Filters

List of plastic-shutters Tenders

List of latest plastic-shutters Tenders in Indian Tenders. Click on any plastic-shutters Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for plastic-shutters Tenders.

All-Tenders (34)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Cooperative

TRN :49061171 | 15 May, 2025

Tender Value : 3.93 Crore

Visakhapatnam - Andhra Pradesh

Tender for tender for interior works for display corridor from aob entrance east and south to chairperson and dy. chairperson corridor at visakhapatnam port authority, visakhapatnam.; 1 1.1.18 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. cum 1 27.95 494.10 13,807.62 2 2.6.1 earth work in excavation by mechanical means (hydraulic excavator)/manualmeans over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer-in-charge - all kinds of soil cum 1 15.40 177.50 2,733.50 3 2.25 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. cum 1 1.69 196.00 332.02 4 4.1 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 5 4.1.8 1:4:8 (1 cement : 4 coarse sand (zone-iii) : 8 graded stone aggregate 40 mm nominal size) cum 1 3.08 6,812.00 20,980.96 doors/windows/glazing/panelling 6 21.18 providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of engineer-in-charge (door handle, lock and stopper etc.to be paid separately) sqm 2 22.5 5,325.90 1,19,832.75 7 mr-1 sliding glazed door: providing, installation, testing & commissioning of bi-parting automatic sliding door operator complete with a pair of bi-parting doors and two fixed side screens. the door is activated by radar units mounted either side of the threshold sqm 1 22.30 10,430.24 2,32,594.36 8 9.147.a4.1 upvc window: providing & fixing upvc sliding windows 3-track minimum 2.5mm gauge (medium) (fenestech /torfenster or of approved make) with 6mm glass with all fittings like rollers, locking arrangement, beading, handle etc. & required hardware of approved quality, etc. sqm 1.00 3.30 10,993.55 36,278.72 9 mr-2 wall panelling - providing & fixing panelling as per drawing made out of frame both ways horizontally and vertically with 6mm thk.marine plywood with 1mm thk laminate of aproved shade. the skirting should be asper approved laminate as per drawing and direction,therateis including all necessary fitting and fixtures gluing material and other hardware incluiding cleaning, etc complete. note.:as per detailed drawing given by architect / instructions given by architect on site etc. complete. sqm 1.00 624.72 14,155.33 88,43,115.54 brick work 10 6.1 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 cement mortar 1:4 (1 cement : 4 coarse sand) 9.74 7,370.65 71,793.82 11 6.4. brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : 6.4.1 cement mortar 1:4 (1 cement : 4 coarse sand) 18.30 9,344.35 1,71,020.29 marble & granite works 12 8.2.2.2 providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish 63.91 5,136.30 3,28,260.93 13 8.15 providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. (250g each cramp wt) kg 100 25 714.40 17,860.00 14 8.16 providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. each 90.00 90.00 43.90 3,951.00 9 wood & pvc work 15 9.1.2 providing wood work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid for seperately) - sal wood cum 11 0.726 1,16,520.30 84,593.74 16 9.7 providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25mm to 40mm thick 17 9.7.3.1 plywood 5ply, 9mm thick - decorative plywood both side decorative veneer (type - 1) conforming to is 1328 bwr type sqm 11 27.72 2,724.25 75,516.21 18 9.100 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 19.0 9.100.1 125mm nos 11 11 66.25 728.75 20 9.101 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 21.0 9.101.1 single rubber stopper nos 15 15 39.60 594.00 22 9.113 providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of engineer- in-charge. nos 2 2 850.05 1,700.10 10 steel work 23 10.25 steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 24.0 10.25.2 in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 50.00 50.00 172.60 8,630.00 13 finishing work 25 13.4 12 mm cement plaster of mix : 13.4.2 1:6 (1 cement: 6 coarse sand) sqm 85.600 343.65 29,416.44 26 13.16 6 mm cement plaster of mix : 13.16.1 1:3 (1 cement: 3 fine sand) sqm 39.40 300.45 11,837.73 27 13.41 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 28 13.41.1 new work (two or more coats) over and including water thinnable priming coat with cement primer sqm 1 500.000 185.65 92,825.00 29 13.47 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: 30 13.47.1 new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) sqm 1 500.000 171.10 85,550.00 31 13.80 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to sqm 1 100.00 156.05 15,605.00 32 13.62 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.62.1 two or more coats on new work sqm 1 500.00 226.25 1,13,125.00 21 aluminium, glazing & italian marble works 33 21.8 filling the gap in between aluminium frame & adjacent rcc/ brick/stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of engineer-in-charge complete. 21.8.1 upto 5mm depth and 5 mm width rmtr 4 80 96.75 7,740.00 34 8.11.1 providing and fixing 18mm thick italian marble stone machine cut, mirror/ eggshell polished, marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with the cement slurry @3.3kg/sqm including the point with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing, etc. all complete as per architectural drawings and as directed by engineer-in-charge. sqm 1 165 10,414.80 17,18,442.00 35.0 11.51.1 providing and laying machine cut, mirror polished, italian marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge - 18 mm thick italian marble stone slab, perlato, rosso verona, fire red or dark emperadore etc. 36.0 25.8 design supply & installation of suspended spider glazing system designed to withstand the wind pressure as per is 875 (part-iii). the suspended system held with spider fittings of ss-316 grade steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with ss- 316 grade stainless steel spider & bolt assembly with laminated glass fins 21 mm thick. the glass fins and glass panel assembly shall be connected to slab/beams by means of ss- 316 grade stainless steel brackets & anchor bolts and at the bottom using ss channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. the complete system to be designed to accommodate thermal expansion & seismic movements etc. the joints between glass panels (6 to 8 mm) and gaps at the perimeter & in u channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. the rate shall include all design, engineering and shop drawing including approval from structural designer, labour, t&p, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, buffer plates, fastener, anchors, ss channel laminated glass etc. all complete. for the purpose of payment, actual elevation area of glazing including thickness sqm 1 244 9,502.32 23,18,566.08 37 26.26.2 providing & fixing false ceiling 12.5mm thick gypboard ceiling surfaces in plain including g.i. suspenders forming a grid of intermediate channel at 1220mm centre to centre with ceiling sections fixed at 450mm centre to centre at right angle to the underside of intermediate channels with connecting clips complete as per india gypsum technical manual including finishing with jointing compound and joint paper tapes and priming with two coats of drywall top coat and fixing of perimeter channel at both ends. the rate shall also include cutting the gypboard for light fixtures/a.c. diffusers etc. and providing necessary and additional frame work for fixing the same. whereever perimeter channels are cut in this process, additional support shall be made for proper stability without any extra cost. the work shall be carried out as per specifications, drawing and as sqm 1.00 504.00 1,907.35 9,61,304.40 38 13.83.2 wall painting with premium acrylic emulsion paint of interior grade, having voc (volatile organic compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour - two coats sqm 1.00 300.00 142.80 42,840.00 demolition work 39 15.14.1 dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : of sectional area 40 square centimetres and above cum 2.00 1.68 4,459.10 7,491.29 40 15.25 dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. sqm 1.00 528.00 266.45 1,40,685.60 41 15.39.2 dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : thickness above 10 mm up to 25 mm sqm 3.00 24.00 77.75 1,866.00 42 15.7.4 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge - in cement mortar cum 3.00 4.10 ground floor walls for reception cum 1.00 27.95 32.05 2,060.20 66,027.35 43 15.12.1 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking nos 8 8 367.20 2,937.60 44 15.57 dismantling aluminium/ gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by engineerin- charge. 449.00 56.40 25,323.60 45 15.19 dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of engineer-in-charge. 46.0 at staircase 15mmx20mm ms rods @ 7 nos per flight density - 7850 kg/cum 112.00 0.067 kg 0.067 525.95 3.85 2,024.91 47 mr-3 reception : 4500x800 ,providing reception table as per design on site in 19 mm marine plywood frame work with 1 mm thk vineer table top, including 12 mm thk. glossy onyx alabaster film set 1 1 5,19,103.39 5,19,103.39 48 reception : 4000x800 ,providing reception table as per design on site in 19 mm marine plywood frame work with 1 mm thk vineer table top, including 12 mm thk. satvario quartz on table top rested 49 14.72 providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia m.s. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with m.s. tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .the scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in-charge .the elevational area of the scaffolding shall be measured for payment purpose.the payment will be made once irrespective of duration of scaffolding .... more in document

State Government

TRN :49061186 | 25 May, 2025

Tender Value : 0

Mandi - Himachal Pradesh

Tender for tender for supply of 1. sand crusher per cum, 2. river sand per cum, 3. reva plot dissolved sand per cum, 4. crusher gravel 10mm, 20mm, 40mm per cum, s. soling stone per cum, 6. gutka stone 40. 75 per cum, 2. pakki bricks 1000 nos, 8. jaisni chuck per hour, 9. jcb loader per houes, 10. jcb hammer per hours 11. cricket mixer rent per day 12 water tank 3000 liter capacity per tech. 13. shuttering steel rent per square metre, 14. wooden shuttering rent per square metre, 15. wooden shuttering stall rent per square metre, 16. motoring stall rent per kilometre, 17. rcc hume pipe np 3 with collar 300mn per no. 18. rcc hume pipe np3 with cokkar 45mm per no. 19. rcc hume pipes npx with collar 900mm 20. sign board concrete with painting sitting 3 foot, 4 foot per no. 21. moment carriage from civil supply store to gram panchayat per bang, 22. sitting bench concrete per no.

Central Government/Public Sector

TRN :49068676 | 28 May, 2025

Tender Value : 20.00 Lacs

Bikaner - Rajasthan

Tender for tender for welcome maintenance to officers md accommodation at af station nal; 1 demolition of brick or stone masonary built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed. 2 material and labour brick work with sub class -b bricks old size, straight or curved on plan exc 6m mean radiusbuilt in cm 1:6. complete all as specified & directed. 3 all as per serial item no. 2.00 (here in before) but as in half brick thick walls built in cement mortar 1:4. 4 taking down chawkhat or frame with shutter (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed. 5 taking down chawkhat or frame with shutter (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.0 sqm each complete all as specified and directed. 6 taking down door shutter of any description exc 1.00 sqm but n. exc. 2.00 sqm each complete all as specified and directed. 7 taking down wooden shutters of any description exc 1 sqm but n.exc 2 sqm each from chowkhat and re-fixing in same opening after re-securing or easening and adjusting including repair of hinge as required complete all as specified and directed. 8 s&f solid pvc door frame of size 50mm x 47mm made out 5mm both side prelam pvc sheet used instead of plain colour pvc sheet & edges will be painted to match with prelam sheet re-inforced with ms square tube complete all as specified and directed. 9 m&l for factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of ms tubes 40mm x 20 mm for top and bottom rails ms frame shall be covered with heat moulded prelam pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour pvc sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottam rail both side prelam pvc sheet used instead of plain colour pvc sheet. stile and rails feathered at edges paneling of prelam solid pvc sheets 10mm thick to be filted in msframe 40 x 20 mm welded, sealed to the stiles and rails with suitable pvc sheet beading, and jointed together with the solvent cement complete all as specified and directed. 10 s&f 1.25 mm thick pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c-0 using 12.5 mm graded stone aggregate complete all as specified and directed. 11 s&f 1.25 mm thick pressed steel frames of size 105mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c-0 using 12.5 mm graded stone aggregate complete all as specified and directed. 12 s&f 35 mm thick 2nd class hard wood factory made plain framed, pannelled shutter (any number of panels) with panel of timber flat on both sides (feather edged) or of 12mm thick bwp commercial plywood with commercial face veneers, supplied and fitted complete all as specified and directed. 13 supply and fixing glazed and gauged skeleton factory made shutters35mm thick, 2nd class hard wood hollockopen rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cutand mitred beads for securing glass etcincl priming coat. the size of member of shutters as spfd in ssr part-1 section 8 clause 8.20 (b) incl kiln seasoned and chemically pressure treated, complete all as specified & directed. 14 s&f30mm factory made thick flush shutters, solid core construction,with particle board coreand plywood face panels,commercial type on both face is covered with decorative face veneer with lipping/frame to match sides includeforthe provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specified and directed. 15 s&f butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, 100mm size, isi marked, complete all as specified & directed. 16 supply and fixing200mm size aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. 17 supply and fixing 150mm sizeextruded aluminium alloy handles, fabricated type, anodised aluminium handles, complete all as specified and directed. 18 supply and fixing 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. 19 supply& fixingas in repairfloor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed to door shutters,complete all as specified and directed. 20 supply and fixing galvanised stainless steel wire cloth 0.45mm nominal dia of wire and width of aperture 1.40mm and fixed with tinned tacks or galvanised wire stapples/ screws in metal surrounds as required fixedcomplete all as specified and directed. 21 all as per description of serial item no. 20 here in before but as in repair 22 hacking out old broken glass of any thickness/size of any description from wooden frames/metal frame glazed with putty or fixed with beads all as specified. 23 supply and fixing 3mm thick sheet glass, ordinaly quality and glazing with oil putty or secured with spring clips in metal surrounds as required in square n exc 0.5 sqm in each pane , complete all as specified and directed. 24 all as per description of serial item 23 here in before but figured glass, pin head type. 25 s&f as in repairs door closer hydraulically regulated cast iron body, designation no 2, universal type, suitable for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg,complete all as specified and directed. 26 s&f as in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller pleat complete all as specified and directed. 27 s&f in repair stainless steel (grade 305) curtain rods 25mm dia 0.80mm wall thickness mild steel chromium plated incl supporting brackets complete all as specified and directed. 28 s&f in repair stainless steel (grade 305) ornamental type brackets (open ends) suitable for curtain rods of 25mm dia all as specified and directed. 29 s&f in repair stainless steel (grade 305) brackets (dead ends) suitable for curtain rods of 25mm dia all as specified and directed. 30 demolition of cement concrete in any positionand removing the rubbish outside mod land complete all as specified anddirected. 31 m&l for pcc (1:3:6) type c-2, using 40mm graded stone aggregate as in plinth protection 75mm thick laid in bays including all necessary form work, finishing exposed edges fair and providing 10 mm wide joints throughout the thickness of plinth protections duly filled with matic filling(one part of hot bitumen 85/25 and three parts of sand)and surfaces finished even & smooth without using extra cement complete all as specified . 32 m&l 25mm thick pcc 1:2:4 type b-0(using 12.5mm graded stone aggregate)as in sub base of floor surface finished even rough to receive floor topping complete all as specified and directed. 33 dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed. 34 m&l for granite (of any type)slab 18-20 mm thick machine cut ,bedded and jointed with gray cement slurry and pointed with white cement as in floors/ cooking plateform, with admixiture of pigment to match the shade of granite stone including grindingand polishing complete over and including20 mm thick screed bed in cm 1:6 complete all as specified . 35 m&l for granite (of any type)slab 18-20 mm thick machine cut , jointed with gray cement slurry and pointed with white cement as in vertical surfaces / dado / skirtingwith admixiture of pigment to match the shade of granite stone indluding grindingand polishing complete over and including10 mm thick backing coat in cm 1:4 complete all as specified . 36 m& l green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, including grinding and polishing providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete complete complete all as specified and directed. 37 dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified. note:-the demolished material should be disposed off out side the mod land. the contractor shall quote his rates considering the above element 38 material and labour for glazed ceramic coloured tiles 7 to 8mm thick (square/rectangular )in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm thick set & jointed in neat gray cement slurry and pointed with coloured cement to match,the sahde of tiles laid over and including 10mm thick rendering in cm 1:4 complete all as specified and directed. 39 material and labour non-skid, ceramic coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,as in floors, set and jointed ingray cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 40 material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,as in floors, set and jointed ingray cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 41 material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed ingray cement slurry and pointed in white or coloured cement to matchthe shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in cm (1:4) complete all as specified and directed. 42 m&l for vitrified light shade ceramictiles9 to 10 mm thick polished,area of each tile exc 0.18 sqm andn exceeding 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cm 1:6 complete all as directed by engr-in-charge. 43 all as per ser item no.42 (here in before) but as in skirting laid over and including 10mm cement backing in cm 1:4. 44 material and labour for repairing of soffits of slabs/chajja, facia and similar works by dismantling of loose/ disintegrated portion of rcc upto 7.5 mtr heightand in any sitution, including provn of support,formwork and welding of reinforcement and fixing in position and with provision of weld mesh, applying dubbing 1st coat of 20 to 25mm thick in cm 1:3 finished rough and finishing coat of 10mm thick in cm (1:3) finished even and smooth without using extra cementover and including cement slurry @ 3 kg/sqm, finished even and smooth to desired shapeand applyingtwo coats of weather proof exterior emulsion paint over a coat of arylic resistant primer to match with existing surfaces complete all as specified and directed.(weld mesh measured and paid sepatrtely)note:-(i) unit rate of this item includes the cost of scaffolding, formwork etc. and nothing extra shall be paid on account of variation in height.(ii) for payment purpose, the area of finished plaster in 2nd coat shall be considered. 45 material and labour for hard drawn steel wire fabric (weld mesh) of weight not less than 3 kg/ sqm and not exc 4 kg/ sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt including necessary fixing arrangements etc complete all as specified and directed. 46 taking down cementplaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down down with water etc complete all as specified and directed. note:- the demolished materials should be disposed off at a site as described by the eng-in-charge. the contractor shall quote his rates considering the above element. 47 m&l for rendering 10 mm thick on ceiling (brick or concrete surfaces)in cement mortar 1:4 and surface finished even and smooth without using extra cement complete all as specified and directed. 48 m&l for rendering 15mm thick on brick or concrete surfaces in cement mortar 1:6, finishing surfaces even and smooth without using extra cement complete all as specified and directed. 49 m&l forrendering 15mm thick on brick or concrete surfaces other than fair face of brick work in cement mortar 1:4, finishing surfaces even and smooth without using extra cement complete all as specified and directed. 50 m&l for applying three coats of white wash on newly plasteredsurfaces of ceiling including preparation of surfaces complete all as specifed and directed. 51 m&l for preparation of newly plastered or unplastered surfaces of walls and applying two coats of exterior acrylic emulsion in any pattern (approved by ge), paint over and including a coat of exterior primer complete all as specified and directed. 52 m&l for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted over and including a coat of primer complete all as specified and directed. 53 material & labour for prepapration of new or previously untreated surfaces of wood or wood based materials of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over & including a coat of pink primer comlplete all as specified and directed. 54 material & labour for prepapration of new or previously untreated steel or iron surfaces of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over & including a coat of red oxide primer comlplete all as specified and directed. 55 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified. 56 material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling etc. incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified. 57 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of oil bound distemper complete all as specified & directed. 58 material and labour for comple removal ofold decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying two coats of oil bound distemper complete all as specified & directed. 59 m&l for complete removal of existing treatment on walls and applying two coat ofoil bound distempe paint interior gradeover & including a coat of alkali resistant priming paint over 7 including two layer of birla wall putty (min thickness 3mm) incl filling in craks etc to achieve a uniformsmooth finish incl preparationof surfaces complete all as specified & directed . 60 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of plastic emulsion complete all as specified & directed. 61 m&l for preparation of old painted surface of wood and wood based materials of any description not otherwise described over 10 cm. width or girthshallapplying one coat of synthetic enamel painting overthe wooden surfaces all as specified & directed. 62 m&l for preparation of old painted surfaces of steel and iron work of any description exc 10 cm width or girth applying one coat of synthetic enamel paint on steel surface all as specified. 63 taking up or down 15 mm bore steel tubing & connections including clearing for refixing or removal to store complete all as specified and directed. 64 all as perserial item 63 here in before but 20m bore tubes 65 supply and fixing15mm bore tubes “medium grade”, galvanized, with and including all fittings and fixed completetowalls and ceilings or laid in floors,complete all as specified and directed. 66 all as per serial item 65 here in before but 20m bore tubes 67 s&f as in repair pillar taps long body fancy type quarter turn with capasten head chromium plated screwed down high pressure with without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. 68 supply and fixing as in repairs bib cock quarter turn cast copper alloy chromium plated, fancy type, long body screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 69 s & f as in repairs two way angle cock quarter turn cast copper alloy 15 mm bore chromiun plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. 70 s & f as in repairs angle cock quarter turn cast copper alloy 15 mm bore chromiun plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. 71 supply and fixing as in repair central hole basin mixer long swang nack, without poup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 72 supply and fixing as in repair central hole sink mixer long body swang nech for mixing hot & cold water, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 73 s&f as in repair brass cp wall mixer 3-in-1 system with provision for both hand shower and over head shower complete with 115mm long bend pipe, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. 74 s&f as in repair brass cp wall mixer 2-in-1 system with provision for over head shower complete with 115mm long bend pipe on upper side, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. 75 supply & fixingas in repair chromium platedshower rose with or without swivel joints 125mm dia including fixing to steel pipe,complete all as specified and directed. 76 supply& fixing as in repair toiletpaper holder of brass chromium plated, complete all as specified and directed. 77 supply& fixing as in repairs pvc (ptmt) float valve,high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe,complete all as specified and directed. 78 supply& fixing as in repairs pvc waste down pipeof 32/40 mm bore for basin, complete all as specified and as directed. 79 supply and fixing as in repairs 15mm dia pvc connection of length 450 mm, with ptmt nut, complete all as specified and directed. 80 supply and fixing as in repairs faucet health (hand jet) 15mm bore cast copper alloy, chromium plated with flexible chromium plated connection pipe 1.5 mtr length, with fittings, complete all as specified and directed. 81 supply& fixingas in repairs wash hand basin, vitreous china, white, decorative type, flat or angleback, size 580mm x 450mm inclusive ofwaste pipe and brass coupling and including cutting for and pinning in ends of brackets or erecting stand and inclusive of cost of brackets complete all as specified and directed. 82 s&f as in repair vitreous china pedastal pattern, wc incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete all as specified and directed. 83 s&f in repair rimless single piece wc with uf soft close slim seat cover, hinges, fixing accessories set , incl cisternfittings, size 385x720x715mm complete all as specified directed by engr-in-charge. make: jaguar/cera/hindware 84 supply and fixing as in repair pvc valve less syphonic action type flushing cistern low level white with pvc in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including pvc connection and 32mm dia pvc long bend for squat pattern etc, set with concrete and making good to floor including taking down existing, fixed as in repairs complete all as specified & directed. 85 s&f as in repair ptmt seat cover white colour for padastal pattern,incl connection nut & bolts, etc. complete all as specified and directed. 86 s&f as in repair sinks with drain board made of stainless steel sink of 1mm thick sheet, kitchen or laboratory with plug washer and waste pipe incl bedding in cement mortar 1:6 on to draft wall of including fixing cantilever brackets and connecting unions overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed as in repairs complete all as specified. 87 supply& fixingas in repair pvc bath cabinet, size 622mm x 422mm, comprising of lookingglass, space for bath soaps, shampoo, tooth brush and paste, hand towel rail, complete all as specified and directed. 88 supply and fixing in repair stainless steel towel rack 600mm long with lower hangers incl 3 hooks complete all as specified and directed. 89 supply and fixing in repair brass chromium plated tubular towel rail 20mm dia d type 60 cm long between flanges complete all as specified and directed. 90 supply and fixing as in repair soap dish chromium plated of size 100 x 100 mm any type, fixed with chromium plated brass screwscomplete all as specified and directed. 91 s & f as in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed. 92 s&f as in repairs corner glass shelf with cp brackets (3 pcs set having size 8,10 & 12)complete all as specified and directed. 93 demolition and breaking up drain pipes 110/75 mm bore (salt glazed ware, ac or reinforced concrete) set in cement mortar complete all as specified and directed. 94 s&f 110mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to wall &laid in trenches or in floors,including clamps as required, complete all as specified and directed. 95 s&f 75mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to wall &laid in trenches or in floors,including clamps as required, complete all as specified and directed. 96 s&f in repair 75mm dia pvc (swr) floor trap plain with cp grating including jointing with solvant cement incl necessary pcc & form work as required complete all as specified and directed. 97 s&f 75mm dia pvc (swr) bends with rubber ring joints fixed as required with oval access door complete all as specified and directed. 98 s&f 110mm dia pvc (swr) bends with rubber ring joints fixed as required with oval access door complete all as specified and directed. 99 s & f 110mm bore pvcswr junction single (single t) with access door complete all as specified and directed 100 s&f in repairs stainless steel plate rack of size 78cmx91cmx25cm made out of 0.80 mm thick of stainless steel sheet , fixed in wall with rawl plugs and screws complete all as specified and directed. 101 dismantling boarding, any description any size , fixed in any position with screws complete all as specified . 102 m& l for 18 mm thick pvc board celuka ply of density 600kg/cum one side prelam/rigid laminated (colour/shade as approved by engr-in-charge) and other side plain white colour to make kitchen cabinet shutters /shelves/partitions and incl all required brackets ss screws etc, approved by engr-in-charge. 103 m& l for 18 mm thick pvc board celuka ply of density 600kg/cum both sidesplain white colour to make kitchen cabinet shutters/shelves/partitions and all required brackets ss screws etc, approved by engr-in-charge. 104 s&fin repair auto closes clip on cabinet hinges (regular) for kitchen cabinet shutters note : each pair means one piece fixed on openable shutter and other piece fixed on fixed portion. 105 s&fin repair stainless steel (ss 304) handles 100 mm size for kitchen cabinet shutters. 106 s&fin repair ball bearing drawer channel telescopic type (500mm) full extention load of load bearing capacity 45 kg.note : each pair means 2 nos of telescopic channel, one piece fixed on left side and another piece fixed on right side. 107 s&f rab door seal bottom brush duststopper with aluminium plate nylone brush of selected colour for fit each complete all as specified and directed. note : the sample of item shall be approved by ge before placing at site 108 supply and fixing powder coated aluminium (minimum thickness of powder coating 50micron) work for frames of doors, windows,ventilators and partitions (fixedportions) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge note:-for payment purpose weight of aluminium section will only be measured 109 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings such as hinges,handle,tower bolt,sliding boltshall be paid for separately) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws,rollers & dust proof brush for sliding door / windowcomplete all as per architectural drawings and the directions of engineer-in-charge note:-for payment purpose weight of aluminium section will only be measured 110 s & f as aluminium grill of size, 85mm x 85mm hexagonal shaped mesh, fixed to aluminium frame work with u clip of size 15mmx12mm & fastners complete all as specified and directed. 111 s & f4.80 mm thick sheet glass ofordinary quality plain / tintedand glazing with rubber beads, clips etc complete all as specified and directed. 112 s & f 3 mm thickhigh quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed. 113 s & f double action floor door spring hydraulically regulated made up minimum1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, with governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified 114 s&f conceled lock (push to unlock) for sliding window made with zinc body, aluminium hook and anti rust material with power coated metallic finish of approved colour having size100mm x 24 mm incl necessary cutting for fixing all as specified and directed.

State Government

TRN :49023607 | 16 May, 2025

Tender Value : 22.62 Lacs

Lucknow - Uttar Pradesh

Tender for tender for construction and renovation work of community center located in sector-d of kanpur road scheme - rcc repairs 2 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge. 3 75mm average thickness 4 50mm average thickness 5 25 mm average thickness 6 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 7 bars upto 12 mm diameter 8 bars above 12 mm diameter 9 drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in rcc beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer-in-charge.upto and including 12mm dia. 10 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect.epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 11 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge.note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 12 25 mm average thickness in 2 layers. 13 50 mm average thickness in 3 layers. 14 providing and laying sbr polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structuralmembers e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of rcc member.note: rates shall be for finished surface area of concrete and shall include the cost of making holes in existing rcc slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved super-plasticiser forrendering concrete as flowable self compacting and sbr polymer but shall exclude cost of reinforcement, bond coat, shear keys, centering and shuttering, strutting, propping etc (payment under this item shall be madeonly after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) 15 50mm thick in grade m 25 with cement content not less than 330 kg per cum 16 75mm thick in grade m 25 with cement content not less than 330 kg per cum 17 100mm thick in grade m 25 with cement content not less than 330 kg per cum 18 providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge.(the payment shall be made on the basis of actual weight of approved grout injected.) 19 epoxy injection grout in concrete/rcc work of approved make 20 providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the engineerin- charge.wooven pvc cloth 21 shotcreting r.c.c. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stoneaggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by engineer- in-chargenote: rates shall include the providing necessary ground wires etc. the levelling gauges, if used, shall be paid for separately. payment under this item shall be made only after proper wet curing has been done and surface hasbeen satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 22 50mm thick in grade m 25 with cement content not less than 330 kg per cum 23 75mm thick in grade m 25 with cement content not less than 330 kg per cum 24 providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of engineer-in-charge. 25 providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 26 mild steel or iron work in plain work such as in r.c.c. or r.b. (when not included in an over all rates ) including bending for proper completion of the workand including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. 27 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 28 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 29 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thic 30 waterproofing and terracing 31 providing and laying in situ five course water proofing treatment with app (atactic polypropylene) modified polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to is : 702, 3rd layer of roofing membrane app modified polymeric membrane 2.0 mm thick of 3.00 kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron hmhdpe film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron hmhdpe film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 33 miscellaneous works 34 providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, includingadditional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia m.s. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with m.s. tubes, m.s. tube challis, m.s. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of engineer-in-charge.note:- (1) the elevational area of the scaffolding shall be measured for payment purpose. (2) the payment will be made once only for execution of all items for such works. 35 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. 36 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 37 cleaning of under ground sump, over head r.c.c. tank ( independent staging) including disposal of slit and rubbish, all as per direction of engineer-in-charge.the cleaning shall consist following operations:-(i) tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits.(ii) entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water.(iii) chlorination of rcc internal surface by liquid chlorine.(iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.(v) finally the surface shall be treated with ultraviolet radiation etc. as per direction of engineer-in-charge. 38 door-window repair 39 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) 40 renewal of old putty of glass panes (length) 41 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead asper direction of engineer - in- charge. 42 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer-in-charge. 43 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar 44 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres 45 casement door double panel with french (false) mullion with zinc alloy (zamak) 3d hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.using r4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above ) x (100 mm& above) & french (false ) mullion (64mm & above) x (60 mm & above). (height above 2.5 metre) 46 toughened glass 12 mm thickness 47 finishing work 48 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 49 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 50 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 51 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 52 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 53 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 54 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 55 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 56 washrooms 57 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 58 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 59 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including isi marked stainless steel butt hinges with necessary screws 60 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 61 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 62 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Related Searched Keywords : plastic shutters

List of plastic-shutters Tenders

Get plastic shutters Tender Alert...

Related Searched Keywords : plastic shutters

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us