

24 Paraganas South - West Bengal

Tender for settler with abr at uttar ramchandrapur near gul company- 1 earth work excavation of foundation trenchs or drain in all sorts of soil including mix soil excluding laterite or sand stone includinga) depth of excavation not exceeding 1,500 mm 2 (b) depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring. 3 (a) filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) 4 single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. 5 ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant is codes. (i) pakur variety 6 ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant is codes.(i) pakur variety 7 ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant is codes.(i) pakur variety 8 reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) for works in foundation and upto roof of ground floor/upto 4 m (i) tor steel/mild steel i. sail/tata/rinl 9 hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) 10 brick work with 1st class bricks in cement mortert(1:4) a)in foundation and plinthb) in super structure, in all floor. 11 plastering at wall with sand and cement morterincluding rounding off or chamfaring corner (1:6) 20 mm th. 12 net cement punning about 1.5 mm thick in wall dado window floor drain etc. 13 supply of upvc pipes (b type) & fittings conforming to is-13592-1992.(a) (i) single socketed 3 meter length (b) 110 mm inlet/outlet of hpgf 14 labour for fitting and fixing u.p.v.c. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or r.c. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the engineer in-charge. (payment will be made on centre line measurement of the total pipeline including specials.(a) above ground (ii) 110 mm dia. 15 supply of upvc pipes (b type) & fittings conforming to is-13592-1992.(b) fittings (ii) plain tee (b) 110 mm 16 supplying, fitting and fixing in position c.i. manhole/ pit cover with rim. (b) square- 600 mm x 600 mm x 50 kg (approx.) 17 supply of upvc pipes (b type) & fittings conforming to is-13592-1992. providing & supplying cowl 18 c.i. sluice valve with flanged ends drilled to as per i.s. 1358/62 and having all cast iron components as per i.s. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 mt per sq. cm. spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to i.s. 780/71, painted black all over with asphalt base paint tested to 21 kg (hydraulic pressure) per sq. cm., valve opening to anticlockwise direction, fitted and fixed complete. 19 providing and laying of filter media with granularmaterials/stone crushed aggregates/brickaggregates /river bed materials satisfying therequirements laid down in clause 2504.2.2 of mort&h 20 earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (payment to be made on the basis of measurement of finished quantity of work)(a) with earth obtained from excavation of foundation 21 surfacedressingof the ground inany kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. 22 18% cgst & sgst 23 1 % labour cess

State Government

TRN :49056564 | 21 May, 2025

Tender Value : 7.81 Lacs

24 Paraganas South - West Bengal

Tender for settler with abr at dakshin ramchandrapur near tarun sangha shiv mandir- 1 earth work excavation of foundation trenchs or drain in all sorts of soil including mix soil excluding laterite or sand stone includinga) depth of excavation not exceeding 1,500 mm 2 (b) depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring. 3 (a) filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) 4 single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. 5 ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant is codes. (i) pakur variety 6 ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant is codes.(i) pakur variety 7 ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant is codes.(i) pakur variety 8 reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) for works in foundation and upto roof of ground floor/upto 4 m (i) tor steel/mild steel i. sail/tata/rinl 9 hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) 10 brick work with 1st class bricks in cement mortert(1:4) a)in foundation and plinthb) in super structure, in all floor. 11 plastering at wall with sand and cement morterincluding rounding off or chamfaring corner (1:6) 20 mm th. 12 net cement punning about 1.5 mm thick in wall dado window floor drain etc. 13 supply of upvc pipes (b type) & fittings conforming to is-13592-1992.(a) (i) single socketed 3 meter length (b) 110 mm inlet/outlet of hpgf 14 labour for fitting and fixing u.p.v.c. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or r.c. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the engineer in-charge. (payment will be made on centre line measurement of the total pipeline including specials.(a) above ground (ii) 110 mm dia. 15 supply of upvc pipes (b type) & fittings conforming to is-13592-1992.(b) fittings (ii) plain tee (b) 110 mm 16 supplying, fitting and fixing in position c.i. manhole/ pit cover with rim. (b) square- 600 mm x 600 mm x 50 kg (approx.) 17 supply of upvc pipes (b type) & fittings conforming to is-13592-1992. providing & supplying cowl 18 c.i. sluice valve with flanged ends drilled to as per i.s. 1358/62 and having all cast iron components as per i.s. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 mt per sq. cm. spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to i.s. 780/71, painted black all over with asphalt base paint tested to 21 kg (hydraulic pressure) per sq. cm., valve opening to anticlockwise direction, fitted and fixed complete. 19 providing and laying of filter media with granularmaterials/stone crushed aggregates/brickaggregates /river bed materials satisfying therequirements laid down in clause 2504.2.2 of mort&h 20 earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (payment to be made on the basis of measurement of finished quantity of work)(a) with earth obtained from excavation of foundation 21 surfacedressingof the ground inany kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. 22 18% cgst & sgst 23 1 % labour cess

State Government

TRN :49056708 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for santoshpur water supply scheme, t.w. no. iv, block: tarakeswar, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49056717 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for sibaichandi water supply scheme, t.w. no. v & vi, block: dhaniakhali, district - hooghly under electrical division, phe dte.-1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions]

State Government

TRN :49056725 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for amodghata water supply scheme, t.w. no. vi, block: chinsura mogra, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

Related Searched Keywords : stone chips

List of stone-chips Tenders

Get stone chips Tender Alert...

Related Searched Keywords : stone chips

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us