Filters

List of sun-screen-glass Tenders

List of latest sun-screen-glass Tenders in Indian Tenders. Click on any sun-screen-glass Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for sun-screen-glass Tenders.

All-Tenders (680)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Central Government/Public Sector

TRN :49054152 | 20 May, 2025

Tender Value : 77.92 Lacs

Abohar - Punjab

Tender for tender for special repair to building no p-137 at mil stn abohar; 1 demolition of cement concrete (un-reinforced) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise complete all as specified and directed by engr-in-charge. 2 material & labour for 75mm thick pcc 1:3:6, type c1, using 20mm graded stone aggregate as in hard standing ,plinth protection/path etc,laid in suitable panels n.exc 3.00 m length finished even and smooth without using extra cement with contraction(dummy)joints 65mm deepx10mm wide joints filledwithbituminous sealing compound of grade ‘a’/bitumen mastic filler/sealant complete all as specified and directed by engr-in-charge. 3 dismantling brick tiles in floor or in roofs laid dry and pointed in any cement mortar complete all as specified and directed. 4 demolition of mud in roofs any thickness incl plastering and leeping 5 m & l for 40mm thick cement concrete type b0 1:2:4, (using 12.5mm graded stone aggregate) as in, surface finished even and smooth without using extra cement 6 m & l 10mm thick rendering in cement mortar 1:3 on fair facesof brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by engr-in-charge. 7 m&l for preparation of roof top surfaces,providing and applying uv stable single component smart care damp proof ultra is a fiber reinforced elastomeric liquied appplied water proofing membrane formulated with pu hybrid polymers and reinforcing acrylics fibres and having sri of 106 on top of concrete roof surface in three coats including self primer at ratio pf dampproof and water 3:1 and coverage @ 1 ltr/10 sqm with a thickness of 650 micron. note : (i) 6 hrs interval between two coats will be maintained. (ii)the treatment shall be carried out by authorised applicator approved by ge as per the manufacturer(iii)payment will be made after providing warrnty certificate from the company. 8 m&l 40mm thick brick tiles laid/beded including screed bed 15mm thick in cement mortar (1:6) on existing lime concrete sufaces of roof,joints grouted flush in cement mortar (1:3) mixed with liquid wpc @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of mes sch part-i (2009) complete all as specified and directed by engr-in-charge. 9 m&l 40mm thick brick tiles( old serviceable tiles obtained from demolition/desmantled item shall be reused) laid/beded including screed bed 15mm thick in cement mortar (1:6) on existing lime concrete sufaces of roof,joints grouted flush in cement mortar (1:3) mixed with liquid wpc @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of mes sch part-i (2009) complete all as specified and directed by engr-in-charge. 10 dismantlingof reinforced cement concrete by chiseling (without affecting other portion) of any description and in any position as in roofs, floors (other than ground floor), beams, landing, chajjas and similar suspended work. 11 m&l reinforced cement concrete 1:1 1/2:3 (nominal mix) using 20mm graded stone aggregate as in slab supported on walls,beams and columns in floors,roofs,landings,balconiies,deck slabs and in shelves and the like all as specified and directed. (form work & reinforcement measured separately). 12 m & l mild steel tmt bars 10mm dia or over cut to length bent to shape required including cranking, hooking ends and binding with ms wire (annealed) not less than 0.90mm dia all as in column, beam etc . 13 m&l for form work to soffits of suspended slabs such as roof slabs,floor slabs,landings and similar work not exc.200 mm thick(horizontal or sloping) rough finish surface of concrete flat all as specified and directed. 14 m&l for precast reinforced cement concrete (1:2:4) type b1 (using 20 mm graded crushed stone aggregate) as in cover slab of drain/manhole set in cm (1:6).note :- cost of form work is deemed to be inclusive of unit rate quoted by the contractor & reinforcementshall be measured & paid separately.) 15 taking down chowkatsor frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm each & removing to store all as specified. 16 taking down chowkatswith shutters(without taking off shutters from the frame exceeding 1.50 sqm each but not exceeding 4 sqm) 17 taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by engineer-in- charge. 18 taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm eachcomplete all as specified and as directed by engineer-in- charge. 19 s&f factory made single extruded wpc (wood polymer composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin pvc polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 n (face) & 1100 n (edge), minimum compressive strength of 58 n/mm2, modules ofelasticity 900 n/mm2and resistance to spread of flame of class a category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with ms hold fast/ lugs/ss dash fasteners of required dia and length complete as per direction of engineer-in-charge. (m.s. hold fast/ lugs or ss dash fasteners shall be paid for separately). note :- for wpc solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed . 20 providing and fixing factory made single extruded wpc (wood polymer composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 n (face) & 900 n (edge), minimum compressive strength 50 n/mm2, modulus of elasticity 850 n/mm2 and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant. wpc to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer- in- charge including supply and fixing following items : (a) stainless steel (304 grade) finished butt hinges 100mm - 4 nos. per leaf (b) stainless steel (304 grade) finished square tower bolt 150 mm long - 2nos per leaf (c) stainless steel (304 grade) finished handles 150 mm - 2 nos. per leaf 21 supply and fixingfactory made pressed steel frames of size 125 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , includingbutt hinges suitable nos as directed for each leaf, complete all as specified and as directed by engineer-in- charge. 22 supply and fixingfactory made pressed steel frames of size 105 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including butt hinges suitable nos as directed for each leaf, complete all as specified and as directed by engineer-in- charge. 23 m&l cement concrete 1:3:6 type c-1 using 20mm graded stone aggregate for filling of pressed steel frame and hold fast blocks etc complete all as specified and directed by engineer - in - charge. 24 s & f factory made plain framed, panelled shutter iind class hardwood rail and style 35 mm thickness (two panel) with lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 (part i), kiln seasoned and chemically pressure treated complete all as specified and directed by engineer - in - charge. 25 s & f factory made 35mm thick iind class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in ssr part – i, section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed by engineer - in - charge. 26 s & f100 mm aluminium alloy anodised butt hinges, and fixed with steel scerws for frp doors/pvc door, type b-21complete all as specified and directed by engineer - in - charge. 27 s & f in repair 100 mm mild steel butt hinges, and fixed with steel scerws for wooden doors, complete all as specified and directed by engineer - in - charge.note :- rate deemed including necessary welding etc) 28 s & f tower bolt 200 mm of aluminum complete all as specified and directed by engineer - in - charge. 29 s & f in repair tower bolt 200 mm of aluminum complete all as specified and directed by engineer - in - charge. 30 s & f door handle d type 150 mm of aluminum complete all as specified and directed by engineer - in - charge. 31 s & f in repair door handle d type 150 mm of aluminum complete all as specified and directed by engineer - in - charge. 32 s & f aluminium alloy, anodised, sliding door bolt 300mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed. 33 s & f in replacement aluminium alloy, anodised, sliding door bolt 300mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed. 34 s&f floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor. 35 s&f in repairs floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor. 36 s & f mild steel 300mm ordinary rat rail rod pattern spring inluding roller and roller plate complete all as specified. 37 s & f in repairs mild steel 300mm ordinary rat rail rod pattern spring inluding roller and roller plate complete all as specified. 38 s& fstainless steel curtain rod 25 mm dia , including fancy type brackets and pair of decorated end knobs (finials), stop roller etc.as per site requirement, fixed to wall with fixing accessories,including taking down old existing curtain rods any description complete all as specified and directed by engr-in-charge. 39 s&f factory made box type steel window with side hung shuters both glazed and gauged, shutter frame 60x25mm erw hollow p section with wall thickness not less than 1mm fixed to pressed steel frame 120mmx70mmx1.60mm thick including fixing glazed portion, iron grills 8mm suare ms barhinges with steel handle and fitting, lugs etc., including one shop coat of primer complete all as specified.(drg no btd889 sheet 1/4 ).note :- (i) wire mesh and glass shall be measured and paid separately under relevent items of sch/boq.(ii)measurement for payment shall be the opening area of the window between inner edges of wall. 40 s&f factory made box type steel window with side hung glazedshutter, frame 60x25mm erw hollow p section with wall thickness not less than 1mm fixed to pressed steel frame 120mmx70mmx1.60mm thick including fixing glazed portion, iron grills 8mm suare ms barhinges with steel handle and fitting, lugs etc., including one shop coat of primer complete all as specified.note :- (i)wire mesh and glass shall be measured and paid separately under relevent items of sch/boq.(ii)measurement for payment shall be the opening area of the window between inner edges of wall. 41 s&f stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm all as specified. 42 s & f in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm all as specified. 43 s & f 4 mm thick sheet glass ordinary quality and glazing within square not exceeding 0.50 sqm including aluminium cleat/rubber beading in each pane complete all as specified and directed by engineer - in - charge. 44 supply & fixing aluminium anodisedframes/chowkhats,shutter and like made out of aluminium sectionpowder coated(minimum thickness of powder coating not less than 50 micron) for window, ventilators and aluminium partition with one or more rebates or without rebate including joining cleat for fixing etc., the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners. aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and as directed by engineer-in-charge.. 45 s & f figured glass 4 mm thick pin head type and glazing withnot exceeding 0.50 sqmincluding aluminium cleat/rubber beading in each pan complete all as specified and directed by engineer - in - charge. 46 material and labour for machine cut 16 to 18 mm thick, kota stone slab (size of slab not less than 500x550mm for flooring and in single piece for treads of staircase), laid over and including 20 mm thick bedding layer in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish) andpolishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by engineer-in-charge. 47 material and labour for machine cut 16-18mm thick, kota stone slab as in skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish ) and polishing by machine, including machine cutting to make it square or rectangularcomplete all as specified and as directed by engineer-in-charge. 48 taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc. 49 m & lfor rendering 15mm thik on fair faces of brick work in cement mortar 1:6 finished even & smooth without using extra cement. 50 m & lfor rendering 15mm thick on fair faces of brick work in cement mortar 1:4 finished even & smooth without using extra cement. 51 m&l rendering10 mm thick in cement mortar 1:3 on fair faces of concrete surfaces of ceiling finishing even and smooth without using extra cement. 52 m&l integal water proofing compound 53 preparation of new plastered surfaces/existing platered surfaces and applyingwall care putty in internal/external walls/rcc surfaces/soffits of chajjas/roof projections/cantilevers/balcony/ceilings etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior/exterior painting complete all as specified and directed.note : (i) the prepared surface after wall putty, the contractor will inform to the ge as well as to the engineer-in-charge for site inspection before applying further external finishes. please note that the further external finishes work will start only after approval of the prepared surface from the ge as well as to the engineer-in-charge through site order. 54 preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) @ 12 sq.m/litre/2 coats by using spray gun to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. 55 preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats by by using spray gun to ceiling surfaces over & including a coat of interior primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. 56 preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade)@ 5 sq.m/litre/2 coats by using spray gun to external walls/rcc surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed. 57 preparation of new/existing plastered surfaces as in ceilings and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. about 1.3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer-in-charge. 58 preparation of new/existing plastered surfaces as in walls and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. about 1.3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer-in-charge. 59 m & l providing two coats of synthetic enamel paint over new steel surfaces and a coat of red oxide primer onincluding preparation of surface of any description not exceeding 10 cm width or girth complete all as specified and directed by engineer -in -charge. 60 m & l providing two coats of synthetic enamel paint over new wooden surface including preparation of surface withprimer all as specified. 61 m&l for preperationof old steel surface and applying two coat of synthetic enamel paint complete all as specified and directed by engineer -in -charge. 62 m&l for preperationof old wooden surface and applying two coat of synthetic enamel paintcomplete all as specified and directed by engineer -in -charge. 63 m&l for shotcreting 25mm thick in rcc columns, beams and slabs etc in layers with approved design mix (minimum cement content of 350 kg/cum on m-25) concrete having the specified minimum characterristic compressive strength (with ordinary protland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria) including the cost of centering and shuttering at edges and corners etc as directed by engineer-in-charge including chipping of unsound /weak concrete material 25 mmaverage thickness from slabs,beams, columns etc with manual chisel and /or by standred power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc. including removal of rust by applying approved rust removal chemical & the coating with dr fixit epoxy zinc primer or equivalent @ 6sqm/ltr at dft of 100microns as per specifications and disposal of debries for all lead and lifts all complete as per direction of engineer-in-charge. 64 m&l hard drawn steel wire fabric not exc 4kg/sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemntall as specified & directed by engineer-in-charge. 65 m & l 5mm thick rendering in cement mortar 1:3 on fair facesof brick work or concrete surfaces of ceiling finished even and smooth without using extra cementcomplete all as specified and directed by engineer - in - charge . 66 dismantling structural steel work including doors,gates but excluding framed truss etc. 67 s & f framed work such as grills,cooler stand ,ladder grating and sun shed etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming tofe 410-0 or fe 310-0 all as specified . 68 dismantling of floor hearth or wall tiling including cement mortar bedding ( but not backing) and rubbish off the permices. 69 s&f glazed ceramic colouredtiles joint free 350x250x7mm/450x350x7mm square or rectanguleras on walls etc set and jointed in neat cement slurry and pointed in whiteor coloured cement to match over and including 10mm thick rendering in cm 1:4 complete all as specified and directed by engr-in-charge. 70 m&l non skid ceramic coloured /printed tiles 7 to 8 mm thick( square / rectangular) area of each tile exc. 0.11 sqm but n. exc, 0.18 sqm in floor and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shadeover and incl 15 mm thick screed bed in cm 1:6 complete all as specified and directed by engr-in-charge. 71 m&l cement concrete type b-0, 1:2:4 using 12.5 mm graded stone aggregate as in floors 25 mm thick for tilesall as specified.& directed by engr -in-charge.. 72 m&l 16-18 mm thick granite (of any type ) work (table rubbed and polished ) in cooking platform and likein cm (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding/moulding of edges. 73 demolitionof cement concrete ( un re-inforced) of any description in ground floor and pavings exc15 cm thickness (below or above gl). 74 material and labour for water proofing treatment to rcc sunken slab and adjoining vertical slab as described following any one method complete as per directions of ge. 75 method 1(a) supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, smart care damp proof 2k, having 100% elongation as per astm d412, resisting 5 bars hydrostatic pressure as per din 1048, reduction to rapid chloride shall be 70 as per din 1048, crack bridging upto 1.2mm as per astm 4548.5 clean all working surface & made free from dirt, grease laitance etc. after inspection for all working area rough surface, cracks & from dirt, grease laitance etc. after inspection for all working area rough surface, cracks & construction joint are treated by polymer modified mortar of 1:1:4 (1 cement : 1polymer : 4 sand). making gola of size 75x75mm at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 (1 cement : 1 polymer : 4 sand). the coating shall be terminated at 1600mm in toilet/2100mm in bathroom on vertical walls. the mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing and shall have consumption of 1.5kg/sqm per coats, etc, complete as per manufactures specifications.(b) bore packing: all the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout – smart care gp grout having dual shrinkage compensation property. before the bore packing, surface of the pvc pie and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent. (c) apply12-15mm plaster on slab and vertical surface admixed with smart care vitalia neo @200ml per bag of cement before treatment. 76 method 2(a) supplying and applying two component cementitious & acrylic flexible water proofing & protective coating, two coats with 1mm dft, having hydrostatic (positive) water pressure resistance (din 1048) is 7. abrasion resistance, cm/km is 0.09 of dr fixit pidifin 2k @ 1.5kg/sqm with a paint brush over existing slab surface and adjoining vertical surface. the polyester reinforced coated netof 45g/sqm, 2.5mmx2.5mm is laying on the surface immediately on the first coat of two component modified polymer dr fixit pidifin 2k. after removal of all lose materials like dust etc. with wire brush coir brushes from surface to get absolutely cleaned surface free of foreign contaminant filling of crack and patches with polymer based mortar/micro concrete, after that making the gola onsurrounding wall’s junction and seal the vertical walls. in case of core cutting on the surface, the joint is seal with non-shrink grout.(b) the coating shall be terminated at 1600mm in toilet/2100mm in bathroom on vertical walls.(c) apply12-15mm water proof plaster on slab and vertical surface admixed with dr fixit pidiproof 77 m & l pcc (1:5:10)using 40mm graded burnt bricksaggregate as in foundation filling & mass concrete or as in sunkenfloor complete all as specified & directed by engineer-in-charge 78 dismantling water tanks and removing to store ofexc 500 and nexc 1000 ltr capacity 79 s & f rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in ssr part i of capacity 1000 litres all as specified and directed by engineer - in - charge . 80 s&f in repair 20mm ball brass valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed. 81 s & f in 20mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed all as specified . 82 s & f in 25 mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed all as specified . 83 s & f in repairs pvc 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of pvc 32mm bore and connection to wc pan complete all as specified. 84 s&f in repair viterous china squating pan orrisa pattern size 580/440mm wash down water closet pan ,white (excluding fixing bolts, flushing cistern and flush pipe) with plastic seat cover. 85 s&f in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including connection to drain (or outgoing pipe) and to flushing pipe ,anti-syphonage pipe and white closed patern with flat bottom & mild steel cromium plated or aluminium hinging device plasticseat cover complete . 86 s&f repairs vitreous china half stall urinals flat back white minimum with grating and union for discharge pipe ,providing & fixing plugs, bedding urinal against wall in cm 1:2 , securing urinal to plugs with & incl 60mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cistern with nbrackets, flush pipe, grating and union for discharge pipe complete all as specified. 87 s & f in repairs vitrous china oval wash hand basin white of size 550x400 mm including brackets 300mm long pvc connection with brass nuts, 40mm dia waste coupling including cutting for and pinning in end of brackets or erecting stand etccoloured top bowl type screwed shank fly nut flange end including cutting for and pinning in granite slab of hole including 32 mm dia chromium plated waste coupling and bottle trap all as specified. 88 s&f in repair 600mm x 450mm beveled edge mirror of selected quality glass on 6mm thick commercial plywood and fixed wooden plugs with chromium plated brass screw and cup washes fixed in repair. 89 s & f repairs 15 mm bore concealed stop cock cast copper alloy screwed down high pressurewith crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed but fancy type chromium plated with long shank and cup (concealled type) 90 s & f in repairs 15mm bore angle cock one waychromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified . 91 s & f in repairs 15 mm bore bib tap fancy type chromium plated with crutch or butterfly handle screwed down ,screwed for iron pipe all as specified. 92 s&f in repairs pillar taps 15mm borefancy type chromium plated cast copper alloywith capstan heads scre-wed down high pressure with or without lettered hot orcold with long screwed shanks and fly nuts screwed for iron pipe . isi marked 93 s&f in repair brass chromium plated central hole basin mixer with regular spout,popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed by engr-in-charge. 94 s&fin repair brass chromium plated shower rose 125mm size with swivel joints,any size, incl shower arm fixing to pipe or union complete all as specified and directed by engr-in-charge. 95 s&f in repair pvc connection both side brass unions internal for size 15mm dia and 450mm long all as specified and directed by engineer-in-charge. 96 s&f ewc jet spray complete all as specified and directed. 97 s & f in repairsoap dish approximately size 160 x160x 90 mm and fixed withas chromium plated brass screws complete all as specified and directed by engineer -in -charge. 98 s&f peg set of stainless steel solid body of 125mm to 175 mm having 6 nos hooks fixed with brass chromium plated screws complete in all as specified 99 taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed by engr-in-charge. 100 fixing only mild steel tubes of size 15mm bore (medium grade) galvanised with all fittingsand fixed complete to wallall as specified & directed by engineer-in-charge. 101 supply & fixing mild steel tubes of size 15mm bore (medium grade) galvanised with all fittings and fixed complete to wallall as specified & directed by engineer-in-charge. 102 taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store omplete all as specified and directed by engineer -in -charge. 103 supply & fixing of 16mm outer dia cpvc pipes sdr 11 including all fittings plain/brass threaded cpvc sdr 11 fittings (like elbow, tee, socket, reducer, union, bushing, step over bends, end cap, end plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including cpvc solvent cement for jointing omplete all as specified and directed by engineer -in -charge. 104 supply & fixing of 20mm outer dia cpvc pipes sdr 11 including all fittings plain/brass threaded cpvc sdr 11 fittings (like elbow, tee, socket, reducer, union, bushing, step over bends, end cap, end plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including cpvc solvent cement for jointing omplete all as specified and directed by engineer -in -charge. note :-(i) pipes inside the buildings shall be fixed concealed and outside the buildings shall be fixed on the surface along wall with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, as directed by engineer-in-charge.(ii)bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on btd drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. 105 supply & fixing of 25mm outer dia cpvc pipes sdr 11 including all fittings plain/brass threaded cpvc sdr 11 fittings (like elbow, tee, socket, reducer, union, bushing, step over bends, end cap, end plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including cpvc solvent cement for jointing complete all as specified and as directed.note :- (i) pipes inside the buildings shall be fixed concealed and outside thebuildings shall be fixed on the surface along wall with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, as directed by engineer-in-charge.(ii) bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on btd drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. 106 taking up or down steel tubing of 25 to 32 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed by engr-in-charge. 107 s & f 40mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed by engineer - in - charge. 108 dismantling of cast iron pipes jointed in cement mortar and taking out from trenches walls etc upto 100 mm bore all as specified and directed by engr-in-charge . 109 supply & fixing 110mm bore upvc pipes grade b single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant c complete all as specified and directed by engr-in-charge. 110 supply & fixing 75mm bore upvc pipes grade b single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and directed by engr-in-charge. 111 supply & fixing upvc junction (double t/socket) grade b equal or unequal suitable for 110mm bore pipe complete all as specified and complete all as specified and directed by engr-in-charge. 112 all as per item no 109 above 113 supply & fixing upvc bends (any radius) grade b suitable for 110mm bore pipe complete all as specified and directed by engr-in-charge. 114 all as per item no 111 above 115 supply & fixing upvc vent cowl grade b suitable for 110mm bore pipe complete all as specified and directed by engr-in-charge. 116 supply & fixing pvc vent cowl grade b suitable for 75 mm bore pipe complete all as specified and directed by engr-in-charge. 117 supply & fixing upvc grade b multi floor trap 110 mm bore and 600mm long with grating including jointing with with pipe joint lubricant complete all as specified and directed by engr-in-charge. 118 supply & fixing upvc grade b multi floor trap 75 mm bore and 600mm long with grating including jointing with with pipe joint lubricant complete all as specified and directed by engr-in-charge. 119 demolition of brick work built in cement mortar including all quoins, arches, pillars etc . 120 m&l for brick work with subclass‘b’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by engineer-in-charge. 121 labour only forbrick work built in cm (1:6) with subclass b bricks, straight or curved on plan exceeding 6m mean radiuswith reusing the old bricks obtained fromitem no 118 . 122 m&l for taking down carefully point wiring complete including fixture and fittings from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc and making good to disturbed area all as specified 123 m&l for point wiring complete with isi marked 1.5 sqmm single core pvc insulated unsheathed cable 1100v grade frls with multistranded copper conductor drawn through concealed in wall/ceiling surface and its accessories includingpvc rigid concealed conduit heavy duty suitable size with all accessories such as bend, reducers, ms hooks, ms junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switchs, sockets, fan regulator etc covered with 3 mm thick plastic laminated hylem top cover sheet of required color fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer includingfixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly completed for the following all as specified 124 (a)one light point/fan point/exhaust controlled byone way switch 125 (b)one light point controlled by one two way switch 126 (c)one 5 pin socket out let 5 amps on the same board with other switches 127 (d)one 5 pin, 5a switch socket outlet point on independent board with other switches. 128 all as per item no. 02 here-in-before but with 2.5 sqmm cable for 1no 16 amps socket outlet point on independent board including 2.5 sqmm pvc insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor all as specified 129 s&f piano type switch single pole 1 way 5/6 amps 230 volt ac supply complete all as specified and directed by engr-in-charge. 130 s&f socket two in one 6/5 pin 5 amps230 volt ac supply complete all as specified and directed by engr-in-charge. 131 s&f piano type switch single pole 1 way 15/16 amps 230 volt ac supply complete all as specified and directed by engr-in-charge. 132 s&f piano flush type switch single pole 2 way 15 amps 230 volt ac supply complete all as specified and directed by engr-in-charge. 133 s&f socket two in one 6/5 pin 15/16 amps230 volt ac supply complete all as specified and directed by engr-in-charge. 134 s&f ceiling rose surface type, 65mm x 50mm three terminals, 3 phase / pvc / polycarbonate isolated body complete all as specified and directed by engr-in-charge. 135 s & f stepped type electronic fan regulator flush type on the existingphenolic laminated sheet etc. as reqd complete all as pecified and directed. 136 s&f lamp holder, pvc/polycarbonate type with back plate suitable for batten fittings with led bulb 09 watt complete all as specified 137 supply and fixing led lights fitting 20 w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 138 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete. 139 supply and fixing led street light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65/66 protection complete. 140 s&f single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amps capacity complete all as specified and directed by engr-in-charge. 141 s&f sheet metal enclosure for vtpn dbs 415 volts 08 way with 200 amps rated bus bar neautral link, earth bar double door with mccb as incomer complete all as specified 142 s&f sheet metal enclosure for vtpn dbs 415 volts 04 way with 200 amps rated bus bar neautral link, earth bar double door with mcb tpn as incomer complete all as specified and directed by engr-in-charge. 143 s&f sheet metal enclosure for dbs spn 230 volts 12 way with 200 amps rated bus bar neautral link, earth bar double door complete all as specified and directed by engr-in-charge. 144 supply and fixing 415v 16 ka 415 volts mccb of cap 100 amps following poles and current carrying capacity in the db complete with connection testing and commissioning. 145 supply and fixing 415v 10ka b curve miniature circuit breaker (mcb) tpn/4p of capacity 40 to 100 amps poles and current carrying capacity in the db complete with connection testing and commissioning. 146 supply and fixing 240v, 10 ka b curve miniature circuit breaker (mcb) of single poles and current carrying capacity 6 to 32 amp, in the mcb db complete with connection testing and commissioning complete all as specified and directed by engr-in-charge. 147 supply and fixing amp rating 240v, 10ka c curve miniature circuit breaker (mcb) of spn 40 to 63 amp and current carrying capacity in the mcb db complete with connection testing and commissioning complete all as specified 148 m&l forsubmain wiring comprising single core , 2 runs of 2.5 sqmm nominal cross sectional areamulti stranded copper conductor cable, pvc insulated unsheathed 1100 volts gradedrawing in and including appropriate dia. in surface/recessed pvc conduit and its fittings completeincluding provision of 1x2.5 sqmm nominal cross sectional areamulti stranded copper conductor cable, pvc insulated unsheathed 1100 volts grade as earthwire and using color code as per is and specified and making good all disturbed work to match the existing complete incl taking down old unsv sub main complete all as specified and directed by engr-in-charge. note :- (i)extra length of cables/ wire required for connection to mcbs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly.(ii) two run of wire, one run of earth wire and conduct shall be measured as one unit. 149 all as per item no 142 abovebut for single core , 2 runs of 4.0 sqmm nominal cross sectional area including provision of 1x4.0 sqmm nominal cross sectional area complete all as specified and directed by engr-in-charge. 150 all as per item no 142 above but for single core , 2 runs of 6.0 sqmm nominal cross sectional area including provision of 1x 6.0 sqmm nominal cross sectional area complete all as specified and directed by engr-in-charge. 151 m&l for earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 m below normal gl connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washersand earth strip protected by 15 mm dia gi pipe medium grade and connected to main distribution board panel/earthing test point all as shown on electrical plate no.3 of ssr part i and all as specified including testing on completionincluding taking down old unserviceable earthing any type complete all as specified and directed by engr-in-charge. note :-gi wire 4mm dia including test point terminal box include in the quoted rate.

Central Government/Public Sector

TRN :49054201 | 26 May, 2025

Tender Value : 25.00 Lacs

Bakloh - Himachal Pradesh

Tender for tender for certain repair to road and misc works at bakloh cantt; 1 repair to pot holes any depth not exc. 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, path etc. cutting around edges to at least 25mm in depth, making good by filling screened and graded raod metal. watering and ramming applying tack coat @ 10 kg/10 sqm, putting in premixed bituminous premix semi dense asphaltic concrete 40mm consolidated thickness with 5.5% binder content by weight of total mix using 20mm crushed stone aggregate rolled and compacted to required camber and gradient with 8 to 10 tonne power rollerfor depth of pot holes exceeding 30mm complete all as specified and directed. 2 preparing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with power sweeper or compressor to remove all loose dirt etc., applying evenly a priming/ tack coat with bituminous primer using paving bitumenat 5 kg per 10 sq metre of road surface, laying bituminous premix semi dense asphaltic concrete 40mm consolidated thickness with 5.5% bitumen binder content by weight of total mix using 20mm crushed stone aggregate, rolled and compacted to required camber and gradient with 8 to 10 tonne vibrator power roller, complete all as specified and directed. note:- bituminous premix semi dense asphaltic concrete shall be mixed in automatic temperature controlled hot mixing plant, transported and premix carpet shall be laid in single layer with self propelled mechanical paver, rolled with vibrator roller. 3 cat eye two way reflective absbodyof size 100mm x 100mm x 18.5mm with reflective panel (amber red or white) , weight 133 grams fixed with and including ms stud of suitable size as per manufactures instructions complete all as specified and as directed.make: 3m, shakti, darkeye. 4 convex mirror 1000mm dia made out of polycarbonate material provided with suitable ms pipe post duly powder coated, meant for road turning, intersection curve, t-junctions, hospitlas , parking lots etc. with clear and definite mirror image having 130 degree of viewing angle, unbreakable glass, spring post (710 x 80 x 210mm) body of spring is made of special flexile material (polyurethane) without it can be quickly resoted to its original state without doing any damage to spring post as well as vehicle in case of high speed collsion by vehicles. two bands of reflective tape to be pasted on the spring post. eposy bond will beused to fix the spring post with road surace. the bond should be so strong that post will not be deviated by strong impact after installation, length of spring post 710 mm upper dia 80mm & botttom dia is 210 mm, fixed in repair complete all as specified and as directed by engr-in-charge. 5 metal tubular dealineator made out of abs round body fitted with 2 nos 65 mm dia highly reflective reflectors made out of pmma and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermoplastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in pcc 1:2:4 (150x150x300mm) type b1 complete all as specified and directed 6 marking lines, dashes, arrows etc of width 10 cms on black top/ concrete surfaces of road using hot applied thermo plastic road marking paint 2.5 mm thick (white/ gold, yellow) mixed with radium glass beads @ 250gm/ sqm with automatic machine to provide reflectivity and night vision (approx temp being 200°c at the time of laying) including cleaning the surface of all dirt, dust and other foreign material complete all as specified. note:- road marking lines at the centre of road shall not be continuous, whereas the lines at outer sides of road shall be continuous i.e in one length. 7 deduct credit amount as per schedule of credit as details given on srl page no 19 of tender doucments.

corporations/Associations/Others

TRN :49056804 | 23 May, 2025

Tender Value : 18.27 Lacs

Prayagraj - Uttar Pradesh

Tender for tender for annual civil & electrical m&r work for residential building situated at 20-clive road hydel colony, prayagraj - earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. for all kinds of soil. 2 supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. 3 surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. for all kinds of soil. 4 excavating, supplying, stacking and filling of local earth by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 5 providing and laying in position cement concrete of grade 1:1½:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 6 providing and laying in position cement concrete of grade1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 7 providing and laying in position cement concrete of grade 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 8 providing and laying cement concrete 1:1½:3 (1 cement: 1½ coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 9 providing and fixing up to floor five level precast cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering complete. 10 providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 11 extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturers specification. 12 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 13 providing and laying in positiongrade 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 14 providing and laying in positiongrade 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 15 reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 16 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 17 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 18 centering and shuttering including strutting, propping etc. and removal of form for walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 19 centering and shuttering including strutting, propping etc. and removal of form forsuspended floors, roofs, landings, balconies and access platform 20 centering and shuttering including strutting, propping etc. and removal of form for shelves (cast in situ) 21 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 22 centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts 23 centering and shuttering including strutting, propping etc. and removal of form for stairs, (excluding landings) except spiral-staircases 24 centering and shuttering including strutting, propping etc. and removal of form for spiral staircases (including landing) 25 centering and shuttering including strutting, propping etc. and removal of form for small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 26 centering and shuttering including strutting, propping etc. and removal of form for small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like 27 centering and shuttering including strutting, propping etc. and removal of form for weather shade, chajjas, corbels etc., including edges 28 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick 29 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick 30 mild steel and medium tensile steel bars for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 31 mild steel and medium tensile steel bars for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 32 smooth finishing of the exposed surface of r.c.c. work with 6 mm thick cement mortar 1:3 (1 cement : 3 fine sand). 33 add for plaster drip course/ groove in plastered surface or moulding to r.c.c. projections. 34 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) 35 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand) 36 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement : 4 coarse sand) 37 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 (1 cement :4 coarse sand) 38 providing and fixing 18 mm thick granite stone slab of colour black, cherry/ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels (area of slab over 0.50 sqm) 39 providing edge moulding to 18 mm thick granite workcounters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge. 40 extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 41 providing and fixing plywood 4 mm thick, one side decorative veneer conforming to is: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : 42 providing and fixing 4mm thick coir veneer board, isi marked is : 14842, plain lining with necessary screws, priming coat on unexposed surface etc., complete. 43 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 44 providing second class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 45 providing and fixing 2nd class teak wood size 50x12 mm moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 46 providing and fixing second class teak wood panelled or panelled and glazed 30 mm thick shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of engineer-in-charge. (note:- butt hingesand necessary screwsshall be paid separately) 47 providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 48 providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 49 providing and fixing30mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned and chemically treated hollock wood) 50 providing and fixing35mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned selected planks of sheesham wood) 51 providing and fixing30mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned selected planks of sheesham wood) 52 providing and fixing30mm thick panelled or panelled & glazed shutters for cup board using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(second class teak wood including isi marked anodised aluminium butt hinges with necessary screws) 53 providing and fixing isi marked 35mm thick flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 54 providing and fixing isi marked 30mm thick flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 55 providing and fixing isi marked 35mm thick flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 56 extra for providing and fixing flush doors with on one side only decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 (part i) 57 providing and fixing 12mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 58 providing and fixing 20mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 59 providing and fixing 25mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 60 providing and fixing 20mm dia (heavy type) nickel plated m.s. pipe curtain rods with nickel plated brackets : 61 providing and fixing 25mm dia (heavy type) nickel plated m.s. pipe curtain rods with nickel plated brackets : 62 providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. 63 providing and fixing 125x65x2.12 mm isi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 64 providing and fixing 100x58x1.90 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 65 providing and fixing 75x47x1.70 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 66 providing and fixing 50x37x1.50 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 67 providing and fixing 150 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 68 providing and fixing 125 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 69 providing and fixing 100 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 70 providing and fixing 250x16 mm isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete (copper oxidised as per is 1378) 71 providing and 250x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 72 providing and 200x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 73 providing and 150x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 74 providing and 100x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 75 providing and fixing isi marked 85x42 mm oxidised m.s. pull bolt lock conforming to is : 7534 with necessary screws bolts, nut and washers etc. complete (copper oxidised as per is 1378). 76 providing and fixing 125 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 77 providing and fixing 100 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 78 providing and fixing 75 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 79 providing and fixing 150 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 80 providing and fixing 115 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 81 providing and fixing 90 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 82 providing and fixing 300 mm (weighing not less than 330 grams) oxidised m.s. casement stays (straight peg type) with necessary screws etc. complete (copper oxidised as per is 1378) 83 providing and fixing 125mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 84 providing and fixing 100mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 85 providing and fixing 75mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 86 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 87 providing and fixing triple strip vertical type magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 88 providing and fixing double strip (horizontal type) magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 89 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge (extruded section profile size 48x40 mm) 90 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge (extruded section profile size 42x50 mm) 91 providing and fixing 12 mm thick fire retardant plywood conforming to is: 5509 panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 92 providing and fixing cup board shutters 25 mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board is: 12823 marked, exterior grade (grade l type ll), having one side decorative lamination and other side balancing lamination, including iind class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the engineer-in-charge 93 providing and fixing aluminum u beading of required size to pre-laminated/flush door shutter, including fixing etc. complete as per direction of engineer-in-charge. 94 providing and fixing casement handle made of zinc alloyed (white powder coated) for upvc casement window with necessary screws etc. complete. 95 providing and fixing zinc alloyed (white powder coated) touch lock for upvc sliding window with necessary screws etc. complete. 96 providing and fixing steel roller for upvc sliding window with necessary screws etc. complete. 97 providing and fixing steel roller for upvc sliding door with necessary screws etc. complete. 98 providing and fixing steel (white power coated) crescent lock for upvc sliding window/ door with necessary screws etc. complete. 99 providing and fixing 18mm thick both sides pre-laminated cement bonded wood particle board as per is : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of engineer-in-charge (note: fittings to be paid separately). 100 providing and fixing 6mm thick both sides pre-laminated cement bonded wood particle board as per is : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of engineer-in-charge. 101 providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed bwp grade marine ply as per is 710 of approved brand including 2mm thick pvc edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of engineer-in-charge.(payment of providing and fixing auto closing hinges shall be paid separately) 102 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 103 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 104 providing and fixing 1mm thick m.s. sheet door with frame of 40x40x6 mm angle iron and 3 mm m.s. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.(using m.s. angels 40x40x6 mm for diagonal braces) 105 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 106 providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing t-iron frame or to the wall with dash fastener,including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of engineer-in-charge. 107 brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar with 1:6 (1cement : 6 coarse sand) including filling the joints with same mortar, with common burnt clay non modular bricks: 108 dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks. 109 40 mm thick with 20 mm nominal size stone aggregate cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 110 18 mm thick cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 111 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 112 cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. 113 25 mm thick kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 114 deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. 115 fixing glazed/ ceramic/ vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (water based) conforming to is: 15477, in average 3mm thickness. 116 kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 117 providing and fixing 1st quality ceramic glazed floor tiles conforming to is : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 118 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. 119 providing and laying vitrified floor tiles size 600x600 mm(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. 120 providing 1 mm thick with zinc coating not less than 275 gm/ m² corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 121 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over p.v.c. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 122 providing & fixing 0.56 mm, aluminium color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm at all heights, levels and locations colour finish aluminium alloy roofing sheets of alloyis designation31500, temper hx8 conforming to is 737 and dimensions as per is code 2676 with characteristics of good formability and corrosion resistance. the profile sheets shall be fixed to truss members in slope or required pitch or curvature with hex cap headed self drilling/tapping stainless steel screws m6, 50 mm long with 3 mm epdm seal washer etc. all inclusive of labour, scaffolding, t&p and sundries etc. complete as per directions of the engineer-in-charge. (cost of truss/frame work shall be paid separately). 123 providing and fixing precoated/mill finish aluminium ridges plain (500- 600mm) of pre-coated colour or mill finishaluminium roofing accessories in 0.71 mm thickness ,alloy 31500 (is designation) [aluminium alloy (aa) 3004 (iso designation)]for color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping ss screws of size 6 x 50mm with 3mm thick epdm seal and ss plain washer complete : 124 providing 10 mm thick plaster of paris (gypsum anhydrous) flat surfaces ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): 125 12.5 mm thick fully perforated gypsum board tile made from plasterboard having glass fibre conforming to is: 2095 part i, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an nrc (noise reduction coefficient) of 0.79, with 50 mm resin bonded glass wool backing. 126 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) 127 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 128 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) 129 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) 130 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) 131 neat cement punning. 132 distempering with 1st quality acrylic distemper (ready mixed) new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than50 gram/litre of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 133 finishing walls for new work (two or more coats applied @ 3.84 kg/10 sqm) with water proofing cement paint of required shade : 134 finishing walls for new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) with acrylic smooth exterior paint of required shade : 135 finishing walls for new work (two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. with ready mixed premium acrylic emulsion paint (company depot tinted) having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shadewith silicon additives. 136 with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 137 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 138 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) 139 painting (two or more coats) on 100mm diameter rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 140 painting (two or more coats) on 150mm diameter rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 141 painting two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 142 polishing on new wood work with ready mixed wax polish of approved brand and manufacture : 143 lettering with black japan paint of approved brand and manufacture 144 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 145 distempering for old work (one or more coats) with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturerincluding applying additional coats wherever required to achieve even shade and colour 146 applying priming coats with water thinnable cement primer on wall surface having voc content less than 50 grams/litre of approved brand and manufacture. 147 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of engineer-in-charge. 148 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 149 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 150 polishing on old wood work with ready made wax polish of approved brand and manufacture : 151 painting (one or more coats) with black japan paint of approved brand and manufacture to give an even shade. 152 finishing walls for old work (two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface with acrylic smooth exterior paint of required shade : 153 repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 154 fixing door chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 155 fixing chowkhat in existing opening in brick/ rcc wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including cost of dash fasteners/ chemical fastener. 156 making the opening for door/ window/ clerestory window in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of engineer-in-charge. 157 renewing float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) with putty and nails wherever necessary including racking out the old putty: 158 renewing float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) with putty and nails wherever necessary including racking out the old putty: 159 renewal of old putty of glass panes (length) 160 refixing old glass panes with putty and nails 161 fixing old glass panes with wooden fillets (excluding cost of fillets) 162 renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer. 163 pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 164 providing and fixing 20 mm diameter. brass curtain rods ofwall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 165 repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of engineer-in-charge. 166 cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of engineer-in-charge. 167 disconnecting damaged overhead/terrace pvc water storage tankof any size from water supply line and removing from the terrace including shifting at ground level as per direction of engineer-in-charge. 168 providing & fixing orissa pattern w.c pan of size 580x440 mm white vitreous china water closet squatting pan (indian type) along withs or p trap including dismantling of old wc seat and s or p trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. 169 dismantlingw.c.pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of engineer-in-charge. 170 dismantling 15 to 40 mm dia g.i. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of engineer-in-charge.(a) internal work- exposed on wall 171 taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the engineer-in-charge. 172 demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of engineer- in-charge. 173 demolishing nominal cementconcrete 1:3:6 or richer mix (i/c equivalent design mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 174 demolishing nominal cementconcrete 1:4:8 or leaner mix (i/c equivalent design mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 175 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. 176 demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. 177 removing mortar from bricks in from brick work in cement mortar and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): 178 dismantling doors, windows and clerestory windows (steel or wood) shutter of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 179 dismantling doors, windows and clerestory windows (steel or wood) shutter of area beyond 3 sq. metres including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 180 taking out doors, windows and clerestory window shutters (steel or wood) of area 3 sq. metres and belowincluding stacking within 50 metres lead : 181 taking out doors, windows and clerestory window shutters (steel or wood) of area beyond 3 sq. metres including stacking within 50 metres lead : 182 dismantling for thickness of tiles 10 mm to 25 mmwork in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 183 dismantling for thickness of tiles above 25 mm and up to 40 mmwork in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 184 demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : 185 dismantling g.s. sheetroofingincludingridges,hips,valleysandguttersetc., and stacking the material within 50 metres lead of: 186 dismantling asbestos cement sheetroofingincludingridges,hips,valleysandguttersetc., and stacking the material within 50 metres lead of: 187 dismantling tiled roofing with battens, boarding etc. complete includingstackingofserviceablematerialanddisposalofunserviceable material within 50 metres lead. 188 dismantlingbarbedwireorflexiblewireropeinfencingincludingmaking rolls and stacking within 50 metres lead. 189 dismantling40 mm thick precast concrete orstone slabsin walls, partition walls etc. including stacking within 50 metres lead : 190 dismantling40 mm to 75mmthick precast concrete orstone slabsin walls, partition walls etc. including stacking within 50 metres lead : 191 dismantling cement asbestos or other hard board ceiling or partition wallsincludingstackingofserviceablematerialsanddisposalof unserviceable materials within 50 metres lead. 192 dismantling of flushing cistern of all types(c.i./pvc/vitrious china) includingstackingofusefulmaterialsnearthesiteanddisposalofunserviceable materials within 50 metres lead. 193 dismantling old plaster or skirting raking out joints and cleaning the surfaceforplasterincludingdisposalofrubbishtothedumping ground within 50 metres lead. 194 dismantlingaluminium/gypsumpartitions,doors,windows,fixed glazing and false ceiling including disposal of unserviceable material andstackingofserviceablematerialwithin50metersleadas directed by engineer-in-charge. 195 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping groundorasapprovedbyengineer-in-charge,beyond50minitial lead, for all leads including all lifts involved. 196 cuttingroadandmakinggoodthesameincludingsupplyofextra quantities of materials i.e. aggregate, moorum screening, red bajri and labour (required.bituminous portion) 197 paintingroadsurfacemarking for new work (two or more coats) withadequatenosofcoatstogive uniform finish with ready mixed road marking paint conforming to is : 164, on bituminous surface in white/yellow shade, including cleaning thesurfaceofalldirt,scales,oil,greaseandforeignmaterialetc. complete. 198 paintingroadsurfacemarking for old work (one or more coats) withadequatenosofcoatstogive uniform finish with ready mixed road marking paint conforming to is : 164, on bituminous surface in white/yellow shade, including cleaning thesurfaceofalldirt,scales,oil,greaseandforeignmaterialetc. complete. 199 taking out existing cc interlocking paver blocks from footpath/ central verge,includingremovalofrubbishetc.,disposalofunserviceable materialtothedumpingground,forwhichpaymentshallbemade separately and stackingof serviceable materialwithin 50metre lead as per direction of engineer-in-charge. 200 layingoldcementcocreteinterlockingpaverblocksofanydesign/ shapelaidinrequiredline,level,curvature,colourandpatternover and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer- in-charge. (old cc paver blocks shall be supplied by the department free of cost). 201 providing and laying 80mmthickc.c.paverblockofm-35gradewith approved colour design and pattern.factory made chamfered edge cement concrete paverblocksinfootpath,parks,lawns,drivewaysorlighttraffic parkingetc,ofrequiredstrength,thickness&size/shape,madeby tablevibratorymethodusingpumould,laidinrequiredcolour& patternover50mmthickcompactedbedof sand,compactingand properembedding/layingofinterlockingpaverblocksintothesand beddinglayerthroughvibratorycompactionbyusingplatevibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. completeall as per direction of engineer-in-charge. 202 providing andfixingwhitevitreouschinaorissapatternw.c.panofsize 580x440 mm with integral type foot rests waterclosetsquatting pan(indian typew.c. pan)with100mmsandcastironporstrap,10litrelowlevel whitep.v.c.flushingcistern,includingflushpipe,withmanually controlleddevice(handlelever)conformingtois:7231,withall fittingsandfixturescomplete,includingcuttingandmakinggood the walls and floors wherever required: 203 providing and fixing w.c. pan with isi marked white solid plastic seat and lid white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard makeandmosquitoproofcouplingofapprovedmunicipaldesign complete,includingpaintingoffittingsandbrackets,cuttingand making good the walls and floors wherever required : 204 providingandfixing oneurinalbasinwith5litrewhitep.v.c.automaticflushing cistern whitevitreouschinaflatbackorwallcorner typelippedfronturinalbasinof430x260x350mmand 340x410x265 mm sizes respectively with automatic flushing cistern withstandardflushpipeandc.p.brassspreaderswithbrass unions and g.i clamps complete, including painting of fittings and brackets,cuttingandmakinggoodthewallsandfloorswhereverrequired : 205 providingandfixingwhitevitreouschinawashbasinsize550x400mm with a pair of 15 mm c.p. brass pillar taps washbasinwithc.i.brackets,15mmc.p. brasspillartaps,32mmc.p.brasswasteofstandardpattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 206 providing and fixing wash basin with c.i. brackets, 15 mm dia cp brasssingleholebasinmixerofapprovedqualityandmake, including painting of fittings and brackets, cutting and making goodthe walls wherever required:- (a)white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer 207 providingandfixingwhitevitreouschinapedestalforwashbasin completelyrecessedatthebackforthereceptionofpipesand fittings. 208 providing and fixing 610x510 mm bowl depth 200 mm stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required (kitchen sink without drain board) 209 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer - in - charge. 210 providing and fixing 10 litre capacity - white p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete. 211 providing and fixing 10 litre (full flush) capacity-white controlled flush, low level cistern made of vitreous china with all fittings complete. 212 providing and fixing g.i. inlet connection for flush pipe connecting with w.c. pan. 213 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer-in-charge. 214 providing and fixing15 mm nominal dia cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge. 215 providingandfixing 32mm diaflexible pipe p.v.c.wastepipeforsinkorwashbasin including p.v.c. waste fittings complete. 216 providing and fixing 100 mm sand cast iron grating for gully trap. 217 providingandfixinginposition25mmdiametermosquitoproofcoupling of approved municipal design. 218 providing and fixing 600x450 mm beveled edge mirror of superior glass(ofapprovedquality)completewith6mmthickhardboard ground fixed to wooden cleats with c.p. brass screws and washerscomplete. 219 providing andfixing circular shape 450 mm dia mirrorofsuperiorglass(ofapprovedquality)andofrequiredshapeandsizewithplasticmouldedframeof approved make and shade with 6 mm thick hard board backing : 220 providing andfixing 600x120x5 mmglass shelfwith edges round off, supported on anodised aluminium angle frame with c.p. brass bracketsandguardrailcompletefixedwith40mmlongscrews, rawl plugs etc., complete. 221 providing and fixing c.p. brass toilet paper holder : 222 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 223 providing and fixing ptmt towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. 224 providing and fixing ptmt 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 225 providing and fixing ptmt 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 226 providing and fixing ptmt shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. 227 providing and fixing ptmt 15 mm urinal spreader size 95x69x100 mm with 1/2 bsp thread and shapes, weighing not less than 60 gms. 228 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 229 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 230 providing and fixing 25 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 231 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 232 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 233 providing and fixing 25 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 234 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 235 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 236 providing and fixing 25mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 237 providing and fixing 32mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 238 providing and fixing 40mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 239 providing and fixing 50mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 240 providing and fixing 15 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 241 providing and fixing 20 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 242 providing and fixing 25 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 243 providing and fixing 15 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 244 providing and fixing 20 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 245 providing and fixing 25 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 246 providing and fixing 32 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 247 providing and fixing 40 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 248 providing and fixing 50 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 249 providing and fixing 25 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 250 providing and fixing 20 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 251 providing and fixing 32 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 252 providing and fixing 15 mm nominal bore ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 253 providing and fixing 20 mm nominal bore ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 254 providing and fixing 15mm norminal bore 45 cm length uplasticised pvc connection pipe with brass unions : 255 providing and fixing 20mm norminal bore 45 cm length uplasticised pvc connection pipe with brass unions : 256 providing and fixing 100 mm diameter c.p. brass shower rose with 15 or 20 mm inlet : 257 providing and fixing 150 mm diameter c.p. brass shower rose with 15 or 20 mm inlet : 258 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 259 providing and fixing 15 mm nominal bore c.p. brass bib cock of approved quality conforming to is:8931 : 260 providing and fixing 15 mm nominal bore c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 261 providing and fixing 15 mm nominal bore c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms. 262 providing and fixing 15mm nominal bore c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 263 providing and fixing c.p. brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of engineer-in-charge. 264 cutting holes up to 15x15 cm in r.c.c. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 265 providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fastenersto be paid for separately) :(for fixed portion) 266 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fastenersto be paid for separately) :(for fixed portion) 267 providing and fixing glazing with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 268 providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 269 providing and fixing glazing with float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 270 providing and fixing with stainless steel cover plate minimum 1.25 mm thicknessdouble action hydraulic floor spring of approved brand and manufacture conforming to is : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. 271 providing and fixing with brass cover plate minimum 1.25 mm thicknessdouble action hydraulic floor spring of approved brand and manufacture conforming to is : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. 272 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. this layer will be allowed to air cure for 4 hours.(b) second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) 273 providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of fibre glass cloth when the first layer is still green. overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. (for the purpose of measurement the entire treated surface will be measured.) 274 providing & applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer(dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of engineer-in-charge. 275 providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of rcc structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. after cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. over the primed surface swellable type water stop tape shall be placed. the work shall be carried out all complete as per specification and the direction of the engineer-in-charge. the product performance shall carry guarantee for 10 years against any leakage. 276 providing and fixing with15mmthick fullyperforatedsquare/buttedgelightweightcalcium silicate panels/ tiles in position wall panelling at all heights with integral densified calcium silicatepanels/tilesofsize595x595mm,havingnrc(noisereductioncoefficient)of0.50 (minimum) as per is 8225:1987, light reflectance of 85% (minimum). non combustible as per bs:476 (part-4), fire performance as per bs:476 (part 6 &7), humidity resistanceof 100%,thermalconductivity<0.043w/mk asperastm518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mmthickpressedsection(galvanizing@120gramspersqmincludingbothsides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor andceilingchannel sectionofsize50x32mfixedtothefloorandsoffitat600mm centersusing12mmdia,50mmlongwedgetypeexpandedzincalloy dashfastnerwith 10mm bolt. this same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. glasswool of 50mm thickness is then to be inserted in the slots and finallycalcium silicate non combustible panels/tiles are to bescrew fixed withselftapping panheadnickel coatedmild steelscrewsofsize13x3.2mmon tothisgridleavingan evengroove of1 mm betweenthepanels. the joints betweenthepanelsaretobedulyjointedandfinishedusingrecommendedjointing calcium silicate based compound and fiber joint tape roll 50mm wide(90 metre )roll and twocoatsofprimersuitableforpanellingaspermanufacturersspecificationasper direction of engineer-in-charge all complete. 277 providing and fixing with 16 mm thick beveled tegular mineral fibre false ceiling tile (nrc 0.55 to 0.6 mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance (rh) of 99%,lightreflectance=85%,thermalconductivityk=0.052-0.057w/mk,fire performance as per (bs 476 pt - 6 &7)in true horizontal level suspended on interlocking t- grid of hot dipped all round galvanized iron section of 0.33 mmthick (galvanized @120 gsm)comprisingofmaintrunnersof15x32mmoflength3000mm,crosstofsize 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length600mm toform gridmoduleofsize 600x600mm suspendedfrom ceiling using galvanizedmildsteelitem(galvanised@80gsm)50mmlong8mmouterdiameterm-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l- shapeleveladjusterofsize85x25x2mm,spacedat1200mmcentretocentrealong main‘t’.thesystemshouldrestonperipherywalls/partitionswiththehelpofgi perimeter wall angle of size24x24x3000 mm made of 0.40 mm thicksheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry walls.s. screws. the exposed bottom portion of all t-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. the work shall be carriedoutasperspecifications,drawingsandasperdirectionsoftheengineer-in- charge. 278 providingandfixingharddrawnsteelwirefabricofsize75x25mmmeshorother suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 279 fillingofjointsbetweenrccplinthbeam/floorslabandwallpanelofexternalwalls, toilet / bath room / wet areas walls on all floor and parapet wall over roof slab, stair case headroomatthetimeoferectionofgfrgpanelswithgroutrw/equivalentsealant compound after the erection of panelbeforethe infill of concrete in panel cavities and fine finish. this applies for all horizontal and vertical joints between gfrg wall and slab panels. 280 waterproofingtreatmentofverticaljoints(ofexternalsideandinternalside)between doorframe,window&ventilatorframes(onallfoursides)ofouterwalloverthe zycosil/equivalent & zycoprime/equivalent solution already applied (before the installation of door / window / ventilator frames in position) and fine finish with grout rw/equivalent. 281 waterproofingtreatmentofrccsunshadewith zycosil/equivalentwaterproofing solution(1litreofzycosil/equivalent&20litresofwaterstirredfirst&2litresof zycoprime/equivalent addedandstirred (total23litres))till itmeetsthesaturationlevel and testing as per rilem or bywater drops test in which water drops do not absorb but drops remain or rolls. 282 in-filling / sealing of joint between rcc lintel cum sunshade and wall (on external side) in all floors by pushing in grout rw/equivalentin paste form and coving 20 mm x 20 mm after applying a coat of zycosil/equivalent & zycoprime/equivalent solution before cement plastering of top, bottom and sides of rcc sunshade. 283 concreteworkwith40mmgaugebrickballastobtainedfrombreaking brick bats (brick bats supplied by the department free of cost) in proportion of 12:6:1 as in csi no. 5.01 includingcost of all labour, materials, t&p etc required for proper completion of work. 284 brickworkinfoundation&plinthwitholddismantled bricks(suppliedby departmentfreeofcost)andcoarsesand mortarin1:6includingsupply ofallothermaterials,labour,removingmortar&cleaningofold&usedbricks,t&p etc complete. 285 supply and filling brick bat in soak pit including all labour,material and t&petc complete. (for 01 soak pit) 286 supplying & fixing 24 gauge annodized aluminium sheet of approved qualityincludingcutting,wastageandfixingthesameoverthewooden door shutters with nails with all material, labour and t&p 287 providingandfixinginplaceafullheightstoragecabinet450mmdeep made with19 mm thick isi marked plyborad, allinterior surfaces to finishedwithpastingof0.8mmthickmicaandallexteriorsurfacestobe finshed with pasting of 1 mm thick mica of texture and colour as approved byengineerinchargeincludingalllabour,t&p,otheritemslike(butnot limitedto)fevicol,nailsscrews,higes,sliders,doorhandles,multipurpose lockofgodrejorequivalentrateetc.requiredforpropercompletionof works, to be measured interms of front area only. 288 providingandfixingfullheightpartitionwith02nos12mmthickisi marked ply board, all surfaces to finished withf 1 mm thick mica of texture andcolourasapprovedbyengineerinchargeandfixedinpolishedteak woodincludingalllabour,t&p,otheritemslike (butnot limitedto) fevicol, nailsscrews,hinges,sliders,doorhandles,multipurposelockofgodrejor equivalent rate etc. required for proper completion of works, to be measured interms of front area only 289 providingandfixing12mmthickframelesstoughenedglassdoorshutter ofapprovedbrandandmanufacture,includingprovidingandfixingtop& bottom pivot & double acting hydraulic floor spring type fixing arrangement ,doorhandle,lockandstopperetcandmakingnecessaryholesetc.for fixingrequireddoorfittings,allcompleteasperdirectionofengineer-in- charge 290 supply and fixing 6mm thick polycarbonate multiwall sheet ,fixing in position with j or u bolts 10 mm. dia with g.i. limpet & bitumen washers including supply of all materials, labour,wastage. and t&p etc. required for proper completion of the work. 291 providing (12x15) mm section groove in plasterincluding all material, labour andt&p etc. required for proper completion of the work.csi no.11.16 292 2.5 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cccsi no.12.26 293 4.0 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cc csi no. 12.28 294 dismantling ofdry b.o.e. floor and proper stacking of dismantled bricks as per direction of e/c. up to 60 m lead. 295 dismantling and re-laying of dry b.o.e. floor including cost of all labour and t&p required forproper completion of work.(labour rates only) 296 cleaning panes of glass with spirit of caustic soda including supply of all materials,labour and t&p etc.required for proper completion of the work. 297 cleaning of septic tank including disposal of waste out side the uppcl area as per direction of the engineer-in-charge including cost of all labour,t&p etc.required for proper completion of the work. 298 cleaning and opening of chocked w.c./ bath / kithchen pipe line including opening and refixing of chamber cover including washing etc. complete.(analysis based on nbo - 11 25.020. 299 s/laying chicken mesh of (20 mm.)hexagonal heavy quality over roofs of joints of roof as per direction of the engineer - in - charge. 300 cleaning of existing pipe line of different dia. ranging from 4 to 2 dia. including digging trenches and refilling, opening of pipes, cleaning of pipes, cutting, threading, if required fixing and including making good the road, wall etc as directed by the engineer i/c. 301 cleaning of existing water pipe line of different dia up to 2 dia including digging trenches and refilling,opening and cleaning of pipes,cutting,threading,if required fixing and including making good the road and wall etc. as directed by the engineer in charge. 302 cleaning of r.c.c. over head tank up to capacity of one lac. liters and chlorinating with bleaching power mixed to water as per direction of engineer - in - charge complete. 303 supply and mixing bleaching powder in over head tank as required or as directed by engineer - in - charge. 304 attending to petty maintenance service like plumbingservice,welder service, mansion service and carpenter servicerequired as below. (job attending by one no. plumber/welder/mason /carpenter with oneno. helper per hour or part of an hour.) 305 cleaning and sweeping of roof of residence as and when requiredincluding uprooting of rank vegetation and disposal of thegarbage upto 50 m. 306 providing and fixing of 150 mm dia pvc pipeof 6 kg/sqcmwith special such as tee, bend, socket, elbow etc including supply of all labour,material,t & p etc complete required for proper completion of work. 307 providing and laying 75 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 308 providing and laying 90 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 309 providing and laying 110 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 310 making arrangement for sweeping, cleaning of road, lanes in back of houses,collecting refuse of bushes & unwanted plants, vegetations etc. & disposal of all rubbish, materials industbins inside the colony area with engaging atleast one number of sweepers including all labour, t&p,etc.required for completion of work as directed by e/i. 311 making arrangement for sweeping, cleaning of ee,ecd(d), georgetown ,prayagraj office rooms, cleaning of dustbin, toilets , dusting of almirahs,tables etc. using phenyle,dusting cloth etc. and disposal of waste outside office premise in municipal dustbinswith engaging sufficient number ofsweepersincluding all labour, t&p,etc.required for completion of work as directed by e/i.(nsi)(consumable items as phenyle,dusting cloth ,brooms etc shall be provided by the department free of cost.) 312 cleaning of main drain or width more than 300mm including disposal of waste refuses studge out side the boards ara including washing and cleaning by clean water completely as per direction of the e/i. including cost of all labour, t&p etc. required for completion of the work. (csino.20.14) 313 cleaning of main drain or width less than 300mm including disposal of waste refuses studge out side the boards ara including washing and cleaning by clean water completely as per direction of the e/i. including cost of all labour, t&p etc. required for completion of the work. (csino.20.15) nsi sl. no.63 314 operation of tube well daily by a suitable experienced operator continously or in different intervals as per program as per program fixed by engineer-in-charge including opening and closing of valves,changing of fuse wire etc. as requrird for proper running of tube well. (nsi) 315 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc as required..group c 316 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet 317 supplying and fixing of 20 mm of medium class pvc conduit along with accessories in surface/recess including junction box, cutting the wall and making good the same in case of recessed conduit as required. 318 supplying and fixing of 25 mm of medium class pvc conduit along with accessories in surface/recess including junction box,cutting the wall and making good the same in case of recessed conduit as required. 319 wiring for circuit/ submain wiring with 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 320 wiring for circuit/ submain wiring with 2 x 4 sq. mm + 1 x 4 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 321 wiring for circuit/ submain wiring with2 x 6 sq. mm + 1 x 6 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 322 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required . 323 providing and laying earth connection from earth electrode with 6 swg dia g.i. wire in 15 mm dia g.i. pipe from earth electrode including connection with g.i. thimble excavation and re-filling as required. 324 supplying and fixing 5 amps to 32 amps rating,single pole, 240/415 volts, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 325 supplying and fixing 63 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 326 supplying and fixing 40 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 327 supplying and fixing 4 way (4 + 12), double door, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without mcb/rccb/isolator) 328 supplying and fixing of 4 way (4 + 12), double door surface/ recess mounting, vertical type, 415 volts, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs (but without mcbs and incomer ) as required . (note : vertical type mcb tpdb is normally used where 3 phase outlets are required.) 329 wiring for light/ power plug with 2x4 sq. mm frls pvc insulated copper conductor single core cable in surface/ recessed medium class pvc conduit along with 1 no 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. 330 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module (75mmx75mm) 331 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required.3 module (100mmx75mm) 332 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 4 module (125mmx75mm) 333 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 6 module (200mmx75mm) 334 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 8 module (125mmx125mm) 335 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 12 module (200mmx150mm) 336 supplying and drawing following 3 x 2.5 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required. 337 supplying and drawing following 3 x 4 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required.(dsr e&m 2022 1.17.21) 338 rewinding of burnt ceiling fan with approved copper wire including cost of all materials, labour and t&p etc. complete (burnt wirewill not be taken back.) 339 greasing of ceiling fan after cleaning the bearing and shaft withoil / petrol and its testing. 340 supply and fixing of led tube light batten fitting suitable for up to 1 x 22 watt led tube light on surface complete in all respect.(csi no. 28.41) 341 supply of 9 watt led bulb make philips, syska, bajaj etc or its equivalent as directed by e/i. 342 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current (bldc) motor, class of insulation: b, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (cm/m/w) minimum 6.00, air delivery minimum 210 cum/min, 350 rpm (tolerance as per is: 374-2019), thd less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than 2 mega ohm, suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required.(dsr e&m 2022 19.1) 343 supply and fixing of 5 blade exhaust fan ventile air dx 225 mm of havellsor equivalent make including all material, t&p etc required for proper completion of work as approved by engineer in charge.(csi no. 28.38) 344 supply and fixing of 3 blade wall fan ofhavells platina 400 mm or equivalent including all material, t&petc required for proper completion of work as approved by engineer in charge.(csi no. 28.37)

Boards / Undertakings / PSU

TRN :49067628 | 30 May, 2025

Tender Value : 0

Dhanbad - Jharkhand

Tender for purchase of miscellaneous items list attached , laying and jointing pvc pipe. heading , abir /kg (best quality) , alluminiun utensils in kg. (best quality) , baby receiving tray 18”x12” – steel / pc (standard quality) , battery big no. 1050 leak proof / pc (everyday/ nippo/duracell) , battery medium 1035 leak proof/ pc (everyday/ nippo/duracell) , battery small 1015 leak proof / pc (everyday/ nippo/duracell) , battery small 1012 r03 (aaa) leak proof / pc (everyday/ nippo/duracell) , biodegradable bags for120 ltr. bins (pack of 100 pcs) – different colour. / pkt. (standard quality) , biodegradable bags for70 ltr. bins (pack of 100 pcs) – different colour. / pkt. (standard quality) , biodegradable bags for 60 ltr.bins (pack of 100 pcs) – different colour. / pkt. (standard quality) , blade shaving/ pkt of 05 pc. (willkingson /topaz/7o’clock) , bleaching powder / 25kg bag. isi marka , candle 200 gm (6 pc. packet) (standard quality) , coloured paper thin / zista (standard quality) , cup plate set bone china / set of 06 , detecto wall mounted / ft (standard quality) , display white board / sft. (standard quality) , display bord digital electric running/sft , door closer automatic standard– godrej / dorset/ pc , door matt 36”x18”coir / pc (standard quality) , door matt 36”x18”pvc grass type / pc (standard quality) , door matt 36”x18”rubber / pc (standard quality) , door matt 4’x2’ coir/ pc (standard quality) , door matt 4’x2’ pvc grass type (standard quality) , door matt 4’x2’ rubber / pc (standard quality) , four bins set 60 ltr.- different colour with trolley / set (standard quality) , french chalk / pkt. of 400gms (isi marka) , glass (water) set / set of 06 pc. (brocil/trew/xera) , hammer/pc (standard quality) , hawai chappal p.vc. front cut/ pair (standard quality)- rubber sole , hawai chappel different size / pair (relaxo/lakhni/bata/ajanta) - rubber sole , hight scale big size/pc. (standard quality) , hindalium utensil / kg (standard quality) , induction kettle for warm water and tea – 2 ltr. / pc. (standard quality) , induction suspen with cover – 2 ltr. capacity (standard quality) , iron utensils in kg. (standard quality) , g.i. box 60”30”30” 26g per pcs. , lifebouy soap 125gm / pc , liquid handwash 200 ml. (detol/lifeboy/savlon) , lock 50 mm / pc (linkatoot/link round , lock 65 mm/ pc (linkatoot/ link round , match box / pkt of 10 pcs. (home light/ aim) , measuring cup steel 200ml / pc (standard quality) , measuring cup steel 250 ml / pc (standard quality) , measuring cup steel 400ml / pc (standard quality) , mechanical height rod / ft (standard mark) , mixer grinder heavy duty 700 wt./ pc (bajaj/ havels/sumeet) , mosquito coil / pkt.(good night/maxo/mortein) , mosquito repellent machine / pc. – (good night, maxo, mortien, allout) , naphtahline ball / 100 gm pkt. (bengal chemical) , needle cum syringe destroyer 3 ltr./ pc. , nil blue / 900 gms pkt. (robin) , oxygen key / pc. , p.v.c. dustbin25 ltrs. in different colour / pc , plastic stool , donor questionnaire and consent form (new format double page double side printed , plastic chair witharm , plastic chair withoutarm , p.v.c. plastic water drum 100ltr. capacity with cover / pc.- cello, milton , p.v.c. plastic water drum 50ltr. capacity with cover / pc.- cello, milton , plastic bucket 20 ltr. capacity(cello, milton) / pc. , plastic dustbin with cover 60 ltrs./ pc- cello, milton , plastic mug – standard size 1000ml (cello, milton) / pc. , plastic tub 20” diameter best quality (cello, milton) / pc. , plastic waste bins 120 ltr. – different colour / pc. (neelkamal/ supreme ) , pressure cooker 10 ltr. – united, hawkins , prestige / pc , pressure cooker 5 ltr. – united, hawkins, prestige / pc , refill liquid for mosquito repellant / pc- good night, maxo, mortien, allout , rice keeping box – g.i. sheets 24g , 35”x20”x12” with cover / pc. (standard quality) , rice keeping box steel - 26g , 35”x20”x12” with cover / pc. (standard quality) , salai wrench for opening oxygen cylinder 10 inch / pc. (taparia ) , shoe boots different size/pc.(standard make) , shoe plastic/pc. , shoe rack steel big size/pc three self/pvc size- 36”x36”x15” , soda tata / 50 kg. bag (tata) , steel utensils / kg. (standard quality) , sutri / kg. (standard quality) , tea container – 10 ltr.capacity / pc. (maharaja/anapurna) , tools kit (speners, screw drivers set, slyrinch, pliers set + electric tester) / set (toparia) , torch 3 cell bras body (l.e.d.) / pc. (eveready/nippo) , urinal male /female / - steel /pc.- (standard make) adult , vimpowder 1000 gm for washing utensil / kg , wall mounting measuring scale / pc (standard make) , washing powder best quality 1000gm / kg. (ghari/panki/wheel active) , whiting / kg. (standard quality) , antivirus total security compatible for win7, win 8, win 10 with installation. quick heal, bit defender, kaspersky , aphaeresis consent from , aphaeresis register , arch file / pc , attendance register- 24 page per pc (bhakka) , blank c.d per pc (sony) , cartidges for toshiba e-studio 3518 a per pc , cartidges for workcentre pe 220 per pc , cartidges for xerox phaser 3260 , cartidges for xerox phaser 3020 , cartidges h.p 88a per pc (h.p) , cartidges h.p. 12a per pc (h.p) , cartidges toshiba 457per pc , cartidges for xerox versa link b 7035 per pc , cartidges h.p. laser mfp 1200 a per pc (h.p) , cartidges h.p. laser 108 a per pc (h.p) , cartidgesnpg- 76 black canon xerox machine. , cartidgeslaser shot lbp 2900b , cartidges pantum m660n , toner for work centre xerox machine model 415 per pc , toner for work centre xerox workcentre 5020 per pc , drum cartidges of xerox machine , drum of xerox machine with blade , clip file pvc per pc (standard quality) , cover file folding per pc (standard quality) , carbon paper –koresblue/ black , rubber stamp different size per pcs. , marking ink 30ml per pcs. , diet calculation register – 400pages. (standard quality) , dot pen cello griper per pc. (cello/ montex) , envelopbest quality 16”x12” per pc (best paper) , envelopbest quality brown paper 10”x4 ” per pc (best paper) , envelopbest quality brown paper with inside laminated 10”x4” per pc (best paper) , envelop best quality 11”x5 ½” per pc (best paper) , envelop coated with cloth 10”x12” per pc. (best paper) , envelop coated with cloth 12”x15” per pc (best paper) , file guard + file folding withprinted hospital name & monogram on cover long thread (best paper) , flat file standard size per pc. (best paper) , fly leaf cloth binding with monogram – as per our sample per pc. (best paper) , guard file 100 stick per pc. (best paper) , gum700 ml per bottle (camel) , marker pen – different color per pc. , office – t.pin per pkt , online ups- 4 kva2 hour backupwith complete installation – exide, microtech, sukam , online ups with inductive load with ½ hour battery backup.- exide, microtech, sukam , p.v.c. cover file bag per pc (best quality) , paper weight standard per pc. , pen drive for computer – 32 gb per pc. (h.p/sony/sandisk) , pen for white board per pc , pen whitener eraser per pc , pin- bell per pkt. (bell/ kisan) , plastic scale 12” , steel scale 12” , registerleather bond printed hospital name & monogram on cover & 1st page with numbering -06 no. per pc(as per our sample) , registerleather bond printed hospital name & monogram on cover & 1st page with numbering -08 no. per pc (as per our sample) , registerleather bond printed hospital name & monogram on cover & 1st page with numbering -12 no. per pc (as per our sample) , registerleather bond printed hospital name & monogram on cover & 1st page with numbering -20 no. per pc (as per our sample) , registerleather bond printed hospital name & monogram on cover & 1st page with numbering -30 no. per pc (as per our sample) , register component preparation 20 no.(as per our sample) , register component storage 20 no.(as per our sample) , register binding , patient’s cross matching register 20 no. , thalassemia pts. register 20 no. , donor defferal register 20 no. , whole blood stock register 20 no. , blood donor register 20 no. , patient’s grouping register 20 no. , donor gruping register 20 no. , master record register wb 20 no. , blood component stock register 20 no. , tti record register 20 no. , issue record register 20 no. , blood component discard register 20 no. , donor consent form both side printing 100 pcs per book , human whole blood/blood component single side printing book of 100 pcs. , color plastic coated labal crad with adhesive paper size 4”x3”per 100 pcs. , humen whole blood ip 4”x3” (group ayellow/group b pink/ group o blue/ group ab white) per 100 pcs , packed red blood cell concentrated ip 4”x3” (group ayellow/group b pink/ group o blue/ group ab white) per 100 pcs , random donor platelet concentrated ip 4”x3” (group ayellow/group b pink/ group o blue/ group ab white) per 100 pcs , fresh frozenplasma ip 4”x3” (group ayellow/group b pink/ group o blue/ group ab white) per 100 pcs , goods weight machine digital 50gm to 150 kg avove with stand havy duty- brand make per pcs. , stamp ink best quality 700ml per bottle , stamp pad self inking big per pc , stamp pad self inking medium per pc , stamp pad self inking small per pc , staplerbig24/10 per pc (kangaroo) , staplerbig24/6 per pc (kangaroo). , staplerbig24/8 per pc (kangaroo) , stapler pin big24/10 per pkt (kangaroo) , stapler pin big24/6 per pkt (kangaroo) , stapler pin big24/8 per pkt (kangaroo) , tag best quality per bundle , tape cutter per pc machine , white paper d.f.s. best quality per rim(500 sheets) (hanuman/ agro) , white paper s.f.s. best quality per rim (500 sheets)(hanuman /agro) , xerox paper white – a3 75 gsm per pkt (500 sheets) (century star/j.k) , xerox paper white – a4 75 gsm per pkt (500 sheets) (centurystar/j.k.) , xerox paper white – u-1 75 gsm per pkt (500 sheets) (century star/ j.k.) , anaesthetics note form single side printing century white paper– 11 ½” x 8” (book of 100 pc) (century 75gsm) , application cum consent form for sterilization operation book of 2 pages both side b/w (century 75gsm) , bed head ticket form double page both side printing- century white paper – size a3 (book of 100 pcs) (century 75gsm) , blood doner card for blood bank size – 5”x4” (100 pcs) (century 75gsm) , blood doner certificate card – multicolour printing for blood bank size 6”x6” plastic coated paper (100 pcs) (century 75gsm) , blood donor card with printing, best quality paper size 4”x6”(100 pcs) (century 75gsm) , blood donor questionnaire and consent form both side printing for blood bank- size 11 ½” x 8”. (book of 100 pc)(century 75gsm) , blood grouping label card group a, b, o,ab – size 5”x4”with adhesive sticker paper colour (100 pcs) (century 75gsm) , blood report form for blood bank 13”x8” .(book of 100 pcs) (century 75gsm) , born certificate form century white paper size 210mm x 297mm / (book of 100 pcs) (century 75gsm) , client dose sheets (o.s.t.) - century white paper size 210mm x 297mm / (book of 100 pcs) (century 75gsm) , colour paper for blood bag 6”x6” (100 pcs) (century 75gsm) , cross match receipt book with duplicate copy for blood bank (100 original + 100 duplicate) per book (century 75gsm) , death certificate form century white paper size 210mm x 297mm / (book of 100 pcs) (century 75gsm) , department of pathology , obs.& gynae (bedside) – report form size a4 (book of 100pcs) (century 75gsm) , diet chart form a4. (book of 100 pc) (century 75gsm) , discharge ticket in best paper a4 general. (book of 100 pcs) (century 75gsm) , e.o.p.d. slip form century white paper 210mm x 297mm. (book of 100 pc) (century 75gsm) , flex banner multicolor with iron frame per sft.- with fitting (standard make) , flex banner multicolor without iron frame per sft.- with fitting (standard make) , for maternity facility case sheet of multiple coloured book of 11 pages both side as per sample/book (century 75gsm) , haemodialysisbook for patient plastic coated front & back page with 12 page 134mmx210mm (per book) (century 75gsm) , indoor continuation sheets form single side printing century white paper – 11 ½” x 8” (book of 100 pc) (century 75gsm) , injury report form best paper size 12”x7” with triplicate copy printing and winding and triplicate numberingfor surgery (book of 50 pcs) (century 75gsm) , investigation report form century white paper 210mm x 297mm. (book of 100 pc) (century 75gsm) , investigation report form for pathology both side printing – 11 ½” x 8” (book of 100 pc) (century 75gsm) , labor room register book of 100 pages as per sample/book (standard size & make) , medical record & check list for female /male sterilization book of 3 pages both side b/w (century 75gsm) , medico legal form single side printing century white paper for pathology& others departments11 ½”x 8” (book of 100 pc) (century 75gsm) , money receipt book of radiology, pathology, medicine,blood bank, office & others department(100 original + 100 duplicate) (century 75gsm) , monthly diet calculation register chart kitchen (book of 100 pcs) (century 75gsm) , name plate rewriting with materials per inch. stand with fitting (standard quality) , number writing of bed/roomper pcround/sq (standard quality & size 6”) , p.v.c. folder files inside pocket & clip with printing & monogram (per pc) (standard quality) , partograph chart form century white paper size 210mm x 297mm / (book of 100 pcs) (century 75gsm) , patient satisfaction survey-laqshya book of 100 pages b/w (century 75gsm) , pre-anaesthetic record form both side printing on yellow paper (book of 100 pc) (century 75gsm) , radiology report form century white paper 210mm x 297mm. (book of 100 pc) (century 75gsm) , blood requisition form for whole human blood i.p. single side printing- 11 ½ ”x8” for blood bank. (book of 100 pc) (century 75gsm) , risk bond form both side printing – century white paper – 11 ½” x 8” (book of 100 pc) (century 75gsm) , a4 size paper single side printing with paper , a4 size paper both side printing with paper , sign board painting & rewriting with material,iron & wood per sft. (standard quality & paints) , sncu bht format – set of 19 page (per set) black & white (century 75gsm) , sncu bht format colour with pocket plastic coated paper – set of 9 page (per set) (century 75gsm) , stock ledger for store printing & binding as per sample 450 page per pc.(as per our sample) , treatment chart form both side printing century white paper – 11 ½” x 8” (book of 100 pc) (century 75gsm) , wall painting and writing with materials per sft. (standard quality & paints) , wall painting with materials per sft. (standard quality & paints) , x-ray film envelops printed best paper -10 ½”x8 ½” (per 100pc) (standard quality) , x-ray film envelops printed best paper -9”x7” (per 100pc) (standard quality) , x-ray film envelops printed best paper - 12 ½”x10 ½” (per 100pc) (standard quality) , x-ray film envelops printed best paper - 12 ½”x12 ½” (per 100pc) (standard quality) , x-ray film envelops printed best paper - 15 ½”x12 ½”. (per 100pc) (standard quality) , bed sheet 100”x60” exclusive cotton / pc (best quality) , bed sheet 108”x76” exclusive cotton / pc (best quality) , blanket red (weight 2 kg) / pc (best quality) , door for curtain synthetic/cotton printed best quality 48” / 6’x4’ stitching +ring +complete fitting(best quality) , door curtain fancy double layer with stitching +ring +complete fitting– per/ pc. (best quality) , donor questionnaire and consent form (new format double page double side printed , cotton clothes green cashment (dosuti) 46” permtr. (best quality) , markin cloth 48 / permtr. (best quality) , mosquito net cotton full bed size 7’x5’x3’ / pc (best quality) , pillow cover 17”x26” excl. cotton c flap / pc (best quality) , pillow with rubber foam standard size 16”x24” / pc (best quality) , tericot cloth- white / per mtr (best quality) , towel big size 29”x 58” / pc (best quality) , towel hand 15”x25” / pc (best quality) , eye towel green cloth material reusable - per/pc. , leggins reusable green cloth material standard size – per/pc. , surgeon cap reusable green cloth material– per/pc. , waste lillen bag standard size – per/pc. , connection pipe for wash besin /pc (standard make & quality) , drain pipe for wash basin/pc (standard make & quality) , plastic angle cock for bathroom /pc (standard make & quality) , plastic bib/piller cock for bathroom /pc (standard make & quality) , supply & fixing of overhead water tank capacity 2000 ltr. & making a platform with masonry enclosures / pc. , supply fixing & connection of necessary water pipe line including all required accessories size ½” -p/feet, , supply fixing & connection of necessarycpvc water pipe line including all required accessories size ¾ ” -p/feet, , supply fixing & connection of necessarycpvc water pipe line including all required accessories size 1 ¼ ” -p/feet, , supply fixing & connection of necessarycpvc water pipe line including all required accessories size 1 ½” -p/feet, , supply fixing & connection of necessary water pipe line including all required accessories size 1 -p/feet, , supply fixing & connection of necessary water pipe line including all required accessories size 2 -p/feet, , supply fixing & connection of c.p. bib cock/c.p angle cockfor bathroom , supply fixing & connection of doctor c.p. bib cock/c.p angle cockfor bathroom , supply fixing & connection of halfa set , supply fixing & connection of fta/mta size ½” , supply fixing & connection of fta/mta size 1” , supply fixing & connection of fta/mta size1 ½” , supply fixing and connecting of valve – ½” complete set , supply fixing and connecting of valve – ¾” complete set , supply fixing and connecting of valve – 1” complete set , supply fixing and connecting of valve – 2” complete set , supply fixing and connecting of valve – 3” complete set , supply fixing and connecting of valve – 4” complete set , supply fixing installation & connection of wash basine / pc. , supply, fixing & connection of cistern for bathroom / pc. , frame work of anodized material per sqft. , bookcase four door book case,rigid knock down construction, prime quality crca steel – panels & frame. . each door is provided with transparent glass for clear inside vision secured in a metal frame through rubber gasket inside the top of respective compartment & ensures parallel and smooth movement. each door has a scissor mechanism for receding inside the tip of respective compartments. each door has plastic side end caps as handle which is easy to grip epoxy polyester powder coated.(catalogue must be attached with tender) (authorization required) , filling cabinet: four drawer filling cabinet – rigid knock down constructions easy to grip full length handle recess integrated into metal drawer having centralized locking and anti-tipping arrangement to ensure that when one drawer is opened for use, it does not allow other drawers to be opened. high quality precision ball slide.(catalogue must be attached with tender) (authorization required) , high back chair cushioned high back revolving chair, pu moulded cushion seat and back with arm .(catalogue must be attached) (authorization required) (durian/ dumro/ zuari/ neelkamal (authorization required) , high back executive chair: high back executive chair – torsion bar mechanism, single seat & back, high density foam. (catalogue must be attached with tender) (authorization required) (durian/ dumro/ zuari/ neelkamal (authorization required) , medium back chair cushioned medium back revolving chair, pu moulded cushion seat and back with arm.(catalogue must be attached with tender) (authorization required) (durian/ dumro/ zuari/ neelkamal (authorization required) , executive office table- size in mm :- 1800(w) x 900(d)x 750 (h) material ;- block board (19mm) |(make: green ply/century ply/kit ply), is 1659:2004 and termite proof, covered with wood finish laminate thickness i mm (is 2046), set of one side drawers with anti-rust telescopic slider and anti-rust monolithic handle, and central locking facility. other side should have the storage box with two self and have a door with anti-rust handle and lock. all edges to be surrounded by teak bead and polished. (durian/ dumro/ zuari/ neelkamal (authorization required) , office table office steel tablemade of pre-laminated particle board with one side drawer unit , size- 4’x2’ approx. (catalogue must be attached with tender) (authorization required) (durian/ dumro/ zuari/ neelkamal (authorization required) , executive table made of pre-laminated particle board with one side drawer unit , size- 5x3x2.5 approx. (catalogue must be attached with tender)(make- durian/ dumro/ zuari/ neelkamal (authorization required) , sofa set three setter (make- durian/dumro/zuari/ neelkamal) (authorization required) , sofa set single setter (make- durian/dumro/zuari/ neelkamal) (authorization required) , six setter dining table with chari (make- durian/ dumro/ zuari/ neelkamal) (authorization required) , center table (make- durian/ dumro/ zuari/ neelkamal) (authorization required) , coir mattress 6.5 feet. x 3feet. , steel plain almirah – steel almirah. size – 78”x34”x19”x22g with locking systems apoxy coated colour.(catalogue must be attached with tender) (authorization required) , steel rack steel rack of 6shelves, size –height 6’ and panelsize – 72”x36”18” , 4+2 base and head, adjustable with sloted angle.(catalogue must be attached with tender) (authorization required) , three seater chair –black chrome plated.(catalogue must be attached with tender) (authorization required) , three seater chair –silver: chrome plated base. (catalogue must be attached with tender) (authorization required) , training chairs withgood quality and finish : student chair, fixed back, hd foam; prelaminated particle writing board, round crc pipe (catalogue must be attached with tender) (authorization required) , visitors chair with handle: full arm visitors chair, fb/capsule pipe mechanism, pu moulded cushion seat and back, capsule pipe crc base. white terycot cloth full back cover. (catalogue must be attached with tender) (authorization required) , revoling bar stool long size , aluminium partition with acp sheets (standard quality & make) , aluminium partition with glass/particle/jali (standard quality & make) , aluminium sliding for window & doors / sq. ft. (standard quality & make) , bht frame – standard steel / pc (12”x 15” standard make & quality) , carpet material with laying labour charges/sqft. (p.v.c. 1.5 mm standard quality & make) , collapsible gate grill with fitting and fixing/ kg(standard quality) , goods carrying trolley/ pc (standard quality & make) , waste segregation trolley 15 ltrs. foot operated double bucket in different colour / pc , baby cradle m.s. 36”x15”x39” with mattress / pc (authorization required) , back rest / pc (authorization required) , basin stand steel / pc (authorization required) , bed pan – steel / pc (standard size & make) , bed side bowl – steel / pc(22 g 18” standard size & make) , wheel chair (authorization required) , bed side screen fourfold with curtains. (authorization required) , bed side locker (authorization required) , wash basin stand (single)(authorization required) , obstetrics delivery table (3 section) (authorization required) , emergency trolley (authorization required) , dispenser stand with foot pedal (operated by pressing the foot pedal) (authorization required) (22 g 18” standard size & make) , dressing drum seamless15”x12” / pc (authorization required) (22 g 18” standard size & make) , dressing drum seamless 11”x15 / pc (authorization required) (22 g 18” standard size & make) , dressing drum seamless 9”x9” / pc (authorization required) (22 g 18” standard size & make) , iron safety gril for all purpose per sft. , eclamptiabed / pc (authorization required)(22 g 18” standard size & make) , examination couch with three upper box, three sliding drawers ,sliding footstep,b.p. apparatus tray & mattress standard size / pc (authorization required) (22 g 18” standard size & make) , foot rest standard sizem.s. / pc. (authorization required) (22 g 18” standard size & make) , foot step standard double m.s. /pc (authorization required) (22 g 18” standard size & make) , gadda for labour table thickness 3” / pc. (neelkamal/ sleepwel, kaulon) , gynae examination couch. (authorization required) , high end fibrebed semifowler (abs pannel) with mattress , i.v. rodand over bed table 6” wheel with side railing/ pc. (authorization required) , high end fibrebed semifowler (abs pannel) with mattress , i.v. rod / pc (authorization required) , i.v. stand s.s. with plastic base / pc. (authorization required) , instrument tray ss6”x8” with cover / pc (authorization required) , instrument tray ss 10”x12” with cover / pc (authorization required) , instrument tray ss 8”x10”with cover / pc (authorization required) , kidney tray big size / pc. (authorization required) , kidney tray middium size / pc. (authorization required) , kidney tray small size / pc. (authorization required) , labour table s.s. telescopic hydraulic height adjustable with mattress / pc. (authorization required) , mattress high density foam (40 density) – 4” for semifowler bed / pc (neelkamal/ sleepwel) , oxygen cylinder stand cum trolley standard / pc. (authorization required) , p.v.c. dustbin trolley with two wheel standard size 120 ltr. branded in different colour / pc (authorization required) , patient stool m.s. powder coated / pc. (authorization required) , pediatric bed with four sides railing & mattress / pc. (authorization required) , revolving stool with s.s. top. / pc (authorization required) , stretcher trolley approx. dimension 2010mm 1 x570mm w x 810 mm. h trolley made of s.s. tubular frame mounted on 200 mm dia four swivels castors. heavy duty with side railing s.s. , o2 cylinder carriage with mattress. / pc. (authorization required) , trolley instrument s.s. / pc. (authorization required) , trolley instrument s.s./ pc.(authorization required) , trolley medicine s.s. / pc. (authorization required) , trolley waste lilen standard size / pc. (authorization required) , ultra low volume fogger – 4 ltr. – 25000 rpm / pc. (authorization required) , verical blind with fixtures & installation/sqft. (standard quality & make) , weighing machine –paediatrics / pc , weighing machine – adult / pc , x-ray view box led / pc , 1.5 ton inverter split ac copper condenserwith installation/ pc. ( with standard warranty ) (catalogue must be attached with tender) (authorization required) , 2 ton inverter split ac copper condenserwith installation/ pc. ( with standard warranty ) (catalogue must be attached with tender) (authorization required) , d s l r camera – 24 mega pixel or more with high speed usb minimum shutter speed 1/4000 per second storage types sd/sdhc8/sdxc8 memory cards./ pc( with standard warranty ) (catalogue must be attached with tender) (authorization required) , geyser – copper –25 ltr / pc( with standard warranty ) (catalogue must be attached with tender) (authorization required).- - havells, bajaj, voltas , geyser – copper – 15 ltr / pc ( with standard warranty ) (catalogue must be attached with tender) (authorization required) .- - havells, bajaj, voltas , inverter sinewave -1500 va/24 volt with double tubular battery 200 ah complete set–with installation & connection / pc. (authorization required).- microtech exide , led t.v. – 32 inch / pcbrand- sony, samsung, l.g.( with standard warranty ) (catalogue must be attached with tender) (authorization required) , photo copier machine – copy speed - 20 copy / min or above, display – 4line lcd display, warm up time approx 31 seconds or less, paper size – a3, a4, a5 (by-pass tray- a3,a4,a5,a6), memory – 256 mb ram, networking features – yes, resolution- 600dpi ( with standard warranty )/pc.(catalogue must be attached with tender) (authorization required) , photo copier machine – copy speed - 35 copy / min or above, display – 9” colour touch screen, warm up time approx 20 seconds or less, paper size – a3, a4, a5 (by-pass tray- a3,a4,a5,a6) memory –4 gb ram, networking features – yes, secure hdd – 320 gb, cpu – dual core ( with standard warranty ) / pc (catalogue must be attached with tender) (authorization required) , refrigerator – 175 ltr / pc( with standard warranty ) (catalogue must be attached with tender) (authorization required).- l.g. samsung, voltas , refrigerator – 220 ltr. / pc( with standard warranty ) (catalogue must be attached with tender) (authorization required). - l.g. samsung, voltas , refrigerator340 to 350 ltr. / pc( with standard warranty ) (catalogue must be attached with tender) (authorization required). - l.g. samsung, voltas , freezer500 ltr and above /pc (authorization required)- voltas , deep freezer 500 ltr / pc (authorization required) - voltas , supply & fixing of tubular battery for inverter -200 ah,- exide , ups set for computer2kva / pc.- microtech , ups set for computer 1kva / pc. -microtech , ups set for computer 650 va / pc.- microtech , fully automatic washing machine 6 kg –pc( with standard warranty ) (catalogue must be attached with tender) (authorization required) l.g., sumsang , water purifier (r.o.) – 50 lph, 7 stage of purification and water recovery more than 55%. the manufacturer company should have iso 9001 , 14001 certified and service centre in dhanbad ( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , water purifier (u.v.) – technical specification of water storage cooler cum inbuilt purifier :- water storage tank capacity – 120 ltr., no of faucets – 03. (two for cold & one for normal), storage tank material and body material-stainless steel 304, provision of last point purification (uv based), refrigerant- r134a, water recovery – 90-100% , manufacturer should be certified by iso 9001 certification for sales & service and 14001 for manufacturing., certificate of endorsement from indian medical association for manufacturer, and service centre in dhanbad (with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , water purifier r.o. + uv/ess with inbuilt cooling system with grilling , 60 lph, storage capacity – 80 ltr. with 08 stages of purification and water recovery more than 55% . the manufacturer company should have iso 9001 , 14001 certified and service centre in dhanbad ( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , bulb led – 20 watt/ pc. brand- havells, bajaj, surya, crompton, panasonic , chemical earthing installation for machine equipment per pc , copper strip for earthing connection per mtr. , curtain pipe with steel clamp, ring supply & installation / rft. , fan capacitor (condenser) brand- usha/ universal. , glow sine board complete set with all fitting & fixing with material / sft. , hot air blower – electric – 2000 wt. / pc. brand- havells/ roxy/ bajaj/ crompton/ panasonic. , led tube light complete set 20 wt. / set brand- havells/ wipro/ bajaj/ great/ white surya, crompton/ panasonic , led tube light complete set 24 wt. / set. brand- havells/ bajaj/ surya/ great white / crompton/ panasonic , mcb box double pole – 32a with installation / pc. , mcb 32 a with installation / pc. , mcb 15a combind with installation / pc. , 6 a switch with installation / pc. , 6a socket with installation / pc. , 15 a top with installation / pc. , ordinary wire / coil , pedestal fan / pc. brand- havells/usha/khaitan/ bajaj/ polar. , slim led tube light36wt / pc. brand- havells/wipro/ bajaj/ surya/ great white/ panasonic , supply & fixing of battery for u.p.s. 12 volt / 650 va single / pc. - microtech, exide , supply & fixing of wall mounting fan/ pc. brand- havells/usha/khaitan/bajaj/ polar. , supply & fixing of wall mounting stabilizer double phase input to single phase output– 4 kva 90 /volte.- microtech, exide, opto , supply & fixing of wall mounting stabilizer double phase input to single phase output– 5 kva.90 volte. - microtech, exide, opto , supply & fixing of wall mounting stabilizer for a.c. digital 4 kva 90v suitable for 1.5 ton a.c.- microtech, exide, opto , supply & fixing of wall mounting stabilizer for a.c. digital 5 kva 90v suitable for 2 ton a.c. - microtech, exide, opto , supply fixing commissioning with necessary electrical connection of change over 100a /pc. , supply fixing commissioning with necessary electrical connection of change over 200a /pc. , supply fixing commissioning with necessary electrical connection of change over 500a /pc. , supply, fixing & necessary connections of ac box (metal body) complete set with mcb , supply, fixing, commissioning with necessary electrical connection ofbus bar – 100a /pc , supply, fixing, commissioning with necessary electrical connection ofbus bar – 200a /pc , supply, fixing, commissioning with necessary electrical connection ofinsulator / tpn – 100a/ pc , supply, fixing, commissioning with necessary electrical connection ofinsulator / tpn – 32a/ pc , supply, fixing, commissioning with necessary electrical connection ofinsulator / tpn – 63a/ pc , supply, fixing, commissioning with necessary electrical connection ofmain switch – 200a / pc , supply, fixing, commissioning with necessary electrical connection ofmain switch 400apc. , supply, fixing, commissioning with necessary electrical connection ofmain switch 500a per pc. , supply, fixing, commissioning with necessary electrical connection ofmain switch –– 32 a / pc , supply, fixing, commissioning with necessary electrical connection ofmain switch – 63 a / pc , supply, fixing, commissioning with necessary electrical connection ofmain switch –100 a / pc , supply, fixing, commissioning with necessary electrical connection ofopen area shaded bus bar-100a/ pc , supply, fixing, commissioning with necessary electrical connection ofopen area shaded bus-bar-200 a / pc , supply, fixing, commissioning with necessary electrical connection ofopen area shaded bus-bar400a , supply, fixing, commissioning with necessary electrical connection ofopen area shaded bus bar500a , supply, fixing, electrical connection & wall cutting with masonry enclosure ofheavy duty exhaust fan with installation and connection / pc , supply, installation & connection of isolation transformer 10 kva , supply, installation & connection of isolation transformer 5 kva , supply, fixing, commissioning with necessary electrical connection ofisulator /itpn200a/pc. , supply, fixing, commissioning with necessary electrical connection ofisulator /itpn400a/pc. , three phase cable wiring for machine equipments cable size- 25mmm sqmm. p/mtr. , tube light holder / pc , wire copper 3/20per coil , wire copper 7/20 per coil , computer – intel core i5 12th generation processor, ram: minimum 8gb or above, hdd : 01 terabyte or above, dvd writer, monitor – 19.5”, u.p.s. – full set ( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , computer – intel core i5 12th generation processor, ram: minimum 8gb or above, hdd : 01 terabyte or above, dvd writer, monitor – 19.5”, u.p.s. – full set ( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , laptop( core i5 12th gen, 8gb ram or more, 512gb or more ssd) (authorization required) , 2 in 1 laptop – core i5 12th gen, 8gb or more ram/ 128 g ssd/ 12.3 inch with windows 10, display- touch screen, sd card reader, 5 mp (1080p) front camera, 8 mp (1080p) autofocus rear camera, quad hd led backlit pixel sense touch screen display 10 point multi-touch, 3:2 aspect ratio. (authorization required) , printer laser- all in one laser printer (print,scan, copy & fax) , minimum – 33 ppm, memory – 32 mb, processor speed – 266 mhz or above, duty cycle – 10000 or above, paper tray can hold minimum 250 or above, both side copy capacity when both side printed paper inserted to copy, 33.6 kbps fax modem or above ( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , printer laser-single function, minimum –25 ppm or above, memory – 32 mb, processor speed – 266 mhz or above, duty cycle – 10000 or above, paper tray can hold minimum 250 or above ( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , scanner – a4, legal size( with standard warranty )/ pc (catalogue must be attached with tender) (authorization required) , biometric finger print usb scanner suitable for aadhar based scanning , bio matric device (iris sensor)-iris scanner usb for aadhar authentication and ayushmand bharat. great for ayushman bharat yojna. provides faster scanning, larger depth of field, wider scanning angle and zero error rates. single iris scanner – usb. (authorization required) , 4g pocket router all sim supported - all 4g sim supported data card. it provides minimum up to 150 mbps speed.plug and play with intuitive web user interface adds to its smooth operation with up to 32 gb memory support. , bar code scanner-supported symbologies :- ean8, ean13, upca, upce, code 39, code 93, code 128, ean 128, codabar, i, intrleave 2 of 5, matrix 2 of 5, msi and all 1d bar codes. light source: - 650 mm laser, scan speed: - 300 scans/sec. scan type: - single laser , usb mso finger scanner(mini size) -all-in-one solution: superior performance enrollment, verification, and identification. government approved bio-metric fingerprint scanner for instant sim activation of all telecom operators. easy plug & play. no prior software installation required. auto detect in your respective application. , multimedia key board for computer / pc , optical mouse for computer (desktop) / pc , making roti tray g.i sheets 24g 60”x36”x6” per pcs , almirah / cabinent lock -painting. standard quality paints and materials. , almirah / cabinent lock -repairing & painting. standard quality paints and materials. , almirah / cabinent lock -changing. , bed iron- painting. standard quality paints and materials. , bed iron- repairing & painting. standard quality paints and materials. , bed side locker- painting. standard quality paints and materials. , bed side locker- repairing & painting. standard quality paints and materials. , bed side screen - painting. standard quality paints and materials. , bed side screen - repairing & painting. standard quality paints and materials. , cardiac bed - painting. standard quality paints and materials. , cardiac bed - repairing & painting. standard quality paints and materials. , dental chair – painting. standard quality paints and materials. , dental chair – repairing & painting. standard quality paints and materials. , examination table - painting. standard quality paints and materials , examination table - repairing & painting. standard quality paints and materials , file cabinet – painting. standard quality paints and materials. , file cabinet – repairing & painting. standard quality paints and materials. , food carrying trolley - painting. standard quality paints and materials. , food carrying trolley - repairing & painting. standard quality paints and materials. , foot step –painting. standard quality paints and materials. , foot step – repairing & painting. standard quality paints and materials. , steel almirah –painting. standard quality paints and materials. , steel almirah – repairing & painting. standard quality paints and materials. , glass painting . , goods carrying trolley -painting. standard quality paints and materials. , goods carrying trolley - repairing & painting. standard quality paints and materials. , installation of steel rod on metal hooks on the doors & windows for parda. , instrument cabinet – painting. standard quality paints and materials. , instrument cabinet – repairing & painting. standard quality paints and materials. , instrument trolley – painting. standard quality paints and materials. , instrument trolley – repairing & painting. standard quality paints and materials. , iron chair neted 3 seater – painting. standard quality paints and materials. , iron chair neted 3 seater – repairing & painting. standard quality paints and materials. , iron chair neted 5 seater – painting. standard quality paints and materials. , iron chair neted 5 seater – repairing & painting. standard quality paints and materials. , moulded chair 3 seater –painting. standard quality paints and materials. , moulded chair 3 seater – repairing & painting. standard quality paints and materials. , g.i. box painting , moulded chair 4 seater painting. standard quality paints and materials. , moulded chair 4 seater repairing & painting. standard quality paints and materials. , moulded chair 5 seater painting. standard quality paints and materials. , moulded chair 5 seater repairing & painting. standard quality paints and materials. , name plate painting , notice board – repairing , o.t. light stand – painting. standard quality paints and materials. , o.t. light stand – repairing & painting. standard quality paints and materials. , o.t. table – painting. standard quality paints and materials. , o.t. table – repairing & painting. standard quality paints and materials. , orthopaedic table- painting. standard quality paints and materials. , orthopaedic table- repairing & painting. standard quality paints and materials. , oxygen trolley – painting. standard quality paints and materials. , oxygen trolley – repairing & painting. standard quality paints and materials. , repair of aluminum door-fitting, fixing with all materials . , repair of aluminum windows - fitting, fixing with all materials. , repair of collapsible gate grill. , repair of door - fitting, fixing with all materials. (aluminum, wooden) , repair of window glass – fitting, fixing with all materials. (aluminum, wooden) , repair of windows - fitting, fixing with all materials. (aluminum, wooden) , repairing of damage mattress with rexene cover (foam where required) , revolving chair –wheel changing with painting , revolving chair – repairing & wheel changing with painting , revolving stool steel - repairing with painting , saline stand – painting. standard quality paints and materials. , saline stand – repairing & painting. standard quality paints and materials. , steel chair – painting. standard quality paints and materials. , steel chair – repairing & painting. standard quality paints and materials. , steel chair with writing pad – painting. standard quality paints and materials. , steel chair with writing pad – repairing & painting. standard quality paints and materials. , steel table painting. standard quality paints and materials. , steel table repairing & painting. standard quality paints and materials. , stretcher trolley / patient trolley -painting. standard quality paints and materials with wheal changing. , stretcher trolley / patient trolley - repairing & painting. standard quality paints and materials with wheal changing. , stretcher trolley / patient trolley - wheel changing. , stretcher trolley / patient trolley - repairing & wheel changing. , twin almirah – painting. standard quality paints and materials. , twin almirah – repairing & painting. standard quality paints and materials. , roofshading water proof metal sheets repairing per sft. , roofshading water proof metal sheets painting per sft. , inverter point wiring with all accessories per mtr. , necessary point wiring & others for machine equipments with all accessories size of wire –10 sq.mm / mtr. , necessary point wiring & others for machine equipments with all accessories size of wire – 04 sq.mm / mtr. , necessary point wiring & others for machine equipments with all accessories size of wire – 06 sq.mm / mtr. , necessary point wiring & others for machine equipments with all accessories size of wire – 1.5 sq.mm / mtr. , re-installation of a.c. machine including old place wall packing, gas charging etc. complete job , repairing & fitting of ac voltage stabilizer single phase , repairing & fitting of ac voltage stabilizer double phase , three phase cable wiring for machine equipments , cable size – 35 sq.mm per mtr. , three phase cable wiring for machine equipments , cable size – 95 sq.mm per mtr. , three phase cable wiring for machine equipments , cable size – 120 sq.mm per mtr. , three phase cable wiring for machine equipments , cable size – 300 sq.mm per mtr. , three phase cable wiring for machine equipments , cable size – 50 sq.mm per mtr. , necessary point wiring & other, size- 2.5 sq. mm , bowl stand - painting. standard quality paints and materials. , bowl stand - repairing & painting. standard quality paints and materials. , medicine trolley- painting. standard quality paints and materials. , medicine trolley- repairing & painting. standard quality paints and materials. , steel rack big. - painting. standard quality paints and materials. , steel rack big. - repairing & painting. standard quality paints and materials. , steel rack small. - painting. standard quality paints and materials. , steel rack small. - repairing & painting. standard quality paints and materials. , labour table.- painting. standard quality paints and materials. , labour table.- repairing & painting. standard quality paints and materials. , visitor chair with cusuion.-painting. standard quality paints and materials. , visitor chair with cusuion.- repairing & painting. standard quality paints and materials. , revolving chair.- painting. standard quality paints and materials. , revolving chair.- repairing & painting. standard quality paints and materials. , book self almirah - painting. standard quality paints and materials. , book self almirah - repairing & painting. standard quality paints and materials. , steel stool- painting. standard quality paints and materials. , steel stool- repairing & painting. standard quality paints and materials. , over bed table. - painting. standard quality paints and materials. , over bed table. - repairing & painting. standard quality paints and materials. , steel chair - painting. standard quality paints and materials. , steel chair - repairing & painting. standard quality paints and materials. , repairing of – wheel chair , abspanel i.c.u bed.- painting. standard quality paints and materials. , abspanel i.c.u bed.- repairing & painting. standard quality paints and materials. , abs semi flower bed.- painting. standard quality paints and materials. , abs semi flower bed.- repairing & painting. standard quality paints and materials. , abs locker - painting. standard quality paints and materials. , abs locker - repairing & painting. standard quality paints and materials. , baby creadle - painting. standard quality paints and materials. , baby creadle - repairing & painting. standard quality paints and materials. , repairing of online ups – 1 kva , repairing of online ups – 2 kva , repairing of online ups – 4 kva , false ceiling with suitable lights- per/ sq. ft. , ply and sunmika work- per/ sq. ft. , floor carpetting – per/ sq.ft. , venyl flooring- per/ltr. , vertical swinds for window – per/ sq. ft. , draw sheet green cloth material reusable standard size – per/pc. , abdominal sheet green cloth material reusable standard size – per/pc. , roof shading waterproof metal asbestos sheet. – per/ sq. ft. , scissors for cloth cutting (shop scissors) , oxygen regulator , humidfier , perineal sheet green cloth material reusable standard size – per/pc. , surgeon apron green cloth material reusable standard size – per/pc. , surgeon kurta reusable standard size – per/pc. , surgeon pajama reusable standard size – per/pc. , surgeon mask green cloth material reusable standard size – per/pc. , surgeon gown impervious green cloth material reusable standard size – per/pc. , surgeon gown green cloth material reusable standard size – per/pc. , bed side screen curtain set of 3 green cloth material reusable standard size – per set , online ups- 2 kvawith battery 100 ah 6 pcs.with complete installation (excide/ microtech) , online ups- 5 kvawith battery 65 ah 15 pcs.with complete installation (exide, microtech) , online ups battery 100 ah , disposable paper plate big size , disposable glass , ball pen (multi colour) , induction cook-top (prestige, havells, bajaj) 2000w , change over – 625a , m.c.c.b 4k- 625a , ph cable 185sq mm , power d.b pannel fabrication 16 swg sheet 60”x30”x12” with 625a bur bar including painting plinth making internal pannel wiring cable socking etc. , survo control 20 kva (manual) , micro oven ( branded company) , cable tray per feet. (best quality) , battery for ups 60 ah with complete installation (excide/ microtech) (authorization required) , battery for ups 26 ah with complete installation (excide/ microtech) (authorization required) , cartridges for brother toner tn- b021 (original cartridge) , cartridges for xerox machine tn 225 (original cartridge) , cartridges for canon mf 3010 (original cartridge) , cartridges for toshiba toner e studio 2809a (original cartridge) , nebulizer machine (best quality) , fumigation machine (best quality) , stethoscope (best quality)

State Government

TRN :49023607 | 16 May, 2025

Tender Value : 22.62 Lacs

Lucknow - Uttar Pradesh

Tender for tender for construction and renovation work of community center located in sector-d of kanpur road scheme - rcc repairs 2 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge. 3 75mm average thickness 4 50mm average thickness 5 25 mm average thickness 6 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 7 bars upto 12 mm diameter 8 bars above 12 mm diameter 9 drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in rcc beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer-in-charge.upto and including 12mm dia. 10 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect.epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 11 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge.note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 12 25 mm average thickness in 2 layers. 13 50 mm average thickness in 3 layers. 14 providing and laying sbr polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structuralmembers e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of rcc member.note: rates shall be for finished surface area of concrete and shall include the cost of making holes in existing rcc slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved super-plasticiser forrendering concrete as flowable self compacting and sbr polymer but shall exclude cost of reinforcement, bond coat, shear keys, centering and shuttering, strutting, propping etc (payment under this item shall be madeonly after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) 15 50mm thick in grade m 25 with cement content not less than 330 kg per cum 16 75mm thick in grade m 25 with cement content not less than 330 kg per cum 17 100mm thick in grade m 25 with cement content not less than 330 kg per cum 18 providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge.(the payment shall be made on the basis of actual weight of approved grout injected.) 19 epoxy injection grout in concrete/rcc work of approved make 20 providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the engineerin- charge.wooven pvc cloth 21 shotcreting r.c.c. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stoneaggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by engineer- in-chargenote: rates shall include the providing necessary ground wires etc. the levelling gauges, if used, shall be paid for separately. payment under this item shall be made only after proper wet curing has been done and surface hasbeen satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 22 50mm thick in grade m 25 with cement content not less than 330 kg per cum 23 75mm thick in grade m 25 with cement content not less than 330 kg per cum 24 providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of engineer-in-charge. 25 providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 26 mild steel or iron work in plain work such as in r.c.c. or r.b. (when not included in an over all rates ) including bending for proper completion of the workand including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. 27 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 28 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 29 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thic 30 waterproofing and terracing 31 providing and laying in situ five course water proofing treatment with app (atactic polypropylene) modified polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to is : 702, 3rd layer of roofing membrane app modified polymeric membrane 2.0 mm thick of 3.00 kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron hmhdpe film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron hmhdpe film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 33 miscellaneous works 34 providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, includingadditional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia m.s. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with m.s. tubes, m.s. tube challis, m.s. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of engineer-in-charge.note:- (1) the elevational area of the scaffolding shall be measured for payment purpose. (2) the payment will be made once only for execution of all items for such works. 35 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. 36 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 37 cleaning of under ground sump, over head r.c.c. tank ( independent staging) including disposal of slit and rubbish, all as per direction of engineer-in-charge.the cleaning shall consist following operations:-(i) tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits.(ii) entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water.(iii) chlorination of rcc internal surface by liquid chlorine.(iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.(v) finally the surface shall be treated with ultraviolet radiation etc. as per direction of engineer-in-charge. 38 door-window repair 39 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) 40 renewal of old putty of glass panes (length) 41 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead asper direction of engineer - in- charge. 42 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer-in-charge. 43 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar 44 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres 45 casement door double panel with french (false) mullion with zinc alloy (zamak) 3d hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.using r4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above ) x (100 mm& above) & french (false ) mullion (64mm & above) x (60 mm & above). (height above 2.5 metre) 46 toughened glass 12 mm thickness 47 finishing work 48 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 49 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 50 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 51 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 52 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 53 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 54 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 55 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 56 washrooms 57 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 58 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 59 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including isi marked stainless steel butt hinges with necessary screws 60 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 61 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 62 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

State Government

TRN :49051926 | 16 May, 2025

Tender Value : 30.36 Lacs

Panaji - Goa

Tender for construction of hall and supplying gym items for pinto youth club of baradi in velim constituency under mla-lad scheme.--demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead. 2 demolishing cement concrete 1:3:6 or richer mix including disposal of material within 50 m lead. 3 laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement. 4 extra for laterite masonry in all sizes in superstructure from floor i level upto floor v level. 5 12mm cement plaster 1:4 (1 cement : 4 fine sand) 6 providing and fixing 1st quality ceramic glazed wall tiles (johnson somany kajaria ) conforming to is:15622 (thickness to be specified by the manufacture of approved make in all colours shades except burgundy bottle green black of any size as approved by engineer-in-charge in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete.;wall ceramic glazed tiles : 300 x 600 7 providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of johnson somany kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to is: 15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete;dark shades 8 proving and fixing white vitreous china wall hung type (european type) water closet with seat and lid with c.i. brass hinges and rubber fittings with flush valve nelson/ similar fully chromium plated with stop cock wall flanges flush pipe or elbow and vaccum breaker coupling etc. including chair bracket/rag bolts cutting & making good the walls and floors where required and concealed seat support - w.c. pan with white plastic seat and lid 9 providing and fixing brass stop cock (heavy) of approved quality :;15 mm nominal bore 10 providing and fixing brass full way valve (heavy) duty with wheel of approved quality :;20 mm nominal bore 11 providing and fixing p.v.c. connection pipe with brass unions 15 mm nominal bore:;45 cm (18”) length . 12 providing and fixing rigid pvc s.w.r. (soil waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:; 110 mm dia 13 providing and fixing rigid pvc bend (approved make) for s.w.r. pipes including lubricating etc complete bend with door :; 100 mm dia 14 providing and fixing nahani trap of rigid pvc (approved make ) for s.w.r. pipes including lubricating etc complete without door :;110 mm dia 15 providing and fixing nickel chrome plated copper alloy fancy bib cock short body jaquar make or equivalent.confirming to is 8931; 1993;15mm nominal bore 16 providing and fixing chlorinated ployvinyl chloride (cpvc) pipes confirming to is:15778 having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of the engineer-in-charge. concealed work (medium duty sdr 13.5 pipe) including cutting chases and making good the walls etc.;20 mm dia nominal outer dia pipes. 17 providing and fixing hand shower (health faucet) with 8mm dia abs/brass body with double lock 1.00 m long flexible tube (brass plated stainles steel flexible hose) and wall hook of approved quality confirming to is standards. 18 frp (fiber reinforced polymer) frames with wood finish manufacture supply and installation (with anchor fastener) of epee or equivalent goan make frp (fiber reinforced polymer) frame of cross section as per options below with right angle joint and frp (fiber reinforced polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). the core of frame would be filled with seasoned wood as infill material. the slot of frame for door resting will be of suitable width so as to take specified thickness door.the frame will be water proof as well as mild acid/ alkali resistant manufactured in an iso 9001- 2015 certified company.;specified cross section;4” x 2” 19 wood finish wood core frp (fiber reinforced polymer) door shutter. manufacture supply and installation (including accessories as mentioned below) of epee or equivalent goan make frp (fiber reinforced polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood moisture less than 17% wooden styles for top rail and lock rails. frp (fiber reinforced polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) and printed matt having wooden textures used along with uv resistant resin to give the clear texture on the door. the core of shutter will be filled with mr 2nd grade block board. the shutter to be water proof as well as mild acid / alkali resistant manufactured using rv tifac (r v engineering college bangalore & technology information forecasting & assessment council) technology in line with is 13034 1990 test standard in an iso 9001 – 2015certified factory. accessories: i) s. s. hinges 4” - 3 nos ii) s. s. latch - 1 no iii) tower bolt 5” - 2 nos iv) handle 5” - 2 nos;shutter thickness;32mm 20 providing and applying white cement based putty of average thickness 1.00 mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete. 21 applying one coat of cement primer of approved brand and manufacture on wall surface. 22 wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade. 23 painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade. 24 applying priming coat with ready mixed primer of approved brand and manufacture on steel work. 25 providing flat iron hold fast 40 cm including fixing to frame with 10 mm dia bolts nuts and wooden plugs and embeded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size.;40 x 3 mm flat iron hold fast 15 cm long 26 providing and fixing m.s. grill of required pattern in wooden frames of windows etc. with m.s. flats square or round bars with round headed bolts and nuts or by by screws.; plain grill 27 centering & shuttering including strutting propping & removal of forms for :;columns piers pillars aburments posts and struts (square rectangle polygon in plan) 28 centering & shuttering including strutting propping & removal of forms for :;sides and soffits of beams beam haunchings cantilever girders bressumers and lintels plinth beams not exceeding 1m in depth 29 centering & shuttering including strutting propping & removal of forms for :;suspended floors roofs landings shelves & their supports 30 providing and fixing 18 mm thick gang saw cut mirror polished premoulded and prepolished machine cut for kitchen platforms vanity counters window sills facias and similar locations of required size approved shade colour and texture laid over 20 mm thick base cement mortar 1: 4 (1 cement : 4 coarse sand) joints treated with white cement mixed with matching pigment epoxy touch ups including rubbing curing moulding and polishing to edges to give high gloss finish etc. complete at all levels.granite of any colour and shade area of slab over0.50 sqm;jet black 31 providing and laying in position machine batched concrete (bmc) machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering shuttering finishing and reinforcement including admixtures in recommended proportions as per is 9103 to accelerate retard setting of concrete improve workability without impairing the strength and durability as per the direction of the engineer-in-charge. m25 grade of reinforced cement conrete by using 410kg of cement per cu.m. of concrete. all works upto floor v level. 32 providing tmt steel reinforcement bars of (sail tata. vizag jsw steel ltd.) ) (confirming to is 1786 of 1986) for rcc work (conforming to i.s. 1786 of 1986) including bending binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. 33 providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the engineer-in-charge: windows with three sliding shutters using 18 mm series shutters section.;plain glass 34 extra for powder coating with pure polyester powder of shade of required colour on the aluminium section 35 providing and fixing vitreous china wash basin with rs or c.i. brackets painted white 15 mm c.p. brass pillar taps c.p. brass chain with rubber plug 32 mm c.p. brass waste of pattern 32 mm diameter m.i. or c.p. brass trap and union complete including cutting and making good the walls where required.; flat back wash basin size 550 x 400mm with a single 15 mm c.p. brass pillar taps. 36 providing and laying in position cement concrete 1: 2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering shuttering and finishing :;all works upto plinth level 37 providing and fixing astm upvc pipe conforming to astm 2467 with iso 14001 including all upvc plain & brass threaded fittings including jointing of pipes & fittings with one step upvc solvent cement trenching refilling & testing of joints complete as per direction of engineer. external work.;sch-80(blue)/(w hite);40mm outer dia. 38 providing and fixing g.i. chain with g.i. pull. 39 providing woodwork in frames of doors windows clerestory windows trusses & other frames wrought framed and fixed in positon.;second class indian teak wood 40 providing and fixing 38 mm thick panelled glazed or panelled and glazed shutters for doors windows and clerestory window including black enamelled iron butt hinges with necessary screws:;second class indian teak wood 41 applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete. 42 painting two or more coats (excluding priming coat) with superior quality ready mixed paint for wood work of approved brand & manufacture in all shades on new work to give an even shade. 43 providing & fixing chromium plated brass tower bolts (barrel type) with necessary screws complete.;250 x 10 mm 44 providing and fixing chromium plated brass sliding door bolt with bolts nuts and screws etc. complete.;300 x 16 mm 45 provided and fixing 150 mm chromium plated brass floor door stopper with rubber cushion screws etc. to suit shutters thickness complete. 46 provided and fixing chromium plated brass 100mm. mortice latch and a pair of levers and handles with necessary screws etc. complete (indian make of approved quality). 47 providing and and laying vitrified floor tiles in different sizes of johnson somany kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigment etc. complete;600 x 600 mm light shades 48 false ceiling:-;providing & fixing false ceiling yashashri make or equivalent made out of 2” x 1” m.s sq tube frame support structure & 20mm x 155mm x 1.2mm multi- cavity upvc section 30mm x 40mm x 2mm upvc multi-cavity section with hidden screwing system.the average weight of false ceiling is 8.50 kg per sq mtr. these upvc sections are tested by using bs 2782 & din 53459 test methods. 49 providing & fixing of aluminium lay-in perforated tile ceiling on 24 /14 mm ‘t’ framework of module 600mm x 600mm. tiles of size 575mm x 575mm / 584mm x584mm made out of 0.6mm thick aluminium. perforation of the tiles shall be 2.5mm dia 5.5mm c/c. the tile shall be manufactured on advanced equipment which includes several levelling. the tile end shall be raised upward by 38mm and bend outward to lay the tile in framework. the tile shall be polyester based powder coated in white colour. grid system for fixing ceiling tiles shall comprise of tees. the 24 /14 mm main tee runners shall be suspended at an interval of 1200mm centre to centre. the 24 /14 mm cross tee runner shall be suspended at 600mm centre to centre and further supported with 24 /14 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x 600mm. the main tee shall be supported by means of 4mm g.i. rod from slab/roof. the suspension shall be provided at 1200 to 1500mm centre to centre.tee framework would be made of gi and powder coated. acoustic felt: non- woven felt made of glass-r einforced fibre glued over the perforation for sound absorption. 50 providing water proofing treatment over the new r.c.c. roofs terrace toilet by spreading cement slurry over the r.c.c. slab and laying of 10cms. average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of hindustan water proofing co. or equivalent jointless water proofing plaster of mix 1:3 ( 1 cement : 3 find sand) finished smooth with wooden trowel with false marking of 30 cms square. the vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. the injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb cracks etc. in the r.c.c. slabs). note: cement consumption 25 kg/sq.m. 51 providing & fixing colour coated alluminium (puf) sandwich panel roofing systems of approved make adhering to aluminium 3105 grade for top & bottom sheet of thickness0.40 & 0.35 respectively including puf insulation betewwn the top & bottom sheet of denslity 40 (+/-2) kg/m3 inclusive of s.s. 304 grade self tapping fastneres complete as directed by enigneer incharge (frame work for roof roof accesorries to be paid seperately) for tile design puf roof panel gutter width should be atleast 25% more than the crest width. minimum height at heighest point of crest should be minimum 65mm. minimum thickness at anygiven point should not be below 30mm.;puf insulated tile roof 30mm thick of trapezoidal design 52 steel work in built up tubular (round square or rectangular hollow tubes etc.) (square hollow section (shs) is4923 /rectangular hollow section (rhs) is4923/circular hollow section (chs) is1161 closed structural steel of (sail tata. vizag jsw apollo steel ltd.) make (min yeild stress 310 mpa)) trusses etc. including cutting hoisting fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc. complete. 53 providing and fixing in position s.s. hand rail in main stair case and landing as per approved design shown in the drawing including bending handrail pipe to proper shape in curves with specials etc. complete. 54 melamine polishing on wood work (one or more coat);glossy 55 providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the engineer-in-charge: adjustable louvered window s.;figured glass 56 extra for powder coating with pure polyester powder of shade of required colour on the aluminium section 57 6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand) 58 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. 59 painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as dulex/ asian paints/ sherwin willians) including applying one coat of cement primer and one coat of surface treatment etc. complete. 60 painting one or more coats of acryllic exterior paint of approved brand and manuf acture(such as dulex/ asian paints/ sherwin willians) on old work including cleaning the surface with water etc. complete. 61 providing & fixing alluminium ridge of approved make adhering to alluminium 3105 grade of 0.71mm thickness & 60 cm wide inclusive of ss304 grade self tapping fastners to match the alluminium roofing system & as directed by engineer in charge complete 62 providing & fixing alluminium 30mm trapezhoidal end cap for puf roofing of approved make of alluminium aa 3105 grade matching with 30mm puf panel profile including the required fastners etc. complete for alluminium puf roofing system & as directed by engineer in charge. 63 pvc wall paneling : providing and fixing pvc sheet wall paneling of thickness 5mm (±0.25) consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm (±0.25) thick prelam pvc sheet.the panel & strips shall be of 600 kg/cbm density manufactured by an iso-9000 certified company. the strips should have in their center a grove of 6mm width and 1mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval of 10” between two pvc strips. the pvc strips shall be fixed to the wall using 65mm long m.s. screws through the groove in the strip by using pvc fasteners. the distance between two screws shall not be more than 200mm. a groove of 2mm may be left at the joint of two panels for aesthetic looks. the exact size of the panel and correspondingly of the grid may vary depending on the size of the wall.optionally a strips of 5mm (±0.25) thick pvc sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined using solvent cement. 64 providing and installing rubber dumbells of hexagonal shape and approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 65 providing and installing barbell rod 5ft of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 66 providing and installing skipping rope of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 67 providing and installing yoga mat 6mm thick of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 68 providing and installing punching bag of 900mm diameter of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 69 providing and installing bench press multidegree of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 70 providing and installing rowing machine of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 71 providing and installing rubber plates of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. a)2.50 kg 72 providing and installing rubber plates of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. b) 5.00 kg 73 providing and installing rubber plates of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. c) 7.50 kg 74 providing and installing rubber plates of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. d)10.00 kg 75 providing and installing rubber plates of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. e)12.50 kg 76 providing and installing rubber plates of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. e) 15.00kg 77 providing and installing dumbell rack of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 78 providing and installing kettle bell of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. a) 2.00 kg 79 providing and installing kettle bell of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. b) 4.00 kg 80 providing and installing kettle bell of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. c) 6.00 kg 81 providing and installing kettle bell of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. d) 8.00 kg 82 providing and installing kettle bell of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. e) 10.00kg 83 providing and installing gym ball 65cms of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 84 providing and installing gym ball 75cms of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 85 providing and installing push up bar with chrome finish of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 86 providing and installing ab wheel roller finish of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 87 providing and installing foam roller finish of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge. 88 providing and installing air bike of approved make including all material, labour, transportation, etc. complete as directed by engineer in charge.

State Government

TRN :49052580 | 22 May, 2025

Tender Value : 27.43 Lacs

S.A.S Nagar - Punjab

Tender for providing and supplying of glassware items for bacteriological section at 7 labs providing and supplying of glassware items for bacteriological section at 7 labs 1 regional advance water testing lab state lab sas nagar and 6 regional water testing labs sas nagar, amritsar, patiala, moga, hoshiarpur and sangrur , glass rod , petri plate , glass slides , microsopic slide slip cover , screw cap bottle (reagent bottle) , volumetric flask , conical flask , beaker , measuring cylinder , measuring cylinder , screw cap bottle (reagent bottle) , eppendorf tube , spatula , spatula , autoclavable glass bottle for collection of microbiological samples

State Government

TRN :49053455 | 16 May, 2025

Tender Value : 17.73 Lacs

Bulandshahar - Uttar Pradesh

Tender for tender for networking lan work at 04 family court at district court bulandshahar - supply installation testing and commissioning of layer 3 switch 24 port 1g sfp port + 2 10ge sfp+ ports. complete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 2 supply installation testing and commissioning of 1g fiber transceiver. complete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 3 supply installation testing and commissioning of layer 2 switch 24 ports 10/100/1000mbps + 2 x 10g sfp l2 switchcomplete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 4 supply installation testing and commissioning of layer 2 poe switch 8 ports 10/100/1000mbps + 2 x 1g sfp l2 switchcomplete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 5 supply and laying of 6 core single mode ofc, armouredcomplete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 6 supply installation testing and commissioning of pig tail 1 mt., sc type, pigtail sc mm (62.5um) simplex length- 1m complete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 7 supply installation testing and commissioning of liu, 12 port, sc type, liu 12 port rack mount. complete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 8 supply installation testing and commissioning of liu, 24 port, rack mount. complete in all respect as per direction engineer in charge. make - cisco/ extreme /dell 9 supply installation testing and commissioning of ofc patch cord, 1 mt., sc-sc / sc lc type patch cord - 1m. complete in all respect as per direction engineer in charge. make- molex/beldon or equivalent 10 supplying and drawing of utp 4 pair cat-6 lan 1 run of cable in the existing surface/recessed steel/pvc conduit as required. 11 supply installation testing and commissioning of cat6 utp patch cord, 1 mt. cat6 utp 24awg patch cord:1m complete in all respect as per direction engineer in charge. make- molex/beldon or equivalent 12 supply installation testing and commissioning of cat6 utp patch panel, 24 port, fully loaded patch panel cat 6 utp keystone type- 24 portfully loaded. make- molex/beldon or equivalent 13 supply installation testing and commissioning of cat6 single modular i/o with back box jack cat 6 keystone utp. complete in all respect as per direction engineer in charge. make- molex/beldon or equivalent. 14 supply installation testing and commissioning of rack - 12uwall mount 12u x 500 w x 450 d, front glass door with lock, 2 pairs of 19 mounting rails: -standard accessories: - 1u cable manager, roof mounted fan unit / 90 cfm /230v ac,6 way 5 amp power distribution unit, mounting ardware.complete in all respect as per direction engineer in charge. makecomrack/rackomor equivalent 15 supply installation testing and commissioning of rack for first floor switches - 24u front glassdoor with lock, 2 pairs of 19 mounting rails: -standard accessories: - 1u cable manager, roof mounted fan unit / 90 cfm /230v ac,6 way 5 amp power distribution unit, mounting hardware complete in all respect as per direction engineer in charge. makecomrack/rackomor equivalent 16 supply and fixing of 25mm size of heavy duty pvc conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required as per direction engineer in charge. 17 supply installtion testing of ups 6 kva capacity with 60mm power back up 60 minutes. complete in all respect as per direction engineer in charge.( make:-delta, epc/bpe 01 no.)

State Government

TRN :49053871 | 14 May, 2025

Tender Value : 0

Anantnag - Jammu And Kashmir

Tender for stage contract for sub division anantnag.- stage contract anantnag sub division. 2 engagements of jcbfor execuation of works of various natures 3 surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -all kinds of soil 4 earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed,( all kinds of soil) 5 earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by engineer-in-charge. all kinds of soil : 6 earth work in excavation by manualmeans in trenches for foundations, drains, pipes, cables etc .upto required depth ) and for shafts, wells, cesspits including dressing of sides and ramming of bottoms , including getting out excavated earth and disposal of surplus excavated earth as directed,( all kinds of soil) 7 supply and filling of rbm of specified size including spreading, watering, ramming, compacting with prr of 8 to 10 tonne capacity and including carriage of the same from approved source upto site of work complete 8 felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. 9 beyond 30 cm girth upto and including 60 cm girth. 10 beyond 60 cm girth upto and including 120 cm girth. 11 beyond 120 cm girth upto and including 240 cm girth. 12 banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m in all kinds of soi 13 supply and filling of khak bajri including spreading, watering, ramming, compacting with prr of 8 to 10 tonne capacityincluding carriage of the same from approved source upto site of work complete( for berm) 14 providing / laying of rcc pipes in proper position/ grade including cutting of road surface upto required depth, providing requisite cushion including carriage ofall materials and pipesupto site ofwork complete. 15 10 16 12 17 14 18 16 19 20 20 24 21 32 22 36 23 40 24 48 25 providing / laying of ms pipes in proper position/ grade including cutting of road surface upto required depth, providing requisite cushion including carriage ofall materials and pipesupto site ofwork complete. 26 6 27 8 28 10 29 12 30 scarifying the existing bituminous road surface to a depth of 50mm and disposal of scarified material within all lifts and lead upto 1 km (by mechanical means). 31 scarifying metalled (water-bound) road surface including disposal of rubbish lead upto 50m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity. 32 providing and laying water bound macadam base course with quarry crushed stone aggregate 90 to 45mm size, stone screening 13.20mm size and binding material as per morth specification including screening, sorting, spreading to template and consolidation with prr of 8 to 10 tonne capacity including carriageofquarry crushedstone aggrregateand stone screeing, stone dustfrom approved soucrce upto site of wotk complete(finished work to be measured) 100mm compacted thickness 33 providing and laying water bound macadam base course with quarry crushed stone aggregate 63 to 45mm size, stone screening 13.20mm size and binding material as per morth specification including screening, sorting, spreading to template and consolidation with prr of 8 to 10 tonne capacity including carriageofquarry crushedstone aggrregateand stone screeing, stone dustfrom approved soucrce upto site of wotk complete(finished work to be measured) 75mm compacted thickness 34 providing and laying water bound macadam base course with quarry crushed stone aggregate 53 to 22.4mm size, stone screening 11.20mm size and binding material as per morth specification including screening, sorting, spreading to template and consolidation with prr of 8 to 10 tonne capacity including carriageofquarry crushedstone aggrregateand stone screeing, stone dustfrom approved soucrce upto site of wotk complete(finished work to be measured) 75mm compacted thickness 35 providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (wmm) specification including premixing the material with water at omc in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of engineer-in-charge 36 providing and applying tack coat using hot straight run bitumen of grade –vg-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. on bitumen surface @ 0.50 kg/sqm 37 providing and applying tack coat using hot straight run bitumen of grade –vg-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. on w.b.m. @ 0.75 kg/sqm 38 providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of engineer-in-charge. 50 to 100 mm average compacted thickness with bitumen of grade vg-10 @ 3.5% (percentage by weight of total mix) 39 providing and laying semi- dense bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of engineer-in-charge. 25 mm compacted thickness with bitumen of grade vg 10 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) 40 providing and laying dense graded bituminous macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of engineer-in-charge. 16.62.1 50 to 100 mm average compacted thickness with bitumen of grade vg-30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) prepared in batch type hot mix plant of 100-120 tph capacity. 16.62.2 50 to 100 mm average compacted thickness with bitumen of grade vg-30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of aggregate) prepared in drum type hot mix plant of 60-90 tph capacity. 41 providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade vg-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete. 42 providing and laying of stone soling, hand packed, including carriage of same from approved source upto site of work complete. 43 providing and laying in position cement concrete in1 : 4 : 8 (1 cement :4 coarse sand : 8 graded crushed stone aggregate, 40mm nominal size) excluding the cost of centering and shuttering but including carriage of all materials from approved sources up to site of work complete. 44 providing and laying in position cement concrete in1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate, 40mm nominal size) excluding the cost of centering and shuttering but including carriage of all materials from approved sources up to site of work complete. 45 providing and laying in position cement concrete in1 : 2 : 4 (1 cement :2 coarse sand : 4 graded crushed stone aggregate, 20mm nominal size) excluding the cost of centering and shuttering but including carriage of all materials from approved sources up to site of work complete. 46 providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. but including carriage of all materials from approved sources up to site of work complete.all works upto plinth level (1: 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 47 providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. but including carriage of all materials from approved sources up to site of work complete.all works upto plinth level (1 : 2 : 4 (1 cement :2 coarse sand : 4 graded crushed stone aggregate, 20mm nominal size)) 48 reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.but including carriage of all materials from approved sources up to site of work complete. (1: 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 49 reinforcement for rcc work including straightening cutting, bending, placing in position and binding all complete (thermo mechanically treated bars) including all carriages complete. fe-500 d or more 50 providing / fixing of necessary farm work / shuttering including strutting, propping etc and removal of same complete 51 foundations, footings, bases for columns 52 return walls, walls (any thickness) including attached pilaster buttresses, plinth and string course fillets, kerbs and steps etc. 53 suspended floors, roofings, landings, balcones and access plateform 54 50mm thick cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished wit a floating coat of neat cement including carriage of all materials from approved sources upto site of work complete 55 40mm thick cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished wit a floating coat of neat cement including carriage of all materials from approved sources upto site of work complete 56 25mm thick cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished wit a floating coat of neat cement including carriage of all materials from approved sources upto site of work complete 57 12mm cement plaster of mix 1:4 (1cement: 4 fine sand) including all carriages complete. 58 12mm cement plaster of mix 1:6 (1cement: 6 fine sand) including all carriages complete. 59 15mm cement plaster of mix 1:4 (1cement: 4 fine sand) including all carriages complete. 60 15mm cement plaster of mix 1:6 (1cement: 6 fine sand) including all carriages complete. 61 dry random rubble masonry in 100 x100mm mesh size g.i wire crate made of 5mm dia g.i wire using bond stones ncluding wrapping /tightening of wire crate and binding wire crates after stone work including cost of all material involed (crates and stones) and carriage of same upto site work complete (quarry stones) 62 random rubble masonry with hard stone (quarry) in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement : 6 coarsesand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of all materials from approved sources up to site of work complete. 63 engagement of labour /masdoor for one day 64 engagement of skilled labour with all machinary like cutters , axe etc for purning of the trees 65 pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 66 removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive 67 clearance of slipsdisposal lead upto 50 m and lift upto 1.5 m. 68 in ordinary soils disposal lead upto 50 m and lift upto 1.5 m. 69 in soils; mixed with moorum/kankar/shingle/boulders; disposal lead upto 50 m and lift upto 1.5 m. 70 in soils; mixed with decomposed rocks; by blasting or any other means 71 providing and applying 2.5mm thick road marking strips (retro-reflective) of specified shade/colour using hot thermoplastic material by fully/semiautomatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, t&p, cleaning the road surface of all dirt, seals, oil, grease and foreignmaterial etc. complete as per direction of engineer-in-charge and accordance with applicable specifications. 72 white washing with lime to give an even shade :old work (two or more coats) 73 white washing with lime to give an even shade :old work (one or more coats) 74 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work 75 painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to is: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.old work ( one or more coats) 76 providing and laying at or near ground level factory made kerb stone of m-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of engineer-incharge (length of finished kerb edging shall be measured for payment). (precast c.c. kerb stone shall be approved by engineer-in-charge). 77 manufacturing supplying and fixing retro reflective sign boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type-iv of astm-d-4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per irc : 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of astm-d-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20cm c/c to back support frame of m.s. angle iron of size 25x25x3mm along with theft resistant measures mounted and fixed with 2 nos. m.s. angles of size 35x35x5mm to a vertical post made upto m.s. tee section ismt 50x50x6mm welded with 16.0 (road work) 224 base plate of size 100x100x5mm at the bottom end and including making holes in pipes, angle flats, providing and fixing m.s. message plate of required size steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical m.s.-tee support to be painted in black and white colours). backside of aluminum sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coats including all leads and lifts etc. complete as per drawing, specification and direction of engineer-in-charge. 16.66.1 mandatory/regulatory sign boards of 900 mm diameter with part as length of 3750 mm. 78 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete 79 structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. welded 80 supply and filling of rbm of specified grade including spreading, watering, ramming, compacting with prr of 8 to 10 tonne capacity material availabe at site

State Government

TRN :49054033 | 15 May, 2025

Tender Value : 0

Challakere - Karnataka

Tender for supply of materials for construction of bhoojanalaya to govt. primary school at mitlakatte village in challakere taluk - mtk add hom of welding and grinding machine at 2% on material,mtk tools & plants and electrical charges at 2%,miscellaneous /contingencies charges,display board or cib,mtk add white lead paint, gasket, cement, sand for making good the wall and floor at 2% on material,mtk licenced plumber with tools,mtk lead or pvc connection pipe 32mm dia (for wash basin),mtk c.i. m.s. brackets for flushing cistern,mtk brass stop cock,mtk cp brass waste 32 mm of standard pattern,mtk cp brass chain with plug,mtk copper plated brass piller tap 15mm,mtk white vitreous china clay flat back wash basin size 630x450mm,mtk handling loading and unloading 3% on material,mtk labour charges for lifting and placing in position and making connection at 7% on material,mtk polyenthylene water storage tank of specified capacity l,mtk vitrified tiles 600x600 mm,mtk fabricator,mtk add 15% wastage for glass,mtk 5.50 mm thick plain glass,mtk chrominum plated screws,mtk cleat angles,mtk alluminium handles - 15 mm,mtk alluminium tower bolt - 20 cm,mtk pvc beading,mtk rubber beading for shutters beading,mtk nylon rollers,mtk aluminium window frame section 1.20 mm thick,mtk binding wire,mtk tmt bars fe 500,mtk add brush, putty, glue at 5% on cost of paint,mtk whitening,mtk dry distemper,mtk unit cost as per the specification,mtk add brush at 1% on cost of paint,mtk enamel metal paint,mtk painter class i,mtk add wire brush, fine steel wool, putty, sand paper, at 3% on cost of paint,mtk ready mix primer paint (ready mix red lead paint),mtk hom of cutting and grinding machine,mtk add,mtk hom of welding and grinding machine,mtk welder grade i,mtk corbon electrodes,mtk anchor bolts 750mm,mtk base plate / base plate,mtk gusset plates 6 mm thick,mtk ms angle iron 40mm x 40mm x 6mm, 23 metre in length at 3.5 kg per metre,mtk ms angle iron 50mm x 50mm x 6mm, 33.8 metre in length at 4.5 kg per metre,mtk add providing and removing scaffolding at 3% on labour,mtk hom of vibrator 0.71 days,mtk plasticizer / super plasticizer,mtk add handling , loading and unloading at 1% on material,mtk solid concrete blocks (40 x 15 x 20 cms)-4.00 n/sqmm,mtk add watering charges at 1 % on labour,mtk stone chistler class ii,mtk mason class ii (with tools),mtk mason class i (with tools),mtk mixer (concrete small used in culvert),mtk boulders,mtk bond stone 20 x 20 x 45 cm,mtk size stone 20 x 20 x 25 cms,mtk add handling , loading and unloading at 2% on material,mtk casurina poles 100 - 150 mm,mtk silver oak or equivalent planks 38 mm thick,mtk add watering charges at 1 % on material,mtk mixer (concrete) - 1 cum capacity,mtk portland cement,mtk coarse sand (zone iii),mtk broken stone aggregate 12 mm to 10 mm size,mtk broken stone aggregate 20 mm size,mtk broken stone aggregate 40 mm size

Related Searched Keywords : sun screen glass

List of sun-screen-glass Tenders

Get sun screen glass Tender Alert...

Related Searched Keywords : sun screen glass

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us